* [PATCH v2 2/6] omap3: pm: Using separate clk/volt setup_time for RET and OFF states
@ 2010-01-19 17:35 x0080970
2010-01-21 7:27 ` Nishanth Menon
0 siblings, 1 reply; 2+ messages in thread
From: x0080970 @ 2010-01-19 17:35 UTC (permalink / raw)
To: linux-omap; +Cc: Lesly A M, Nishanth Menon, David Derrick, Samuel Ortiz
From: Lesly A M <x0080970@ti.com>
omap3: pm: Using separate clk/volt setup_time for RET and OFF states
Copied the setuptime in each board file, since OMAP3430 & OMAP3630
has different voltage levels for the same states.
Made the changes to program the setup time according to
the target state of CORE power domain.
The voltsetup2 is used only when the device exits sys_off mode
(with PRM_VOLTCTRL[3]SEL_OFF set to 1).
Signed-off-by: Lesly A M <x0080970@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: David Derrick <dderrick@ti.com>
Cc: Samuel Ortiz <sameo@linux.intel.com>
---
arch/arm/mach-omap2/board-3430sdp.c | 14 ++++--
arch/arm/mach-omap2/board-3630sdp.c | 25 ++++++++++
arch/arm/mach-omap2/board-zoom-peripherals.c | 4 +
arch/arm/mach-omap2/board-zoom2.c | 25 ++++++++++
arch/arm/mach-omap2/board-zoom3.c | 25 ++++++++++
arch/arm/mach-omap2/include/mach/board-zoom.h | 2
arch/arm/mach-omap2/pm.h | 11 +++-
arch/arm/mach-omap2/pm34xx.c | 60 +++++++++++++++++++++-----
8 files changed, 143 insertions(+), 23 deletions(-)
Index: linux-omap-pm/arch/arm/mach-omap2/board-3430sdp.c
===================================================================
--- linux-omap-pm.orig/arch/arm/mach-omap2/board-3430sdp.c 2010-01-19 19:18:55.000000000 +0530
+++ linux-omap-pm/arch/arm/mach-omap2/board-3430sdp.c 2010-01-19 19:19:23.000000000 +0530
@@ -75,13 +75,19 @@
{1, 10000, 30000, 300000},
};
-/* FIXME: These are not the optimal setup values to be used on 3430sdp*/
+/* FIXME: These are not the optimal setup values to be used on 3430sdp */
static struct prm_setup_vc omap3_setuptime_table = {
- .clksetup = 0xff,
- .voltsetup_time1 = 0xfff,
- .voltsetup_time2 = 0xfff,
+ /* CLK SETUPTIME for RET & OFF */
+ .clksetup_ret = 0xff,
+ .clksetup_off = 0xff,
+ /* VOLT SETUPTIME for RET & OFF */
+ .voltsetup_time1_ret = 0xfff,
+ .voltsetup_time2_ret = 0xfff,
+ .voltsetup_time1_off = 0xfff,
+ .voltsetup_time2_off = 0xfff,
.voltoffset = 0xff,
.voltsetup2 = 0xff,
+ /* VC COMMAND VALUES for VDD1/VDD2 */
.vdd0_on = 0x30,
.vdd0_onlp = 0x20,
.vdd0_ret = 0x1e,
Index: linux-omap-pm/arch/arm/mach-omap2/board-3630sdp.c
===================================================================
--- linux-omap-pm.orig/arch/arm/mach-omap2/board-3630sdp.c 2010-01-19 19:18:55.000000000 +0530
+++ linux-omap-pm/arch/arm/mach-omap2/board-3630sdp.c 2010-01-19 19:19:23.000000000 +0530
@@ -25,6 +25,29 @@
#include "mux.h"
#include "sdram-hynix-h8mbx00u0mer-0em.h"
+#include "pm.h"
+
+static struct prm_setup_vc omap3_setuptime_table = {
+ /* CLK SETUPTIME for RET & OFF */
+ .clksetup_ret = 0xff,
+ .clksetup_off = 0xff,
+ /* VOLT SETUPTIME for RET & OFF */
+ .voltsetup_time1_ret = 0xfff,
+ .voltsetup_time2_ret = 0xfff,
+ .voltsetup_time1_off = 0xfff,
+ .voltsetup_time2_off = 0xfff,
+ .voltoffset = 0xff,
+ .voltsetup2 = 0xff,
+ /* VC COMMAND VALUES for VDD1/VDD2 */
+ .vdd0_on = 0x28, /* 1.1v */
+ .vdd0_onlp = 0x20, /* 1.0v */
+ .vdd0_ret = 0x13, /* 0.83v */
+ .vdd0_off = 0x00, /* 0.6v */
+ .vdd1_on = 0x2B, /* 1.1375v */
+ .vdd1_onlp = 0x20, /* 1.0v */
+ .vdd1_ret = 0x14, /* 0.85v */
+ .vdd1_off = 0x00, /* 0.6v */
+};
#if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
@@ -97,7 +120,7 @@
static void __init omap_sdp_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
- zoom_peripherals_init();
+ zoom_peripherals_init(&omap3_setuptime_table);
board_smc91x_init();
enable_board_wakeup_source();
usb_ehci_init(&ehci_pdata);
Index: linux-omap-pm/arch/arm/mach-omap2/board-zoom-peripherals.c
===================================================================
--- linux-omap-pm.orig/arch/arm/mach-omap2/board-zoom-peripherals.c 2010-01-19 19:18:55.000000000 +0530
+++ linux-omap-pm/arch/arm/mach-omap2/board-zoom-peripherals.c 2010-01-19 19:19:23.000000000 +0530
@@ -26,6 +26,7 @@
#include "mux.h"
#include "mmc-twl4030.h"
+#include "pm.h"
/* Zoom2 has Qwerty keyboard*/
static int board_keymap[] = {
@@ -271,10 +272,11 @@
OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
}
-void __init zoom_peripherals_init(void)
+void __init zoom_peripherals_init(void *peripheral_data)
{
omap_i2c_init();
omap_serial_init();
usb_musb_init();
enable_board_wakeup_source();
+ omap3_pm_init_vc((struct prm_setup_vc *)peripheral_data);
}
Index: linux-omap-pm/arch/arm/mach-omap2/board-zoom2.c
===================================================================
--- linux-omap-pm.orig/arch/arm/mach-omap2/board-zoom2.c 2010-01-19 19:18:55.000000000 +0530
+++ linux-omap-pm/arch/arm/mach-omap2/board-zoom2.c 2010-01-19 19:19:23.000000000 +0530
@@ -26,6 +26,29 @@
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "omap3-opp.h"
+#include "pm.h"
+
+static struct prm_setup_vc omap3_setuptime_table = {
+ /* CLK SETUPTIME for RET & OFF */
+ .clksetup_ret = 0xff,
+ .clksetup_off = 0xff,
+ /* VOLT SETUPTIME for RET & OFF */
+ .voltsetup_time1_ret = 0xfff,
+ .voltsetup_time2_ret = 0xfff,
+ .voltsetup_time1_off = 0xfff,
+ .voltsetup_time2_off = 0xfff,
+ .voltoffset = 0xff,
+ .voltsetup2 = 0xff,
+ /* VC COMMAND VALUES for VDD1/VDD2 */
+ .vdd0_on = 0x30,
+ .vdd0_onlp = 0x20,
+ .vdd0_ret = 0x1e,
+ .vdd0_off = 0x00,
+ .vdd1_on = 0x2c,
+ .vdd1_onlp = 0x20,
+ .vdd1_ret = 0x1e,
+ .vdd1_off = 0x00,
+};
static void __init omap_zoom2_init_irq(void)
{
@@ -82,7 +105,7 @@
static void __init omap_zoom2_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
- zoom_peripherals_init();
+ zoom_peripherals_init(&omap3_setuptime_table);
zoom_debugboard_init();
}
Index: linux-omap-pm/arch/arm/mach-omap2/board-zoom3.c
===================================================================
--- linux-omap-pm.orig/arch/arm/mach-omap2/board-zoom3.c 2010-01-19 19:18:55.000000000 +0530
+++ linux-omap-pm/arch/arm/mach-omap2/board-zoom3.c 2010-01-19 19:19:23.000000000 +0530
@@ -24,6 +24,29 @@
#include "mux.h"
#include "sdram-hynix-h8mbx00u0mer-0em.h"
+#include "pm.h"
+
+static struct prm_setup_vc omap3_setuptime_table = {
+ /* CLK SETUPTIME for RET & OFF */
+ .clksetup_ret = 0xff,
+ .clksetup_off = 0xff,
+ /* VOLT SETUPTIME for RET & OFF */
+ .voltsetup_time1_ret = 0xfff,
+ .voltsetup_time2_ret = 0xfff,
+ .voltsetup_time1_off = 0xfff,
+ .voltsetup_time2_off = 0xfff,
+ .voltoffset = 0xff,
+ .voltsetup2 = 0xff,
+ /* VC COMMAND VALUES for VDD1/VDD2 */
+ .vdd0_on = 0x28, /* 1.1v */
+ .vdd0_onlp = 0x20, /* 1.0v */
+ .vdd0_ret = 0x13, /* 0.83v */
+ .vdd0_off = 0x00, /* 0.6v */
+ .vdd1_on = 0x2B, /* 1.1375v */
+ .vdd1_onlp = 0x20, /* 1.0v */
+ .vdd1_ret = 0x14, /* 0.85v */
+ .vdd1_off = 0x00, /* 0.6v */
+};
static void __init omap_zoom_map_io(void)
{
@@ -66,7 +89,7 @@
static void __init omap_zoom_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
- zoom_peripherals_init();
+ zoom_peripherals_init(&omap3_setuptime_table);
zoom_debugboard_init();
omap_mux_init_gpio(64, OMAP_PIN_OUTPUT);
Index: linux-omap-pm/arch/arm/mach-omap2/include/mach/board-zoom.h
===================================================================
--- linux-omap-pm.orig/arch/arm/mach-omap2/include/mach/board-zoom.h 2010-01-19 19:18:55.000000000 +0530
+++ linux-omap-pm/arch/arm/mach-omap2/include/mach/board-zoom.h 2010-01-19 19:19:23.000000000 +0530
@@ -2,4 +2,4 @@
* Defines for zoom boards
*/
extern int __init zoom_debugboard_init(void);
-extern void __init zoom_peripherals_init(void);
+extern void __init zoom_peripherals_init(void *);
Index: linux-omap-pm/arch/arm/mach-omap2/pm.h
===================================================================
--- linux-omap-pm.orig/arch/arm/mach-omap2/pm.h 2010-01-19 19:18:55.000000000 +0530
+++ linux-omap-pm/arch/arm/mach-omap2/pm.h 2010-01-19 19:19:23.000000000 +0530
@@ -41,9 +41,14 @@
#endif
struct prm_setup_vc {
- u16 clksetup;
- u16 voltsetup_time1;
- u16 voltsetup_time2;
+/* CLK SETUPTIME for RET & OFF */
+ u16 clksetup_ret;
+ u16 clksetup_off;
+/* VOLT SETUPTIME for RET & OFF */
+ u16 voltsetup_time1_ret;
+ u16 voltsetup_time2_ret;
+ u16 voltsetup_time1_off;
+ u16 voltsetup_time2_off;
u16 voltoffset;
u16 voltsetup2;
/* PRM_VC_CMD_VAL_0 specific bits */
Index: linux-omap-pm/arch/arm/mach-omap2/pm34xx.c
===================================================================
--- linux-omap-pm.orig/arch/arm/mach-omap2/pm34xx.c 2010-01-19 19:18:55.000000000 +0530
+++ linux-omap-pm/arch/arm/mach-omap2/pm34xx.c 2010-01-19 19:19:23.000000000 +0530
@@ -96,11 +96,17 @@
static struct powerdomain *cam_pwrdm;
static struct prm_setup_vc prm_setup = {
- .clksetup = 0xff,
- .voltsetup_time1 = 0xfff,
- .voltsetup_time2 = 0xfff,
+ /* CLK SETUPTIME for RET & OFF */
+ .clksetup_ret = 0xff,
+ .clksetup_off = 0xff,
+ /* VOLT SETUPTIME for RET & OFF */
+ .voltsetup_time1_ret = 0xfff,
+ .voltsetup_time2_ret = 0xfff,
+ .voltsetup_time1_off = 0xfff,
+ .voltsetup_time2_off = 0xfff,
.voltoffset = 0xff,
.voltsetup2 = 0xff,
+ /* VC COMMAND VALUES for VDD1/VDD2 */
.vdd0_on = 0x30, /* 1.2v */
.vdd0_onlp = 0x20, /* 1.0v */
.vdd0_ret = 0x1e, /* 0.975v */
@@ -374,6 +380,10 @@
int core_prev_state, per_prev_state;
u32 sdrc_pwr = 0;
int per_state_modified = 0;
+ u16 clksetup = 0xff;
+ u16 voltsetup_time1 = 0xfff;
+ u16 voltsetup_time2 = 0xfff;
+ u16 voltsetup2_sys_off = 0x0;
if (!_omap_sram_idle)
return;
@@ -438,20 +448,43 @@
omap_uart_prepare_idle(0);
omap_uart_prepare_idle(1);
if (core_next_state == PWRDM_POWER_OFF) {
+ /* VOLT & CLK SETUPTIME for OFF */
+ clksetup = prm_setup.clksetup_off;
+ voltsetup_time1 = prm_setup.voltsetup_time1_off;
+ voltsetup_time2 = prm_setup.voltsetup_time2_off;
+
u32 voltctrl = OMAP3430_AUTO_OFF;
- if (voltage_off_while_idle)
+ if (voltage_off_while_idle) {
voltctrl |= OMAP3430_SEL_OFF;
+ voltsetup2_sys_off = prm_setup.voltsetup2;
+ }
prm_set_mod_reg_bits(voltctrl,
OMAP3430_GR_MOD,
OMAP3_PRM_VOLTCTRL_OFFSET);
omap3_core_save_context();
omap3_prcm_save_context();
} else if (core_next_state == PWRDM_POWER_RET) {
+ /* VOLT & CLK SETUPTIME for RET */
+ clksetup = prm_setup.clksetup_ret;
+ voltsetup_time1 = prm_setup.voltsetup_time1_ret;
+ voltsetup_time2 = prm_setup.voltsetup_time2_ret;
+
prm_set_mod_reg_bits(OMAP3430_AUTO_RET,
OMAP3430_GR_MOD,
OMAP3_PRM_VOLTCTRL_OFFSET);
}
+ /* Write setup times */
+ prm_write_mod_reg(clksetup, OMAP3430_GR_MOD,
+ OMAP3_PRM_CLKSETUP_OFFSET);
+ prm_write_mod_reg((voltsetup_time2 <<
+ OMAP3430_SETUP_TIME2_SHIFT) |
+ (voltsetup_time1 <<
+ OMAP3430_SETUP_TIME1_SHIFT),
+ OMAP3430_GR_MOD, OMAP3_PRM_VOLTSETUP1_OFFSET);
+ prm_write_mod_reg(voltsetup2_sys_off, OMAP3430_GR_MOD,
+ OMAP3_PRM_VOLTSETUP2_OFFSET);
+
/* Enable IO-PAD and IO-CHAIN wakeups */
prm_set_mod_reg_bits(OMAP3430_EN_IO, WKUP_MOD, PM_WKEN);
omap3_enable_io_chain();
@@ -1077,12 +1110,17 @@
{
if (!setup_vc)
return;
-
- prm_setup.clksetup = setup_vc->clksetup;
- prm_setup.voltsetup_time1 = setup_vc->voltsetup_time1;
- prm_setup.voltsetup_time2 = setup_vc->voltsetup_time2;
+ /* CLK SETUPTIME for RET & OFF */
+ prm_setup.clksetup_ret = setup_vc->clksetup_ret;
+ prm_setup.clksetup_off = setup_vc->clksetup_off;
+ /* VOLT SETUPTIME for RET & OFF */
+ prm_setup.voltsetup_time1_ret = setup_vc->voltsetup_time1_ret;
+ prm_setup.voltsetup_time2_ret = setup_vc->voltsetup_time2_ret;
+ prm_setup.voltsetup_time1_off = setup_vc->voltsetup_time1_off;
+ prm_setup.voltsetup_time2_off = setup_vc->voltsetup_time2_off;
prm_setup.voltoffset = setup_vc->voltoffset;
prm_setup.voltsetup2 = setup_vc->voltsetup2;
+ /* VC COMMAND VALUES for VDD1/VDD2 */
prm_setup.vdd0_on = setup_vc->vdd0_on;
prm_setup.vdd0_onlp = setup_vc->vdd0_onlp;
prm_setup.vdd0_ret = setup_vc->vdd0_ret;
@@ -1259,11 +1297,11 @@
OMAP3_PRM_VC_I2C_CFG_OFFSET);
/* Write setup times */
- prm_write_mod_reg(prm_setup.clksetup, OMAP3430_GR_MOD,
+ prm_write_mod_reg(prm_setup.clksetup_ret, OMAP3430_GR_MOD,
OMAP3_PRM_CLKSETUP_OFFSET);
- prm_write_mod_reg((prm_setup.voltsetup_time2 <<
+ prm_write_mod_reg((prm_setup.voltsetup_time2_ret <<
OMAP3430_SETUP_TIME2_SHIFT) |
- (prm_setup.voltsetup_time1 <<
+ (prm_setup.voltsetup_time1_ret <<
OMAP3430_SETUP_TIME1_SHIFT),
OMAP3430_GR_MOD, OMAP3_PRM_VOLTSETUP1_OFFSET);
^ permalink raw reply [flat|nested] 2+ messages in thread* Re: [PATCH v2 2/6] omap3: pm: Using separate clk/volt setup_time for RET and OFF states
2010-01-19 17:35 [PATCH v2 2/6] omap3: pm: Using separate clk/volt setup_time for RET and OFF states x0080970
@ 2010-01-21 7:27 ` Nishanth Menon
0 siblings, 0 replies; 2+ messages in thread
From: Nishanth Menon @ 2010-01-21 7:27 UTC (permalink / raw)
To: Manuel, Lesly Arackal
Cc: linux-omap@vger.kernel.org, Derrick, David, Samuel Ortiz
Manuel, Lesly Arackal had written, on 01/19/2010 11:35 AM, the following:
> From: Lesly A M <x0080970@ti.com>
>
> omap3: pm: Using separate clk/volt setup_time for RET and OFF states
>
> Copied the setuptime in each board file, since OMAP3430 & OMAP3630
> has different voltage levels for the same states.
>
> Made the changes to program the setup time according to
> the target state of CORE power domain.
> The voltsetup2 is used only when the device exits sys_off mode
> (with PRM_VOLTCTRL[3]SEL_OFF set to 1).
>
> Signed-off-by: Lesly A M <x0080970@ti.com>
> Cc: Nishanth Menon <nm@ti.com>
> Cc: David Derrick <dderrick@ti.com>
> Cc: Samuel Ortiz <sameo@linux.intel.com>
>
> ---
> arch/arm/mach-omap2/board-3430sdp.c | 14 ++++--
> arch/arm/mach-omap2/board-3630sdp.c | 25 ++++++++++
> arch/arm/mach-omap2/board-zoom-peripherals.c | 4 +
> arch/arm/mach-omap2/board-zoom2.c | 25 ++++++++++
> arch/arm/mach-omap2/board-zoom3.c | 25 ++++++++++
> arch/arm/mach-omap2/include/mach/board-zoom.h | 2
> arch/arm/mach-omap2/pm.h | 11 +++-
> arch/arm/mach-omap2/pm34xx.c | 60 +++++++++++++++++++++-----
> 8 files changed, 143 insertions(+), 23 deletions(-)
>
> Index: linux-omap-pm/arch/arm/mach-omap2/board-3430sdp.c
> ===================================================================
> --- linux-omap-pm.orig/arch/arm/mach-omap2/board-3430sdp.c 2010-01-19 19:18:55.000000000 +0530
> +++ linux-omap-pm/arch/arm/mach-omap2/board-3430sdp.c 2010-01-19 19:19:23.000000000 +0530
> @@ -75,13 +75,19 @@
> {1, 10000, 30000, 300000},
> };
>
> -/* FIXME: These are not the optimal setup values to be used on 3430sdp*/
> +/* FIXME: These are not the optimal setup values to be used on 3430sdp */
> static struct prm_setup_vc omap3_setuptime_table = {
> - .clksetup = 0xff,
> - .voltsetup_time1 = 0xfff,
> - .voltsetup_time2 = 0xfff,
> + /* CLK SETUPTIME for RET & OFF */
> + .clksetup_ret = 0xff,
> + .clksetup_off = 0xff,
> + /* VOLT SETUPTIME for RET & OFF */
> + .voltsetup_time1_ret = 0xfff,
> + .voltsetup_time2_ret = 0xfff,
> + .voltsetup_time1_off = 0xfff,
> + .voltsetup_time2_off = 0xfff,
> .voltoffset = 0xff,
> .voltsetup2 = 0xff,
> + /* VC COMMAND VALUES for VDD1/VDD2 */
> .vdd0_on = 0x30,
> .vdd0_onlp = 0x20,
> .vdd0_ret = 0x1e,
> Index: linux-omap-pm/arch/arm/mach-omap2/board-3630sdp.c
> ===================================================================
> --- linux-omap-pm.orig/arch/arm/mach-omap2/board-3630sdp.c 2010-01-19 19:18:55.000000000 +0530
> +++ linux-omap-pm/arch/arm/mach-omap2/board-3630sdp.c 2010-01-19 19:19:23.000000000 +0530
> @@ -25,6 +25,29 @@
>
> #include "mux.h"
> #include "sdram-hynix-h8mbx00u0mer-0em.h"
> +#include "pm.h"
> +
> +static struct prm_setup_vc omap3_setuptime_table = {
> + /* CLK SETUPTIME for RET & OFF */
> + .clksetup_ret = 0xff,
> + .clksetup_off = 0xff,
> + /* VOLT SETUPTIME for RET & OFF */
> + .voltsetup_time1_ret = 0xfff,
> + .voltsetup_time2_ret = 0xfff,
> + .voltsetup_time1_off = 0xfff,
> + .voltsetup_time2_off = 0xfff,
> + .voltoffset = 0xff,
> + .voltsetup2 = 0xff,
> + /* VC COMMAND VALUES for VDD1/VDD2 */
> + .vdd0_on = 0x28, /* 1.1v */
> + .vdd0_onlp = 0x20, /* 1.0v */
> + .vdd0_ret = 0x13, /* 0.83v */
> + .vdd0_off = 0x00, /* 0.6v */
> + .vdd1_on = 0x2B, /* 1.1375v */
> + .vdd1_onlp = 0x20, /* 1.0v */
> + .vdd1_ret = 0x14, /* 0.85v */
> + .vdd1_off = 0x00, /* 0.6v */
> +};
>
> #if defined(CONFIG_SMC91X) || defined(CONFIG_SMC91X_MODULE)
>
> @@ -97,7 +120,7 @@
> static void __init omap_sdp_init(void)
> {
> omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
> - zoom_peripherals_init();
> + zoom_peripherals_init(&omap3_setuptime_table);
> board_smc91x_init();
> enable_board_wakeup_source();
> usb_ehci_init(&ehci_pdata);
> Index: linux-omap-pm/arch/arm/mach-omap2/board-zoom-peripherals.c
> ===================================================================
> --- linux-omap-pm.orig/arch/arm/mach-omap2/board-zoom-peripherals.c 2010-01-19 19:18:55.000000000 +0530
> +++ linux-omap-pm/arch/arm/mach-omap2/board-zoom-peripherals.c 2010-01-19 19:19:23.000000000 +0530
> @@ -26,6 +26,7 @@
>
> #include "mux.h"
> #include "mmc-twl4030.h"
> +#include "pm.h"
>
> /* Zoom2 has Qwerty keyboard*/
> static int board_keymap[] = {
> @@ -271,10 +272,11 @@
> OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP);
> }
>
> -void __init zoom_peripherals_init(void)
> +void __init zoom_peripherals_init(void *peripheral_data)
> {
> omap_i2c_init();
> omap_serial_init();
> usb_musb_init();
> enable_board_wakeup_source();
> + omap3_pm_init_vc((struct prm_setup_vc *)peripheral_data);
> }
> Index: linux-omap-pm/arch/arm/mach-omap2/board-zoom2.c
> ===================================================================
> --- linux-omap-pm.orig/arch/arm/mach-omap2/board-zoom2.c 2010-01-19 19:18:55.000000000 +0530
> +++ linux-omap-pm/arch/arm/mach-omap2/board-zoom2.c 2010-01-19 19:19:23.000000000 +0530
> @@ -26,6 +26,29 @@
> #include "mux.h"
> #include "sdram-micron-mt46h32m32lf-6.h"
> #include "omap3-opp.h"
> +#include "pm.h"
> +
> +static struct prm_setup_vc omap3_setuptime_table = {
> + /* CLK SETUPTIME for RET & OFF */
> + .clksetup_ret = 0xff,
> + .clksetup_off = 0xff,
> + /* VOLT SETUPTIME for RET & OFF */
> + .voltsetup_time1_ret = 0xfff,
> + .voltsetup_time2_ret = 0xfff,
> + .voltsetup_time1_off = 0xfff,
> + .voltsetup_time2_off = 0xfff,
I wonder if these values would change -> they seem to be 0xffff thru out
the patch.
> + .voltoffset = 0xff,
> + .voltsetup2 = 0xff,
> + /* VC COMMAND VALUES for VDD1/VDD2 */
> + .vdd0_on = 0x30,
> + .vdd0_onlp = 0x20,
> + .vdd0_ret = 0x1e,
> + .vdd0_off = 0x00,
> + .vdd1_on = 0x2c,
> + .vdd1_onlp = 0x20,
> + .vdd1_ret = 0x1e,
> + .vdd1_off = 0x00,
> +};
>
> static void __init omap_zoom2_init_irq(void)
> {
> @@ -82,7 +105,7 @@
> static void __init omap_zoom2_init(void)
> {
> omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
> - zoom_peripherals_init();
> + zoom_peripherals_init(&omap3_setuptime_table);
> zoom_debugboard_init();
> }
>
> Index: linux-omap-pm/arch/arm/mach-omap2/board-zoom3.c
> ===================================================================
> --- linux-omap-pm.orig/arch/arm/mach-omap2/board-zoom3.c 2010-01-19 19:18:55.000000000 +0530
> +++ linux-omap-pm/arch/arm/mach-omap2/board-zoom3.c 2010-01-19 19:19:23.000000000 +0530
> @@ -24,6 +24,29 @@
>
> #include "mux.h"
> #include "sdram-hynix-h8mbx00u0mer-0em.h"
> +#include "pm.h"
> +
> +static struct prm_setup_vc omap3_setuptime_table = {
> + /* CLK SETUPTIME for RET & OFF */
> + .clksetup_ret = 0xff,
> + .clksetup_off = 0xff,
> + /* VOLT SETUPTIME for RET & OFF */
> + .voltsetup_time1_ret = 0xfff,
> + .voltsetup_time2_ret = 0xfff,
> + .voltsetup_time1_off = 0xfff,
> + .voltsetup_time2_off = 0xfff,
> + .voltoffset = 0xff,
> + .voltsetup2 = 0xff,
> + /* VC COMMAND VALUES for VDD1/VDD2 */
> + .vdd0_on = 0x28, /* 1.1v */
> + .vdd0_onlp = 0x20, /* 1.0v */
> + .vdd0_ret = 0x13, /* 0.83v */
> + .vdd0_off = 0x00, /* 0.6v */
> + .vdd1_on = 0x2B, /* 1.1375v */
> + .vdd1_onlp = 0x20, /* 1.0v */
> + .vdd1_ret = 0x14, /* 0.85v */
> + .vdd1_off = 0x00, /* 0.6v */
> +};
>
> static void __init omap_zoom_map_io(void)
> {
> @@ -66,7 +89,7 @@
> static void __init omap_zoom_init(void)
> {
> omap3_mux_init(board_mux, OMAP_PACKAGE_CBP);
> - zoom_peripherals_init();
> + zoom_peripherals_init(&omap3_setuptime_table);
> zoom_debugboard_init();
>
> omap_mux_init_gpio(64, OMAP_PIN_OUTPUT);
> Index: linux-omap-pm/arch/arm/mach-omap2/include/mach/board-zoom.h
> ===================================================================
> --- linux-omap-pm.orig/arch/arm/mach-omap2/include/mach/board-zoom.h 2010-01-19 19:18:55.000000000 +0530
> +++ linux-omap-pm/arch/arm/mach-omap2/include/mach/board-zoom.h 2010-01-19 19:19:23.000000000 +0530
> @@ -2,4 +2,4 @@
> * Defines for zoom boards
> */
> extern int __init zoom_debugboard_init(void);
> -extern void __init zoom_peripherals_init(void);
> +extern void __init zoom_peripherals_init(void *);
> Index: linux-omap-pm/arch/arm/mach-omap2/pm.h
> ===================================================================
> --- linux-omap-pm.orig/arch/arm/mach-omap2/pm.h 2010-01-19 19:18:55.000000000 +0530
> +++ linux-omap-pm/arch/arm/mach-omap2/pm.h 2010-01-19 19:19:23.000000000 +0530
> @@ -41,9 +41,14 @@
> #endif
>
> struct prm_setup_vc {
> - u16 clksetup;
> - u16 voltsetup_time1;
> - u16 voltsetup_time2;
> +/* CLK SETUPTIME for RET & OFF */
> + u16 clksetup_ret;
> + u16 clksetup_off;
> +/* VOLT SETUPTIME for RET & OFF */
> + u16 voltsetup_time1_ret;
> + u16 voltsetup_time2_ret;
> + u16 voltsetup_time1_off;
> + u16 voltsetup_time2_off;
> u16 voltoffset;
> u16 voltsetup2;
could i recommend the following instead of duplicating every variable twice?
introduce a struct which is common for ret and off modes? that makes it
easier for the later code ->
voltsetup_time1
voltsetup_time2
clksetup
then in prm_setup_vc {
struct something ret;
struct something off;
}
in your code below,
if (core_next_state == PWRDM_POWER_OFF)
memcpy(&some_var, prm_setup.off, sizeof(struct something);
else if (core_next_state == PWRDM_POWER_RET)
memcpy(&some_var, prm_setup.ret, sizeof(struct something);
makes code less confusing to dig thru.
> /* PRM_VC_CMD_VAL_0 specific bits */
> Index: linux-omap-pm/arch/arm/mach-omap2/pm34xx.c
> ===================================================================
> --- linux-omap-pm.orig/arch/arm/mach-omap2/pm34xx.c 2010-01-19 19:18:55.000000000 +0530
> +++ linux-omap-pm/arch/arm/mach-omap2/pm34xx.c 2010-01-19 19:19:23.000000000 +0530
> @@ -96,11 +96,17 @@
> static struct powerdomain *cam_pwrdm;
>
> static struct prm_setup_vc prm_setup = {
> - .clksetup = 0xff,
> - .voltsetup_time1 = 0xfff,
> - .voltsetup_time2 = 0xfff,
> + /* CLK SETUPTIME for RET & OFF */
> + .clksetup_ret = 0xff,
> + .clksetup_off = 0xff,
> + /* VOLT SETUPTIME for RET & OFF */
> + .voltsetup_time1_ret = 0xfff,
> + .voltsetup_time2_ret = 0xfff,
> + .voltsetup_time1_off = 0xfff,
> + .voltsetup_time2_off = 0xfff,
> .voltoffset = 0xff,
> .voltsetup2 = 0xff,
> + /* VC COMMAND VALUES for VDD1/VDD2 */
> .vdd0_on = 0x30, /* 1.2v */
> .vdd0_onlp = 0x20, /* 1.0v */
> .vdd0_ret = 0x1e, /* 0.975v */
> @@ -374,6 +380,10 @@
> int core_prev_state, per_prev_state;
> u32 sdrc_pwr = 0;
> int per_state_modified = 0;
> + u16 clksetup = 0xff;
> + u16 voltsetup_time1 = 0xfff;
> + u16 voltsetup_time2 = 0xfff;
> + u16 voltsetup2_sys_off = 0x0;
>
> if (!_omap_sram_idle)
> return;
> @@ -438,20 +448,43 @@
> omap_uart_prepare_idle(0);
> omap_uart_prepare_idle(1);
> if (core_next_state == PWRDM_POWER_OFF) {
> + /* VOLT & CLK SETUPTIME for OFF */
> + clksetup = prm_setup.clksetup_off;
> + voltsetup_time1 = prm_setup.voltsetup_time1_off;
> + voltsetup_time2 = prm_setup.voltsetup_time2_off;
> +
> u32 voltctrl = OMAP3430_AUTO_OFF;
variable declaration after code?
>
> - if (voltage_off_while_idle)
> + if (voltage_off_while_idle) {
> voltctrl |= OMAP3430_SEL_OFF;
> + voltsetup2_sys_off = prm_setup.voltsetup2;
> + }
> prm_set_mod_reg_bits(voltctrl,
> OMAP3430_GR_MOD,
> OMAP3_PRM_VOLTCTRL_OFFSET);
> omap3_core_save_context();
> omap3_prcm_save_context();
do you want to piggyback or move the above two lines away from this
logic? it might be better to keep this context of if else to prm setup
times, while the decision to save prcm/core contexts could go in a
seperate if condition and allow the compiler optimization to do whatever
magic of it's own..
> } else if (core_next_state == PWRDM_POWER_RET) {
> + /* VOLT & CLK SETUPTIME for RET */
> + clksetup = prm_setup.clksetup_ret;
> + voltsetup_time1 = prm_setup.voltsetup_time1_ret;
> + voltsetup_time2 = prm_setup.voltsetup_time2_ret;
> +
> prm_set_mod_reg_bits(OMAP3430_AUTO_RET,
> OMAP3430_GR_MOD,
> OMAP3_PRM_VOLTCTRL_OFFSET);
> }
> + /* Write setup times */
> + prm_write_mod_reg(clksetup, OMAP3430_GR_MOD,
> + OMAP3_PRM_CLKSETUP_OFFSET);
> + prm_write_mod_reg((voltsetup_time2 <<
> + OMAP3430_SETUP_TIME2_SHIFT) |
> + (voltsetup_time1 <<
> + OMAP3430_SETUP_TIME1_SHIFT),
> + OMAP3430_GR_MOD, OMAP3_PRM_VOLTSETUP1_OFFSET);
> + prm_write_mod_reg(voltsetup2_sys_off, OMAP3430_GR_MOD,
> + OMAP3_PRM_VOLTSETUP2_OFFSET);
> +
> /* Enable IO-PAD and IO-CHAIN wakeups */
> prm_set_mod_reg_bits(OMAP3430_EN_IO, WKUP_MOD, PM_WKEN);
> omap3_enable_io_chain();
> @@ -1077,12 +1110,17 @@
> {
> if (!setup_vc)
> return;
> -
> - prm_setup.clksetup = setup_vc->clksetup;
> - prm_setup.voltsetup_time1 = setup_vc->voltsetup_time1;
> - prm_setup.voltsetup_time2 = setup_vc->voltsetup_time2;
> + /* CLK SETUPTIME for RET & OFF */
> + prm_setup.clksetup_ret = setup_vc->clksetup_ret;
> + prm_setup.clksetup_off = setup_vc->clksetup_off;
> + /* VOLT SETUPTIME for RET & OFF */
> + prm_setup.voltsetup_time1_ret = setup_vc->voltsetup_time1_ret;
> + prm_setup.voltsetup_time2_ret = setup_vc->voltsetup_time2_ret;
> + prm_setup.voltsetup_time1_off = setup_vc->voltsetup_time1_off;
> + prm_setup.voltsetup_time2_off = setup_vc->voltsetup_time2_off;
> prm_setup.voltoffset = setup_vc->voltoffset;
> prm_setup.voltsetup2 = setup_vc->voltsetup2;
> + /* VC COMMAND VALUES for VDD1/VDD2 */
> prm_setup.vdd0_on = setup_vc->vdd0_on;
> prm_setup.vdd0_onlp = setup_vc->vdd0_onlp;
> prm_setup.vdd0_ret = setup_vc->vdd0_ret;
these get the same comments -> what exactly is vdd0 btw?
> @@ -1259,11 +1297,11 @@
> OMAP3_PRM_VC_I2C_CFG_OFFSET);
>
> /* Write setup times */
> - prm_write_mod_reg(prm_setup.clksetup, OMAP3430_GR_MOD,
> + prm_write_mod_reg(prm_setup.clksetup_ret, OMAP3430_GR_MOD,
> OMAP3_PRM_CLKSETUP_OFFSET);
> - prm_write_mod_reg((prm_setup.voltsetup_time2 <<
> + prm_write_mod_reg((prm_setup.voltsetup_time2_ret <<
> OMAP3430_SETUP_TIME2_SHIFT) |
> - (prm_setup.voltsetup_time1 <<
> + (prm_setup.voltsetup_time1_ret <<
> OMAP3430_SETUP_TIME1_SHIFT),
> OMAP3430_GR_MOD, OMAP3_PRM_VOLTSETUP1_OFFSET);
>
--
Regards,
Nishanth Menon
^ permalink raw reply [flat|nested] 2+ messages in thread
end of thread, other threads:[~2010-01-21 7:27 UTC | newest]
Thread overview: 2+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2010-01-19 17:35 [PATCH v2 2/6] omap3: pm: Using separate clk/volt setup_time for RET and OFF states x0080970
2010-01-21 7:27 ` Nishanth Menon
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox