* [PATCH 0/3] Support for OMAP3 Zoom2 board @ 2009-05-07 21:42 Mikkel Christensen 2009-05-07 21:42 ` [PATCH 1/3] OMAP3:zoom2: Add support " Mikkel Christensen 2009-05-13 17:53 ` [PATCH 0/3] Support " Pandita, Vikram 0 siblings, 2 replies; 6+ messages in thread From: Mikkel Christensen @ 2009-05-07 21:42 UTC (permalink / raw) To: linux-omap; +Cc: Mikkel Christensen The following patch series adds support for Zoom2 board. The board has: - Modem attached to UART1 - WLAN attached to UART2 - GPS attached to UART3 An external debug board is included for console and LAN. For details refer to this site: http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp Future work: - SMSC911x NFS mount problem - Low level debug uart need to use debug board - Dynamic detection of debug board presence TI wiki with FAQs on getting this board booting: https://omapzoom.org/gf/project/omapzoom/wiki/?pagename=GettingStartedWithZoomII_AKA_OMAP34XII_MDP ^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 1/3] OMAP3:zoom2: Add support for OMAP3 Zoom2 board 2009-05-07 21:42 [PATCH 0/3] Support for OMAP3 Zoom2 board Mikkel Christensen @ 2009-05-07 21:42 ` Mikkel Christensen 2009-05-07 21:42 ` [PATCH 2/3] OMAP3:zoom2: Defconfig for " Mikkel Christensen 2009-05-13 18:44 ` [PATCH 1/3] OMAP3:zoom2: Add support for OMAP3 " Kevin Hilman 2009-05-13 17:53 ` [PATCH 0/3] Support " Pandita, Vikram 1 sibling, 2 replies; 6+ messages in thread From: Mikkel Christensen @ 2009-05-07 21:42 UTC (permalink / raw) To: linux-omap; +Cc: Mikkel Christensen, Vikram Pandita This patch creates the minimal OMAP3 Zoom2 board support. Signed-off-by: Mikkel Christensen <mlc@ti.com> Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/mach-omap2/board-zoom2-debugboard.c | 150 ++++++++++++++++++++++++++ arch/arm/mach-omap2/board-zoom2.c | 126 +++++++++++++++++++++ 2 files changed, 276 insertions(+), 0 deletions(-) create mode 100644 arch/arm/mach-omap2/board-zoom2-debugboard.c create mode 100644 arch/arm/mach-omap2/board-zoom2.c diff --git a/arch/arm/mach-omap2/board-zoom2-debugboard.c b/arch/arm/mach-omap2/board-zoom2-debugboard.c new file mode 100644 index 0000000..ae90f2b --- /dev/null +++ b/arch/arm/mach-omap2/board-zoom2-debugboard.c @@ -0,0 +1,150 @@ +/* + * arch/arm/mach-omap2/board-zoom2-debugboard.c + * + * OMAP3 Zoom2 debug board support. + * + * Copyright (C) 2009 Texas Instruments Inc. + * Mikkel Christensen <mlc@ti.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/delay.h> +#include <linux/serial_8250.h> +#include <linux/serial_reg.h> +#include <linux/smsc911x.h> +#include <linux/io.h> + +#include <mach/common.h> +#include <mach/board.h> +#include <mach/gpio.h> +#include <mach/gpmc.h> + +#define ZOOM2_SMSC911X_CS 7 +#define ZOOM2_SMSC911X_GPIO 158 +#define ZOOM2_QUADUART_CS 3 +#define ZOOM2_QUADUART_GPIO 102 +#define QUART_CLK 1843200 +#define DEBUG_BASE 0x08000000 +#define ZOOM2_ETHR_START DEBUG_BASE + +static struct resource zoom2_smsc911x_resources[] = { + [0] = { + .start = ZOOM2_ETHR_START, + .end = ZOOM2_ETHR_START + SZ_4K, + .flags = IORESOURCE_MEM, + }, + [1] = { + .start = 0, + .end = 0, + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, + }, +}; + +static struct smsc911x_platform_config zoom2_smsc911x_config = { + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, + .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, + .flags = SMSC911X_USE_32BIT, + .phy_interface = PHY_INTERFACE_MODE_MII, +}; + +static struct platform_device zoom2_smsc911x_device = { + .name = "smsc911x", + .id = -1, + .num_resources = ARRAY_SIZE(zoom2_smsc911x_resources), + .resource = zoom2_smsc911x_resources, + .dev = { + .platform_data = &zoom2_smsc911x_config, + }, +}; + +static inline void __init zoom2_init_smsc911x(void) +{ + int eth_cs; + unsigned long cs_mem_base; + int eth_gpio = 0; + + eth_cs = ZOOM2_SMSC911X_CS; + + if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) { + printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n"); + return; + } + + zoom2_smsc911x_resources[0].start = cs_mem_base + 0x0; + zoom2_smsc911x_resources[0].end = cs_mem_base + 0xff; + udelay(100); + + eth_gpio = ZOOM2_SMSC911X_GPIO; + + zoom2_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio); + + if (gpio_request(eth_gpio, "smsc911x irq") < 0) { + printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", + eth_gpio); + return; + } + gpio_direction_input(eth_gpio); +} + +static struct plat_serial8250_port serial_platform_data[] = { + { + .membase = 0, + .mapbase = 0x10000000, + .irq = OMAP_GPIO_IRQ(102), + .flags = UPF_BOOT_AUTOCONF|UPF_IOREMAP|UPF_SHARE_IRQ, + .iotype = UPIO_MEM, + .regshift = 1, + .uartclk = QUART_CLK, + }, { + .flags = 0 + } +}; + +static struct platform_device zoom2_debugboard_serial_device = { + .name = "serial8250", + .id = PLAT8250_DEV_PLATFORM1, + .dev = { + .platform_data = serial_platform_data, + }, +}; + +static inline void __init zoom2_init_quaduart(void) +{ + int quart_cs; + unsigned long cs_mem_base; + int quart_gpio = 0; + + quart_cs = ZOOM2_QUADUART_CS; + + if (gpmc_cs_request(quart_cs, SZ_1M, &cs_mem_base) < 0) { + printk(KERN_ERR "Failed to request GPMC mem" + "for Quad UART(TL16CP754C)\n"); + return; + } + + quart_gpio = ZOOM2_QUADUART_GPIO; + + if (gpio_request(quart_gpio, "TL16CP754C GPIO") < 0) { + printk(KERN_ERR "Failed to request GPIO%d for TL16CP754C\n", + quart_gpio); + return; + } + gpio_direction_input(quart_gpio); +} + +static struct platform_device *zoom2_devices[] __initdata = { + &zoom2_smsc911x_device, + &zoom2_debugboard_serial_device, +}; + +static int __init omap_zoom2_debugboard_init(void) +{ + zoom2_init_smsc911x(); + zoom2_init_quaduart(); + return platform_add_devices(zoom2_devices, ARRAY_SIZE(zoom2_devices)); +} +arch_initcall(omap_zoom2_debugboard_init); diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c new file mode 100644 index 0000000..f43809a --- /dev/null +++ b/arch/arm/mach-omap2/board-zoom2.c @@ -0,0 +1,126 @@ +/* + * linux/arch/arm/mach-omap2/board-zoom2.c + * + * Copyright (C) 2009 Texas Instruments Inc. + * Mikkel Christensen <mlc@ti.com> + * + * Modified from mach-omap2/board-ldp.c + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/platform_device.h> +#include <linux/delay.h> +#include <linux/input.h> +#include <linux/workqueue.h> +#include <linux/err.h> +#include <linux/clk.h> +#include <linux/spi/spi.h> +#include <linux/spi/ads7846.h> +#include <linux/i2c/twl4030.h> +#include <linux/serial_8250.h> +#include <linux/io.h> + +#include <mach/hardware.h> +#include <asm/mach-types.h> +#include <asm/mach/arch.h> +#include <asm/mach/map.h> + +#include <mach/mcspi.h> +#include <mach/gpio.h> +#include <mach/board.h> +#include <mach/common.h> +#include <mach/gpmc.h> + +#include <asm/delay.h> +#include <mach/control.h> +#include <mach/usb.h> + +#include "mmc-twl4030.h" + +static void __init omap_zoom2_init_irq(void) +{ + omap2_init_common_hw(NULL); + omap_init_irq(); + omap_gpio_init(); +} + +static struct omap_uart_config zoom2_uart_config __initdata = { + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), +}; + +static struct omap_board_config_kernel zoom2_config[] __initdata = { + { OMAP_TAG_UART, &zoom2_uart_config }, +}; + +static struct twl4030_gpio_platform_data zoom2_gpio_data = { + .gpio_base = OMAP_MAX_GPIO_LINES, + .irq_base = TWL4030_GPIO_IRQ_BASE, + .irq_end = TWL4030_GPIO_IRQ_END, +}; + +static struct twl4030_platform_data zoom2_twldata = { + .irq_base = TWL4030_IRQ_BASE, + .irq_end = TWL4030_IRQ_END, + + /* platform_data for children goes here */ + .gpio = &zoom2_gpio_data, +}; + +static struct i2c_board_info __initdata zoom2_i2c_boardinfo[] = { + { + I2C_BOARD_INFO("twl4030", 0x48), + .flags = I2C_CLIENT_WAKE, + .irq = INT_34XX_SYS_NIRQ, + .platform_data = &zoom2_twldata, + }, +}; + +static int __init omap_i2c_init(void) +{ + omap_register_i2c_bus(1, 2600, zoom2_i2c_boardinfo, + ARRAY_SIZE(zoom2_i2c_boardinfo)); + omap_register_i2c_bus(2, 400, NULL, 0); + omap_register_i2c_bus(3, 400, NULL, 0); + return 0; +} + +static struct twl4030_hsmmc_info mmc[] __initdata = { + { + .mmc = 1, + .wires = 4, + .gpio_cd = -EINVAL, + .gpio_wp = -EINVAL, + }, + {} /* Terminator */ +}; + +static void __init omap_zoom2_init(void) +{ + omap_i2c_init(); + omap_board_config = zoom2_config; + omap_board_config_size = ARRAY_SIZE(zoom2_config); + omap_serial_init(); + twl4030_mmc_init(mmc); + usb_musb_init(); +} + +static void __init omap_zoom2_map_io(void) +{ + omap2_set_globals_343x(); + omap2_map_common_io(); +} + +MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board") + .phys_io = 0x48000000, + .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc, + .boot_params = 0x80000100, + .map_io = omap_zoom2_map_io, + .init_irq = omap_zoom2_init_irq, + .init_machine = omap_zoom2_init, + .timer = &omap_timer, +MACHINE_END -- 1.5.4.3 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 2/3] OMAP3:zoom2: Defconfig for Zoom2 board 2009-05-07 21:42 ` [PATCH 1/3] OMAP3:zoom2: Add support " Mikkel Christensen @ 2009-05-07 21:42 ` Mikkel Christensen 2009-05-07 21:42 ` [PATCH 3/3] OMAP3:zoom2: Makefile and Kconfig " Mikkel Christensen 2009-05-13 18:44 ` [PATCH 1/3] OMAP3:zoom2: Add support for OMAP3 " Kevin Hilman 1 sibling, 1 reply; 6+ messages in thread From: Mikkel Christensen @ 2009-05-07 21:42 UTC (permalink / raw) To: linux-omap; +Cc: Mikkel Christensen, Vikram Pandita This patch adds OMAP3 Zoom2 board defconfig. Signed-off-by: Mikkel Christensen <mlc@ti.com> Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/configs/omap3_zoom2_defconfig | 1211 ++++++++++++++++++++++++++++++++ 1 files changed, 1211 insertions(+), 0 deletions(-) create mode 100644 arch/arm/configs/omap3_zoom2_defconfig diff --git a/arch/arm/configs/omap3_zoom2_defconfig b/arch/arm/configs/omap3_zoom2_defconfig new file mode 100644 index 0000000..213fe9c --- /dev/null +++ b/arch/arm/configs/omap3_zoom2_defconfig @@ -0,0 +1,1211 @@ +# +# Automatically generated make config: don't edit +# Linux kernel version: 2.6.27-rc5 +# Fri Oct 10 11:49:41 2008 +# +CONFIG_ARM=y +CONFIG_SYS_SUPPORTS_APM_EMULATION=y +CONFIG_GENERIC_GPIO=y +CONFIG_GENERIC_TIME=y +CONFIG_GENERIC_CLOCKEVENTS=y +CONFIG_MMU=y +# CONFIG_NO_IOPORT is not set +CONFIG_GENERIC_HARDIRQS=y +CONFIG_STACKTRACE_SUPPORT=y +CONFIG_HAVE_LATENCYTOP_SUPPORT=y +CONFIG_LOCKDEP_SUPPORT=y +CONFIG_TRACE_IRQFLAGS_SUPPORT=y +CONFIG_HARDIRQS_SW_RESEND=y +CONFIG_GENERIC_IRQ_PROBE=y +CONFIG_RWSEM_GENERIC_SPINLOCK=y +# CONFIG_ARCH_HAS_ILOG2_U32 is not set +# CONFIG_ARCH_HAS_ILOG2_U64 is not set +CONFIG_GENERIC_HWEIGHT=y +CONFIG_GENERIC_CALIBRATE_DELAY=y +CONFIG_ARCH_SUPPORTS_AOUT=y +CONFIG_ZONE_DMA=y +CONFIG_GENERIC_HARDIRQS_NO__DO_IRQ=y +CONFIG_VECTORS_BASE=0xffff0000 +CONFIG_DEFCONFIG_LIST="/lib/modules/$UNAME_RELEASE/.config" + +# +# General setup +# +CONFIG_EXPERIMENTAL=y +CONFIG_BROKEN_ON_SMP=y +CONFIG_INIT_ENV_ARG_LIMIT=32 +CONFIG_LOCALVERSION="" +CONFIG_LOCALVERSION_AUTO=y +CONFIG_SWAP=y +CONFIG_SYSVIPC=y +CONFIG_SYSVIPC_SYSCTL=y +CONFIG_BSD_PROCESS_ACCT=y +# CONFIG_BSD_PROCESS_ACCT_V3 is not set +# CONFIG_IKCONFIG is not set +CONFIG_LOG_BUF_SHIFT=14 +# CONFIG_CGROUPS is not set +CONFIG_GROUP_SCHED=y +CONFIG_FAIR_GROUP_SCHED=y +# CONFIG_RT_GROUP_SCHED is not set +CONFIG_USER_SCHED=y +# CONFIG_CGROUP_SCHED is not set +CONFIG_SYSFS_DEPRECATED=y +CONFIG_SYSFS_DEPRECATED_V2=y +# CONFIG_RELAY is not set +# CONFIG_NAMESPACES is not set +CONFIG_BLK_DEV_INITRD=y +CONFIG_INITRAMFS_SOURCE="" +CONFIG_CC_OPTIMIZE_FOR_SIZE=y +CONFIG_SYSCTL=y +CONFIG_EMBEDDED=y +CONFIG_UID16=y +# CONFIG_SYSCTL_SYSCALL is not set +CONFIG_KALLSYMS=y +# CONFIG_KALLSYMS_ALL is not set +CONFIG_KALLSYMS_EXTRA_PASS=y +CONFIG_HOTPLUG=y +CONFIG_PRINTK=y +CONFIG_BUG=y +CONFIG_ELF_CORE=y +CONFIG_COMPAT_BRK=y +CONFIG_BASE_FULL=y +CONFIG_FUTEX=y +CONFIG_ANON_INODES=y +CONFIG_EPOLL=y +CONFIG_SIGNALFD=y +CONFIG_TIMERFD=y +CONFIG_EVENTFD=y +CONFIG_SHMEM=y +CONFIG_VM_EVENT_COUNTERS=y +CONFIG_SLAB=y +# CONFIG_SLUB is not set +# CONFIG_SLOB is not set +# CONFIG_PROFILING is not set +# CONFIG_MARKERS is not set +CONFIG_HAVE_OPROFILE=y +# CONFIG_KPROBES is not set +# CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS is not set +# CONFIG_HAVE_IOREMAP_PROT is not set +CONFIG_HAVE_KPROBES=y +CONFIG_HAVE_KRETPROBES=y +# CONFIG_HAVE_ARCH_TRACEHOOK is not set +# CONFIG_HAVE_DMA_ATTRS is not set +# CONFIG_USE_GENERIC_SMP_HELPERS is not set +CONFIG_HAVE_CLK=y +CONFIG_PROC_PAGE_MONITOR=y +CONFIG_HAVE_GENERIC_DMA_COHERENT=y +CONFIG_SLABINFO=y +CONFIG_RT_MUTEXES=y +# CONFIG_TINY_SHMEM is not set +CONFIG_BASE_SMALL=0 +CONFIG_MODULES=y +# CONFIG_MODULE_FORCE_LOAD is not set +CONFIG_MODULE_UNLOAD=y +# CONFIG_MODULE_FORCE_UNLOAD is not set +CONFIG_MODVERSIONS=y +CONFIG_MODULE_SRCVERSION_ALL=y +CONFIG_KMOD=y +CONFIG_BLOCK=y +# CONFIG_LBD is not set +# CONFIG_BLK_DEV_IO_TRACE is not set +# CONFIG_LSF is not set +# CONFIG_BLK_DEV_BSG is not set +# CONFIG_BLK_DEV_INTEGRITY is not set + +# +# IO Schedulers +# +CONFIG_IOSCHED_NOOP=y +CONFIG_IOSCHED_AS=y +CONFIG_IOSCHED_DEADLINE=y +CONFIG_IOSCHED_CFQ=y +CONFIG_DEFAULT_AS=y +# CONFIG_DEFAULT_DEADLINE is not set +# CONFIG_DEFAULT_CFQ is not set +# CONFIG_DEFAULT_NOOP is not set +CONFIG_DEFAULT_IOSCHED="anticipatory" +CONFIG_CLASSIC_RCU=y + +# +# System Type +# +# CONFIG_ARCH_AAEC2000 is not set +# CONFIG_ARCH_INTEGRATOR is not set +# CONFIG_ARCH_REALVIEW is not set +# CONFIG_ARCH_VERSATILE is not set +# CONFIG_ARCH_AT91 is not set +# CONFIG_ARCH_CLPS7500 is not set +# CONFIG_ARCH_CLPS711X is not set +# CONFIG_ARCH_EBSA110 is not set +# CONFIG_ARCH_EP93XX is not set +# CONFIG_ARCH_FOOTBRIDGE is not set +# CONFIG_ARCH_NETX is not set +# CONFIG_ARCH_H720X is not set +# CONFIG_ARCH_IMX is not set +# CONFIG_ARCH_IOP13XX is not set +# CONFIG_ARCH_IOP32X is not set +# CONFIG_ARCH_IOP33X is not set +# CONFIG_ARCH_IXP23XX is not set +# CONFIG_ARCH_IXP2000 is not set +# CONFIG_ARCH_IXP4XX is not set +# CONFIG_ARCH_L7200 is not set +# CONFIG_ARCH_KIRKWOOD is not set +# CONFIG_ARCH_KS8695 is not set +# CONFIG_ARCH_NS9XXX is not set +# CONFIG_ARCH_LOKI is not set +# CONFIG_ARCH_MV78XX0 is not set +# CONFIG_ARCH_MXC is not set +# CONFIG_ARCH_ORION5X is not set +# CONFIG_ARCH_PNX4008 is not set +# CONFIG_ARCH_PXA is not set +# CONFIG_ARCH_RPC is not set +# CONFIG_ARCH_SA1100 is not set +# CONFIG_ARCH_S3C2410 is not set +# CONFIG_ARCH_SHARK is not set +# CONFIG_ARCH_LH7A40X is not set +# CONFIG_ARCH_DAVINCI is not set +CONFIG_ARCH_OMAP=y +# CONFIG_ARCH_MSM7X00A is not set + +# +# TI OMAP Implementations +# +CONFIG_ARCH_OMAP_OTG=y +# CONFIG_ARCH_OMAP1 is not set +# CONFIG_ARCH_OMAP2 is not set +CONFIG_ARCH_OMAP3=y + +# +# OMAP Feature Selections +# +# CONFIG_OMAP_DEBUG_POWERDOMAIN is not set +# CONFIG_OMAP_DEBUG_CLOCKDOMAIN is not set +# CONFIG_OMAP_RESET_CLOCKS is not set +CONFIG_OMAP_MUX=y +CONFIG_OMAP_MUX_DEBUG=y +CONFIG_OMAP_MUX_WARNINGS=y +CONFIG_OMAP_MCBSP=y +# CONFIG_OMAP_MPU_TIMER is not set +CONFIG_OMAP_32K_TIMER=y +CONFIG_OMAP_32K_TIMER_HZ=128 +CONFIG_OMAP_DM_TIMER=y +# CONFIG_OMAP_LL_DEBUG_UART1 is not set +# CONFIG_OMAP_LL_DEBUG_UART2 is not set +CONFIG_OMAP_LL_DEBUG_UART3=y +CONFIG_OMAP_SERIAL_WAKE=y +CONFIG_ARCH_OMAP34XX=y +CONFIG_ARCH_OMAP3430=y + +# +# OMAP Board Type +# +# CONFIG_MACH_OMAP3_BEAGLE is not set +# CONFIG_MACH_OMAP_LDP is not set +CONFIG_MACH_OMAP_ZOOM2=y +# CONFIG_MACH_OVERO is not set + +# +# Boot options +# + +# +# Power management +# + +# +# Processor Type +# +CONFIG_CPU_32=y +CONFIG_CPU_32v6K=y +CONFIG_CPU_V7=y +CONFIG_CPU_32v7=y +CONFIG_CPU_ABRT_EV7=y +CONFIG_CPU_PABRT_IFAR=y +CONFIG_CPU_CACHE_V7=y +CONFIG_CPU_CACHE_VIPT=y +CONFIG_CPU_COPY_V6=y +CONFIG_CPU_TLB_V7=y +CONFIG_CPU_HAS_ASID=y +CONFIG_CPU_CP15=y +CONFIG_CPU_CP15_MMU=y + +# +# Processor Features +# +CONFIG_ARM_THUMB=y +# CONFIG_ARM_THUMBEE is not set +# CONFIG_CPU_ICACHE_DISABLE is not set +# CONFIG_CPU_DCACHE_DISABLE is not set +# CONFIG_CPU_BPREDICT_DISABLE is not set +CONFIG_HAS_TLS_REG=y +# CONFIG_OUTER_CACHE is not set + +# +# Bus support +# +# CONFIG_PCI_SYSCALL is not set +# CONFIG_ARCH_SUPPORTS_MSI is not set +# CONFIG_PCCARD is not set + +# +# Kernel Features +# +CONFIG_TICK_ONESHOT=y +CONFIG_NO_HZ=y +CONFIG_HIGH_RES_TIMERS=y +CONFIG_GENERIC_CLOCKEVENTS_BUILD=y +# CONFIG_PREEMPT is not set +CONFIG_HZ=128 +CONFIG_AEABI=y +CONFIG_OABI_COMPAT=y +CONFIG_ARCH_FLATMEM_HAS_HOLES=y +# CONFIG_ARCH_DISCONTIGMEM_ENABLE is not set +CONFIG_SELECT_MEMORY_MODEL=y +CONFIG_FLATMEM_MANUAL=y +# CONFIG_DISCONTIGMEM_MANUAL is not set +# CONFIG_SPARSEMEM_MANUAL is not set +CONFIG_FLATMEM=y +CONFIG_FLAT_NODE_MEM_MAP=y +# CONFIG_SPARSEMEM_STATIC is not set +# CONFIG_SPARSEMEM_VMEMMAP_ENABLE is not set +CONFIG_PAGEFLAGS_EXTENDED=y +CONFIG_SPLIT_PTLOCK_CPUS=4 +# CONFIG_RESOURCES_64BIT is not set +CONFIG_ZONE_DMA_FLAG=1 +CONFIG_BOUNCE=y +CONFIG_VIRT_TO_BUS=y +# CONFIG_LEDS is not set +CONFIG_ALIGNMENT_TRAP=y + +# +# Boot options +# +CONFIG_ZBOOT_ROM_TEXT=0x0 +CONFIG_ZBOOT_ROM_BSS=0x0 +CONFIG_CMDLINE="root=/dev/nfs nfsroot=192.168.0.1:/home/user/buildroot ip=192.168.0.2:192.168.0.1:192.168.0.1:255.255.255.0:tgt:eth0:off rw console=ttyS2,115200n8" +# CONFIG_XIP_KERNEL is not set +# CONFIG_KEXEC is not set + +# +# CPU Frequency scaling +# +# CONFIG_CPU_FREQ is not set + +# +# Floating point emulation +# + +# +# At least one emulation must be selected +# +CONFIG_FPE_NWFPE=y +# CONFIG_FPE_NWFPE_XP is not set +# CONFIG_FPE_FASTFPE is not set +CONFIG_VFP=y +CONFIG_VFPv3=y +# CONFIG_NEON is not set + +# +# Userspace binary formats +# +CONFIG_BINFMT_ELF=y +# CONFIG_BINFMT_AOUT is not set +CONFIG_BINFMT_MISC=y + +# +# Power management options +# +# CONFIG_PM is not set +CONFIG_ARCH_SUSPEND_POSSIBLE=y +CONFIG_NET=y + +# +# Networking options +# +CONFIG_PACKET=y +# CONFIG_PACKET_MMAP is not set +CONFIG_UNIX=y +CONFIG_XFRM=y +CONFIG_XFRM_USER=y +# CONFIG_XFRM_SUB_POLICY is not set +CONFIG_XFRM_MIGRATE=y +# CONFIG_XFRM_STATISTICS is not set +CONFIG_NET_KEY=y +CONFIG_NET_KEY_MIGRATE=y +CONFIG_INET=y +CONFIG_IP_MULTICAST=y +# CONFIG_IP_ADVANCED_ROUTER is not set +CONFIG_IP_FIB_HASH=y +CONFIG_IP_PNP=y +CONFIG_IP_PNP_DHCP=y +CONFIG_IP_PNP_BOOTP=y +CONFIG_IP_PNP_RARP=y +# CONFIG_NET_IPIP is not set +# CONFIG_NET_IPGRE is not set +# CONFIG_IP_MROUTE is not set +# CONFIG_ARPD is not set +# CONFIG_SYN_COOKIES is not set +# CONFIG_INET_AH is not set +# CONFIG_INET_ESP is not set +# CONFIG_INET_IPCOMP is not set +# CONFIG_INET_XFRM_TUNNEL is not set +# CONFIG_INET_TUNNEL is not set +CONFIG_INET_XFRM_MODE_TRANSPORT=y +CONFIG_INET_XFRM_MODE_TUNNEL=y +CONFIG_INET_XFRM_MODE_BEET=y +# CONFIG_INET_LRO is not set +CONFIG_INET_DIAG=y +CONFIG_INET_TCP_DIAG=y +# CONFIG_TCP_CONG_ADVANCED is not set +CONFIG_TCP_CONG_CUBIC=y +CONFIG_DEFAULT_TCP_CONG="cubic" +# CONFIG_TCP_MD5SIG is not set +# CONFIG_IPV6 is not set +# CONFIG_NETWORK_SECMARK is not set +# CONFIG_NETFILTER is not set +# CONFIG_IP_DCCP is not set +# CONFIG_IP_SCTP is not set +# CONFIG_TIPC is not set +# CONFIG_ATM is not set +# CONFIG_BRIDGE is not set +# CONFIG_NET_DSA is not set +# CONFIG_VLAN_8021Q is not set +# CONFIG_DECNET is not set +# CONFIG_LLC2 is not set +# CONFIG_IPX is not set +# CONFIG_ATALK is not set +# CONFIG_X25 is not set +# CONFIG_LAPB is not set +# CONFIG_ECONET is not set +# CONFIG_WAN_ROUTER is not set +# CONFIG_NET_SCHED is not set + +# +# Network testing +# +# CONFIG_NET_PKTGEN is not set +# CONFIG_HAMRADIO is not set +# CONFIG_CAN is not set +# CONFIG_IRDA is not set +# CONFIG_BT is not set +# CONFIG_AF_RXRPC is not set +# CONFIG_PHONET is not set +# CONFIG_WIRELESS is not set +# CONFIG_RFKILL is not set +# CONFIG_NET_9P is not set + +# +# Device Drivers +# + +# +# Generic Driver Options +# +CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug" +CONFIG_STANDALONE=y +CONFIG_PREVENT_FIRMWARE_BUILD=y +# CONFIG_FW_LOADER is not set +# CONFIG_DEBUG_DRIVER is not set +# CONFIG_DEBUG_DEVRES is not set +# CONFIG_SYS_HYPERVISOR is not set +CONFIG_CONNECTOR=y +CONFIG_PROC_EVENTS=y +# CONFIG_MTD is not set +# CONFIG_PARPORT is not set +CONFIG_BLK_DEV=y +# CONFIG_BLK_DEV_COW_COMMON is not set +CONFIG_BLK_DEV_LOOP=y +# CONFIG_BLK_DEV_CRYPTOLOOP is not set +CONFIG_BLK_DEV_RAM=y +CONFIG_BLK_DEV_RAM_COUNT=16 +CONFIG_BLK_DEV_RAM_SIZE=16384 +# CONFIG_BLK_DEV_XIP is not set +# CONFIG_CDROM_PKTCDVD is not set +CONFIG_MISC_DEVICES=y +# CONFIG_EEPROM_93CX6 is not set +# CONFIG_ENCLOSURE_SERVICES is not set +CONFIG_HAVE_IDE=y +# CONFIG_IDE is not set + +# +# SCSI device support +# +# CONFIG_RAID_ATTRS is not set +CONFIG_SCSI=y +CONFIG_SCSI_DMA=y +# CONFIG_SCSI_TGT is not set +# CONFIG_SCSI_NETLINK is not set +CONFIG_SCSI_PROC_FS=y + +# +# SCSI support type (disk, tape, CD-ROM) +# +CONFIG_BLK_DEV_SD=y +# CONFIG_CHR_DEV_ST is not set +# CONFIG_CHR_DEV_OSST is not set +# CONFIG_BLK_DEV_SR is not set +# CONFIG_CHR_DEV_SG is not set +# CONFIG_CHR_DEV_SCH is not set + +# +# Some SCSI devices (e.g. CD jukebox) support multiple LUNs +# +# CONFIG_SCSI_MULTI_LUN is not set +# CONFIG_SCSI_CONSTANTS is not set +# CONFIG_SCSI_LOGGING is not set +# CONFIG_SCSI_SCAN_ASYNC is not set +CONFIG_SCSI_WAIT_SCAN=m + +# +# SCSI Transports +# +# CONFIG_SCSI_SPI_ATTRS is not set +# CONFIG_SCSI_FC_ATTRS is not set +# CONFIG_SCSI_SAS_LIBSAS is not set +# CONFIG_SCSI_SRP_ATTRS is not set +CONFIG_SCSI_LOWLEVEL=y +# CONFIG_SCSI_DEBUG is not set +# CONFIG_SCSI_DH is not set +# CONFIG_ATA is not set +# CONFIG_MD is not set +CONFIG_NETDEVICES=y +# CONFIG_DUMMY is not set +# CONFIG_BONDING is not set +# CONFIG_MACVLAN is not set +# CONFIG_EQUALIZER is not set +# CONFIG_TUN is not set +# CONFIG_VETH is not set +CONFIG_PHYLIB=y + +# +# MII PHY device drivers +# +# CONFIG_MARVELL_PHY is not set +# CONFIG_DAVICOM_PHY is not set +# CONFIG_QSEMI_PHY is not set +# CONFIG_LXT_PHY is not set +# CONFIG_CICADA_PHY is not set +# CONFIG_VITESSE_PHY is not set +CONFIG_SMSC_PHY=y +# CONFIG_BROADCOM_PHY is not set +# CONFIG_ICPLUS_PHY is not set +# CONFIG_REALTEK_PHY is not set +# CONFIG_NATIONAL_PHY is not set +# CONFIG_STE10XP is not set +# CONFIG_LSI_ET1011C_PHY is not set +# CONFIG_FIXED_PHY is not set +# CONFIG_MDIO_BITBANG is not set +CONFIG_NET_ETHERNET=y +CONFIG_MII=y +# CONFIG_AX88796 is not set +# CONFIG_SMC91X is not set +# CONFIG_DM9000 is not set +# CONFIG_ENC28J60 is not set +# CONFIG_SMC911X is not set +CONFIG_SMSC911X=y +# CONFIG_IBM_NEW_EMAC_ZMII is not set +# CONFIG_IBM_NEW_EMAC_RGMII is not set +# CONFIG_IBM_NEW_EMAC_TAH is not set +# CONFIG_IBM_NEW_EMAC_EMAC4 is not set +# CONFIG_IBM_NEW_EMAC_NO_FLOW_CTRL is not set +# CONFIG_IBM_NEW_EMAC_MAL_CLR_ICINTSTAT is not set +# CONFIG_IBM_NEW_EMAC_MAL_COMMON_ERR is not set +# CONFIG_B44 is not set +CONFIG_NETDEV_1000=y +CONFIG_NETDEV_10000=y + +# +# Wireless LAN +# +# CONFIG_WLAN_PRE80211 is not set +# CONFIG_WLAN_80211 is not set +# CONFIG_IWLWIFI_LEDS is not set + +# +# USB Network Adapters +# +# CONFIG_USB_CATC is not set +# CONFIG_USB_KAWETH is not set +# CONFIG_USB_PEGASUS is not set +# CONFIG_USB_RTL8150 is not set +# CONFIG_USB_USBNET is not set +# CONFIG_WAN is not set +# CONFIG_PPP is not set +# CONFIG_SLIP is not set +# CONFIG_NETCONSOLE is not set +# CONFIG_NETPOLL is not set +# CONFIG_NET_POLL_CONTROLLER is not set +# CONFIG_ISDN is not set + +# +# Input device support +# +CONFIG_INPUT=y +# CONFIG_INPUT_FF_MEMLESS is not set +# CONFIG_INPUT_POLLDEV is not set + +# +# Userland interfaces +# +# CONFIG_INPUT_MOUSEDEV is not set +# CONFIG_INPUT_JOYDEV is not set +CONFIG_INPUT_EVDEV=y +# CONFIG_INPUT_EVBUG is not set + +# +# Input Device Drivers +# +# CONFIG_INPUT_KEYBOARD is not set +# CONFIG_INPUT_MOUSE is not set +# CONFIG_INPUT_JOYSTICK is not set +# CONFIG_INPUT_TABLET is not set +CONFIG_INPUT_TOUCHSCREEN=y +CONFIG_TOUCHSCREEN_ADS7846=y +# CONFIG_TOUCHSCREEN_FUJITSU is not set +# CONFIG_TOUCHSCREEN_GUNZE is not set +# CONFIG_TOUCHSCREEN_ELO is not set +# CONFIG_TOUCHSCREEN_MTOUCH is not set +# CONFIG_TOUCHSCREEN_INEXIO is not set +# CONFIG_TOUCHSCREEN_MK712 is not set +# CONFIG_TOUCHSCREEN_PENMOUNT is not set +# CONFIG_TOUCHSCREEN_TOUCHRIGHT is not set +# CONFIG_TOUCHSCREEN_TOUCHWIN is not set +# CONFIG_TOUCHSCREEN_UCB1400 is not set +# CONFIG_TOUCHSCREEN_TOUCHIT213 is not set +# CONFIG_INPUT_MISC is not set + +# +# Hardware I/O ports +# +# CONFIG_SERIO is not set +# CONFIG_GAMEPORT is not set + +# +# Character devices +# +CONFIG_VT=y +CONFIG_CONSOLE_TRANSLATIONS=y +CONFIG_VT_CONSOLE=y +CONFIG_HW_CONSOLE=y +# CONFIG_VT_HW_CONSOLE_BINDING is not set +CONFIG_DEVKMEM=y +# CONFIG_SERIAL_NONSTANDARD is not set + +# +# Serial drivers +# +CONFIG_SERIAL_8250=y +CONFIG_SERIAL_8250_CONSOLE=y +CONFIG_SERIAL_8250_NR_UARTS=32 +CONFIG_SERIAL_8250_RUNTIME_UARTS=4 +CONFIG_SERIAL_8250_EXTENDED=y +CONFIG_SERIAL_8250_MANY_PORTS=y +CONFIG_SERIAL_8250_SHARE_IRQ=y +CONFIG_SERIAL_8250_DETECT_IRQ=y +CONFIG_SERIAL_8250_RSA=y + +# +# Non-8250 serial port support +# +CONFIG_SERIAL_CORE=y +CONFIG_SERIAL_CORE_CONSOLE=y +CONFIG_UNIX98_PTYS=y +# CONFIG_LEGACY_PTYS is not set +# CONFIG_IPMI_HANDLER is not set +CONFIG_HW_RANDOM=y +# CONFIG_NVRAM is not set +# CONFIG_R3964 is not set +# CONFIG_RAW_DRIVER is not set +# CONFIG_TCG_TPM is not set +CONFIG_I2C=y +CONFIG_I2C_BOARDINFO=y +CONFIG_I2C_CHARDEV=y +CONFIG_I2C_HELPER_AUTO=y + +# +# I2C Hardware Bus support +# + +# +# I2C system bus drivers (mostly embedded / system-on-chip) +# +# CONFIG_I2C_GPIO is not set +# CONFIG_I2C_OCORES is not set +CONFIG_I2C_OMAP=y +# CONFIG_I2C_SIMTEC is not set + +# +# External I2C/SMBus adapter drivers +# +# CONFIG_I2C_PARPORT_LIGHT is not set +# CONFIG_I2C_TAOS_EVM is not set + +# +# Other I2C/SMBus bus drivers +# +# CONFIG_I2C_PCA_PLATFORM is not set +# CONFIG_I2C_STUB is not set + +# +# Miscellaneous I2C Chip support +# +# CONFIG_DS1682 is not set +# CONFIG_EEPROM_AT24 is not set +# CONFIG_EEPROM_LEGACY is not set +# CONFIG_SENSORS_PCF8574 is not set +# CONFIG_PCF8575 is not set +# CONFIG_SENSORS_PCA9539 is not set +# CONFIG_SENSORS_PCF8591 is not set +# CONFIG_ISP1301_OMAP is not set +# CONFIG_TPS65010 is not set +# CONFIG_SENSORS_MAX6875 is not set +# CONFIG_SENSORS_TSL2550 is not set +# CONFIG_I2C_DEBUG_CORE is not set +# CONFIG_I2C_DEBUG_ALGO is not set +# CONFIG_I2C_DEBUG_BUS is not set +# CONFIG_I2C_DEBUG_CHIP is not set +CONFIG_SPI=y +# CONFIG_SPI_DEBUG is not set +CONFIG_SPI_MASTER=y + +# +# SPI Master Controller Drivers +# +# CONFIG_SPI_BITBANG is not set +CONFIG_SPI_OMAP24XX=y + +# +# SPI Protocol Masters +# +# CONFIG_EEPROM_AT25 is not set +# CONFIG_SPI_SPIDEV is not set +# CONFIG_SPI_TLE62X0 is not set +CONFIG_ARCH_REQUIRE_GPIOLIB=y +CONFIG_GPIOLIB=y +# CONFIG_DEBUG_GPIO is not set +# CONFIG_GPIO_SYSFS is not set + +# +# I2C GPIO expanders: +# +# CONFIG_GPIO_MAX732X is not set +# CONFIG_GPIO_PCA953X is not set +# CONFIG_GPIO_PCF857X is not set + +# +# PCI GPIO expanders: +# + +# +# SPI GPIO expanders: +# +# CONFIG_GPIO_MAX7301 is not set +# CONFIG_GPIO_MCP23S08 is not set +CONFIG_W1=y + +# +# 1-wire Bus Masters +# +# CONFIG_W1_MASTER_DS2482 is not set +# CONFIG_W1_MASTER_DS1WM is not set +# CONFIG_W1_MASTER_GPIO is not set + +# +# 1-wire Slaves +# +# CONFIG_W1_SLAVE_THERM is not set +# CONFIG_W1_SLAVE_SMEM is not set +# CONFIG_W1_SLAVE_DS2433 is not set +# CONFIG_W1_SLAVE_DS2760 is not set +CONFIG_POWER_SUPPLY=y +# CONFIG_POWER_SUPPLY_DEBUG is not set +# CONFIG_PDA_POWER is not set +# CONFIG_BATTERY_DS2760 is not set +# CONFIG_HWMON is not set +CONFIG_WATCHDOG=y +CONFIG_WATCHDOG_NOWAYOUT=y + +# +# Watchdog Device Drivers +# +# CONFIG_SOFT_WATCHDOG is not set + +# +# Sonics Silicon Backplane +# +CONFIG_SSB_POSSIBLE=y +# CONFIG_SSB is not set + +# +# Multifunction device drivers +# +# CONFIG_MFD_CORE is not set +# CONFIG_MFD_SM501 is not set +# CONFIG_HTC_EGPIO is not set +# CONFIG_HTC_PASIC3 is not set +# CONFIG_MFD_TMIO is not set +# CONFIG_MFD_T7L66XB is not set +# CONFIG_MFD_TC6387XB is not set +# CONFIG_MFD_TC6393XB is not set + +# +# Multimedia devices +# + +# +# Multimedia core support +# +# CONFIG_VIDEO_DEV is not set +# CONFIG_VIDEO_MEDIA is not set + +# +# Multimedia drivers +# +CONFIG_DAB=y + +# +# Graphics support +# +# CONFIG_VGASTATE is not set +CONFIG_VIDEO_OUTPUT_CONTROL=m +# CONFIG_FB is not set +# CONFIG_BACKLIGHT_LCD_SUPPORT is not set + +# +# Display device support +# +# CONFIG_DISPLAY_SUPPORT is not set + +# +# Console display driver support +# +# CONFIG_VGA_CONSOLE is not set +CONFIG_DUMMY_CONSOLE=y +CONFIG_SOUND=y +CONFIG_SND=y +# CONFIG_SND_SEQUENCER is not set +# CONFIG_SND_MIXER_OSS is not set +# CONFIG_SND_PCM_OSS is not set +# CONFIG_SND_DYNAMIC_MINORS is not set +CONFIG_SND_SUPPORT_OLD_API=y +CONFIG_SND_VERBOSE_PROCFS=y +# CONFIG_SND_VERBOSE_PRINTK is not set +# CONFIG_SND_DEBUG is not set +CONFIG_SND_DRIVERS=y +# CONFIG_SND_DUMMY is not set +# CONFIG_SND_MTPAV is not set +# CONFIG_SND_SERIAL_U16550 is not set +# CONFIG_SND_MPU401 is not set +CONFIG_SND_ARM=y +CONFIG_SND_SPI=y +# CONFIG_SND_SOC is not set +# CONFIG_SOUND_PRIME is not set +CONFIG_HID_SUPPORT=y +CONFIG_HID=y +# CONFIG_HID_DEBUG is not set +# CONFIG_HIDRAW is not set +# CONFIG_USB_SUPPORT is not set +CONFIG_MMC=y +# CONFIG_MMC_DEBUG is not set +# CONFIG_MMC_UNSAFE_RESUME is not set + +# +# MMC/SD Card Drivers +# +CONFIG_MMC_BLOCK=y +CONFIG_MMC_BLOCK_BOUNCE=y +# CONFIG_SDIO_UART is not set +# CONFIG_MMC_TEST is not set + +# +# MMC/SD Host Controller Drivers +# +# CONFIG_MMC_SDHCI is not set +# CONFIG_MMC_OMAP is not set +# CONFIG_MMC_SPI is not set +# CONFIG_NEW_LEDS is not set +CONFIG_RTC_LIB=y +CONFIG_RTC_CLASS=y +CONFIG_RTC_HCTOSYS=y +CONFIG_RTC_HCTOSYS_DEVICE="rtc0" +# CONFIG_RTC_DEBUG is not set + +# +# RTC interfaces +# +CONFIG_RTC_INTF_SYSFS=y +CONFIG_RTC_INTF_PROC=y +CONFIG_RTC_INTF_DEV=y +# CONFIG_RTC_INTF_DEV_UIE_EMUL is not set +# CONFIG_RTC_DRV_TEST is not set + +# +# I2C RTC drivers +# +# CONFIG_RTC_DRV_DS1307 is not set +# CONFIG_RTC_DRV_DS1374 is not set +# CONFIG_RTC_DRV_DS1672 is not set +# CONFIG_RTC_DRV_MAX6900 is not set +# CONFIG_RTC_DRV_RS5C372 is not set +# CONFIG_RTC_DRV_ISL1208 is not set +# CONFIG_RTC_DRV_X1205 is not set +# CONFIG_RTC_DRV_PCF8563 is not set +# CONFIG_RTC_DRV_PCF8583 is not set +# CONFIG_RTC_DRV_M41T80 is not set +# CONFIG_RTC_DRV_S35390A is not set +# CONFIG_RTC_DRV_FM3130 is not set + +# +# SPI RTC drivers +# +# CONFIG_RTC_DRV_M41T94 is not set +# CONFIG_RTC_DRV_DS1305 is not set +# CONFIG_RTC_DRV_MAX6902 is not set +# CONFIG_RTC_DRV_R9701 is not set +# CONFIG_RTC_DRV_RS5C348 is not set + +# +# Platform RTC drivers +# +# CONFIG_RTC_DRV_CMOS is not set +# CONFIG_RTC_DRV_DS1511 is not set +# CONFIG_RTC_DRV_DS1553 is not set +# CONFIG_RTC_DRV_DS1742 is not set +# CONFIG_RTC_DRV_STK17TA8 is not set +# CONFIG_RTC_DRV_M48T86 is not set +# CONFIG_RTC_DRV_M48T59 is not set +# CONFIG_RTC_DRV_V3020 is not set + +# +# on-CPU RTC drivers +# +# CONFIG_DMADEVICES is not set + +# +# Voltage and Current regulators +# +# CONFIG_REGULATOR is not set +# CONFIG_REGULATOR_FIXED_VOLTAGE is not set +# CONFIG_REGULATOR_VIRTUAL_CONSUMER is not set +# CONFIG_REGULATOR_BQ24022 is not set +# CONFIG_UIO is not set + +# +# File systems +# +CONFIG_EXT2_FS=y +# CONFIG_EXT2_FS_XATTR is not set +# CONFIG_EXT2_FS_XIP is not set +CONFIG_EXT3_FS=y +# CONFIG_EXT3_FS_XATTR is not set +# CONFIG_EXT4DEV_FS is not set +CONFIG_JBD=y +# CONFIG_REISERFS_FS is not set +# CONFIG_JFS_FS is not set +# CONFIG_FS_POSIX_ACL is not set +# CONFIG_XFS_FS is not set +CONFIG_DNOTIFY=y +CONFIG_INOTIFY=y +CONFIG_INOTIFY_USER=y +CONFIG_QUOTA=y +CONFIG_PRINT_QUOTA_WARNING=y +# CONFIG_QFMT_V1 is not set +CONFIG_QFMT_V2=y +CONFIG_QUOTACTL=y +# CONFIG_AUTOFS_FS is not set +# CONFIG_AUTOFS4_FS is not set +# CONFIG_FUSE_FS is not set + +# +# CD-ROM/DVD Filesystems +# +# CONFIG_ISO9660_FS is not set +# CONFIG_UDF_FS is not set + +# +# DOS/FAT/NT Filesystems +# +CONFIG_FAT_FS=y +CONFIG_MSDOS_FS=y +CONFIG_VFAT_FS=y +CONFIG_FAT_DEFAULT_CODEPAGE=437 +CONFIG_FAT_DEFAULT_IOCHARSET="iso8859-1" +# CONFIG_NTFS_FS is not set + +# +# Pseudo filesystems +# +CONFIG_PROC_FS=y +CONFIG_PROC_SYSCTL=y +CONFIG_SYSFS=y +CONFIG_TMPFS=y +# CONFIG_TMPFS_POSIX_ACL is not set +# CONFIG_HUGETLB_PAGE is not set +# CONFIG_CONFIGFS_FS is not set + +# +# Miscellaneous filesystems +# +# CONFIG_ADFS_FS is not set +# CONFIG_AFFS_FS is not set +# CONFIG_HFS_FS is not set +# CONFIG_HFSPLUS_FS is not set +# CONFIG_BEFS_FS is not set +# CONFIG_BFS_FS is not set +# CONFIG_EFS_FS is not set +# CONFIG_CRAMFS is not set +# CONFIG_VXFS_FS is not set +# CONFIG_MINIX_FS is not set +# CONFIG_OMFS_FS is not set +# CONFIG_HPFS_FS is not set +# CONFIG_QNX4FS_FS is not set +# CONFIG_ROMFS_FS is not set +# CONFIG_SYSV_FS is not set +# CONFIG_UFS_FS is not set +CONFIG_NETWORK_FILESYSTEMS=y +CONFIG_NFS_FS=y +CONFIG_NFS_V3=y +CONFIG_NFS_V3_ACL=y +CONFIG_NFS_V4=y +CONFIG_ROOT_NFS=y +# CONFIG_NFSD is not set +CONFIG_LOCKD=y +CONFIG_LOCKD_V4=y +CONFIG_NFS_ACL_SUPPORT=y +CONFIG_NFS_COMMON=y +CONFIG_SUNRPC=y +CONFIG_SUNRPC_GSS=y +# CONFIG_SUNRPC_REGISTER_V4 is not set +CONFIG_RPCSEC_GSS_KRB5=y +# CONFIG_RPCSEC_GSS_SPKM3 is not set +# CONFIG_SMB_FS is not set +# CONFIG_CIFS is not set +# CONFIG_NCP_FS is not set +# CONFIG_CODA_FS is not set +# CONFIG_AFS_FS is not set + +# +# Partition Types +# +CONFIG_PARTITION_ADVANCED=y +# CONFIG_ACORN_PARTITION is not set +# CONFIG_OSF_PARTITION is not set +# CONFIG_AMIGA_PARTITION is not set +# CONFIG_ATARI_PARTITION is not set +# CONFIG_MAC_PARTITION is not set +CONFIG_MSDOS_PARTITION=y +# CONFIG_BSD_DISKLABEL is not set +# CONFIG_MINIX_SUBPARTITION is not set +# CONFIG_SOLARIS_X86_PARTITION is not set +# CONFIG_UNIXWARE_DISKLABEL is not set +# CONFIG_LDM_PARTITION is not set +# CONFIG_SGI_PARTITION is not set +# CONFIG_ULTRIX_PARTITION is not set +# CONFIG_SUN_PARTITION is not set +# CONFIG_KARMA_PARTITION is not set +# CONFIG_EFI_PARTITION is not set +# CONFIG_SYSV68_PARTITION is not set +CONFIG_NLS=y +CONFIG_NLS_DEFAULT="iso8859-1" +CONFIG_NLS_CODEPAGE_437=y +# CONFIG_NLS_CODEPAGE_737 is not set +# CONFIG_NLS_CODEPAGE_775 is not set +# CONFIG_NLS_CODEPAGE_850 is not set +# CONFIG_NLS_CODEPAGE_852 is not set +# CONFIG_NLS_CODEPAGE_855 is not set +# CONFIG_NLS_CODEPAGE_857 is not set +# CONFIG_NLS_CODEPAGE_860 is not set +# CONFIG_NLS_CODEPAGE_861 is not set +# CONFIG_NLS_CODEPAGE_862 is not set +# CONFIG_NLS_CODEPAGE_863 is not set +# CONFIG_NLS_CODEPAGE_864 is not set +# CONFIG_NLS_CODEPAGE_865 is not set +# CONFIG_NLS_CODEPAGE_866 is not set +# CONFIG_NLS_CODEPAGE_869 is not set +# CONFIG_NLS_CODEPAGE_936 is not set +# CONFIG_NLS_CODEPAGE_950 is not set +# CONFIG_NLS_CODEPAGE_932 is not set +# CONFIG_NLS_CODEPAGE_949 is not set +# CONFIG_NLS_CODEPAGE_874 is not set +# CONFIG_NLS_ISO8859_8 is not set +# CONFIG_NLS_CODEPAGE_1250 is not set +# CONFIG_NLS_CODEPAGE_1251 is not set +# CONFIG_NLS_ASCII is not set +CONFIG_NLS_ISO8859_1=y +# CONFIG_NLS_ISO8859_2 is not set +# CONFIG_NLS_ISO8859_3 is not set +# CONFIG_NLS_ISO8859_4 is not set +# CONFIG_NLS_ISO8859_5 is not set +# CONFIG_NLS_ISO8859_6 is not set +# CONFIG_NLS_ISO8859_7 is not set +# CONFIG_NLS_ISO8859_9 is not set +# CONFIG_NLS_ISO8859_13 is not set +# CONFIG_NLS_ISO8859_14 is not set +# CONFIG_NLS_ISO8859_15 is not set +# CONFIG_NLS_KOI8_R is not set +# CONFIG_NLS_KOI8_U is not set +# CONFIG_NLS_UTF8 is not set + +# +# Kernel hacking +# +# CONFIG_PRINTK_TIME is not set +CONFIG_ENABLE_WARN_DEPRECATED=y +CONFIG_ENABLE_MUST_CHECK=y +CONFIG_FRAME_WARN=1024 +CONFIG_MAGIC_SYSRQ=y +# CONFIG_UNUSED_SYMBOLS is not set +# CONFIG_DEBUG_FS is not set +# CONFIG_HEADERS_CHECK is not set +CONFIG_DEBUG_KERNEL=y +# CONFIG_DEBUG_SHIRQ is not set +CONFIG_DETECT_SOFTLOCKUP=y +# CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC is not set +CONFIG_BOOTPARAM_SOFTLOCKUP_PANIC_VALUE=0 +CONFIG_SCHED_DEBUG=y +# CONFIG_SCHEDSTATS is not set +# CONFIG_TIMER_STATS is not set +# CONFIG_DEBUG_OBJECTS is not set +# CONFIG_DEBUG_SLAB is not set +# CONFIG_DEBUG_RT_MUTEXES is not set +# CONFIG_RT_MUTEX_TESTER is not set +# CONFIG_DEBUG_SPINLOCK is not set +CONFIG_DEBUG_MUTEXES=y +# CONFIG_DEBUG_LOCK_ALLOC is not set +# CONFIG_PROVE_LOCKING is not set +# CONFIG_LOCK_STAT is not set +# CONFIG_DEBUG_SPINLOCK_SLEEP is not set +# CONFIG_DEBUG_LOCKING_API_SELFTESTS is not set +# CONFIG_DEBUG_KOBJECT is not set +# CONFIG_DEBUG_BUGVERBOSE is not set +CONFIG_DEBUG_INFO=y +# CONFIG_DEBUG_VM is not set +# CONFIG_DEBUG_WRITECOUNT is not set +# CONFIG_DEBUG_MEMORY_INIT is not set +# CONFIG_DEBUG_LIST is not set +# CONFIG_DEBUG_SG is not set +CONFIG_FRAME_POINTER=y +# CONFIG_BOOT_PRINTK_DELAY is not set +# CONFIG_RCU_TORTURE_TEST is not set +# CONFIG_BACKTRACE_SELF_TEST is not set +# CONFIG_FAULT_INJECTION is not set +# CONFIG_LATENCYTOP is not set +CONFIG_HAVE_FTRACE=y +CONFIG_HAVE_DYNAMIC_FTRACE=y +# CONFIG_FTRACE is not set +# CONFIG_IRQSOFF_TRACER is not set +# CONFIG_SCHED_TRACER is not set +# CONFIG_CONTEXT_SWITCH_TRACER is not set +# CONFIG_SAMPLES is not set +CONFIG_HAVE_ARCH_KGDB=y +# CONFIG_KGDB is not set +# CONFIG_DEBUG_USER is not set +# CONFIG_DEBUG_ERRORS is not set +# CONFIG_DEBUG_STACK_USAGE is not set +CONFIG_DEBUG_LL=y +# CONFIG_DEBUG_ICEDCC is not set + +# +# Security options +# +# CONFIG_KEYS is not set +# CONFIG_SECURITY is not set +# CONFIG_SECURITY_FILE_CAPABILITIES is not set +CONFIG_CRYPTO=y + +# +# Crypto core or helper +# +CONFIG_CRYPTO_ALGAPI=y +CONFIG_CRYPTO_BLKCIPHER=y +CONFIG_CRYPTO_MANAGER=y +# CONFIG_CRYPTO_GF128MUL is not set +# CONFIG_CRYPTO_NULL is not set +# CONFIG_CRYPTO_CRYPTD is not set +# CONFIG_CRYPTO_AUTHENC is not set +# CONFIG_CRYPTO_TEST is not set + +# +# Authenticated Encryption with Associated Data +# +# CONFIG_CRYPTO_CCM is not set +# CONFIG_CRYPTO_GCM is not set +# CONFIG_CRYPTO_SEQIV is not set + +# +# Block modes +# +CONFIG_CRYPTO_CBC=y +# CONFIG_CRYPTO_CTR is not set +# CONFIG_CRYPTO_CTS is not set +CONFIG_CRYPTO_ECB=m +# CONFIG_CRYPTO_LRW is not set +CONFIG_CRYPTO_PCBC=m +# CONFIG_CRYPTO_XTS is not set + +# +# Hash modes +# +# CONFIG_CRYPTO_HMAC is not set +# CONFIG_CRYPTO_XCBC is not set + +# +# Digest +# +# CONFIG_CRYPTO_CRC32C is not set +# CONFIG_CRYPTO_MD4 is not set +CONFIG_CRYPTO_MD5=y +# CONFIG_CRYPTO_MICHAEL_MIC is not set +# CONFIG_CRYPTO_RMD128 is not set +# CONFIG_CRYPTO_RMD160 is not set +# CONFIG_CRYPTO_RMD256 is not set +# CONFIG_CRYPTO_RMD320 is not set +# CONFIG_CRYPTO_SHA1 is not set +# CONFIG_CRYPTO_SHA256 is not set +# CONFIG_CRYPTO_SHA512 is not set +# CONFIG_CRYPTO_TGR192 is not set +# CONFIG_CRYPTO_WP512 is not set + +# +# Ciphers +# +# CONFIG_CRYPTO_AES is not set +# CONFIG_CRYPTO_ANUBIS is not set +# CONFIG_CRYPTO_ARC4 is not set +# CONFIG_CRYPTO_BLOWFISH is not set +# CONFIG_CRYPTO_CAMELLIA is not set +# CONFIG_CRYPTO_CAST5 is not set +# CONFIG_CRYPTO_CAST6 is not set +CONFIG_CRYPTO_DES=y +# CONFIG_CRYPTO_FCRYPT is not set +# CONFIG_CRYPTO_KHAZAD is not set +# CONFIG_CRYPTO_SALSA20 is not set +# CONFIG_CRYPTO_SEED is not set +# CONFIG_CRYPTO_SERPENT is not set +# CONFIG_CRYPTO_TEA is not set +# CONFIG_CRYPTO_TWOFISH is not set + +# +# Compression +# +# CONFIG_CRYPTO_DEFLATE is not set +# CONFIG_CRYPTO_LZO is not set +CONFIG_CRYPTO_HW=y + +# +# Library routines +# +CONFIG_BITREVERSE=y +# CONFIG_GENERIC_FIND_FIRST_BIT is not set +# CONFIG_GENERIC_FIND_NEXT_BIT is not set +CONFIG_CRC_CCITT=y +# CONFIG_CRC16 is not set +CONFIG_CRC_T10DIF=y +# CONFIG_CRC_ITU_T is not set +CONFIG_CRC32=y +# CONFIG_CRC7 is not set +CONFIG_LIBCRC32C=y +CONFIG_PLIST=y +CONFIG_HAS_IOMEM=y +CONFIG_HAS_IOPORT=y +CONFIG_HAS_DMA=y -- 1.5.4.3 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* [PATCH 3/3] OMAP3:zoom2: Makefile and Kconfig for Zoom2 board 2009-05-07 21:42 ` [PATCH 2/3] OMAP3:zoom2: Defconfig for " Mikkel Christensen @ 2009-05-07 21:42 ` Mikkel Christensen 0 siblings, 0 replies; 6+ messages in thread From: Mikkel Christensen @ 2009-05-07 21:42 UTC (permalink / raw) To: linux-omap; +Cc: Mikkel Christensen, Vikram Pandita This patch adds OMAP3 Zoom2 board to the Makefile and Kconfig. Signed-off-by: Mikkel Christensen <mlc@ti.com> Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> --- arch/arm/mach-omap2/Kconfig | 4 ++++ arch/arm/mach-omap2/Makefile | 4 +++- 2 files changed, 7 insertions(+), 1 deletions(-) diff --git a/arch/arm/mach-omap2/Kconfig b/arch/arm/mach-omap2/Kconfig index 64ab386..0b16255 100644 --- a/arch/arm/mach-omap2/Kconfig +++ b/arch/arm/mach-omap2/Kconfig @@ -67,3 +67,7 @@ config MACH_OMAP_3430SDP config MACH_NOKIA_RX51 bool "Nokia RX-51 board" depends on ARCH_OMAP3 && ARCH_OMAP34XX + +config MACH_OMAP_ZOOM2 + bool "OMAP3 Zoom2 board" + depends on ARCH_OMAP3 && ARCH_OMAP34XX \ No newline at end of file diff --git a/arch/arm/mach-omap2/Makefile b/arch/arm/mach-omap2/Makefile index c49d9bf..fe4485f 100644 --- a/arch/arm/mach-omap2/Makefile +++ b/arch/arm/mach-omap2/Makefile @@ -48,7 +48,9 @@ obj-$(CONFIG_MACH_OMAP_3430SDP) += board-3430sdp.o \ obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o \ board-rx51-peripherals.o \ mmc-twl4030.o - +obj-$(CONFIG_MACH_OMAP_ZOOM2) += board-zoom2.o \ + mmc-twl4030.o \ + board-zoom2-debugboard.o # Platform specific device init code ifeq ($(CONFIG_USB_MUSB_SOC),y) obj-y += usb-musb.o -- 1.5.4.3 ^ permalink raw reply related [flat|nested] 6+ messages in thread
* Re: [PATCH 1/3] OMAP3:zoom2: Add support for OMAP3 Zoom2 board 2009-05-07 21:42 ` [PATCH 1/3] OMAP3:zoom2: Add support " Mikkel Christensen 2009-05-07 21:42 ` [PATCH 2/3] OMAP3:zoom2: Defconfig for " Mikkel Christensen @ 2009-05-13 18:44 ` Kevin Hilman 1 sibling, 0 replies; 6+ messages in thread From: Kevin Hilman @ 2009-05-13 18:44 UTC (permalink / raw) To: Mikkel Christensen; +Cc: linux-omap, Vikram Pandita Mikkel Christensen <mlc@ti.com> writes: > This patch creates the minimal OMAP3 Zoom2 board support. > > Signed-off-by: Mikkel Christensen <mlc@ti.com> > Signed-off-by: Vikram Pandita <vikram.pandita@ti.com> > --- > arch/arm/mach-omap2/board-zoom2-debugboard.c | 150 ++++++++++++++++++++++++++ > arch/arm/mach-omap2/board-zoom2.c | 126 +++++++++++++++++++++ > 2 files changed, 276 insertions(+), 0 deletions(-) > create mode 100644 arch/arm/mach-omap2/board-zoom2-debugboard.c > create mode 100644 arch/arm/mach-omap2/board-zoom2.c Any reason you decided on a separate board file for the debug board? While not a big deal, this not a separate board and is an extention of the zoom2. I would rather see everything in board-zoom2.c along with a separate init and platform_device setup/register for the debug board IFF it is present. I understand that u-boot has a way of detecting if the debug board is present. The board init code should also detect if the board is present and init/regsiter devices present only if present. > diff --git a/arch/arm/mach-omap2/board-zoom2-debugboard.c b/arch/arm/mach-omap2/board-zoom2-debugboard.c > new file mode 100644 > index 0000000..ae90f2b > --- /dev/null > +++ b/arch/arm/mach-omap2/board-zoom2-debugboard.c > @@ -0,0 +1,150 @@ > +/* > + * arch/arm/mach-omap2/board-zoom2-debugboard.c > + * > + * OMAP3 Zoom2 debug board support. > + * > + * Copyright (C) 2009 Texas Instruments Inc. > + * Mikkel Christensen <mlc@ti.com> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > +#include <linux/kernel.h> > +#include <linux/init.h> > +#include <linux/delay.h> > +#include <linux/serial_8250.h> > +#include <linux/serial_reg.h> > +#include <linux/smsc911x.h> > +#include <linux/io.h> > + > +#include <mach/common.h> > +#include <mach/board.h> > +#include <mach/gpio.h> > +#include <mach/gpmc.h> > + > +#define ZOOM2_SMSC911X_CS 7 > +#define ZOOM2_SMSC911X_GPIO 158 > +#define ZOOM2_QUADUART_CS 3 > +#define ZOOM2_QUADUART_GPIO 102 > +#define QUART_CLK 1843200 > +#define DEBUG_BASE 0x08000000 > +#define ZOOM2_ETHR_START DEBUG_BASE > + > +static struct resource zoom2_smsc911x_resources[] = { > + [0] = { > + .start = ZOOM2_ETHR_START, > + .end = ZOOM2_ETHR_START + SZ_4K, > + .flags = IORESOURCE_MEM, > + }, > + [1] = { > + .start = 0, > + .end = 0, Just leave these out, you init the IRQ later at runtime. And FYI, you don't need 'end' for an IRQ. > + .flags = IORESOURCE_IRQ | IORESOURCE_IRQ_LOWLEVEL, > + }, > +}; > + > +static struct smsc911x_platform_config zoom2_smsc911x_config = { > + .irq_polarity = SMSC911X_IRQ_POLARITY_ACTIVE_LOW, > + .irq_type = SMSC911X_IRQ_TYPE_OPEN_DRAIN, > + .flags = SMSC911X_USE_32BIT, > + .phy_interface = PHY_INTERFACE_MODE_MII, > +}; > + > +static struct platform_device zoom2_smsc911x_device = { > + .name = "smsc911x", > + .id = -1, > + .num_resources = ARRAY_SIZE(zoom2_smsc911x_resources), > + .resource = zoom2_smsc911x_resources, > + .dev = { > + .platform_data = &zoom2_smsc911x_config, > + }, > +}; > + > +static inline void __init zoom2_init_smsc911x(void) > +{ > + int eth_cs; > + unsigned long cs_mem_base; > + int eth_gpio = 0; > + > + eth_cs = ZOOM2_SMSC911X_CS; > + > + if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) { > + printk(KERN_ERR "Failed to request GPMC mem for smsc911x\n"); > + return; > + } > + > + zoom2_smsc911x_resources[0].start = cs_mem_base + 0x0; > + zoom2_smsc911x_resources[0].end = cs_mem_base + 0xff; > + udelay(100); What's this delay for? I think it should be dropped. > + eth_gpio = ZOOM2_SMSC911X_GPIO; > + > + zoom2_smsc911x_resources[1].start = OMAP_GPIO_IRQ(eth_gpio); > + > + if (gpio_request(eth_gpio, "smsc911x irq") < 0) { > + printk(KERN_ERR "Failed to request GPIO%d for smsc911x IRQ\n", > + eth_gpio); > + return; > + } > + gpio_direction_input(eth_gpio); > +} > + > +static struct plat_serial8250_port serial_platform_data[] = { > + { > + .membase = 0, You don't need to set fields to zero. They will init to zero. > + .mapbase = 0x10000000, > + .irq = OMAP_GPIO_IRQ(102), > + .flags = UPF_BOOT_AUTOCONF|UPF_IOREMAP|UPF_SHARE_IRQ, > + .iotype = UPIO_MEM, > + .regshift = 1, > + .uartclk = QUART_CLK, > + }, { > + .flags = 0 > + } > +}; > + > +static struct platform_device zoom2_debugboard_serial_device = { > + .name = "serial8250", > + .id = PLAT8250_DEV_PLATFORM1, > + .dev = { > + .platform_data = serial_platform_data, > + }, > +}; > + > +static inline void __init zoom2_init_quaduart(void) > +{ > + int quart_cs; > + unsigned long cs_mem_base; > + int quart_gpio = 0; > + > + quart_cs = ZOOM2_QUADUART_CS; > + > + if (gpmc_cs_request(quart_cs, SZ_1M, &cs_mem_base) < 0) { > + printk(KERN_ERR "Failed to request GPMC mem" > + "for Quad UART(TL16CP754C)\n"); > + return; > + } > + > + quart_gpio = ZOOM2_QUADUART_GPIO; > + > + if (gpio_request(quart_gpio, "TL16CP754C GPIO") < 0) { > + printk(KERN_ERR "Failed to request GPIO%d for TL16CP754C\n", > + quart_gpio); > + return; > + } > + gpio_direction_input(quart_gpio); > +} > + > +static struct platform_device *zoom2_devices[] __initdata = { > + &zoom2_smsc911x_device, > + &zoom2_debugboard_serial_device, > +}; > + > +static int __init omap_zoom2_debugboard_init(void) > +{ This debug board init should include some form of probing for the debug board, and only continue if it is present. > + zoom2_init_smsc911x(); > + zoom2_init_quaduart(); > + return platform_add_devices(zoom2_devices, ARRAY_SIZE(zoom2_devices)); > +} > +arch_initcall(omap_zoom2_debugboard_init); > diff --git a/arch/arm/mach-omap2/board-zoom2.c b/arch/arm/mach-omap2/board-zoom2.c > new file mode 100644 > index 0000000..f43809a > --- /dev/null > +++ b/arch/arm/mach-omap2/board-zoom2.c > @@ -0,0 +1,126 @@ > +/* > + * linux/arch/arm/mach-omap2/board-zoom2.c > + * > + * Copyright (C) 2009 Texas Instruments Inc. > + * Mikkel Christensen <mlc@ti.com> > + * > + * Modified from mach-omap2/board-ldp.c > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/kernel.h> > +#include <linux/init.h> > +#include <linux/platform_device.h> > +#include <linux/delay.h> > +#include <linux/input.h> > +#include <linux/workqueue.h> > +#include <linux/err.h> > +#include <linux/clk.h> > +#include <linux/spi/spi.h> > +#include <linux/spi/ads7846.h> > +#include <linux/i2c/twl4030.h> > +#include <linux/serial_8250.h> > +#include <linux/io.h> > > +#include <mach/hardware.h> > +#include <asm/mach-types.h> > +#include <asm/mach/arch.h> > +#include <asm/mach/map.h> > + > +#include <mach/mcspi.h> > +#include <mach/gpio.h> > +#include <mach/board.h> > +#include <mach/common.h> > +#include <mach/gpmc.h> > + > +#include <asm/delay.h> > +#include <mach/control.h> > +#include <mach/usb.h> > + > +#include "mmc-twl4030.h" I think there are many headers above that are not needed. Please keep only ones that are used. > + > +static void __init omap_zoom2_init_irq(void) > +{ > + omap2_init_common_hw(NULL); > + omap_init_irq(); > + omap_gpio_init(); > +} > + > +static struct omap_uart_config zoom2_uart_config __initdata = { > + .enabled_uarts = ((1 << 0) | (1 << 1) | (1 << 2)), > +}; > + > +static struct omap_board_config_kernel zoom2_config[] __initdata = { > + { OMAP_TAG_UART, &zoom2_uart_config }, > +}; > + > +static struct twl4030_gpio_platform_data zoom2_gpio_data = { > + .gpio_base = OMAP_MAX_GPIO_LINES, > + .irq_base = TWL4030_GPIO_IRQ_BASE, > + .irq_end = TWL4030_GPIO_IRQ_END, > +}; > + > +static struct twl4030_platform_data zoom2_twldata = { > + .irq_base = TWL4030_IRQ_BASE, > + .irq_end = TWL4030_IRQ_END, > + > + /* platform_data for children goes here */ > + .gpio = &zoom2_gpio_data, > +}; > + > +static struct i2c_board_info __initdata zoom2_i2c_boardinfo[] = { > + { > + I2C_BOARD_INFO("twl4030", 0x48), > + .flags = I2C_CLIENT_WAKE, > + .irq = INT_34XX_SYS_NIRQ, > + .platform_data = &zoom2_twldata, > + }, > +}; > + > +static int __init omap_i2c_init(void) > +{ > + omap_register_i2c_bus(1, 2600, zoom2_i2c_boardinfo, > + ARRAY_SIZE(zoom2_i2c_boardinfo)); > + omap_register_i2c_bus(2, 400, NULL, 0); > + omap_register_i2c_bus(3, 400, NULL, 0); > + return 0; > +} > + > +static struct twl4030_hsmmc_info mmc[] __initdata = { > + { > + .mmc = 1, > + .wires = 4, > + .gpio_cd = -EINVAL, > + .gpio_wp = -EINVAL, > + }, > + {} /* Terminator */ > +}; > + > +static void __init omap_zoom2_init(void) > +{ > + omap_i2c_init(); > + omap_board_config = zoom2_config; > + omap_board_config_size = ARRAY_SIZE(zoom2_config); > + omap_serial_init(); > + twl4030_mmc_init(mmc); > + usb_musb_init(); > +} > + > +static void __init omap_zoom2_map_io(void) > +{ > + omap2_set_globals_343x(); > + omap2_map_common_io(); > +} > + > +MACHINE_START(OMAP_ZOOM2, "OMAP Zoom2 board") > + .phys_io = 0x48000000, > + .io_pg_offst = ((0xd8000000) >> 18) & 0xfffc, > + .boot_params = 0x80000100, > + .map_io = omap_zoom2_map_io, > + .init_irq = omap_zoom2_init_irq, > + .init_machine = omap_zoom2_init, > + .timer = &omap_timer, > +MACHINE_END > -- > 1.5.4.3 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-omap" in > the body of a message to majordomo@vger.kernel.org > More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: [PATCH 0/3] Support for OMAP3 Zoom2 board 2009-05-07 21:42 [PATCH 0/3] Support for OMAP3 Zoom2 board Mikkel Christensen 2009-05-07 21:42 ` [PATCH 1/3] OMAP3:zoom2: Add support " Mikkel Christensen @ 2009-05-13 17:53 ` Pandita, Vikram 1 sibling, 0 replies; 6+ messages in thread From: Pandita, Vikram @ 2009-05-13 17:53 UTC (permalink / raw) To: linux-omap@vger.kernel.org; +Cc: Christensen, Mikkel Tony/All Any comments on Zoom2 support patches? >-----Original Message----- >From: linux-omap-owner@vger.kernel.org [mailto:linux-omap-owner@vger.kernel.org] On Behalf Of >Christensen, Mikkel >Sent: Thursday, May 07, 2009 4:42 PM >To: linux-omap@vger.kernel.org >Cc: Christensen, Mikkel >Subject: [PATCH 0/3] Support for OMAP3 Zoom2 board > >The following patch series adds support for Zoom2 board. > >The board has: > - Modem attached to UART1 > - WLAN attached to UART2 > - GPS attached to UART3 > >An external debug board is included for console and LAN. > >For details refer to this site: >http://www.logicpd.com/products/development-kits/texas-instruments-zoom%E2%84%A2-omap34x-ii-mdp > >Future work: > - SMSC911x NFS mount problem > - Low level debug uart need to use debug board > - Dynamic detection of debug board presence > >TI wiki with FAQs on getting this board booting: >https://omapzoom.org/gf/project/omapzoom/wiki/?pagename=GettingStartedWithZoomII_AKA_OMAP34XII_MDP >-- >To unsubscribe from this list: send the line "unsubscribe linux-omap" in >the body of a message to majordomo@vger.kernel.org >More majordomo info at http://vger.kernel.org/majordomo-info.html ^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2009-05-13 18:44 UTC | newest] Thread overview: 6+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2009-05-07 21:42 [PATCH 0/3] Support for OMAP3 Zoom2 board Mikkel Christensen 2009-05-07 21:42 ` [PATCH 1/3] OMAP3:zoom2: Add support " Mikkel Christensen 2009-05-07 21:42 ` [PATCH 2/3] OMAP3:zoom2: Defconfig for " Mikkel Christensen 2009-05-07 21:42 ` [PATCH 3/3] OMAP3:zoom2: Makefile and Kconfig " Mikkel Christensen 2009-05-13 18:44 ` [PATCH 1/3] OMAP3:zoom2: Add support for OMAP3 " Kevin Hilman 2009-05-13 17:53 ` [PATCH 0/3] Support " Pandita, Vikram
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox