From: Anand Gadiyar <gadiyar@ti.com>
To: Ming Lei <tom.leiming@gmail.com>
Cc: Benoit Cousson <b-cousson@ti.com>,
Stephen Rothwell <sfr@canb.auug.org.au>,
Paul Walmsley <paul@pwsan.com>, Greg KH <greg@kroah.com>,
linux-next@vger.kernel.org, linux-kernel@vger.kernel.org,
Felipe Balbi <balbi@ti.com>, Tony Lindgren <tony@atomide.com>,
linux-omap@vger.kernel.org
Subject: Re: linux-next: manual merge of the usb tree with the omap tree
Date: Fri, 07 Jan 2011 19:37:10 +0530 [thread overview]
Message-ID: <4D271E0E.8050401@ti.com> (raw)
In-Reply-To: <AANLkTimzQ1PHN986fqPF0yjd1M+390nSUDYJ65pu0z_f@mail.gmail.com>
On 1/6/2011 9:20 PM, Ming Lei wrote:
> Hi,
>
> 2011/1/6 Ming Lei <tom.leiming@gmail.com>:
>> Hi,
>>
>> 2011/1/6 Anand Gadiyar <gadiyar@ti.com>:
>>
>>> I'll take a look in a short while. I don't have an XM to
>>> test, so you'll have to help me out here.
>>
>> No problem for me, :-)
>
> I see why the beagle xM does not work, the attachment patch is
> needed to make it working.
>
> But the ehci on panda(omap4430) still does not work with
> 2.6.37-next-20110106+, and follows the failure messages:
>
> [ 46.572601] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 46.580017] ehci_hcd: block sizes: qh 60 qtd 96 itd 160 sitd 96
> [ 46.580078] bus: 'platform': add driver ehci-omap
> [ 46.580139] bus: 'platform': driver_probe_device: matched device ehci-omap.0 with driver ehci-omap
> [ 46.580169] bus: 'platform': really_probe: probing driver ehci-omap with device ehci-omap.0
> [ 46.580200] ehci-omap ehci-omap.0: failed to get ehci port0 regulator
> [ 46.580200] ehci-omap ehci-omap.0: starting TI EHCI USB Controller
> [ 46.580291] ehci-omap ehci-omap.0: OMAP UHH_REVISION 0x50700100
> [ 46.580352] ehci-omap ehci-omap.0: TLL RESET DONE
> [ 46.580352] ehci-omap ehci-omap.0: UHH setup done, uhh_hostconfig=1c
> [ 46.580383] ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3
> [ 46.580383] ehci-omap ehci-omap.0: reset hcc_params 20016 thresh 1 uframes 256/512/1024 park LPM
> [ 46.580383] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> [ 46.588592] drivers/usb/core/inode.c: creating file 'devices'
> [ 46.588623] drivers/usb/core/inode.c: creating file '001'
> [ 46.588684] device: 'usbmon1': device_add
> [ 46.588867] PM: Adding info for No Bus:usbmon1
> [ 46.590026] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
> [ 46.645721] ehci-omap ehci-omap.0: park 0
> [ 46.645721] ehci-omap ehci-omap.0: support lpm
> [ 46.645751] ehci-omap ehci-omap.0: irq 109, io mem 0x4a064c00
> [ 46.651763] ehci-omap ehci-omap.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
> [ 46.651763] ehci-omap ehci-omap.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
> [ 46.661254] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> [ 46.667297] usb usb1: rpm_resume flags 0x0
> [ 46.667297] usb usb1: rpm_resume returns 1
> [ 46.667358] usb usb1: default language 0x0409
> [ 46.667358] usb usb1: udev 1, busnum 1, minor = 0
> [ 46.667388] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 46.675476] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 46.683288] usb usb1: Product: OMAP-EHCI Host Controller
> [ 46.689086] usb usb1: Manufacturer: Linux 2.6.37-next-20110106+ ehci_hcd
> [ 46.696350] usb usb1: SerialNumber: ehci-omap.0
> [ 46.701354] device: 'usb1': device_add
> [ 46.701568] bus: 'usb': add device usb1
> [ 46.701629] PM: Adding info for usb:usb1
> [ 46.702758] bus: 'usb': driver_probe_device: matched device usb1 with driver usb
> [ 46.702758] bus: 'usb': really_probe: probing driver usb with device usb1
> [ 46.702819] usb usb1: usb_probe_device
> [ 46.702819] usb usb1: configuration #1 chosen from 1 choice
> [ 46.702850] usb usb1: rpm_resume flags 0x4
> [ 46.702850] usb usb1: rpm_resume returns 1
> [ 46.702911] usb usb1: adding 1-0:1.0 (config #1, interface 0)
> [ 46.702911] device: '1-0:1.0': device_add
> [ 46.702941] bus: 'usb': add device 1-0:1.0
> [ 46.703002] PM: Adding info for usb:1-0:1.0
> [ 46.703430] bus: 'usb': driver_probe_device: matched device 1-0:1.0 with driver hub
> [ 46.703460] bus: 'usb': really_probe: probing driver hub with device 1-0:1.0
> [ 46.703460] hub 1-0:1.0: usb_probe_interface
> [ 46.703491] hub 1-0:1.0: usb_probe_interface - got id
> [ 46.703491] usb usb1: rpm_resume flags 0x4
> [ 46.703491] usb usb1: rpm_resume returns 1
> [ 46.703521] hub 1-0:1.0: USB hub found
> [ 46.707427] hub 1-0:1.0: 3 ports detected
> [ 46.715698] hub 1-0:1.0: standalone hub
> [ 46.715698] hub 1-0:1.0: individual port power switching
> [ 46.715728] hub 1-0:1.0: individual port over-current protection
> [ 46.715728] hub 1-0:1.0: power on to power good time: 20ms
> [ 46.715759] hub 1-0:1.0: local power source is good
> [ 46.715759] hub 1-0:1.0: enabling power on all ports
> [ 46.715820] driver: '1-0:1.0': driver_bound: bound to device 'hub'
> [ 46.715820] bus: 'usb': really_probe: bound device 1-0:1.0 to driver hub
> [ 46.715850] device: 'ep_81': device_add
> [ 46.717468] PM: Adding info for No Bus:ep_81
> [ 46.717498] device: 'usbdev1.1': device_add
> [ 46.717590] PM: Adding info for No Bus:usbdev1.1
> [ 46.717773] drivers/usb/core/inode.c: creating file '001'
> [ 46.717803] driver: 'usb1': driver_bound: bound to device 'usb'
> [ 46.717803] bus: 'usb': really_probe: bound device usb1 to driver usb
> [ 46.717834] device: 'ep_00': device_add
> [ 46.717895] PM: Adding info for No Bus:ep_00
> [ 46.717895] usb usb1: rpm_suspend flags 0xc
> [ 46.717926] usb usb1: rpm_suspend returns -16
> [ 46.717926] ehci-omap ehci-omap.0: ...powerup ports...
> [ 46.747161] driver: 'ehci-omap.0': driver_bound: bound to device 'ehci-omap'
> [ 46.747192] bus: 'platform': really_probe: bound device ehci-omap.0 to driver ehci-omap
> [ 46.809661] ehci-omap ehci-omap.0: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT
> [ 46.809692] hub 1-0:1.0: port 1: status 0501 change 0001
> [ 46.911193] hub 1-0:1.0: state 7 ports 3 chg 0002 evt 0000
> [ 46.911193] hub 1-0:1.0: rpm_resume flags 0x4
> [ 46.911193] hub 1-0:1.0: rpm_resume returns 1
> [ 46.911224] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
> [ 46.973907] ehci-omap ehci-omap.0: port 1 high speed
> [ 46.973907] ehci-omap ehci-omap.0: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
> [ 47.036102] usb 1-1: new high speed USB device using ehci-omap and address 2
> [ 47.044036] ehci-omap ehci-omap.0: detected XactErr len 0/8 retry 1
> [ 47.044158] ehci-omap ehci-omap.0: detected XactErr len 0/8 retry 2
> [ 47.044281] ehci-omap ehci-omap.0: detected XactErr len 0/8 retry 3
> [ 47.044403] ehci-omap ehci-omap.0: detected XactErr len 0/8 retry 4
> [ 47.044525] ehci-omap ehci-omap.0: detected XactErr len 0/8 retry 5
> [ 47.044647] ehci-omap ehci-omap.0: detected XactErr len 0/8 retry 6
> [ 47.044799] ehci-omap ehci-omap.0: detected XactErr len 0/8 retry 7
> [ 47.044921] ehci-omap ehci-omap.0: detected XactErr len 0/8 retry 8
> ......
>
> Anand, could you help to check it?
>
Hi Ming Lei,
I'm able to reproduce this on my panda, and I have it working as of
linux-next-20101221 (the last version I tested last year) and failing
on linux-next-20101227 (which was the very next linux-next release).
Not sure why, but my Panda manages to get the VID:PID of the hub as
well, while yours does not even get there.
I may need a few more hours to debug this, unless someone beats me
to it. ;)
- Anand
next prev parent reply other threads:[~2011-01-07 14:07 UTC|newest]
Thread overview: 38+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-12-23 6:18 linux-next: manual merge of the usb tree with the omap tree Stephen Rothwell
2010-12-23 8:36 ` Felipe Balbi
2010-12-23 18:29 ` Cousson, Benoit
2011-01-06 15:02 ` Ming Lei
2011-01-06 15:07 ` Anand Gadiyar
2011-01-06 15:25 ` Ming Lei
2011-01-06 15:50 ` Ming Lei
2011-01-07 14:07 ` Anand Gadiyar [this message]
2011-01-07 14:15 ` Ming Lei
2011-01-07 14:39 ` Anand Gadiyar
2011-01-07 15:20 ` Anand Gadiyar
2011-01-07 18:54 ` Gadiyar, Anand
2011-01-07 19:24 ` Felipe Balbi
2011-01-10 13:53 ` Ming Lei
2011-01-10 14:09 ` Anand Gadiyar
2011-01-06 15:43 ` Brad Parker
2011-01-06 16:59 ` Koen Kooi
2011-01-06 17:57 ` Nishanth Menon
2011-01-06 18:15 ` Kevin Hilman
2011-01-06 18:21 ` Nishanth Menon
2011-01-06 18:38 ` Kevin Hilman
2011-01-06 20:24 ` Nishanth Menon
2011-01-06 21:29 ` Kevin Hilman
2011-01-06 18:27 ` Paul Walmsley
-- strict thread matches above, loose matches on Subject: below --
2011-03-02 5:58 Stephen Rothwell
2011-03-02 5:58 Stephen Rothwell
2011-03-02 5:57 Stephen Rothwell
2011-03-03 8:48 ` Felipe Balbi
2011-03-03 16:02 ` Greg KH
2011-03-03 17:39 ` Felipe Balbi
2011-03-02 5:57 Stephen Rothwell
2011-03-02 8:23 ` Felipe Balbi
2011-03-02 14:23 ` Greg KH
2011-03-03 8:18 ` Felipe Balbi
2009-11-11 8:30 Stephen Rothwell
2009-11-11 19:12 ` Tony Lindgren
2009-11-11 19:20 ` Tony Lindgren
2009-11-11 21:52 ` Stephen Rothwell
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4D271E0E.8050401@ti.com \
--to=gadiyar@ti.com \
--cc=b-cousson@ti.com \
--cc=balbi@ti.com \
--cc=greg@kroah.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-next@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=paul@pwsan.com \
--cc=sfr@canb.auug.org.au \
--cc=tom.leiming@gmail.com \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox