From: Igor Grinberg <grinberg@compulab.co.il>
To: linux-omap@vger.kernel.org
Subject: AM3517 (Sitara) MMC2 help
Date: Tue, 24 Aug 2010 15:42:04 +0300 [thread overview]
Message-ID: <4C73BE1C.7080503@compulab.co.il> (raw)
Hi,
I have am3517 based board and Libertas sdio (4 wires)
wifi connected directly (no transceiver / level shifter) on mmc2
(which is named mmc1 in s/w).
am3517 is configured (h/w) for 3.3V and so is Libertas wifi.
dmesg | grep mmc1 shows:
--------------cut------------------
mux: Setting signal sdmmc1_clk.sdmmc1_clk 0x0000 -> 0x0118
mux: Setting signal sdmmc1_cmd.sdmmc1_cmd 0x0000 -> 0x0118
mux: Setting signal sdmmc1_dat0.sdmmc1_dat0 0x0100 -> 0x0118
mux: Setting signal sdmmc1_dat1.sdmmc1_dat1 0x0100 -> 0x0118
mux: Setting signal sdmmc1_dat2.sdmmc1_dat2 0x0100 -> 0x0118
mux: Setting signal sdmmc1_dat3.sdmmc1_dat3 0x0100 -> 0x0118
mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
mmc1: clock 0Hz busmode 1 powermode 1 cs 0 Vdd 20 width 0 timing 0
mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0
mmc1: starting CMD52 arg 00000c00 flags 00000195
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD52, argument 0x00000c00
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD52 arg 80000c08 flags 00000195
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD52, argument 0x80000c08
mmc1: req done (CMD52): -110: 00000000 00000000 00000000 00000000
mmc1: clock 400000Hz busmode 1 powermode 2 cs 1 Vdd 20 width 0 timing 0
mmc1: starting CMD0 arg 00000000 flags 000000c0
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD0, argument 0x00000000
mmc1: req done (CMD0): 0: 00000000 00000000 00000000 00000000
mmc1: clock 400000Hz busmode 1 powermode 2 cs 0 Vdd 20 width 0 timing 0
mmc1: starting CMD8 arg 000001aa flags 000002f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD8, argument 0x000001aa
mmc1: req done (CMD8): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD5 arg 00000000 flags 000002e1
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000
mmc1: req failed (CMD5): -110, retrying...
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000
mmc1: req failed (CMD5): -110, retrying...
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000
mmc1: req failed (CMD5): -110, retrying...
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD5, argument 0x00000000
mmc1: req done (CMD5): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD55 arg 00000000 flags 000000f5
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD55, argument 0x00000000
mmc1: req done (CMD55): -110: 00000000 00000000 00000000 00000000
mmc1: starting CMD1 arg 00000000 flags 000000e1
mmci-omap-hs mmci-omap-hs.1: mmc1: CMD1, argument 0x00000000
mmc1: req done (CMD1): -110: 00000000 00000000 00000000 00000000
mmc1: clock 0Hz busmode 1 powermode 0 cs 0 Vdd 0 width 0 timing 0
-------------------cut---------------------
Libertas is powered up and gets reseted properly.
On the oscilloscope, I see some communication going
on the CMD line and stops after some time.
am3517 PSP from TI, does not even registers/enables
the wifi combo found on am3517evm.
Have anybody got the mmc2 working on am3517?
May be with transceiver?
Any help will be appreciated.
Thanks
--
Regards,
Igor.
next reply other threads:[~2010-08-24 12:42 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-08-24 12:42 Igor Grinberg [this message]
2010-08-25 0:29 ` AM3517 (Sitara) MMC2 help Laine Walker-Avina
2010-08-25 0:36 ` Laine Walker-Avina
2010-08-25 7:57 ` Igor Grinberg
2010-08-25 8:12 ` Igor Grinberg
2010-08-25 9:26 ` Igor Grinberg
2010-08-25 13:46 ` Ashwin Bihari
2010-08-25 13:51 ` Gadiyar, Anand
2010-08-25 13:58 ` Ashwin Bihari
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4C73BE1C.7080503@compulab.co.il \
--to=grinberg@compulab.co.il \
--cc=linux-omap@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox