public inbox for linux-omap@vger.kernel.org
 help / color / mirror / Atom feed
From: Keerthy <j-keerthy-l0cyMroinI0@public.gmane.org>
To: Lee Jones <lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org>
Cc: broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org,
	t-kristo-l0cyMroinI0@public.gmane.org,
	tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org,
	mark.rutland-5wv7dgnIgG8@public.gmane.org,
	linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Subject: Re: [PATCH 1/3] mfd: lp87565: Add lp87565 PMIC support
Date: Tue, 23 May 2017 08:30:34 +0530	[thread overview]
Message-ID: <4ae39bed-4004-c7d3-4e3e-3eeac98ca98f@ti.com> (raw)
In-Reply-To: <26169872-1b43-88d1-3e5b-367b4d446222-l0cyMroinI0@public.gmane.org>



On Tuesday 23 May 2017 08:05 AM, Keerthy wrote:
> 
> 
> On Monday 22 May 2017 11:18 PM, Lee Jones wrote:
>> On Fri, 19 May 2017, Keerthy wrote:
>>
>>> The LP87565 chip is a power management IC for Portable Navigation Systems
>>> and Tablet Computing devices. It contains the following components:
>>>
>>>         - Configurable Bucks(Single and multi-phase).
>>>         - Configurable General Purpose Output Signals (GPO).
>>>
>>> The LP87565-Q1 variant device uses two 2-phase outputs configuration,
>>> Buck0 is master for Buck0/1 output and Buck2 is master for Buck2/3
>>> output.
>>>
>>> Signed-off-by: Keerthy <j-keerthy-l0cyMroinI0@public.gmane.org>
>>> ---
>>>  Documentation/devicetree/bindings/mfd/lp87565.txt |  44 ++++
>>>  drivers/mfd/Kconfig                               |  14 ++
>>>  drivers/mfd/Makefile                              |   1 +
>>>  drivers/mfd/lp87565.c                             | 103 ++++++++
>>>  include/linux/mfd/lp87565.h                       | 275 ++++++++++++++++++++++
>>>  5 files changed, 437 insertions(+)
>>>  create mode 100644 Documentation/devicetree/bindings/mfd/lp87565.txt
>>>  create mode 100644 drivers/mfd/lp87565.c
>>>  create mode 100644 include/linux/mfd/lp87565.h
>>>
>>> diff --git a/Documentation/devicetree/bindings/mfd/lp87565.txt b/Documentation/devicetree/bindings/mfd/lp87565.txt
>>> new file mode 100644
>>> index 0000000..38a00a1
>>> --- /dev/null
>>> +++ b/Documentation/devicetree/bindings/mfd/lp87565.txt
>>> @@ -0,0 +1,44 @@
>>> +TI LP873565 PMIC MFD driver
>>> +
>>> +Required properties:
>>> +  - compatible:	"ti,lp87565", "ti,lp87565-q1"
>>> +  - reg:		I2C slave address.
>>> +  - gpio-controller:	Marks the device node as a GPIO Controller.
>>> +  - #gpio-cells:	Should be two.  The first cell is the pin number and
>>> +			the second cell is used to specify flags.
>>> +			See ../gpio/gpio.txt for more information.
>>> +  - xxx-in-supply:	Phandle to parent supply node of each regulator
>>> +			populated under regulators node. xxx should match
>>> +			the supply_name populated in driver.
>>> +  - regulators:	List of child nodes that specify the regulator
>>> +			initialization data.
>>> +Example:
>>> +
>>> +lp87565: lp87565@60 {
>>> +	compatible = "ti,lp87565-q1";
>>> +	reg = <0x60>;
>>> +	gpio-controller;
>>> +	#gpio-cells = <2>;
>>> +
>>> +	buck10-in-supply =<&vsys_3v3>;
>>> +	buck23-in-supply =<&vsys_3v3>;
>>
>> White space errors.
>>
>> '\n' here.
> 
> I will fix this.
> 
>>
>>> +	regulators: regulators {
>>> +		buck10_reg: buck10 {
>>> +			/*VDD_MPU*/
>>
>> Whitespace errors.
> 
> I will fix this.
> 
>>
>>> +			regulator-name = "buck10";
>>> +			regulator-min-microvolt = <850000>;
>>> +			regulator-max-microvolt = <1250000>;
>>> +			regulator-always-on;
>>> +			regulator-boot-on;
>>> +		};
>>> +
>>> +		buck23_reg: buck23 {
>>> +			/* VDD_GPU*/
>>
>> Whitespace errors.
> 
> I will fix this.
> 
>>
>>> +			regulator-name = "buck23";
>>> +			regulator-min-microvolt = <850000>;
>>> +			regulator-max-microvolt = <1250000>;
>>> +			regulator-boot-on;
>>> +			regulator-always-on;
>>> +		};
>>> +	};
>>> +};
>>> diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig
>>> index 3eb5c93..5e884f3 100644
>>> --- a/drivers/mfd/Kconfig
>>> +++ b/drivers/mfd/Kconfig
>>> @@ -1325,6 +1325,20 @@ config MFD_TI_LP873X
>>>  	  This driver can also be built as a module. If so, the module
>>>  	  will be called lp873x.
>>>  
>>> +config MFD_TI_LP87565
>>> +	tristate "TI LP87565 Power Management IC"
>>> +	depends on I2C
>>> +	select MFD_CORE
>>> +	select REGMAP_I2C
>>> +	help
>>> +	  If you say yes here then you get support for the LP87565 series of
>>> +	  Power Management Integrated Circuits (PMIC).
>>> +	  These include voltage regulators, thermal protection, configurable
>>> +	  General Purpose Outputs (GPO) that are used in portable devices.
>>> +
>>> +	  This driver can also be built as a module. If so, the module
>>> +	  will be called lp87565.
>>> +
>>>  config MFD_TPS65218
>>>  	tristate "TI TPS65218 Power Management chips"
>>>  	depends on I2C
>>> diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
>>> index c16bf1e..7edbe1b 100644
>>> --- a/drivers/mfd/Makefile
>>> +++ b/drivers/mfd/Makefile
>>> @@ -25,6 +25,7 @@ obj-$(CONFIG_HTC_PASIC3)	+= htc-pasic3.o
>>>  obj-$(CONFIG_HTC_I2CPLD)	+= htc-i2cpld.o
>>>  
>>>  obj-$(CONFIG_MFD_TI_LP873X)	+= lp873x.o
>>> +obj-$(CONFIG_MFD_TI_LP87565)	+= lp87565.o
>>>  
>>>  obj-$(CONFIG_MFD_DAVINCI_VOICECODEC)	+= davinci_voicecodec.o
>>>  obj-$(CONFIG_MFD_DM355EVM_MSP)	+= dm355evm_msp.o
>>> diff --git a/drivers/mfd/lp87565.c b/drivers/mfd/lp87565.c
>>> new file mode 100644
>>> index 0000000..dff882f
>>> --- /dev/null
>>> +++ b/drivers/mfd/lp87565.c
>>> @@ -0,0 +1,103 @@
>>> +/*
>>> + * Copyright (C) 2017 Texas Instruments Incorporated - http://www.ti.com/
>>> + *
>>> + * Author: Keerthy <j-keerthy-l0cyMroinI0@public.gmane.org>
>>
>> We usually ask for full "first last" names.
> 
> Keerthy is my full name and i do not have a surname.
> 
>>
>>> + * This program is free software; you can redistribute it and/or
>>> + * modify it under the terms of the GNU General Public License as
>>> + * published by the Free Software Foundation version 2.
>>> + *
>>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>>> + * kind, whether express or implied; without even the implied warranty
>>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>>> + * GNU General Public License for more details.
>>
>> Can you use the short licence?
> 
> Okay Sure.

I hope the below is what you are looking for:

"This program is free software; you can redistribute  it and/or modify
it under  the terms of  the GNU General  Public License as published by
the Free Software Foundation;  either version 2 of the  License, or (at
your option) any later version."

> 
>>
>>> + */
>>> +
>>> +#include <linux/interrupt.h>
>>> +#include <linux/mfd/core.h>
>>> +#include <linux/module.h>
>>> +#include <linux/of_device.h>
>>> +#include <linux/regmap.h>
>>> +
>>> +#include <linux/mfd/lp87565.h>
>>> +
>>> +static const struct regmap_config lp87565_regmap_config = {
>>> +	.reg_bits = 8,
>>> +	.val_bits = 8,
>>> +	.max_register = LP87565_REG_MAX,
>>> +};
>>> +
>>> +static const struct mfd_cell lp87565_cells[] = {
>>> +	{ .name = "lp87565-q1-regulator", },
>>> +	{ .name = "lp87565-q1-gpio", },
>>> +};
>>> +
>>> +static const struct of_device_id of_lp87565_match_table[] = {
>>> +	{
>>> +		.compatible = "ti,lp87565-q1",
>>> +		.data = (void *)LP87565_DEVICE_TYPE_LP87565_Q1,
>>> +	},
>>> +	{}
>>> +};
>>> +MODULE_DEVICE_TABLE(of, of_lp87565_match_table);
>>> +
>>> +static int lp87565_probe(struct i2c_client *client,
>>> +			 const struct i2c_device_id *ids)
>>> +{
>>> +	struct lp87565 *lp87565;
>>> +	const struct of_device_id *of_id;
>>> +	int ret;
>>> +	unsigned int otpid;
>>> +
>>> +	lp87565 = devm_kzalloc(&client->dev, sizeof(*lp87565), GFP_KERNEL);
>>> +	if (!lp87565)
>>> +		return -ENOMEM;
>>> +
>>> +	lp87565->dev = &client->dev;
>>> +
>>> +	lp87565->regmap = devm_regmap_init_i2c(client, &lp87565_regmap_config);
>>> +	if (IS_ERR(lp87565->regmap)) {
>>> +		ret = PTR_ERR(lp87565->regmap);
>>> +		dev_err(lp87565->dev,
>>> +			"Failed to initialize register map: %d\n", ret);
>>> +		return ret;
>>> +	}
>>> +
>>> +	ret = regmap_read(lp87565->regmap, LP87565_REG_OTP_REV, &otpid);
>>> +	if (ret) {
>>> +		dev_err(lp87565->dev, "Failed to read OTP ID\n");
>>> +		return ret;
>>> +	}
>>> +
>>> +	lp87565->rev = otpid & LP87565_OTP_REV_OTP_ID;
>>
>> '\n' here.
> 
> Okay.
> 
>>
>>> +	of_id = of_match_device(of_lp87565_match_table, &client->dev);
>>> +	if (of_id)
>>> +		lp87565->dev_type = (enum lp87565_device_type)of_id->data;
>>> +
>>> +	i2c_set_clientdata(client, lp87565);
>>> +
>>> +	ret = mfd_add_devices(lp87565->dev, PLATFORM_DEVID_AUTO, lp87565_cells,
>>> +			      ARRAY_SIZE(lp87565_cells), NULL, 0, NULL);
>>> +
>>> +	return ret;
>>> +}
>>> +
>>> +static const struct i2c_device_id lp87565_id_table[] = {
>>> +	{ "lp87565-q1", 0 },
>>> +	{ },
>>> +};
>>> +MODULE_DEVICE_TABLE(i2c, lp87565_id_table);
>>
>> Is this an OF only driver, or not?

Yes OF only driver.

>>
>>> +static struct i2c_driver lp87565_driver = {
>>> +	.driver	= {
>>> +		.name	= "lp87565",
>>> +		.of_match_table = of_lp87565_match_table,
>>> +	},
>>> +	.probe		= lp87565_probe,
>>> +	.id_table	= lp87565_id_table,
>>> +};
>>> +module_i2c_driver(lp87565_driver);
>>> +
>>> +MODULE_AUTHOR("J Keerthy <j-keerthy-l0cyMroinI0@public.gmane.org>");
>>> +MODULE_DESCRIPTION("lp87565 chip family Multi-Function Device driver");
>>> +MODULE_LICENSE("GPL v2");
>>> diff --git a/include/linux/mfd/lp87565.h b/include/linux/mfd/lp87565.h
>>> new file mode 100644
>>> index 0000000..6112365
>>> --- /dev/null
>>> +++ b/include/linux/mfd/lp87565.h
>>> @@ -0,0 +1,275 @@
>>> +/*
>>> + * Functions to access LP87565 power management chip.
>>> + *
>>> + * Copyright (C) 2016 Texas Instruments Incorporated - http://www.ti.com/
>>
>> Please update the Copyright.
> 
> Oops yes. Thanks for catching it. I will fix in v2.
> 
> Thanks for reviewing it.
> 
>>
>>> + * This program is free software; you can redistribute it and/or
>>> + * modify it under the terms of the GNU General Public License as
>>> + * published by the Free Software Foundation version 2.
>>> + *
>>> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
>>> + * kind, whether express or implied; without even the implied warranty
>>> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
>>> + * GNU General Public License for more details.
>>> + */
>>> +
>>> +#ifndef __LINUX_MFD_LP87565_H
>>> +#define __LINUX_MFD_LP87565_H
>>> +
>>> +#include <linux/i2c.h>
>>> +#include <linux/regulator/driver.h>
>>> +#include <linux/regulator/machine.h>
>>> +
>>> +enum lp87565_device_type {
>>> +	LP87565_DEVICE_TYPE_UNKNOWN	= 0,
>>> +	LP87565_DEVICE_TYPE_LP87565_Q1,
>>> +};
>>> +
>>> +/* All register addresses */
>>> +#define LP87565_REG_DEV_REV		0X00
>>> +#define LP87565_REG_OTP_REV		0X01
>>> +#define LP87565_REG_BUCK0_CTRL_1		0X02
>>> +#define LP87565_REG_BUCK0_CTRL_2		0X03
>>> +
>>> +#define LP87565_REG_BUCK1_CTRL_1		0X04
>>> +#define LP87565_REG_BUCK1_CTRL_2		0X05
>>> +
>>> +#define LP87565_REG_BUCK2_CTRL_1		0X06
>>> +#define LP87565_REG_BUCK2_CTRL_2		0X07
>>> +
>>> +#define LP87565_REG_BUCK3_CTRL_1		0X08
>>> +#define LP87565_REG_BUCK3_CTRL_2		0X09
>>> +
>>> +#define LP87565_REG_BUCK0_VOUT			0X0A
>>> +#define LP87565_REG_BUCK0_FLOOR_VOUT		0X0B
>>> +
>>> +#define LP87565_REG_BUCK1_VOUT			0X0C
>>> +#define LP87565_REG_BUCK1_FLOOR_VOUT		0X0D
>>> +
>>> +#define LP87565_REG_BUCK2_VOUT			0X0E
>>> +#define LP87565_REG_BUCK2_FLOOR_VOUT		0X0F
>>> +
>>> +#define LP87565_REG_BUCK3_VOUT			0X10
>>> +#define LP87565_REG_BUCK3_FLOOR_VOUT		0X11
>>> +
>>> +#define LP87565_REG_BUCK0_DELAY			0X12
>>> +#define LP87565_REG_BUCK1_DELAY			0X13
>>> +
>>> +#define LP87565_REG_BUCK2_DELAY			0X14
>>> +#define LP87565_REG_BUCK3_DELAY			0X15
>>> +
>>> +#define LP87565_REG_GPO2_DELAY			0X16
>>> +#define LP87565_REG_GPO3_DELAY			0X17
>>> +#define LP87565_REG_RESET			0X18
>>> +#define LP87565_REG_CONFIG			0X19
>>> +
>>> +#define LP87565_REG_INT_TOP_1			0X1A
>>> +#define LP87565_REG_INT_TOP_2			0X1B
>>> +
>>> +#define LP87565_REG_INT_BUCK_0_1		0X1C
>>> +#define LP87565_REG_INT_BUCK_2_3		0X1D
>>> +#define LP87565_REG_TOP_STAT			0X1E
>>> +#define LP87565_REG_BUCK_0_1_STAT		0X1F
>>> +#define LP87565_REG_BUCK_2_3_STAT		0x20
>>> +
>>> +#define LP87565_REG_TOP_MASK_1			0x21
>>> +#define LP87565_REG_TOP_MASK_2			0x22
>>> +
>>> +#define LP87565_REG_BUCK_0_1_MASK		0x23
>>> +#define LP87565_REG_BUCK_2_3_MASK		0x24
>>> +#define LP87565_REG_SEL_I_LOAD			0x25
>>> +
>>> +#define LP87565_REG_I_LOAD_2			0x26
>>> +#define LP87565_REG_I_LOAD_1			0x27
>>> +
>>> +#define LP87565_REG_PGOOD_CTRL1			0x28
>>> +#define LP87565_REG_PGOOD_CTRL2			0x29
>>> +#define LP87565_REG_PGOOD_FLT			0x2A
>>> +#define LP87565_REG_PLL_CTRL			0x2B
>>> +#define LP87565_REG_PIN_FUNCTION		0x2C
>>> +#define LP87565_REG_GPIO_CONFIG			0x2D
>>> +#define LP87565_REG_GPIO_IN			0x2E
>>> +#define LP87565_REG_GPIO_OUT			0x2F
>>> +
>>> +#define LP87565_REG_MAX			LP87565_REG_GPIO_OUT
>>> +
>>> +/* Register field definitions */
>>> +#define LP87565_DEV_REV_DEV_ID			0xC0
>>> +#define LP87565_DEV_REV_ALL_LAYER		0x30
>>> +#define LP87565_DEV_REV_METAL_LAYER		0x0F
>>> +
>>> +#define LP87565_OTP_REV_OTP_ID			0xFF
>>> +
>>> +#define LP87565_BUCK_CTRL_1_EN			BIT(7)
>>> +#define LP87565_BUCK_CTRL_1_EN_PIN_CTRL		BIT(6)
>>> +#define LP87565_BUCK_CTRL_1_PIN_SELECT_EN	0x30
>>> +
>>> +#define LP87565_BUCK_CTRL_1_ROOF_FLOOR_EN	BIT(3)
>>> +#define LP87565_BUCK_CTRL_1_RDIS_EN		BIT(2)
>>> +#define LP87565_BUCK_CTRL_1_FPWM		BIT(1)
>>> +/* Bit0 is reserved for BUCK1 and BUCK3 and valid only for BUCK0 and BUCK2 */
>>> +#define LP87565_BUCK_CTRL_1_FPWM_MP_0_2		BIT(0)
>>> +
>>> +#define LP87565_BUCK_CTRL_2_ILIM		0x38
>>> +#define LP87565_BUCK_CTRL_2_SLEW_RATE		0x07
>>> +
>>> +#define LP87565_BUCK_VSET			0xFF
>>> +#define LP87565_BUCK_FLOOR_VSET			0xFF
>>> +
>>> +#define LP87565_BUCK_SHUTDOWN_DELAY		0xF0
>>> +#define LP87565_BUCK_STARTUP_DELAY		0x0F
>>> +
>>> +#define LP87565_GPIO_SHUTDOWN_DELAY		0xF0
>>> +#define LP87565_GPIO_STARTUP_DELAY		0x0F
>>> +
>>> +#define LP87565_RESET_SW_RESET			BIT(0)
>>> +
>>> +#define LP87565_CONFIG_DOUBLE_DELAY		BIT(7)
>>> +#define LP87565_CONFIG_CLKIN_PD			BIT(6)
>>> +#define LP87565_CONFIG_EN4_PD			BIT(5)
>>> +#define LP87565_CONFIG_EN3_PD			BIT(4)
>>> +#define LP87565_CONFIG_TDIE_WARN_LEVEL		BIT(3)
>>> +#define LP87565_CONFIG_EN2_PD			BIT(2)
>>> +#define LP87565_CONFIG_EN1_PD			BIT(1)
>>> +
>>> +#define LP87565_INT_GPIO			BIT(7)
>>> +#define LP87565_INT_BUCK23			BIT(6)
>>> +#define LP87565_INT_BUCK01			BIT(5)
>>> +#define LP87565_NO_SYNC_CLK			BIT(4)
>>> +#define LP87565_TDIE_SD				BIT(3)
>>> +#define LP87565_TDIE_WARN			BIT(2)
>>> +#define LP87565_INT_OVP				BIT(1)
>>> +#define LP87565_I_LOAD_READY			BIT(0)
>>> +
>>> +#define LP87565_INT_TOP2_RESET_REG		BIT(0)
>>> +
>>> +#define LP87565_BUCK1_PG_INT			BIT(6)
>>> +#define LP87565_BUCK1_SC_INT			BIT(5)
>>> +#define LP87565_BUCK1_ILIM_INT			BIT(4)
>>> +#define LP87565_BUCK0_PG_INT			BIT(2)
>>> +#define LP87565_BUCK0_SC_INT			BIT(1)
>>> +#define LP87565_BUCK0_ILIM_INT			BIT(0)
>>> +
>>> +#define LP87565_BUCK3_PG_INT			BIT(6)
>>> +#define LP87565_BUCK3_SC_INT			BIT(5)
>>> +#define LP87565_BUCK3_ILIM_INT			BIT(4)
>>> +#define LP87565_BUCK2_PG_INT			BIT(2)
>>> +#define LP87565_BUCK2_SC_INT			BIT(1)
>>> +#define LP87565_BUCK2_ILIM_INT			BIT(0)
>>> +
>>> +#define LP87565_SYNC_CLK_STAT			BIT(4)
>>> +#define LP87565_TDIE_SD_STAT			BIT(3)
>>> +#define LP87565_TDIE_WARN_STAT			BIT(2)
>>> +#define LP87565_OVP_STAT			BIT(1)
>>> +
>>> +#define LP87565_BUCK1_STAT			BIT(7)
>>> +#define LP87565_BUCK1_PG_STAT			BIT(6)
>>> +#define LP87565_BUCK1_ILIM_STAT			BIT(4)
>>> +#define LP87565_BUCK0_STAT			BIT(3)
>>> +#define LP87565_BUCK0_PG_STAT			BIT(2)
>>> +#define LP87565_BUCK0_ILIM_STAT			BIT(0)
>>> +
>>> +#define LP87565_BUCK3_STAT			BIT(7)
>>> +#define LP87565_BUCK3_PG_STAT			BIT(6)
>>> +#define LP87565_BUCK3_ILIM_STAT			BIT(4)
>>> +#define LP87565_BUCK2_STAT			BIT(3)
>>> +#define LP87565_BUCK2_PG_STAT			BIT(2)
>>> +#define LP87565_BUCK2_ILIM_STAT			BIT(0)
>>> +
>>> +#define LPL87565_GPIO_MASK			BIT(7)
>>> +#define LPL87565_SYNC_CLK_MASK			BIT(4)
>>> +#define LPL87565_TDIE_WARN_MASK			BIT(2)
>>> +#define LPL87565_I_LOAD_READY_MASK		BIT(0)
>>> +
>>> +#define LPL87565_RESET_REG_MASK			BIT(0)
>>> +
>>> +#define LPL87565_BUCK1_PG_MASK			BIT(6)
>>> +#define LPL87565_BUCK1_ILIM_MASK		BIT(4)
>>> +#define LPL87565_BUCK0_PG_MASK			BIT(2)
>>> +#define LPL87565_BUCK0_ILIM_MASK		BIT(0)
>>> +
>>> +#define LPL87565_BUCK3_PG_MASK			BIT(6)
>>> +#define LPL87565_BUCK3_ILIM_MASK		BIT(4)
>>> +#define LPL87565_BUCK2_PG_MASK			BIT(2)
>>> +#define LPL87565_BUCK2_ILIM_MASK		BIT(0)
>>> +
>>> +#define LP87565_LOAD_CURRENT_BUCK_SELECT	0x3
>>> +
>>> +#define LP87565_I_LOAD2_BUCK_LOAD_CURRENT	0x3
>>> +#define LP87565_I_LOAD1_BUCK_LOAD_CURRENT	0xFF
>>> +
>>> +#define LP87565_PG3_SEL				0xC0
>>> +#define LP87565_PG2_SEL				0x30
>>> +#define LP87565_PG1_SEL				0x0C
>>> +#define LP87565_PG0_SEL				0x03
>>> +
>>> +#define LP87565_HALF_DAY			BIT(7)
>>> +#define LP87565_EN_PG0_NINT			BIT(6)
>>> +#define LP87565_PGOOD_SET_DELAY			BIT(5)
>>> +#define LP87565_EN_PGFLT_STAT			BIT(4)
>>> +#define LP87565_PGOOD_WINDOW			BIT(2)
>>> +#define LP87565_PGOOD_OD			BIT(1)
>>> +#define LP87565_PGOOD_POL			BIT(0)
>>> +
>>> +#define LP87565_PG3_FLT				BIT(3)
>>> +#define LP87565_PG2_FLT				BIT(2)
>>> +#define LP87565_PG1_FLT				BIT(1)
>>> +#define LP87565_PG0_FLT				BIT(0)
>>> +
>>> +#define LP87565_PLL_MODE			0xC0
>>> +#define LP87565_EXT_CLK_FREQ			0x1F
>>> +
>>> +#define LP87565_EN_SPREAD_SPEC			BIT(7)
>>> +#define LP87565_EN_PIN_CTRL_GPIO3		BIT(6)
>>> +#define LP87565_EN_PIN_SELECT_GPIO3		BIT(5)
>>> +#define LP87565_EN_PIN_CTRL_GPIO2		BIT(4)
>>> +#define LP87565_EN_PIN_SELECT_GPIO2		BIT(3)
>>> +#define LP87565_GPIO3_SEL			BIT(2)
>>> +#define LP87565_GPIO2_SEL			BIT(1)
>>> +#define LP87565_GPIO1_SEL			BIT(0)
>>> +
>>> +#define LP87565_GOIO3_OD			BIT(6)
>>> +#define LP87565_GOIO2_OD			BIT(5)
>>> +#define LP87565_GOIO1_OD			BIT(4)
>>> +#define LP87565_GOIO3_DIR			BIT(2)
>>> +#define LP87565_GOIO2_DIR			BIT(1)
>>> +#define LP87565_GOIO1_DIR			BIT(0)
>>> +
>>> +#define LP87565_GOIO3_IN			BIT(2)
>>> +#define LP87565_GOIO2_IN			BIT(1)
>>> +#define LP87565_GOIO1_IN			BIT(0)
>>> +
>>> +#define LP87565_GOIO3_OUT			BIT(2)
>>> +#define LP87565_GOIO2_OUT			BIT(1)
>>> +#define LP87565_GOIO1_OUT			BIT(0)
>>> +
>>> +/* Number of step-down converters available */
>>> +#define LP87565_NUM_BUCK		6
>>> +
>>> +enum LP87565_regulator_id {
>>> +	/* BUCK's */
>>> +	LP87565_BUCK_0,
>>> +	LP87565_BUCK_1,
>>> +	LP87565_BUCK_2,
>>> +	LP87565_BUCK_3,
>>> +	LP87565_BUCK_10,
>>> +	LP87565_BUCK_23,
>>> +};
>>> +
>>> +/**
>>> + * struct LP87565 - state holder for the LP87565 driver
>>> + * @dev: struct device pointer for MFD device
>>> + * @rev: revision of the LP87565
>>> + * @dev_type: The device type for example lp87565-q1
>>> + * @lock: lock guarding the data structure
>>> + * @regmap: register map of the LP87565 PMIC
>>> + *
>>> + * Device data may be used to access the LP87565 chip
>>> + */
>>> +struct lp87565 {
>>> +	struct device *dev;
>>> +	u8 rev;
>>> +	u8 dev_type;
>>> +	struct regmap *regmap;
>>> +};
>>> +#endif /* __LINUX_MFD_LP87565_H */
>>
--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

  parent reply	other threads:[~2017-05-23  3:00 UTC|newest]

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2017-05-19 12:42 [PATCH 0/3] mfd: lp87565: Add lp87565 PMIC support Keerthy
2017-05-19 12:42 ` [PATCH 1/3] " Keerthy
     [not found]   ` <1495197739-17446-2-git-send-email-j-keerthy-l0cyMroinI0@public.gmane.org>
2017-05-19 15:42     ` Andrew F. Davis
     [not found]       ` <f6a16fe0-4212-bc73-090c-351b189ed864-l0cyMroinI0@public.gmane.org>
2017-05-22  4:23         ` Keerthy
2017-05-23  3:08           ` Keerthy
     [not found]             ` <f62f225b-931e-c68b-4e59-243c0c0b0d02-l0cyMroinI0@public.gmane.org>
2017-05-23  6:56               ` Lee Jones
2017-05-22 17:48     ` Lee Jones
2017-05-23  2:35       ` Keerthy
     [not found]         ` <26169872-1b43-88d1-3e5b-367b4d446222-l0cyMroinI0@public.gmane.org>
2017-05-23  3:00           ` Keerthy [this message]
2017-05-23  6:57           ` Lee Jones
2017-05-23  7:41             ` Keerthy
     [not found]               ` <a753fdb4-feb9-0894-6f40-a19d3f05714c-l0cyMroinI0@public.gmane.org>
2017-05-23  7:58                 ` Keerthy
2017-05-23  8:47                   ` Lee Jones
2017-05-23  9:53                     ` Keerthy
2017-05-23  8:45               ` Lee Jones
2017-05-23 10:11                 ` Keerthy
     [not found]                   ` <ce83f605-879b-dee0-d09e-63d01a7f66c7-l0cyMroinI0@public.gmane.org>
2017-05-23 12:21                     ` Keerthy
2017-05-23 15:39                     ` Lee Jones
     [not found] ` <1495197739-17446-1-git-send-email-j-keerthy-l0cyMroinI0@public.gmane.org>
2017-05-19 12:42   ` [PATCH 2/3] regulator: lp87565: Add support for lp87565 PMIC regulators Keerthy
     [not found]     ` <1495197739-17446-3-git-send-email-j-keerthy-l0cyMroinI0@public.gmane.org>
2017-05-19 15:53       ` Andrew F. Davis
     [not found]         ` <d7637719-a3f8-b711-f773-75ec5da8880b-l0cyMroinI0@public.gmane.org>
2017-05-22  4:28           ` Keerthy
2017-05-19 12:42   ` [PATCH 3/3] regulator: tps65917: Add support for SMPS12 Keerthy
2017-05-22 17:41     ` Lee Jones
2017-05-26 11:42     ` Applied "regulator: tps65917: Add support for SMPS12" to the regulator tree Mark Brown

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=4ae39bed-4004-c7d3-4e3e-3eeac98ca98f@ti.com \
    --to=j-keerthy-l0cymroini0@public.gmane.org \
    --cc=broonie-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    --cc=devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=lee.jones-QSEj5FYQhm4dnm+yROfE0A@public.gmane.org \
    --cc=linux-kernel-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=mark.rutland-5wv7dgnIgG8@public.gmane.org \
    --cc=robh+dt-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org \
    --cc=t-kristo-l0cyMroinI0@public.gmane.org \
    --cc=tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox