From: Kevin Hilman <khilman@deeprootsystems.com>
To: Thara Gopinath <thara@ti.com>
Cc: linux-omap@vger.kernel.org, paul@pwsan.com, nm@ti.com,
b-cousson@ti.com, vishwanath.bs@ti.com, sawant@ti.com
Subject: Re: [PATCH 14/16] OMAP3: PM: Implement latest h/w recommendations for SR and VP registers and SR VP enable disable sequence.
Date: Tue, 02 Mar 2010 16:54:51 -0800 [thread overview]
Message-ID: <87y6iap6lg.fsf@deeprootsystems.com> (raw)
In-Reply-To: <1267003757-22456-15-git-send-email-thara@ti.com> (Thara Gopinath's message of "Wed\, 24 Feb 2010 14\:59\:15 +0530")
Thara Gopinath <thara@ti.com> writes:
> This patch introduces OMAP3 specific values for Smartreflex and
> Voltage processor registers as per the latest TI recommendations.
> This patch also improves the smartreflex and voltage processor
> enable disable sequences as per the latest recommendations.
>
> These recommendations were first formed based on experimentations
> on Nokia Rover platform and were implemented in the Rover code
> base first by Nishanth Menon and Paul Walmsley.
I think this was pointed out by others, but Rover should be replaced
with n900.
> Signed-off-by: Thara Gopinath <thara@ti.com>
> ---
> arch/arm/mach-omap2/smartreflex.c | 65 ++++++++++++++++++++-----
> arch/arm/mach-omap2/smartreflex.h | 6 +-
> arch/arm/mach-omap2/voltage.c | 95 ++++++++++++++++++++++++++++++------
> arch/arm/mach-omap2/voltage.h | 16 ++++---
> 4 files changed, 142 insertions(+), 40 deletions(-)
>
> diff --git a/arch/arm/mach-omap2/smartreflex.c b/arch/arm/mach-omap2/smartreflex.c
> index 8a4c48b..ca2223d 100644
> --- a/arch/arm/mach-omap2/smartreflex.c
> +++ b/arch/arm/mach-omap2/smartreflex.c
> @@ -24,6 +24,7 @@
> #include <linux/io.h>
> #include <linux/list.h>
> #include <linux/debugfs.h>
> +#include <linux/delay.h>
>
> #include <plat/control.h>
> #include <plat/omap_hwmod.h>
> @@ -32,6 +33,7 @@
> #include "smartreflex.h"
>
> #define SMARTREFLEX_NAME_LEN 16
> +#define SR_DISABLE_TIMEOUT 200
>
> struct omap_sr {
> int srid;
> @@ -184,11 +186,9 @@ static void sr_set_regfields(struct omap_sr *sr)
> sr->err_maxlimit = OMAP3430_SR_ERRMAXLIMIT;
> sr->accum_data = OMAP3430_SR_ACCUMDATA;
> if (sr->srid == SR1) {
> - sr->err_minlimit = OMAP3430_SR1_ERRMINLIMIT;
> sr->senn_avgweight = OMAP3430_SR1_SENNAVGWEIGHT;
> sr->senp_avgweight = OMAP3430_SR1_SENPAVGWEIGHT;
> } else {
> - sr->err_minlimit = OMAP3430_SR2_ERRMINLIMIT;
> sr->senn_avgweight = OMAP3430_SR2_SENNAVGWEIGHT;
> sr->senp_avgweight = OMAP3430_SR2_SENPAVGWEIGHT;
> }
> @@ -280,11 +280,6 @@ static void sr_start_vddautocomap(int srid)
> return;
> }
>
> - if (sr->is_sr_reset == 1) {
> - sr_clk_enable(sr);
> - sr_configure(sr);
> - }
> -
> sr->is_autocomp_active = 1;
> if (!sr_class->enable(srid)) {
> sr->is_autocomp_active = 0;
> @@ -351,8 +346,20 @@ int sr_enable(int srid, u32 target_opp_no)
> return false;
> }
>
> - nvalue_reciprocal = pdata->sr_nvalue[target_opp_no - 1];
> + /*
> + * For OMAP3430 errminlimit is dependent on opp. So choose
> + * it appropriately
> + */
> + if (cpu_is_omap343x())
> + sr->err_minlimit = (target_opp_no > 2) ?
> + OMAP3430_SR_ERRMINLIMIT_HIGHOPP :
> + OMAP3430_SR_ERRMINLIMIT_LOWOPP;
> +
> + /* Enable the clocks and configure SR */
> + sr_clk_enable(sr);
> + sr_configure(sr);
>
> + nvalue_reciprocal = pdata->sr_nvalue[target_opp_no - 1];
> if (nvalue_reciprocal == 0) {
> pr_notice("OPP%d doesn't support SmartReflex\n",
> target_opp_no);
> @@ -375,10 +382,44 @@ int sr_enable(int srid, u32 target_opp_no)
> void sr_disable(int srid)
> {
> struct omap_sr *sr = _sr_lookup(srid);
> + int timeout = 0;
> +
> + /* Check if SR is already disabled. If yes do nothing */
> + if (!(sr_read_reg(sr, SRCONFIG) & SRCONFIG_SRENABLE))
> + return;
> +
> + /* Enable MCUDisableAcknowledge interrupt */
> + sr_modify_reg(sr, ERRCONFIG,
> + ERRCONFIG_MCUDISACKINTEN, ERRCONFIG_MCUDISACKINTEN);
>
> - sr->is_sr_reset = 1;
> /* SRCONFIG - disable SR */
> - sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, ~SRCONFIG_SRENABLE);
> + sr_modify_reg(sr, SRCONFIG, SRCONFIG_SRENABLE, 0x0);
> +
> + /* Disable all other SR interrupts and clear the status */
> + sr_modify_reg(sr, ERRCONFIG,
> + (ERRCONFIG_MCUACCUMINTEN | ERRCONFIG_MCUVALIDINTEN |
> + ERRCONFIG_MCUBOUNDINTEN | ERRCONFIG_VPBOUNDINTEN),
> + (ERRCONFIG_MCUACCUMINTST | ERRCONFIG_MCUVALIDINTST |
> + ERRCONFIG_MCUBOUNDINTST | ERRCONFIG_VPBOUNDINTST));
> +
> + /* Wait for SR to be disabled.
> + * wait until ERRCONFIG.MCUDISACKINTST = 1. Typical latency is 1us.
> + */
> + while ((timeout < SR_DISABLE_TIMEOUT) &&
> + (!(sr_read_reg(sr, ERRCONFIG) & ERRCONFIG_MCUDISACKINTST))) {
> +
> + udelay(1);
> + timeout++;
> + }
Please use omap_test_timeout() from <plat/common.h>
> + if (timeout == SR_DISABLE_TIMEOUT)
> + pr_warning("SR%d disable timedout\n", srid);
> +
> + /* Disable MCUDisableAcknowledge interrupt & clear pending interrupt
> + * Also enable VPBOUND interrrupt
> + */
> + sr_modify_reg(sr, ERRCONFIG, ERRCONFIG_MCUDISACKINTEN,
> + ERRCONFIG_MCUDISACKINTST);
> }
>
> /**
> @@ -407,10 +448,6 @@ void omap_smartreflex_enable(int srid)
>
> if (sr->is_autocomp_active == 1) {
> if (sr->is_sr_reset == 1) {
> - /* Enable SR clks */
> - sr_clk_enable(sr);
> - sr_configure(sr);
> -
> if (!sr_class->enable(srid))
> sr_clk_disable(sr);
> }
> diff --git a/arch/arm/mach-omap2/smartreflex.h b/arch/arm/mach-omap2/smartreflex.h
> index fbb6bf4..ae8d5db 100644
> --- a/arch/arm/mach-omap2/smartreflex.h
> +++ b/arch/arm/mach-omap2/smartreflex.h
> @@ -110,10 +110,10 @@ extern struct dentry *pm_dbg_main_dir;
> #define OMAP3430_SR2_SENPAVGWEIGHT 0x01
> #define OMAP3430_SR2_SENNAVGWEIGHT 0x01
>
> -#define OMAP3430_SR_ERRWEIGHT 0x07
> +#define OMAP3430_SR_ERRWEIGHT 0x04
> #define OMAP3430_SR_ERRMAXLIMIT 0x02
> -#define OMAP3430_SR1_ERRMINLIMIT 0xFA
