Re: Help needed USB hub disconnected at resume

[Igor Grinberg <grinberg@compulab.co.il>]

On 03/03/14 13:06, Roger Quadros wrote:
> Hi Marc,
> 
> On 03/03/2014 12:04 PM, Marc Murphy wrote:
>> Hi,
>> I am using the latest stable 3.4.80 kernel with some changes to get the EMAC Phy to initialise correctly after a suspend/resume.  The platform is AM3517 with most of the system working nice and smoothly. I have 1 issue though and need some advice/help to get the system to use the USB hub I have connected to the EHCI controller after a suspend to memory and resume.
>>
>> At boot all is recognised;
>>
>> [    1.486816] usbcore: registered new interface driver cdc_ether
>> [    1.493255] usbcore: registered new interface driver cdc_ncm
>> [    1.499450] usbcore: registered new interface driver qmi_wwan
>> [    1.506622] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
>> [    1.513580] ehci-omap.0 supply hsusb0 not found, using dummy regulator
>> [    2.521881] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
>> [    2.528411] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
>> [    2.536468] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
>> [    2.553070] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
>> [    2.559295] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
>> [    2.566436] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
>> [    2.574035] usb usb1: Product: OMAP-EHCI Host Controller
>> [    2.579620] usb usb1: Manufacturer: Linux 3.4.80 ehci_hcd
>> [    2.585296] usb usb1: SerialNumber: ehci-omap.0
>> [    2.591278] hub 1-0:1.0: USB hub found
>> [    2.595306] hub 1-0:1.0: 3 ports detected
>>
>> And I can see everything OK.
>>
>> # lsusb
>> Bus 001 Device 002: ID 0424:2513 Standard Microsystems Corp. 2.0 Hub
>> Bus 002 Device 002: ID 05e3:0718 Genesys Logic, Inc. IDE/SATA Adapter
>> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>> Bus 001 Device 003: ID 1199:68a2 Sierra Wireless, Inc.
>> #
>> #
>> # echo mem > /sys/power/state
>> [   73.736572] PM: Syncing filesystems ... done.
>> [   73.743530] Freezing user space processes ... (elapsed 0.01 seconds) done.
>> [   73.766784] Freezing remaining freezable tasks ... (elapsed 0.02 seconds) done.
>> [   73.959289] davinci_mdio davinci_mdio.0: timed out waiting for idle
>> [   73.968872] PM: suspend of devices complete after 170.410 msecs
>> [   73.975433] PM: late suspend of devices complete after 0.305 msecs
>> [   73.982635] PM: noirq suspend of devices complete after 0.732 msecs
>> [   83.430450] Powerdomain (core_pwrdm) didn't enter target state 1
>> [   83.436737] Could not enter target state in pm_suspend
>> [   83.443176] PM: noirq resume of devices complete after 0.915 msecs
>>  [   83.450164] PM: early resume of devices complete after 0.274 msecs
>> [   83.457336] <6>Waiting for PHY clock good...
>> [   83.463287] davinci_mdio davinci_mdio.0: resetting idled controller
>> [   83.471343] net eth0: attached PHY driver [SMSC LAN8710/LAN8720] (mii_bus:phy_addr=davinci_mdio-0:00, id=7c0f1)
>> [   84.771881] PM: resume of devices complete after 1315.185 msecs
>> [   84.778472] Restarting tasks ...
>> [   84.782379] usb 1-1: USB disconnect, device number 2
>> [   84.790557] done.
>> [   84.792938] mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz
>> sh: write error:[   84.800781] usb 1-1.1: USB disconnect, device number 3
>>  Operation not p[   84.808349] qmi_wwan 1-1.1:1.8: wwan0: unregister 'qmi_wwan' usb-ehci-omap.0-1.1, Sierra Wireless wwan/QMI device
>> ermitted
>> [   84.859191] mmc1: mmc_rescan_try_freq: trying to init card at 400000 Hz
>> [   86.490356] PHY: davinci_mdio-0:00 - Link is Up - 100/Full
>> #
>> #
>> # lsusb
>> Bus 002 Device 002: ID 05e3:0718 Genesys Logic, Inc. IDE/SATA Adapter
>> Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>> Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
>> #
>>
>> Is there any relevant patch out there that would address the issue that I see ?
> 
> Does this happen because of OFF mode?
> Can you please try the tests with off mode disabled?
> 
> e.g.
> mount -t debugfs none /sys/kernel/debug
> echo 0 > /sys/kernel/debug/pm_debug/enable_off_mode
> suspend & resume

AFAIK, AM3517 does not have OFF mode.
We had something similar with runtime pm...
It might be useful to know which hub is this and how is it connected...

> 
> Also please send the output of /sys/kernel/debug/pm_debug/count
> before suspend and after resume. Thanks.



-- 
Regards,
Igor.