Re: Panda ES board hang when using GPIO as interrupt

[Jon Hunter <jon-hunter-l0cyMroinI0@public.gmane.org>]

Hi Franky,

On 06/27/2012 08:03 PM, Franky Lin wrote:
> On 06/27/2012 04:43 PM, Jon Hunter wrote:
>> Hi Franky,
>>
>> On 06/25/2012 03:52 PM, Franky Lin wrote:
>>> Hi Kevin, Tarun,
>>>
>>> We are using the expansion connector A on Panda board to mount a SDIO
>>> WiFi dongle on MMC2 with a level triggered interrupt signal connected to
>>> GPIO 138. It's been working fine until 3.5 rc1. The board hang randomly
>>> within 5 mins during a network traffic test. After bisecting we found
>>> the culprit is "[PATCH 8/8] gpio/omap: fix missing check in
>>> *_runtime_suspend()" [1].
>>
>> I have been looking into this today to see if I can replicate the
>> problem that you have reported. However, so far I have not had any luck.
>> Please note that my test setup is not exactly the same as yours as I
>> don't have your wlan module. However, I have been using a 2nd board to
>> generate gpio events to a panda-es to see I can make it lock up. I have
>> tried mainline kernel 3.5-rc1 and 3.5-rc3 but I have not seen any
>> problems after sending 100k gpio events (over many minutes). My setup is
>> as follows ...
>>
>> - OMAP4460 panda-es with gpio-138 connected to OMAP3430 beagle gpio-11.
>> - Mainline kernel 3.5-rc1/3 using omap2plus_defconfig (no changes)
>> - Created a simple kernel module that acquires gpio-138 and sets up a
>>    IRQ with flag IRQF_TRIGGER_HIGH (for active high level interrupt).
>> - GPIO events are triggered roughly every 1ms
> 
> Don't know if it's related, but we also mux several other pins on
> connector A:
>         /* MMC2 Mux for extension board */
>         /* MMC2 CMD */
>         OMAP4_MUX(GPMC_NWE, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
>         /* MMC2 CLK */
>         OMAP4_MUX(GPMC_NOE, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
>         /* MMC2 DAT 0-3 */
>         OMAP4_MUX(GPMC_AD0, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
>         OMAP4_MUX(GPMC_AD1, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
>         OMAP4_MUX(GPMC_AD2, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
>         OMAP4_MUX(GPMC_AD3, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
>         /* GPIO MUX for OOB interupt of dongle */
>         OMAP4_MUX(MCSPI1_CS1, OMAP_MUX_MODE3 | OMAP_PIN_INPUT_PULLDOWN),
>         /* GPIO MUX for WLAN_ENABLE for dongle */
>         OMAP4_MUX(MCSPI1_CLK, OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT),

I would not have thought so. However, I will think about that thanks.

>> Can you confirm ...
>> 1. You are just using omap2plus_defconfig with no changes?
> No, we enable following options
> CONFIG_DEVTMPFS=y
> CONFIG_DEVTMPFS_MOUNT=y
> CONFIG_USB_OHCI_HCD=y

Ok, thanks.

>> 2. Rough frequency of gpio events?
> 3367 interrupts were triggered during a 10 secs throughput test.
> 
>> 3. Is the gpio configured for active low or high?
> active high
> 
>> 4. When the hang occurs, what is the state of the gpio? Active or
>>     inactive? Can you probe it with a scope? If it was always active I
>>     could see that this would lock the device up, but I am not sure how
>>     that would relate to the results from your bisect???
> 
> I dont have a scope nearby. Let me see if I can find one tomorrow.

Great, that would be good.

>>> I noticed Kevin raised some similar cases on other platforms and also
>>> provided two patches in the patch mail thread. But unfortunately those
>>> two patches doesn't help in our case. I tested the driver with 3.5-rc3
>>> mainline kernel and the issue is still there. I can only "fix" the hang
>>> by either reverting the commit or disabling CONFIG_PM_RUNTIME. Also, the
>>> hang only happens on Panda ES board. Old Panda with 4430 works good.
>>
>> It does not make sense to me yet why this would only impact 4460, but I
>> will keep this in mind.
>>
>> In your wlan driver are you acquiring and freeing the gpio often? Or are
>> you only acquiring the gpio on boot?
>>
>> The reason I ask is because for omap4, it seems that we are not
>> currently calling omap2_gpio_prepare_for_idle() during idle and so the
>> only time I see us call the runtime_suspend/resume handlers for omap4 is
>> during probe and when we acquire and free the gpio.
>>
>> So if you were not acquiring and freeing the gpio and are using the
>> stock kernel, then as far as I can tell, the runtime pm code is not
>> being exercised much. My test is not acquiring and releasing the gpio
>> and so I am wondering if that is the secret to reproducing this
>> problem :-)
> 
> We only request the irq once during initialization. But we do frequently
> disable and re-enable it since we need to access to the module through
> SDIO to clear the interrupt. Apparently we can't finish all this in irq
> handler.

Ok, thanks. I don't see why that would cause a problem, but I can try
that too.

> Hope these could help.

Yes, good info to have.

Thanks
Jon
--
To unsubscribe from this list: send the line "unsubscribe linux-wireless" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html