> -#define OMAP3430_SR2_ERRMINLIMIT 0xF9
> +#define OMAP3430_SR_ERRMINLIMIT_HIGHOPP 0xF9
> +#define OMAP3430_SR_ERRMINLIMIT_LOWOPP 0xF4
>
> /* TODO:3630/OMAP4 values if it has to come from this file */
>
> diff --git a/arch/arm/mach-omap2/voltage.c b/arch/arm/mach-omap2/voltage.c
> index c0c2c17..49167c0 100644
> --- a/arch/arm/mach-omap2/voltage.c
> +++ b/arch/arm/mach-omap2/voltage.c
> @@ -19,6 +19,7 @@
> #include <linux/pm.h>
> #include <linux/delay.h>
> #include <linux/io.h>
> +#include <linux/clk.h>
>
> #include <plat/omap-pm.h>
> #include <plat/omap34xx.h>
> @@ -28,9 +29,9 @@
> #include "prm-regbits-34xx.h"
> #include "voltage.h"
>
> -#define MAX_TRIES 100
> +#define VP_IDLE_TIMEOUT 200
>
> -/**
> +/*
> * OMAP3 Voltage controller SR parameters. TODO: Pass this info as part of
> * board data or PMIC data
> */
> @@ -281,13 +282,32 @@ static void __init vp_configure(int vp_id)
> static void __init vp_reg_configure(int vp_id)
> {
> if (cpu_is_omap34xx()) {
> + struct clk *sys_ck;
> + u32 sys_clk_speed, timeout_val;
> +
> vp_reg[vp_id].vp_offs = omap3_vp_offs[vp_id];
> if (vp_id == VP1) {
> + /*
> + * OMAP3430 has error gain varying btw higher and
> + * lower opp's
> + */
> + vp_reg[vp_id].vp_errorgain = (((get_vdd1_opp() > 2) ?
> + (OMAP3_VP_CONFIG_ERRORGAIN_HIGHOPP) :
> + (OMAP3_VP_CONFIG_ERRORGAIN_LOWOPP)) <<
> + OMAP3430_ERRORGAIN_SHIFT);
> vp_reg[vp_id].vp_vddmin = (OMAP3_VP1_VLIMITTO_VDDMIN <<
> OMAP3430_VDDMIN_SHIFT);
> vp_reg[vp_id].vp_vddmax = (OMAP3_VP1_VLIMITTO_VDDMAX <<
> OMAP3430_VDDMAX_SHIFT);
> } else if (vp_id == VP2) {
> + /*
> + * OMAP3430 has error gain varying btw higher and
> + * lower opp's
> + */
> + vp_reg[vp_id].vp_errorgain = (((get_vdd2_opp() > 2) ?
> + (OMAP3_VP_CONFIG_ERRORGAIN_HIGHOPP) :
> + (OMAP3_VP_CONFIG_ERRORGAIN_LOWOPP)) <<
> + OMAP3430_ERRORGAIN_SHIFT);
> vp_reg[vp_id].vp_vddmin = (OMAP3_VP2_VLIMITTO_VDDMIN <<
> OMAP3430_VDDMIN_SHIFT);
> vp_reg[vp_id].vp_vddmax = (OMAP3_VP2_VLIMITTO_VDDMAX <<
> @@ -299,8 +319,6 @@ static void __init vp_reg_configure(int vp_id)
> }
> vp_reg[vp_id].vp_erroroffset = (OMAP3_VP_CONFIG_ERROROFFSET <<
> OMAP3430_INITVOLTAGE_SHIFT);
> - vp_reg[vp_id].vp_errorgain = (OMAP3_VP_CONFIG_ERRORGAIN <<
> - OMAP3430_ERRORGAIN_SHIFT);
> vp_reg[vp_id].vp_smpswaittimemin =
> (OMAP3_VP_VSTEPMIN_SMPSWAITTIMEMIN <<
> OMAP3430_SMPSWAITTIMEMIN_SHIFT);
> @@ -311,7 +329,18 @@ static void __init vp_reg_configure(int vp_id)
> OMAP3430_VSTEPMIN_SHIFT);
> vp_reg[vp_id].vp_stepmax = (OMAP3_VP_VSTEPMAX_VSTEPMAX <<
> OMAP3430_VSTEPMAX_SHIFT);
> - vp_reg[vp_id].vp_timeout = (OMAP3_VP_VLIMITTO_TIMEOUT <<
> + /*
> + * Use sys clk speed to convet the VP timeout in us to no of
^^^^^^
typo: convert
also, please change 'no of...' to 'number of...'
> + * clock cycles
> + */
> + sys_ck = clk_get(NULL, "sys_ck");
need to check for error here
> + sys_clk_speed = clk_get_rate(sys_ck);
> + clk_put(sys_ck);
> + /* Divide to avoid overflow */
> + sys_clk_speed /= 1000;
> + timeout_val = (sys_clk_speed * OMAP3_VP_VLIMITTO_TIMEOUT_US) /
> + 1000;
> + vp_reg[vp_id].vp_timeout = (timeout_val <<
> OMAP3430_TIMEOUT_SHIFT);
> }
> /* TODO Extend this for OMAP4 ?? Or need a separate file */
> @@ -338,7 +367,12 @@ static int vc_bypass_scale_voltage(u32 vdd, u8 target_vsel, u8 current_vsel)
> vc_cmdval0 |= (target_vsel << VC_CMD_ON_SHIFT);
> voltage_write_reg(vc_reg.vc_cmdval0_reg, vc_cmdval0);
> reg_addr = R_VDD1_SR_CONTROL;
> -
> + /* OMAP3430 has errorgain varying btw higher and lower opp's */
> + if (cpu_is_omap34xx())
> + vp_reg[vdd].vp_errorgain = (((get_vdd1_opp() > 2) ?
> + (OMAP3_VP_CONFIG_ERRORGAIN_HIGHOPP) :
> + (OMAP3_VP_CONFIG_ERRORGAIN_LOWOPP)) <<
> + OMAP3430_ERRORGAIN_SHIFT);
> } else if (vdd == VDD2_OPP) {
> u32 vc_cmdval1;
>
> @@ -347,12 +381,29 @@ static int vc_bypass_scale_voltage(u32 vdd, u8 target_vsel, u8 current_vsel)
> vc_cmdval1 |= (target_vsel << VC_CMD_ON_SHIFT);
> voltage_write_reg(vc_reg.vc_cmdval1_reg, vc_cmdval1);
> reg_addr = R_VDD2_SR_CONTROL;
> + /* OMAP3430 has errorgain varying btw higher and lower opp's */
> + if (cpu_is_omap34xx())
> + vp_reg[vdd].vp_errorgain = (((get_vdd2_opp() > 2) ?
> + (OMAP3_VP_CONFIG_ERRORGAIN_HIGHOPP) :
> + (OMAP3_VP_CONFIG_ERRORGAIN_LOWOPP)) <<
> + OMAP3430_ERRORGAIN_SHIFT);
> } else {
> pr_warning("Wrong VDD passed in vc_bypass_scale_voltage %d\n",
> vdd);
> return false;
> }
>
> + /* OMAP3430 has errorgain varying btw higher and lower opp's */
> + if (cpu_is_omap34xx()) {
> + u32 errorgain =
> + voltage_read_reg(vp_reg[vdd - 1].vp_offs.
> + vp_vpconfig_reg);
> + errorgain &= ~VP_ERRORGAIN_MASK;
> + errorgain |= vp_reg[vdd].vp_errorgain;
> +
> + voltage_write_reg(vp_reg[vdd - 1].vp_offs.vp_vpconfig_reg,
> + errorgain);
> + }
> vc_bypass_value = (target_vsel << VC_DATA_SHIFT) |
> (reg_addr << VC_REGADDR_SHIFT) |
> (R_SRI2C_SLAVE_ADDR << VC_SLAVEADDR_SHIFT);
> @@ -419,6 +470,10 @@ void omap_voltageprocessor_enable(int vp_id)
> {
> u32 vpconfig;
>
> + /* If VP is already enabled, do nothing. Return */
> + if (voltage_read_reg(vp_reg[vp_id - 1].vp_offs.vp_vpconfig_reg) &
> + VP_CONFIG_VPENABLE)
> + return;
> /*
> * This latching is required only if VC bypass method is used for
> * voltage scaling during dvfs.
> @@ -439,21 +494,29 @@ void omap_voltageprocessor_enable(int vp_id)
> */
> void omap_voltageprocessor_disable(int vp_id)
> {
> - int i = 0;
> u32 vpconfig;
> + int timeout = 0;
>
> - /* Wait for VP idle before disabling VP */
> - while ((!voltage_read_reg(vp_reg[vp_id - 1].vp_offs.vp_status_reg)) &&
> - i++ < MAX_TRIES)
> - udelay(1);
> -
> - if (i >= MAX_TRIES)
> - pr_warning("VP1 not idle, still going ahead with \
> - VP1 disable\n");
> - /* Disable VP1 */
> + /* If VP is already disabled, do nothing. Return */
> + if (!(voltage_read_reg(vp_reg[vp_id - 1].vp_offs.vp_vpconfig_reg) &
> + VP_CONFIG_VPENABLE))
> + return;
> + /* Disable VP */
> vpconfig = voltage_read_reg(vp_reg[vp_id - 1].vp_offs.vp_vpconfig_reg);
> vpconfig &= ~VP_CONFIG_VPENABLE;
> voltage_write_reg(vp_reg[vp_id - 1].vp_offs.vp_vpconfig_reg, vpconfig);
> +
> + /*
> + * Wait for VP idle Typical latency is <2us. Maximum latency is ~100us
> + */
> + while ((timeout++ < VP_IDLE_TIMEOUT) &&
> + (!(voltage_read_reg(vp_reg[vp_id - 1].vp_offs
> + .vp_status_reg))))
> + udelay(1);
another use for omap_test_timeout()
> + if (timeout >= VP_IDLE_TIMEOUT)
> + pr_warning("VP%d idle timedout\n", vp_id);
> + return;
> }
>
> /**
> diff --git a/arch/arm/mach-omap2/voltage.h b/arch/arm/mach-omap2/voltage.h
> index 64c506c..c3203c9 100644
> --- a/arch/arm/mach-omap2/voltage.h
> +++ b/arch/arm/mach-omap2/voltage.h
> @@ -22,6 +22,7 @@ extern int get_vdd2_opp(void);
> #define VP_CONFIG_INITVDD OMAP3430_INITVDD
> #define VP_FORCEUPDATE OMAP3430_FORCEUPDATE
> #define VP_CONFIG_VPENABLE OMAP3430_VPENABLE
> +#define VP_ERRORGAIN_MASK OMAP3430_ERRORGAIN_MASK
> #define VP_INITVOLTAGE_MASK OMAP3430_INITVOLTAGE_MASK
> #define VP_INITVOLTAGE_SHIFT OMAP3430_INITVOLTAGE_SHIFT
>
> @@ -52,16 +53,17 @@ extern int get_vdd2_opp(void);
> * board file or PMIC data structure
> */
> #define OMAP3_VP_CONFIG_ERROROFFSET 0x00
> -#define OMAP3_VP_CONFIG_ERRORGAIN 0x20
> -#define OMAP3_VP_VSTEPMIN_SMPSWAITTIMEMIN 0x01F4
> +#define OMAP3_VP_CONFIG_ERRORGAIN_LOWOPP 0x0C
> +#define OMAP3_VP_CONFIG_ERRORGAIN_HIGHOPP 0x18
> +#define OMAP3_VP_VSTEPMIN_SMPSWAITTIMEMIN 0x3C
> #define OMAP3_VP_VSTEPMIN_VSTEPMIN 0x1
> -#define OMAP3_VP_VSTEPMAX_SMPSWAITTIMEMAX 0x01F4
> +#define OMAP3_VP_VSTEPMAX_SMPSWAITTIMEMAX 0x3C
> #define OMAP3_VP_VSTEPMAX_VSTEPMAX 0x04
> -#define OMAP3_VP1_VLIMITTO_VDDMIN 0x0
> -#define OMAP3_VP1_VLIMITTO_VDDMAX 0x3C
> +#define OMAP3_VP1_VLIMITTO_VDDMIN 0x14
> +#define OMAP3_VP1_VLIMITTO_VDDMAX 0x42
> #define OMAP3_VP2_VLIMITTO_VDDMAX 0x2C
> -#define OMAP3_VP2_VLIMITTO_VDDMIN 0x0
> -#define OMAP3_VP_VLIMITTO_TIMEOUT 0xFFFF
> +#define OMAP3_VP2_VLIMITTO_VDDMIN 0x18
> +#define OMAP3_VP_VLIMITTO_TIMEOUT_US 0x200
>
> #define VOLTAGE_MOD OMAP3430_GR_MOD
> /* TODO OMAP4 VP register values if the same file is used for OMAP4*/
> --
> 1.7.0.rc1.33.g07cf0f
Kevin
next prev parent reply other threads:[~2010-03-03 0:54 UTC|newest]
Thread overview: 61+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-02-24 9:29 [PATCH 00/16] OMAP3: PM: Smartreflex and voltage revamp Thara Gopinath
2010-02-24 9:29 ` [PATCH 01/16] OMAP3: PM: Adding hwmod data for Smartreflex Thara Gopinath
2010-02-24 9:29 ` [PATCH 02/16] OMAP3: PM: Create list to keep track of various smartreflex instances Thara Gopinath
2010-02-24 9:29 ` [PATCH 03/16] OMAP3: PM: Convert smartreflex driver into a platform driver using hwmods and omap-device layer Thara Gopinath
2010-02-24 9:29 ` [PATCH 04/16] OMAP3: PM: Move smartreflex autocompensation enable disable hooks to PM debugfs Thara Gopinath
2010-02-24 9:29 ` [PATCH 05/16] OMAP3: PM: Export get_vdd1_opp and get_vdd2_opp from shared resource framework Thara Gopinath
2010-02-24 9:29 ` [PATCH 06/16] OMAP3: PM: Smartreflex class related changes for smartreflex.c Thara Gopinath
2010-02-24 9:29 ` [PATCH 07/16] OMAP3: PM: Adding smartreflex class 3 driver Thara Gopinath
2010-02-24 9:29 ` [PATCH 08/16] OMAP3: PM: Disabling Smartreflex across both frequency and voltage scaling during DVFS Thara Gopinath
2010-02-24 9:29 ` [PATCH 09/16] OMAP3: PM: Creating separate files for handling OMAP3 voltage related operations Thara Gopinath
2010-02-24 9:29 ` [PATCH 10/16] OMAP3: PM: Cleaning up of smartreflex header file Thara Gopinath
2010-02-24 9:29 ` [PATCH 11/16] OMAP3: PM: Configurations for Smartreflex Class 2 and Smartreflex Class 3 Thara Gopinath
2010-02-24 9:29 ` [PATCH 12/16] OMAP3: PM: Support for enabling smartreflex autocompensation by default Thara Gopinath
2010-02-24 9:29 ` [PATCH 13/16] OMAP3: PM: Correcting accessing of ERRCONFIG register in smartreflex.c Thara Gopinath
2010-02-24 9:29 ` [PATCH 14/16] OMAP3: PM: Implement latest h/w recommendations for SR and VP registers and SR VP enable disable sequence Thara Gopinath
2010-02-24 9:29 ` [PATCH 15/16] OMAP3: PM: VP force update method of voltage scaling Thara Gopinath
2010-02-24 9:29 ` [PATCH 16/16] OMAP3: PM: Enabling Smartreflex Class 3 driver by default in pm defconfig Thara Gopinath
2010-03-03 0:58 ` [PATCH 15/16] OMAP3: PM: VP force update method of voltage scaling Kevin Hilman
2010-03-05 15:22 ` Gopinath, Thara
2010-03-05 15:26 ` Felipe Contreras
2010-03-05 15:30 ` Gopinath, Thara
2010-03-05 16:22 ` Felipe Contreras
2010-03-05 18:17 ` Snipping irrelevant text from a discussion (was: "RE: [PATCH 15/16] OMAP3: PM: VP force update method of voltage scaling") Aguirre, Sergio
2010-03-05 21:18 ` Felipe Contreras
2010-03-09 1:42 ` Tony Lindgren
2010-03-09 6:51 ` Felipe Balbi
2010-03-09 15:21 ` Aguirre, Sergio
2010-03-09 18:21 ` Tony Lindgren
2010-03-03 0:54 ` Kevin Hilman [this message]
2010-03-03 0:48 ` [PATCH 12/16] OMAP3: PM: Support for enabling smartreflex autocompensation by default Kevin Hilman
2010-03-05 15:20 ` Gopinath, Thara
2010-03-03 0:37 ` [PATCH 11/16] OMAP3: PM: Configurations for Smartreflex Class 2 and Smartreflex Class 3 Kevin Hilman
2010-03-05 15:12 ` Gopinath, Thara
2010-03-05 19:20 ` Kevin Hilman
2010-03-02 20:02 ` [PATCH 09/16] OMAP3: PM: Creating separate files for handling OMAP3 voltage related operations Kevin Hilman
2010-03-05 15:17 ` Gopinath, Thara
2010-03-02 19:36 ` [PATCH 07/16] OMAP3: PM: Adding smartreflex class 3 driver Kevin Hilman
2010-03-05 15:03 ` Gopinath, Thara
2010-03-05 19:12 ` Kevin Hilman
2010-03-02 18:44 ` [PATCH 06/16] OMAP3: PM: Smartreflex class related changes for smartreflex.c Kevin Hilman
2010-03-05 15:00 ` Gopinath, Thara
2010-03-05 18:29 ` Kevin Hilman
2010-03-02 23:37 ` Kevin Hilman
2010-03-02 23:52 ` Kevin Hilman
2010-03-05 15:18 ` Gopinath, Thara
2010-03-05 18:30 ` Kevin Hilman
2010-03-02 18:28 ` [PATCH 04/16] OMAP3: PM: Move smartreflex autocompensation enable disable hooks to PM debugfs Kevin Hilman
2010-02-25 2:39 ` [PATCH 03/16] OMAP3: PM: Convert smartreflex driver into a platform driver using hwmods and omap-device layer ambresh
2010-03-02 18:28 ` Kevin Hilman
2010-03-05 14:26 ` Gopinath, Thara
2010-03-12 9:48 ` Gopinath, Thara
2010-03-13 0:36 ` Kevin Hilman
2010-03-15 19:00 ` Tony Lindgren
2010-03-03 0:02 ` Kevin Hilman
2010-02-25 1:42 ` [PATCH 02/16] OMAP3: PM: Create list to keep track of various smartreflex instances ambresh
2010-03-02 17:40 ` Kevin Hilman
2010-02-26 23:21 ` Mike Turquette
2010-03-02 17:39 ` Kevin Hilman
2010-02-24 16:52 ` [PATCH 01/16] OMAP3: PM: Adding hwmod data for Smartreflex Mike Turquette
2010-03-06 0:45 ` Kevin Hilman
2010-03-06 0:58 ` [PATCH 00/16] OMAP3: PM: Smartreflex and voltage revamp Kevin Hilman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87y6iap6lg.fsf@deeprootsystems.com \
--to=khilman@deeprootsystems.com \
--cc=b-cousson@ti.com \
--cc=linux-omap@vger.kernel.org \
--cc=nm@ti.com \
--cc=paul@pwsan.com \
--cc=sawant@ti.com \
--cc=thara@ti.com \
--cc=vishwanath.bs@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox