* Issue with DSS DSI: Complex IO not powering on
@ 2011-04-06 1:55 Juha Kuikka
2011-04-06 6:16 ` Archit Taneja
0 siblings, 1 reply; 4+ messages in thread
From: Juha Kuikka @ 2011-04-06 1:55 UTC (permalink / raw)
To: linux-omap@vger.kernel.org Mailing List
Hi,
I am working on a custom board with DM3730 and a DSI panel and I have
a problem in powering on the DSI complex IO block.
The DSS DSI initialization fails with:
omapdss DSI: dsi_complexio_init
omapdss DSI error: complexio reset not done! <-- my own addition
omapdss DSI error: failed to set complexio power state to 1
The DSI PLL is used and configured according to the example values in
the TRM (not proper for our panel but they should enable the complex
IO to at least power on, right).
Output form DSS DEBUG:
omapdss DSI: LP_CLK_DIV 6, LP_CLK 7500000
omapdss DISPC: lck = 90000000 (1)
omapdss DISPC: pck = 30000000 (3)
- DSI PLL -
dsi pll source = dss2_alwon_fclk
Fint 2000000 regn 13
CLKIN4DDR 1080000000 regm 270
dsi1_pll_fck 90000000 regm3 12 (on)
dsi2_pll_fck 90000000 regm4 12 (on)
- DSI -
dsi fclk source = dsi2_pll_fclk
DSI_FCLK 90000000
DDR_CLK 270000000
TxByteClkHS 67500000
LP_CLK 7500000
VP_CLK 90000000
VP_PCLK 30000000
As far as I can tell these values fill all the requirements set in the
TRM for clock rates and their ratios.
After the fail in dsi_complexio_init I dump all registers:
DSI_REVISION 00000010
DSI_SYSCONFIG 00000011
DSI_SYSSTATUS 00000001
DSI_IRQSTATUS 00080080
DSI_IRQENABLE 00000000
DSI_CTRL 00000100
DSI_COMPLEXIO_CFG1 48200321
DSI_COMPLEXIO_IRQ_STATUS 00000000
DSI_COMPLEXIO_IRQ_ENABLE 00000000
DSI_CLK_CTRL a0304006
DSI_TIMING1 7fff7fff
DSI_TIMING2 7fff7fff
DSI_VM_TIMING1 00000000
DSI_VM_TIMING2 00000000
DSI_VM_TIMING3 00000000
DSI_CLK_TIMING 00000101
DSI_TX_FIFO_VC_SIZE 00000000
DSI_RX_FIFO_VC_SIZE 00000000
DSI_COMPLEXIO_CFG2 00000000
DSI_RX_FIFO_VC_FULLNESS 00000000
DSI_VM_TIMING4 00000000
DSI_TX_FIFO_VC_EMPTINESS 00000000
DSI_VM_TIMING5 00000000
DSI_VM_TIMING6 00000000
DSI_VM_TIMING7 00000000
DSI_STOPCLK_TIMING 00000080
DSI_VC_CTRL(0) 00000000
DSI_VC_TE(0) 00000000
DSI_VC_LONG_PACKET_HEADER(0) 00000000
DSI_VC_LONG_PACKET_PAYLOAD(0) 00000000
DSI_VC_SHORT_PACKET_HEADER(0) 00000000
DSI_VC_IRQSTATUS(0) 00000000
DSI_VC_IRQENABLE(0) 00000000
DSI_VC_CTRL(1) 00000000
DSI_VC_TE(1) 00000000
DSI_VC_LONG_PACKET_HEADER(1) 00000000
DSI_VC_LONG_PACKET_PAYLOAD(1) 00000000
DSI_VC_SHORT_PACKET_HEADER(1) 00000000
DSI_VC_IRQSTATUS(1) 00000000
DSI_VC_IRQENABLE(1) 00000000
DSI_VC_CTRL(2) 00000000
DSI_VC_TE(2) 00000000
DSI_VC_LONG_PACKET_HEADER(2) 00000000
DSI_VC_LONG_PACKET_PAYLOAD(2) 00000000
DSI_VC_SHORT_PACKET_HEADER(2) 00000000
DSI_VC_IRQSTATUS(2) 00000000
DSI_VC_IRQENABLE(2) 00000000
DSI_VC_CTRL(3) 00000000
DSI_VC_TE(3) 00000000
DSI_VC_LONG_PACKET_HEADER(3) 00000000
DSI_VC_LONG_PACKET_PAYLOAD(3) 00000000
DSI_VC_SHORT_PACKET_HEADER(3) 00000000
DSI_VC_IRQSTATUS(3) 00000000
DSI_VC_IRQENABLE(3) 00000000
DSI_DSIPHY_CFG0 1e481d3a
DSI_DSIPHY_CFG1 420a1a6a
DSI_DSIPHY_CFG2 b800001a
DSI_DSIPHY_CFG5 60000000
DSI_PLL_CONTROL 00000000
DSI_PLL_STATUS 00000383
DSI_PLL_GO 00000000
DSI_PLL_CONFIGURATION1 05d90e19
DSI_PLL_CONFIGURATION2 0005600e
Of special interest is the DSI_COMPLEXIO_CFG1. RESET_DONE is not set,
not does the PWR_STATUS match the command given. The
LDO_POWER_GOOD_STATE is asserted however.
The DSI is powered and all the clocks seem to be on and the DSI PLL
locks. Just the complex IO will not power on. I am using a 2.6.32.9
kernel so it is not the latest but I wanted to ask if someone had any
idea where to look next before porting the latest onto our board.
Thanks,
- Juha
--
Duck tape is like the force, it has a light side and a dark side and
it holds the universe together.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Issue with DSS DSI: Complex IO not powering on
2011-04-06 1:55 Issue with DSS DSI: Complex IO not powering on Juha Kuikka
@ 2011-04-06 6:16 ` Archit Taneja
2011-04-07 2:49 ` Juha Kuikka
0 siblings, 1 reply; 4+ messages in thread
From: Archit Taneja @ 2011-04-06 6:16 UTC (permalink / raw)
To: Juha Kuikka; +Cc: linux-omap@vger.kernel.org Mailing List
Hi,
On Wednesday 06 April 2011 07:25 AM, Juha Kuikka wrote:
> Hi,
> I am working on a custom board with DM3730 and a DSI panel and I have
> a problem in powering on the DSI complex IO block.
>
> The DSS DSI initialization fails with:
> omapdss DSI: dsi_complexio_init
> omapdss DSI error: complexio reset not done!<-- my own addition
> omapdss DSI error: failed to set complexio power state to 1
>
Can you check if the necessary pad/pin-muxing has been done for the DSI
lanes?
Archit
> The DSI PLL is used and configured according to the example values in
> the TRM (not proper for our panel but they should enable the complex
> IO to at least power on, right).
>
> Output form DSS DEBUG:
> omapdss DSI: LP_CLK_DIV 6, LP_CLK 7500000
> omapdss DISPC: lck = 90000000 (1)
> omapdss DISPC: pck = 30000000 (3)
> - DSI PLL -
> dsi pll source = dss2_alwon_fclk
> Fint 2000000 regn 13
> CLKIN4DDR 1080000000 regm 270
> dsi1_pll_fck 90000000 regm3 12 (on)
> dsi2_pll_fck 90000000 regm4 12 (on)
> - DSI -
> dsi fclk source = dsi2_pll_fclk
> DSI_FCLK 90000000
> DDR_CLK 270000000
> TxByteClkHS 67500000
> LP_CLK 7500000
> VP_CLK 90000000
> VP_PCLK 30000000
>
> As far as I can tell these values fill all the requirements set in the
> TRM for clock rates and their ratios.
>
> After the fail in dsi_complexio_init I dump all registers:
>
> DSI_REVISION 00000010
> DSI_SYSCONFIG 00000011
> DSI_SYSSTATUS 00000001
> DSI_IRQSTATUS 00080080
> DSI_IRQENABLE 00000000
> DSI_CTRL 00000100
> DSI_COMPLEXIO_CFG1 48200321
> DSI_COMPLEXIO_IRQ_STATUS 00000000
> DSI_COMPLEXIO_IRQ_ENABLE 00000000
> DSI_CLK_CTRL a0304006
> DSI_TIMING1 7fff7fff
> DSI_TIMING2 7fff7fff
> DSI_VM_TIMING1 00000000
> DSI_VM_TIMING2 00000000
> DSI_VM_TIMING3 00000000
> DSI_CLK_TIMING 00000101
> DSI_TX_FIFO_VC_SIZE 00000000
> DSI_RX_FIFO_VC_SIZE 00000000
> DSI_COMPLEXIO_CFG2 00000000
> DSI_RX_FIFO_VC_FULLNESS 00000000
> DSI_VM_TIMING4 00000000
> DSI_TX_FIFO_VC_EMPTINESS 00000000
> DSI_VM_TIMING5 00000000
> DSI_VM_TIMING6 00000000
> DSI_VM_TIMING7 00000000
> DSI_STOPCLK_TIMING 00000080
> DSI_VC_CTRL(0) 00000000
> DSI_VC_TE(0) 00000000
> DSI_VC_LONG_PACKET_HEADER(0) 00000000
> DSI_VC_LONG_PACKET_PAYLOAD(0) 00000000
> DSI_VC_SHORT_PACKET_HEADER(0) 00000000
> DSI_VC_IRQSTATUS(0) 00000000
> DSI_VC_IRQENABLE(0) 00000000
> DSI_VC_CTRL(1) 00000000
> DSI_VC_TE(1) 00000000
> DSI_VC_LONG_PACKET_HEADER(1) 00000000
> DSI_VC_LONG_PACKET_PAYLOAD(1) 00000000
> DSI_VC_SHORT_PACKET_HEADER(1) 00000000
> DSI_VC_IRQSTATUS(1) 00000000
> DSI_VC_IRQENABLE(1) 00000000
> DSI_VC_CTRL(2) 00000000
> DSI_VC_TE(2) 00000000
> DSI_VC_LONG_PACKET_HEADER(2) 00000000
> DSI_VC_LONG_PACKET_PAYLOAD(2) 00000000
> DSI_VC_SHORT_PACKET_HEADER(2) 00000000
> DSI_VC_IRQSTATUS(2) 00000000
> DSI_VC_IRQENABLE(2) 00000000
> DSI_VC_CTRL(3) 00000000
> DSI_VC_TE(3) 00000000
> DSI_VC_LONG_PACKET_HEADER(3) 00000000
> DSI_VC_LONG_PACKET_PAYLOAD(3) 00000000
> DSI_VC_SHORT_PACKET_HEADER(3) 00000000
> DSI_VC_IRQSTATUS(3) 00000000
> DSI_VC_IRQENABLE(3) 00000000
> DSI_DSIPHY_CFG0 1e481d3a
> DSI_DSIPHY_CFG1 420a1a6a
> DSI_DSIPHY_CFG2 b800001a
> DSI_DSIPHY_CFG5 60000000
> DSI_PLL_CONTROL 00000000
> DSI_PLL_STATUS 00000383
> DSI_PLL_GO 00000000
> DSI_PLL_CONFIGURATION1 05d90e19
> DSI_PLL_CONFIGURATION2 0005600e
>
> Of special interest is the DSI_COMPLEXIO_CFG1. RESET_DONE is not set,
> not does the PWR_STATUS match the command given. The
> LDO_POWER_GOOD_STATE is asserted however.
>
> The DSI is powered and all the clocks seem to be on and the DSI PLL
> locks. Just the complex IO will not power on. I am using a 2.6.32.9
> kernel so it is not the latest but I wanted to ask if someone had any
> idea where to look next before porting the latest onto our board.
>
> Thanks,
> - Juha
>
> --
> Duck tape is like the force, it has a light side and a dark side and
> it holds the universe together.
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Issue with DSS DSI: Complex IO not powering on
2011-04-06 6:16 ` Archit Taneja
@ 2011-04-07 2:49 ` Juha Kuikka
2011-04-07 5:45 ` Archit Taneja
0 siblings, 1 reply; 4+ messages in thread
From: Juha Kuikka @ 2011-04-07 2:49 UTC (permalink / raw)
To: Archit Taneja; +Cc: linux-omap@vger.kernel.org Mailing List
On Tue, Apr 5, 2011 at 11:16 PM, Archit Taneja <archit@ti.com> wrote:
> Hi,
>
> On Wednesday 06 April 2011 07:25 AM, Juha Kuikka wrote:
>>
>> Hi,
>> I am working on a custom board with DM3730 and a DSI panel and I have
>> a problem in powering on the DSI complex IO block.
>>
>> The DSS DSI initialization fails with:
>> omapdss DSI: dsi_complexio_init
>> omapdss DSI error: complexio reset not done!<-- my own addition
>> omapdss DSI error: failed to set complexio power state to 1
>>
> Can you check if the necessary pad/pin-muxing has been done for the DSI
> lanes?
Thank you for the advice! Turns out they were not. After configuring
them the DSI powers on correctly.
Unfortunately I ran into another issue, it seems that dispc is not
giving us FRAMEDONE interrupt, currently investigating why.
Any input is appreciated.
Clocking:
omapdss DSI: PLL init
omapdss DSI: PLL init done
omapdss DSI: dsi_pll_set_clock_div()
omapdss DSI: DSI Fint 2000000
omapdss DSI: clkin (dss2_fck) rate 26000000, highfreq 0
omapdss DSI: CLKIN4DDR = 2 * 180 / 13 * 26000000 / 1 = 720000000
omapdss DSI: Data rate on 1 DSI lane 360 Mbps
omapdss DSI: Clock lane freq 180000000 Hz
omapdss DSI: regm3 = 8, dsi1_pll_fclk = 90000000
omapdss DSI: regm4 = 8, dsi2_pll_fclk = 90000000
omapdss DSI: PLL config done
omapdss DSI: PLL OK
omapdss DISPC: lck = 90000000 (1)
omapdss DISPC: pck = 30000000 (3)
DISPC is using DSI_DPLL1 as fclk.
Logs:
mapdss MANAGER: omap_dss_mgr_apply(lcd)
omapdss OVERLAY: check_overlay 0: (0,0 480x800 -> 0x800) disp (480x800)
omapdss MANAGER: configure_overlay(0)
omapdss DISPC: dispc_setup_plane 0, pa 81430000, sw 480, 0,0, 480x800
-> 480x800, ilace 0, cmode 40, rot 0, mir 0 flicker_filter 0
omapdss DISPC: calc_rot(0): scrw 480, 480x800
omapdss DISPC: offset0 0, offset1 0, row_inc 1, pix_inc 1
omapdss DISPC: 0,0 480x800 -> 480x800
omapdss DISPC: vid[0] attributes = c
omapdss DISPC: fifo(0) low/high old 960/1023, new 512/960
omapdss DISPC: dispc_enable_plane 0, 1
omapdss DSI: starting auto update
omapdss DSI: dsi_display_enable_te(0)
omapdss DSI: dsi_display_set_update_mode(2)
dsi_display_update lcd_ix=0
omapdss DSI: dsi_display_update(0,0 480x800)
omapdss MANAGER: dispc_setup_partial_planes 0,0 480x800
omapdss MANAGER: configure_overlay(0)
omapdss DISPC: dispc_setup_plane 0, pa 81430000, sw 480, 0,0, 480x800
-> 480x800, ilace 0, cmode 40, rot 0, mir 0 flicker_filter 0
omapdss DISPC: calc_rot(0): scrw 480, 480x800
omapdss DISPC: offset0 0, offset1 0, row_inc 1, pix_inc 1
omapdss DISPC: 0,0 480x800 -> 480x800
omapdss DISPC: vid[0] attributes = ad
omapdss DISPC: fifo(0) low/high old 512/960, new 512/960
omapdss DISPC: dispc_enable_plane 0, 1
omapdss MANAGER: configure_overlay(1)
omapdss DISPC: dispc_enable_plane 1, 0
omapdss MANAGER: configure_overlay(2)
omapdss DISPC: dispc_enable_plane 2, 0
omapdss MANAGER: configure_manager(0)
omapdss DSI: dsi_vc_config_vp(0)
omapdss DSI: dsi_vc_enable channel 0, enable 0
omapdss DSI: dsi_vc_enable channel 0, enable 1
omapdss DSI: dsi_update_screen_dispc(0,0 480x800)
omapdss DSI: dsi_display_enable_te(0)
omapdss DSI: dsi_display_set_update_mode(2)
omapdss DSI error: framedone timeout
omapdss DSI error: failed update 0,0 480x800
omapdss DISPC error: timeout waiting for FRAME DONE
- Juha
>
> Archit
>>
>> The DSI PLL is used and configured according to the example values in
>> the TRM (not proper for our panel but they should enable the complex
>> IO to at least power on, right).
>>
>> Output form DSS DEBUG:
>> omapdss DSI: LP_CLK_DIV 6, LP_CLK 7500000
>> omapdss DISPC: lck = 90000000 (1)
>> omapdss DISPC: pck = 30000000 (3)
>> - DSI PLL -
>> dsi pll source = dss2_alwon_fclk
>> Fint 2000000 regn 13
>> CLKIN4DDR 1080000000 regm 270
>> dsi1_pll_fck 90000000 regm3 12 (on)
>> dsi2_pll_fck 90000000 regm4 12 (on)
>> - DSI -
>> dsi fclk source = dsi2_pll_fclk
>> DSI_FCLK 90000000
>> DDR_CLK 270000000
>> TxByteClkHS 67500000
>> LP_CLK 7500000
>> VP_CLK 90000000
>> VP_PCLK 30000000
>>
>> As far as I can tell these values fill all the requirements set in the
>> TRM for clock rates and their ratios.
>>
>> After the fail in dsi_complexio_init I dump all registers:
>>
>> DSI_REVISION 00000010
>> DSI_SYSCONFIG 00000011
>> DSI_SYSSTATUS 00000001
>> DSI_IRQSTATUS 00080080
>> DSI_IRQENABLE 00000000
>> DSI_CTRL 00000100
>> DSI_COMPLEXIO_CFG1 48200321
>> DSI_COMPLEXIO_IRQ_STATUS 00000000
>> DSI_COMPLEXIO_IRQ_ENABLE 00000000
>> DSI_CLK_CTRL a0304006
>> DSI_TIMING1 7fff7fff
>> DSI_TIMING2 7fff7fff
>> DSI_VM_TIMING1 00000000
>> DSI_VM_TIMING2 00000000
>> DSI_VM_TIMING3 00000000
>> DSI_CLK_TIMING 00000101
>> DSI_TX_FIFO_VC_SIZE 00000000
>> DSI_RX_FIFO_VC_SIZE 00000000
>> DSI_COMPLEXIO_CFG2 00000000
>> DSI_RX_FIFO_VC_FULLNESS 00000000
>> DSI_VM_TIMING4 00000000
>> DSI_TX_FIFO_VC_EMPTINESS 00000000
>> DSI_VM_TIMING5 00000000
>> DSI_VM_TIMING6 00000000
>> DSI_VM_TIMING7 00000000
>> DSI_STOPCLK_TIMING 00000080
>> DSI_VC_CTRL(0) 00000000
>> DSI_VC_TE(0) 00000000
>> DSI_VC_LONG_PACKET_HEADER(0) 00000000
>> DSI_VC_LONG_PACKET_PAYLOAD(0) 00000000
>> DSI_VC_SHORT_PACKET_HEADER(0) 00000000
>> DSI_VC_IRQSTATUS(0) 00000000
>> DSI_VC_IRQENABLE(0) 00000000
>> DSI_VC_CTRL(1) 00000000
>> DSI_VC_TE(1) 00000000
>> DSI_VC_LONG_PACKET_HEADER(1) 00000000
>> DSI_VC_LONG_PACKET_PAYLOAD(1) 00000000
>> DSI_VC_SHORT_PACKET_HEADER(1) 00000000
>> DSI_VC_IRQSTATUS(1) 00000000
>> DSI_VC_IRQENABLE(1) 00000000
>> DSI_VC_CTRL(2) 00000000
>> DSI_VC_TE(2) 00000000
>> DSI_VC_LONG_PACKET_HEADER(2) 00000000
>> DSI_VC_LONG_PACKET_PAYLOAD(2) 00000000
>> DSI_VC_SHORT_PACKET_HEADER(2) 00000000
>> DSI_VC_IRQSTATUS(2) 00000000
>> DSI_VC_IRQENABLE(2) 00000000
>> DSI_VC_CTRL(3) 00000000
>> DSI_VC_TE(3) 00000000
>> DSI_VC_LONG_PACKET_HEADER(3) 00000000
>> DSI_VC_LONG_PACKET_PAYLOAD(3) 00000000
>> DSI_VC_SHORT_PACKET_HEADER(3) 00000000
>> DSI_VC_IRQSTATUS(3) 00000000
>> DSI_VC_IRQENABLE(3) 00000000
>> DSI_DSIPHY_CFG0 1e481d3a
>> DSI_DSIPHY_CFG1 420a1a6a
>> DSI_DSIPHY_CFG2 b800001a
>> DSI_DSIPHY_CFG5 60000000
>> DSI_PLL_CONTROL 00000000
>> DSI_PLL_STATUS 00000383
>> DSI_PLL_GO 00000000
>> DSI_PLL_CONFIGURATION1 05d90e19
>> DSI_PLL_CONFIGURATION2 0005600e
>>
>> Of special interest is the DSI_COMPLEXIO_CFG1. RESET_DONE is not set,
>> not does the PWR_STATUS match the command given. The
>> LDO_POWER_GOOD_STATE is asserted however.
>>
>> The DSI is powered and all the clocks seem to be on and the DSI PLL
>> locks. Just the complex IO will not power on. I am using a 2.6.32.9
>> kernel so it is not the latest but I wanted to ask if someone had any
>> idea where to look next before porting the latest onto our board.
>>
>> Thanks,
>> - Juha
>>
>> --
>> Duck tape is like the force, it has a light side and a dark side and
>> it holds the universe together.
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
>> the body of a message to majordomo@vger.kernel.org
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>
>
>
--
Duck tape is like the force, it has a light side and a dark side and
it holds the universe together.
--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: Issue with DSS DSI: Complex IO not powering on
2011-04-07 2:49 ` Juha Kuikka
@ 2011-04-07 5:45 ` Archit Taneja
0 siblings, 0 replies; 4+ messages in thread
From: Archit Taneja @ 2011-04-07 5:45 UTC (permalink / raw)
To: Juha Kuikka; +Cc: linux-omap@vger.kernel.org Mailing List
Hi,
On Thursday 07 April 2011 08:19 AM, Juha Kuikka wrote:
> On Tue, Apr 5, 2011 at 11:16 PM, Archit Taneja<archit@ti.com> wrote:
>> Hi,
>>
>> On Wednesday 06 April 2011 07:25 AM, Juha Kuikka wrote:
>>>
>>> Hi,
>>> I am working on a custom board with DM3730 and a DSI panel and I have
>>> a problem in powering on the DSI complex IO block.
>>>
>>> The DSS DSI initialization fails with:
>>> omapdss DSI: dsi_complexio_init
>>> omapdss DSI error: complexio reset not done!<-- my own addition
>>> omapdss DSI error: failed to set complexio power state to 1
>>>
>> Can you check if the necessary pad/pin-muxing has been done for the DSI
>> lanes?
>
> Thank you for the advice! Turns out they were not. After configuring
> them the DSI powers on correctly.
>
> Unfortunately I ran into another issue, it seems that dispc is not
> giving us FRAMEDONE interrupt, currently investigating why.
>
> Any input is appreciated.
A couple of questions:
It is a command mode or video mode panel?
Are other commands to the panel going through successfully?
Could you point to the kernel source you are using?
>
> Clocking:
> omapdss DSI: PLL init
> omapdss DSI: PLL init done
> omapdss DSI: dsi_pll_set_clock_div()
> omapdss DSI: DSI Fint 2000000
> omapdss DSI: clkin (dss2_fck) rate 26000000, highfreq 0
> omapdss DSI: CLKIN4DDR = 2 * 180 / 13 * 26000000 / 1 = 720000000
> omapdss DSI: Data rate on 1 DSI lane 360 Mbps
> omapdss DSI: Clock lane freq 180000000 Hz
> omapdss DSI: regm3 = 8, dsi1_pll_fclk = 90000000
> omapdss DSI: regm4 = 8, dsi2_pll_fclk = 90000000
> omapdss DSI: PLL config done
> omapdss DSI: PLL OK
> omapdss DISPC: lck = 90000000 (1)
> omapdss DISPC: pck = 30000000 (3)
>
90 Mhz for DISPC and DSI FCLK seems to be a bit low, you may want to
increase that.
Archit
> DISPC is using DSI_DPLL1 as fclk.
>
> Logs:
> mapdss MANAGER: omap_dss_mgr_apply(lcd)
> omapdss OVERLAY: check_overlay 0: (0,0 480x800 -> 0x800) disp (480x800)
> omapdss MANAGER: configure_overlay(0)
> omapdss DISPC: dispc_setup_plane 0, pa 81430000, sw 480, 0,0, 480x800
> -> 480x800, ilace 0, cmode 40, rot 0, mir 0 flicker_filter 0
> omapdss DISPC: calc_rot(0): scrw 480, 480x800
> omapdss DISPC: offset0 0, offset1 0, row_inc 1, pix_inc 1
> omapdss DISPC: 0,0 480x800 -> 480x800
> omapdss DISPC: vid[0] attributes = c
> omapdss DISPC: fifo(0) low/high old 960/1023, new 512/960
> omapdss DISPC: dispc_enable_plane 0, 1
> omapdss DSI: starting auto update
> omapdss DSI: dsi_display_enable_te(0)
> omapdss DSI: dsi_display_set_update_mode(2)
> dsi_display_update lcd_ix=0
> omapdss DSI: dsi_display_update(0,0 480x800)
> omapdss MANAGER: dispc_setup_partial_planes 0,0 480x800
> omapdss MANAGER: configure_overlay(0)
> omapdss DISPC: dispc_setup_plane 0, pa 81430000, sw 480, 0,0, 480x800
> -> 480x800, ilace 0, cmode 40, rot 0, mir 0 flicker_filter 0
> omapdss DISPC: calc_rot(0): scrw 480, 480x800
> omapdss DISPC: offset0 0, offset1 0, row_inc 1, pix_inc 1
> omapdss DISPC: 0,0 480x800 -> 480x800
> omapdss DISPC: vid[0] attributes = ad
> omapdss DISPC: fifo(0) low/high old 512/960, new 512/960
> omapdss DISPC: dispc_enable_plane 0, 1
> omapdss MANAGER: configure_overlay(1)
> omapdss DISPC: dispc_enable_plane 1, 0
> omapdss MANAGER: configure_overlay(2)
> omapdss DISPC: dispc_enable_plane 2, 0
> omapdss MANAGER: configure_manager(0)
> omapdss DSI: dsi_vc_config_vp(0)
> omapdss DSI: dsi_vc_enable channel 0, enable 0
> omapdss DSI: dsi_vc_enable channel 0, enable 1
> omapdss DSI: dsi_update_screen_dispc(0,0 480x800)
> omapdss DSI: dsi_display_enable_te(0)
> omapdss DSI: dsi_display_set_update_mode(2)
> omapdss DSI error: framedone timeout
> omapdss DSI error: failed update 0,0 480x800
> omapdss DISPC error: timeout waiting for FRAME DONE
>
> - Juha
>
>>
>> Archit
>>>
>>> The DSI PLL is used and configured according to the example values in
>>> the TRM (not proper for our panel but they should enable the complex
>>> IO to at least power on, right).
>>>
>>> Output form DSS DEBUG:
>>> omapdss DSI: LP_CLK_DIV 6, LP_CLK 7500000
>>> omapdss DISPC: lck = 90000000 (1)
>>> omapdss DISPC: pck = 30000000 (3)
>>> - DSI PLL -
>>> dsi pll source = dss2_alwon_fclk
>>> Fint 2000000 regn 13
>>> CLKIN4DDR 1080000000 regm 270
>>> dsi1_pll_fck 90000000 regm3 12 (on)
>>> dsi2_pll_fck 90000000 regm4 12 (on)
>>> - DSI -
>>> dsi fclk source = dsi2_pll_fclk
>>> DSI_FCLK 90000000
>>> DDR_CLK 270000000
>>> TxByteClkHS 67500000
>>> LP_CLK 7500000
>>> VP_CLK 90000000
>>> VP_PCLK 30000000
>>>
>>> As far as I can tell these values fill all the requirements set in the
>>> TRM for clock rates and their ratios.
>>>
>>> After the fail in dsi_complexio_init I dump all registers:
>>>
>>> DSI_REVISION 00000010
>>> DSI_SYSCONFIG 00000011
>>> DSI_SYSSTATUS 00000001
>>> DSI_IRQSTATUS 00080080
>>> DSI_IRQENABLE 00000000
>>> DSI_CTRL 00000100
>>> DSI_COMPLEXIO_CFG1 48200321
>>> DSI_COMPLEXIO_IRQ_STATUS 00000000
>>> DSI_COMPLEXIO_IRQ_ENABLE 00000000
>>> DSI_CLK_CTRL a0304006
>>> DSI_TIMING1 7fff7fff
>>> DSI_TIMING2 7fff7fff
>>> DSI_VM_TIMING1 00000000
>>> DSI_VM_TIMING2 00000000
>>> DSI_VM_TIMING3 00000000
>>> DSI_CLK_TIMING 00000101
>>> DSI_TX_FIFO_VC_SIZE 00000000
>>> DSI_RX_FIFO_VC_SIZE 00000000
>>> DSI_COMPLEXIO_CFG2 00000000
>>> DSI_RX_FIFO_VC_FULLNESS 00000000
>>> DSI_VM_TIMING4 00000000
>>> DSI_TX_FIFO_VC_EMPTINESS 00000000
>>> DSI_VM_TIMING5 00000000
>>> DSI_VM_TIMING6 00000000
>>> DSI_VM_TIMING7 00000000
>>> DSI_STOPCLK_TIMING 00000080
>>> DSI_VC_CTRL(0) 00000000
>>> DSI_VC_TE(0) 00000000
>>> DSI_VC_LONG_PACKET_HEADER(0) 00000000
>>> DSI_VC_LONG_PACKET_PAYLOAD(0) 00000000
>>> DSI_VC_SHORT_PACKET_HEADER(0) 00000000
>>> DSI_VC_IRQSTATUS(0) 00000000
>>> DSI_VC_IRQENABLE(0) 00000000
>>> DSI_VC_CTRL(1) 00000000
>>> DSI_VC_TE(1) 00000000
>>> DSI_VC_LONG_PACKET_HEADER(1) 00000000
>>> DSI_VC_LONG_PACKET_PAYLOAD(1) 00000000
>>> DSI_VC_SHORT_PACKET_HEADER(1) 00000000
>>> DSI_VC_IRQSTATUS(1) 00000000
>>> DSI_VC_IRQENABLE(1) 00000000
>>> DSI_VC_CTRL(2) 00000000
>>> DSI_VC_TE(2) 00000000
>>> DSI_VC_LONG_PACKET_HEADER(2) 00000000
>>> DSI_VC_LONG_PACKET_PAYLOAD(2) 00000000
>>> DSI_VC_SHORT_PACKET_HEADER(2) 00000000
>>> DSI_VC_IRQSTATUS(2) 00000000
>>> DSI_VC_IRQENABLE(2) 00000000
>>> DSI_VC_CTRL(3) 00000000
>>> DSI_VC_TE(3) 00000000
>>> DSI_VC_LONG_PACKET_HEADER(3) 00000000
>>> DSI_VC_LONG_PACKET_PAYLOAD(3) 00000000
>>> DSI_VC_SHORT_PACKET_HEADER(3) 00000000
>>> DSI_VC_IRQSTATUS(3) 00000000
>>> DSI_VC_IRQENABLE(3) 00000000
>>> DSI_DSIPHY_CFG0 1e481d3a
>>> DSI_DSIPHY_CFG1 420a1a6a
>>> DSI_DSIPHY_CFG2 b800001a
>>> DSI_DSIPHY_CFG5 60000000
>>> DSI_PLL_CONTROL 00000000
>>> DSI_PLL_STATUS 00000383
>>> DSI_PLL_GO 00000000
>>> DSI_PLL_CONFIGURATION1 05d90e19
>>> DSI_PLL_CONFIGURATION2 0005600e
>>>
>>> Of special interest is the DSI_COMPLEXIO_CFG1. RESET_DONE is not set,
>>> not does the PWR_STATUS match the command given. The
>>> LDO_POWER_GOOD_STATE is asserted however.
>>>
>>> The DSI is powered and all the clocks seem to be on and the DSI PLL
>>> locks. Just the complex IO will not power on. I am using a 2.6.32.9
>>> kernel so it is not the latest but I wanted to ask if someone had any
>>> idea where to look next before porting the latest onto our board.
>>>
>>> Thanks,
>>> - Juha
>>>
>>> --
>>> Duck tape is like the force, it has a light side and a dark side and
>>> it holds the universe together.
>>> --
>>> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
>>> the body of a message to majordomo@vger.kernel.org
>>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>>>
>>
>>
>
>
>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2011-04-07 5:40 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2011-04-06 1:55 Issue with DSS DSI: Complex IO not powering on Juha Kuikka
2011-04-06 6:16 ` Archit Taneja
2011-04-07 2:49 ` Juha Kuikka
2011-04-07 5:45 ` Archit Taneja
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).