Re: [PATCH V2 0/10] omap_hsmmc changes V2

[Adrian Hunter <adrian.hunter@nokia.com>]

Madhusudhan wrote:
> 
>> -----Original Message-----
>> From: Adrian Hunter [mailto:adrian.hunter@nokia.com]
>> Sent: Saturday, January 16, 2010 7:33 PM
>> To: Tony Lindgren
>> Cc: Adrian Hunter; Madhusudhan Chikkature; Paul Walmsley; linux-omap
>> Mailing List; linux-mmc Mailing List; Andrew Morton
>> Subject: [PATCH V2 0/10] omap_hsmmc changes V2
>>
>> Hi
>>
>> Here are some changes we need for omap_hsmmc.  They are dependent on OMAP
>> board files so it would be simplest if the patches all went via the OMAP
>> tree.
>>
>> This is version 2 of this patch set.  Thank you Tony, Paul and Madhu for
>> your comments.
>>
>> Changes from version 1:
>> 	- amended patch 'omap_hsmmc: Move gpio and regulator control from
>> 	board file' so that system control functions remain in the board
>> 	file
>> 	- for clarity, split patch 'omap: Rename mmc-twl4030 to hsmmc' into
>> 	'omap: Rename mmc-twl4030 files to hsmmc' and
>> 	'omap: Rename hsmmc symbols to reflect independence from twl4030'
>> 	- removed patch 'omap_hsmmc: set DVFS/PM constraints'
>> 	- added patch 'omap: Add functions for dynamic remuxing of pins'
>> 	- renamed and reworked patch 'omap: RX51: Remux to pull eMMC lines
>> 	down when powering off' (was 'omap_hsmmc: RX51: set padconfs to pull
>> 	down when powering off eMMC')
>> 	- added patch 'omap_hsmmc: Ensure regulator enable / disable are
>> 	paired'
>> 	- fixed mistakes in patch 'omap_hsmmc: Allow for a shared VccQ'
>>
> Reviewed the omap_hsmmc changes and did a sanity test on Zoom2.
> Acked-by: Madhusudhan Chikkature <madhu.cr@ti.com>
> 
> Regards,
> Madhu

Thanks Madhu.  Tony, are you ok taking these patches into your tree?

>> Adrian Hunter (9):
>>       omap_hsmmc: Move gpio and regulator control from board file
>>       omap: Rename mmc-twl4030 files to hsmmc
>>       omap: Rename hsmmc symbols to reflect independence from twl4030
>>       omap: Reconnect hsmmc context loss count
>>       omap: RX51: Remux to pull eMMC lines down when powering off
>>       omap_hsmmc: Allow for power saving without going off
>>       omap_hsmmc: Fix disable timeouts
>>       omap_hsmmc: Ensure regulator enable / disable are paired
>>       omap_hsmmc: Allow for a shared VccQ
>>
>> Tony Lindgren (1):
>>       omap: Add functions for dynamic remuxing of pins
>>
>>  arch/arm/configs/rx51_defconfig                |    4 +-
>>  arch/arm/mach-omap2/Makefile                   |   28 +-
>>  arch/arm/mach-omap2/board-2430sdp.c            |    6 +-
>>  arch/arm/mach-omap2/board-3430sdp.c            |    6 +-
>>  arch/arm/mach-omap2/board-cm-t35.c             |    6 +-
>>  arch/arm/mach-omap2/board-igep0020.c           |    6 +-
>>  arch/arm/mach-omap2/board-ldp.c                |    6 +-
>>  arch/arm/mach-omap2/board-omap3beagle.c        |    6 +-
>>  arch/arm/mach-omap2/board-omap3evm.c           |    6 +-
>>  arch/arm/mach-omap2/board-omap3pandora.c       |    6 +-
>>  arch/arm/mach-omap2/board-omap3touchbook.c     |    6 +-
>>  arch/arm/mach-omap2/board-overo.c              |    6 +-
>>  arch/arm/mach-omap2/board-rx51-peripherals.c   |   63 +++-
>>  arch/arm/mach-omap2/board-zoom-peripherals.c   |    6 +-
>>  arch/arm/mach-omap2/hsmmc.c                    |  261 ++++++++++++
>>  arch/arm/mach-omap2/{mmc-twl4030.h => hsmmc.h} |   14 +-
>>  arch/arm/mach-omap2/mmc-twl4030.c              |  537 -------------------
>> -----
>>  arch/arm/mach-omap2/mux.c                      |   22 +-
>>  arch/arm/mach-omap2/mux.h                      |   24 +
>>  arch/arm/plat-omap/include/plat/mmc.h          |   35 ++-
>>  drivers/mmc/host/omap_hsmmc.c                  |  375 ++++++++++++++++-
>>  21 files changed, 788 insertions(+), 641 deletions(-)
>>  create mode 100644 arch/arm/mach-omap2/hsmmc.c
>>  rename arch/arm/mach-omap2/{mmc-twl4030.h => hsmmc.h} (63%)
>>  delete mode 100644 arch/arm/mach-omap2/mmc-twl4030.c
>>
>>
>>
>> Regards
>> Adrian
> 
> 
>