* OMAP3: USB: EHCI broken on 3.5?
@ 2012-07-31 12:42 Joe Woodward
2012-08-02 8:18 ` Joe Woodward
2012-08-06 18:21 ` Kevin Hilman
0 siblings, 2 replies; 4+ messages in thread
From: Joe Woodward @ 2012-07-31 12:42 UTC (permalink / raw)
To: linux-omap@vger.kernel.org
I have a GUMSTIX Overo AirSTORM (AM3703-based).
When running a 3.4 kernel the USB host works just fine!
However when switching to 3.5 I get a few new warning messages and USB host no longer works.
dmesg log after successfully loading the module (modprobe echi-hcd) on 3.4:
[ 23.424499] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 23.431427] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
[ 23.431732] ehci-omap ehci-omap.0: failed to get ehci port1 regulator
[ 23.431762] gpio_request: gpio-183 (USB2 PHY reset) status -16
[ 24.433471] ehci-omap ehci-omap.0: phy reset operation timed out
[ 24.433502] ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3
[ 24.433532] ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
[ 24.433532] ehci-omap ehci-omap.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 24.433563] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 24.440063] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[ 24.448120] ehci-omap ehci-omap.0: park 0
[ 24.448181] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 24.454162] ehci-omap ehci-omap.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[ 24.474517] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 24.481597] usb usb1: default language 0x0409
[ 24.481658] usb usb1: udev 1, busnum 1, minor = 0
[ 24.481689] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 24.488830] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 24.496398] usb usb1: Product: OMAP-EHCI Host Controller
[ 24.501953] usb usb1: Manufacturer: Linux 3.4.0 ehci_hcd
[ 24.507537] usb usb1: SerialNumber: ehci-omap.0
[ 24.528747] usb usb1: usb_probe_device
[ 24.528778] usb usb1: configuration #1 chosen from 1 choice
[ 24.529479] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 24.530212] hub 1-0:1.0: usb_probe_interface
[ 24.530242] hub 1-0:1.0: usb_probe_interface - got id
[ 24.530303] hub 1-0:1.0: USB hub found
[ 24.534362] hub 1-0:1.0: 3 ports detected
[ 24.538635] hub 1-0:1.0: standalone hub
[ 24.538635] hub 1-0:1.0: individual port power switching
[ 24.538665] hub 1-0:1.0: individual port over-current protection
[ 24.538665] hub 1-0:1.0: power on to power good time: 20ms
[ 24.539031] hub 1-0:1.0: local power source is good
[ 24.539062] hub 1-0:1.0: enabling power on all ports
[ 24.540008] ehci-omap ehci-omap.0: ...powerup ports...
[ 24.637634] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 27.013153] hub 1-0:1.0: hub_suspend
[ 27.015319] usb usb1: bus auto-suspend, wakeup 1
[ 27.015411] ehci-omap ehci-omap.0: suspend root hub
dmesg log after failing to load the module (modprobe echi-hcd) on 3.5:
[ 83.900115] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 83.907043] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
[ 83.907379] ehci-omap ehci-omap.0: failed to get ehci port1 regulator
[ 84.912445] ehci-omap ehci-omap.0: phy reset operation timed out
[ 84.912475] ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3
[ 84.912475] ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
[ 84.912506] ehci-omap ehci-omap.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 84.912506] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
[ 84.919097] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
[ 84.927154] ehci-omap ehci-omap.0: park 0
[ 84.927215] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
[ 84.933197] ehci-omap ehci-omap.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[ 84.946655] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
[ 84.953796] usb usb1: default language 0x0409
[ 84.953887] usb usb1: udev 1, busnum 1, minor = 0
[ 84.953887] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 84.961059] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 84.968627] usb usb1: Product: OMAP-EHCI Host Controller
[ 84.974151] usb usb1: Manufacturer: Linux 3.5.0 ehci_hcd
[ 84.979736] usb usb1: SerialNumber: ehci-omap.0
[ 84.987518] usb usb1: usb_probe_device
[ 84.987548] usb usb1: configuration #1 chosen from 1 choice
[ 84.988220] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 84.988891] hub 1-0:1.0: usb_probe_interface
[ 84.988922] hub 1-0:1.0: usb_probe_interface - got id
[ 84.988983] hub 1-0:1.0: USB hub found
[ 84.993133] hub 1-0:1.0: 3 ports detected
[ 84.997344] hub 1-0:1.0: standalone hub
[ 84.997344] hub 1-0:1.0: individual port power switching
[ 84.997344] hub 1-0:1.0: individual port over-current protection
[ 84.997375] hub 1-0:1.0: power on to power good time: 20ms
[ 84.997711] hub 1-0:1.0: local power source is good
[ 84.997741] hub 1-0:1.0: enabling power on all ports
[ 84.998840] ehci-omap ehci-omap.0: ...powerup ports...
[ 85.030212] ehci-omap ehci-omap.0: utmi_p1_gfclk failed error:-2
[ 85.036560] ehci-omap: probe of ehci-omap.0 failed with error -2
[ 85.093658] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
[ 87.093780] hub 1-0:1.0: hub_suspend
[ 87.095977] usb usb1: bus auto-suspend, wakeup 1
[ 87.096099] platform ehci-omap.0: suspend root hub
You can see that the following two new warnings are produced:
[ 85.030212] ehci-omap ehci-omap.0: utmi_p1_gfclk failed error:-2
[ 85.036560] ehci-omap: probe of ehci-omap.0 failed with error -2
If I (rather crudely) take ehci-omap.c from 3.4, drop it in to 3.5 and re-build then 3.5 works fine.
Any ideas?
Cheers,
Joe Woodward
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: OMAP3: USB: EHCI broken on 3.5?
2012-07-31 12:42 OMAP3: USB: EHCI broken on 3.5? Joe Woodward
@ 2012-08-02 8:18 ` Joe Woodward
2012-08-06 18:21 ` Kevin Hilman
1 sibling, 0 replies; 4+ messages in thread
From: Joe Woodward @ 2012-08-02 8:18 UTC (permalink / raw)
To: Joe Woodward, linux-omap; +Cc: balbi, linux-usb
(Adding in the USB mailing list)...
It seems that the clocks are registered with a .dev_id of "usbhs_omap" on OMAP3xxx, but not OMAP4xxx, and that this causes the clk_get() in ehci-omap.c to fail.
The following fixes the problem for me, but I've no idea if this is the correct fix or not?
(sorry if the patch is mangled, using a naff webmail client).
--- a/arch/arm/mach-omap2/clock3xxx_data.c 2012-07-21 21:58:29.000000000 +0100
+++ b/arch/arm/mach-omap2/clock3xxx_data.c 2012-08-02 09:07:58.205633679 +0100
@@ -3391,15 +3391,15 @@
CLK(NULL, "usbhost_48m_fck", &usbhost_48m_fck, CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
CLK(NULL, "usbhost_ick", &usbhost_ick, CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
CLK("usbhs_omap", "usbhost_ick", &usbhost_ick, CK_3430ES2PLUS | CK_AM35XX | CK_36XX),
- CLK("usbhs_omap", "utmi_p1_gfclk", &dummy_ck, CK_3XXX),
- CLK("usbhs_omap", "utmi_p2_gfclk", &dummy_ck, CK_3XXX),
- CLK("usbhs_omap", "xclk60mhsp1_ck", &dummy_ck, CK_3XXX),
- CLK("usbhs_omap", "xclk60mhsp2_ck", &dummy_ck, CK_3XXX),
- CLK("usbhs_omap", "usb_host_hs_utmi_p1_clk", &dummy_ck, CK_3XXX),
- CLK("usbhs_omap", "usb_host_hs_utmi_p2_clk", &dummy_ck, CK_3XXX),
- CLK("usbhs_omap", "usb_tll_hs_usb_ch0_clk", &dummy_ck, CK_3XXX),
- CLK("usbhs_omap", "usb_tll_hs_usb_ch1_clk", &dummy_ck, CK_3XXX),
- CLK("usbhs_omap", "init_60m_fclk", &dummy_ck, CK_3XXX),
+ CLK(NULL, "utmi_p1_gfclk", &dummy_ck, CK_3XXX),
+ CLK(NULL, "utmi_p2_gfclk", &dummy_ck, CK_3XXX),
+ CLK(NULL, "xclk60mhsp1_ck", &dummy_ck, CK_3XXX),
+ CLK(NULL, "xclk60mhsp2_ck", &dummy_ck, CK_3XXX),
+ CLK(NULL, "usb_host_hs_utmi_p1_clk", &dummy_ck, CK_3XXX),
+ CLK(NULL, "usb_host_hs_utmi_p2_clk", &dummy_ck, CK_3XXX),
+ CLK(NULL, "usb_tll_hs_usb_ch0_clk", &dummy_ck, CK_3XXX),
+ CLK(NULL, "usb_tll_hs_usb_ch1_clk", &dummy_ck, CK_3XXX),
+ CLK(NULL, "init_60m_fclk", &dummy_ck, CK_3XXX),
CLK(NULL, "usim_fck", &usim_fck, CK_3430ES2PLUS | CK_36XX),
CLK(NULL, "gpt1_fck", &gpt1_fck, CK_3XXX),
CLK(NULL, "wkup_32k_fck", &wkup_32k_fck, CK_3XXX),
Cheers,
Joe
-----Original Message-----
From: "Joe Woodward" <jw@terrafix.co.uk>
To: "linux-omap@vger.kernel.org" <linux-omap@vger.kernel.org>
Date: Tue, 31 Jul 2012 13:42:07 +0100
Subject: OMAP3: USB: EHCI broken on 3.5?
> I have a GUMSTIX Overo AirSTORM (AM3703-based).
>
> When running a 3.4 kernel the USB host works just fine!
>
> However when switching to 3.5 I get a few new warning messages and USB
> host no longer works.
>
> dmesg log after successfully loading the module (modprobe echi-hcd) on
> 3.4:
> [ 23.424499] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
> Driver
> [ 23.431427] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
> [ 23.431732] ehci-omap ehci-omap.0: failed to get ehci port1
> regulator
> [ 23.431762] gpio_request: gpio-183 (USB2 PHY reset) status -16
> [ 24.433471] ehci-omap ehci-omap.0: phy reset operation timed out
> [ 24.433502] ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0
> cc=1 pcc=3 ordered ports=3
> [ 24.433532] ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1
> uframes 256/512/1024 park
> [ 24.433532] ehci-omap ehci-omap.0: reset command 0080b02 park=3
> ithresh=8 period=1024 Reset HALT
> [ 24.433563] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> [ 24.440063] ehci-omap ehci-omap.0: new USB bus registered, assigned
> bus number 1
> [ 24.448120] ehci-omap ehci-omap.0: park 0
> [ 24.448181] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> [ 24.454162] ehci-omap ehci-omap.0: init command 0010005 (park)=0
> ithresh=1 period=512 RUN
> [ 24.474517] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> [ 24.481597] usb usb1: default language 0x0409
> [ 24.481658] usb usb1: udev 1, busnum 1, minor = 0
> [ 24.481689] usb usb1: New USB device found, idVendor=1d6b,
> idProduct=0002
> [ 24.488830] usb usb1: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 24.496398] usb usb1: Product: OMAP-EHCI Host Controller
> [ 24.501953] usb usb1: Manufacturer: Linux 3.4.0 ehci_hcd
> [ 24.507537] usb usb1: SerialNumber: ehci-omap.0
> [ 24.528747] usb usb1: usb_probe_device
> [ 24.528778] usb usb1: configuration #1 chosen from 1 choice
> [ 24.529479] usb usb1: adding 1-0:1.0 (config #1, interface 0)
> [ 24.530212] hub 1-0:1.0: usb_probe_interface
> [ 24.530242] hub 1-0:1.0: usb_probe_interface - got id
> [ 24.530303] hub 1-0:1.0: USB hub found
> [ 24.534362] hub 1-0:1.0: 3 ports detected
> [ 24.538635] hub 1-0:1.0: standalone hub
> [ 24.538635] hub 1-0:1.0: individual port power switching
> [ 24.538665] hub 1-0:1.0: individual port over-current protection
> [ 24.538665] hub 1-0:1.0: power on to power good time: 20ms
> [ 24.539031] hub 1-0:1.0: local power source is good
> [ 24.539062] hub 1-0:1.0: enabling power on all ports
> [ 24.540008] ehci-omap ehci-omap.0: ...powerup ports...
> [ 24.637634] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
> [ 27.013153] hub 1-0:1.0: hub_suspend
> [ 27.015319] usb usb1: bus auto-suspend, wakeup 1
> [ 27.015411] ehci-omap ehci-omap.0: suspend root hub
>
>
> dmesg log after failing to load the module (modprobe echi-hcd) on 3.5:
> [ 83.900115] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI)
> Driver
> [ 83.907043] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
> [ 83.907379] ehci-omap ehci-omap.0: failed to get ehci port1
> regulator
> [ 84.912445] ehci-omap ehci-omap.0: phy reset operation timed out
> [ 84.912475] ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0
> cc=1 pcc=3 ordered ports=3
> [ 84.912475] ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1
> uframes 256/512/1024 park
> [ 84.912506] ehci-omap ehci-omap.0: reset command 0080b02 park=3
> ithresh=8 period=1024 Reset HALT
> [ 84.912506] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> [ 84.919097] ehci-omap ehci-omap.0: new USB bus registered, assigned
> bus number 1
> [ 84.927154] ehci-omap ehci-omap.0: park 0
> [ 84.927215] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> [ 84.933197] ehci-omap ehci-omap.0: init command 0010005 (park)=0
> ithresh=1 period=512 RUN
> [ 84.946655] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> [ 84.953796] usb usb1: default language 0x0409
> [ 84.953887] usb usb1: udev 1, busnum 1, minor = 0
> [ 84.953887] usb usb1: New USB device found, idVendor=1d6b,
> idProduct=0002
> [ 84.961059] usb usb1: New USB device strings: Mfr=3, Product=2,
> SerialNumber=1
> [ 84.968627] usb usb1: Product: OMAP-EHCI Host Controller
> [ 84.974151] usb usb1: Manufacturer: Linux 3.5.0 ehci_hcd
> [ 84.979736] usb usb1: SerialNumber: ehci-omap.0
> [ 84.987518] usb usb1: usb_probe_device
> [ 84.987548] usb usb1: configuration #1 chosen from 1 choice
> [ 84.988220] usb usb1: adding 1-0:1.0 (config #1, interface 0)
> [ 84.988891] hub 1-0:1.0: usb_probe_interface
> [ 84.988922] hub 1-0:1.0: usb_probe_interface - got id
> [ 84.988983] hub 1-0:1.0: USB hub found
> [ 84.993133] hub 1-0:1.0: 3 ports detected
> [ 84.997344] hub 1-0:1.0: standalone hub
> [ 84.997344] hub 1-0:1.0: individual port power switching
> [ 84.997344] hub 1-0:1.0: individual port over-current protection
> [ 84.997375] hub 1-0:1.0: power on to power good time: 20ms
> [ 84.997711] hub 1-0:1.0: local power source is good
> [ 84.997741] hub 1-0:1.0: enabling power on all ports
> [ 84.998840] ehci-omap ehci-omap.0: ...powerup ports...
> [ 85.030212] ehci-omap ehci-omap.0: utmi_p1_gfclk failed error:-2
> [ 85.036560] ehci-omap: probe of ehci-omap.0 failed with error -2
> [ 85.093658] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
> [ 87.093780] hub 1-0:1.0: hub_suspend
> [ 87.095977] usb usb1: bus auto-suspend, wakeup 1
> [ 87.096099] platform ehci-omap.0: suspend root hub
>
> You can see that the following two new warnings are produced:
> [ 85.030212] ehci-omap ehci-omap.0: utmi_p1_gfclk failed error:-2
> [ 85.036560] ehci-omap: probe of ehci-omap.0 failed with error -2
>
> If I (rather crudely) take ehci-omap.c from 3.4, drop it in to 3.5 and
> re-build then 3.5 works fine.
>
> Any ideas?
>
> Cheers,
> Joe Woodward
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap"
> in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: OMAP3: USB: EHCI broken on 3.5?
2012-07-31 12:42 OMAP3: USB: EHCI broken on 3.5? Joe Woodward
2012-08-02 8:18 ` Joe Woodward
@ 2012-08-06 18:21 ` Kevin Hilman
2012-08-07 6:10 ` Felipe Balbi
1 sibling, 1 reply; 4+ messages in thread
From: Kevin Hilman @ 2012-08-06 18:21 UTC (permalink / raw)
To: Joe Woodward; +Cc: linux-omap@vger.kernel.org
Hi Joe,
"Joe Woodward" <jw@terrafix.co.uk> writes:
> I have a GUMSTIX Overo AirSTORM (AM3703-based).
>
> When running a 3.4 kernel the USB host works just fine!
>
> However when switching to 3.5 I get a few new warning messages and USB host no longer works.
As usual, thanks for the bug/problem reports.
EHCI is broken in many ways in v3.5. Since the maintainers were not
fixing the problems (specifically the PM problems which broke PM for the
rest of the SoC too), I requested it be disabled by default in
omap2plus_defconfig.
Kesheva sent out a large revert patch, and Russ Dill sent out an
alternative set of 2 patches that were more targetted fixes, but I lost
track of the final resolution there (if any.)
Kevin
> dmesg log after successfully loading the module (modprobe echi-hcd) on 3.4:
> [ 23.424499] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 23.431427] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
> [ 23.431732] ehci-omap ehci-omap.0: failed to get ehci port1 regulator
> [ 23.431762] gpio_request: gpio-183 (USB2 PHY reset) status -16
> [ 24.433471] ehci-omap ehci-omap.0: phy reset operation timed out
> [ 24.433502] ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3
> [ 24.433532] ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
> [ 24.433532] ehci-omap ehci-omap.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
> [ 24.433563] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> [ 24.440063] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
> [ 24.448120] ehci-omap ehci-omap.0: park 0
> [ 24.448181] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> [ 24.454162] ehci-omap ehci-omap.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
> [ 24.474517] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> [ 24.481597] usb usb1: default language 0x0409
> [ 24.481658] usb usb1: udev 1, busnum 1, minor = 0
> [ 24.481689] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 24.488830] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 24.496398] usb usb1: Product: OMAP-EHCI Host Controller
> [ 24.501953] usb usb1: Manufacturer: Linux 3.4.0 ehci_hcd
> [ 24.507537] usb usb1: SerialNumber: ehci-omap.0
> [ 24.528747] usb usb1: usb_probe_device
> [ 24.528778] usb usb1: configuration #1 chosen from 1 choice
> [ 24.529479] usb usb1: adding 1-0:1.0 (config #1, interface 0)
> [ 24.530212] hub 1-0:1.0: usb_probe_interface
> [ 24.530242] hub 1-0:1.0: usb_probe_interface - got id
> [ 24.530303] hub 1-0:1.0: USB hub found
> [ 24.534362] hub 1-0:1.0: 3 ports detected
> [ 24.538635] hub 1-0:1.0: standalone hub
> [ 24.538635] hub 1-0:1.0: individual port power switching
> [ 24.538665] hub 1-0:1.0: individual port over-current protection
> [ 24.538665] hub 1-0:1.0: power on to power good time: 20ms
> [ 24.539031] hub 1-0:1.0: local power source is good
> [ 24.539062] hub 1-0:1.0: enabling power on all ports
> [ 24.540008] ehci-omap ehci-omap.0: ...powerup ports...
> [ 24.637634] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
> [ 27.013153] hub 1-0:1.0: hub_suspend
> [ 27.015319] usb usb1: bus auto-suspend, wakeup 1
> [ 27.015411] ehci-omap ehci-omap.0: suspend root hub
>
>
> dmesg log after failing to load the module (modprobe echi-hcd) on 3.5:
> [ 83.900115] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> [ 83.907043] ehci_hcd: block sizes: qh 64 qtd 96 itd 160 sitd 96
> [ 83.907379] ehci-omap ehci-omap.0: failed to get ehci port1 regulator
> [ 84.912445] ehci-omap ehci-omap.0: phy reset operation timed out
> [ 84.912475] ehci-omap ehci-omap.0: reset hcs_params 0x1313 dbg=0 cc=1 pcc=3 ordered ports=3
> [ 84.912475] ehci-omap ehci-omap.0: reset hcc_params 0016 thresh 1 uframes 256/512/1024 park
> [ 84.912506] ehci-omap ehci-omap.0: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
> [ 84.912506] ehci-omap ehci-omap.0: OMAP-EHCI Host Controller
> [ 84.919097] ehci-omap ehci-omap.0: new USB bus registered, assigned bus number 1
> [ 84.927154] ehci-omap ehci-omap.0: park 0
> [ 84.927215] ehci-omap ehci-omap.0: irq 77, io mem 0x48064800
> [ 84.933197] ehci-omap ehci-omap.0: init command 0010005 (park)=0 ithresh=1 period=512 RUN
> [ 84.946655] ehci-omap ehci-omap.0: USB 2.0 started, EHCI 1.00
> [ 84.953796] usb usb1: default language 0x0409
> [ 84.953887] usb usb1: udev 1, busnum 1, minor = 0
> [ 84.953887] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
> [ 84.961059] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
> [ 84.968627] usb usb1: Product: OMAP-EHCI Host Controller
> [ 84.974151] usb usb1: Manufacturer: Linux 3.5.0 ehci_hcd
> [ 84.979736] usb usb1: SerialNumber: ehci-omap.0
> [ 84.987518] usb usb1: usb_probe_device
> [ 84.987548] usb usb1: configuration #1 chosen from 1 choice
> [ 84.988220] usb usb1: adding 1-0:1.0 (config #1, interface 0)
> [ 84.988891] hub 1-0:1.0: usb_probe_interface
> [ 84.988922] hub 1-0:1.0: usb_probe_interface - got id
> [ 84.988983] hub 1-0:1.0: USB hub found
> [ 84.993133] hub 1-0:1.0: 3 ports detected
> [ 84.997344] hub 1-0:1.0: standalone hub
> [ 84.997344] hub 1-0:1.0: individual port power switching
> [ 84.997344] hub 1-0:1.0: individual port over-current protection
> [ 84.997375] hub 1-0:1.0: power on to power good time: 20ms
> [ 84.997711] hub 1-0:1.0: local power source is good
> [ 84.997741] hub 1-0:1.0: enabling power on all ports
> [ 84.998840] ehci-omap ehci-omap.0: ...powerup ports...
> [ 85.030212] ehci-omap ehci-omap.0: utmi_p1_gfclk failed error:-2
> [ 85.036560] ehci-omap: probe of ehci-omap.0 failed with error -2
> [ 85.093658] hub 1-0:1.0: state 7 ports 3 chg 0000 evt 0000
> [ 87.093780] hub 1-0:1.0: hub_suspend
> [ 87.095977] usb usb1: bus auto-suspend, wakeup 1
> [ 87.096099] platform ehci-omap.0: suspend root hub
>
> You can see that the following two new warnings are produced:
> [ 85.030212] ehci-omap ehci-omap.0: utmi_p1_gfclk failed error:-2
> [ 85.036560] ehci-omap: probe of ehci-omap.0 failed with error -2
>
> If I (rather crudely) take ehci-omap.c from 3.4, drop it in to 3.5 and re-build then 3.5 works fine.
>
> Any ideas?
>
> Cheers,
> Joe Woodward
>
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-omap" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: OMAP3: USB: EHCI broken on 3.5?
2012-08-06 18:21 ` Kevin Hilman
@ 2012-08-07 6:10 ` Felipe Balbi
0 siblings, 0 replies; 4+ messages in thread
From: Felipe Balbi @ 2012-08-07 6:10 UTC (permalink / raw)
To: Kevin Hilman; +Cc: Joe Woodward, linux-omap@vger.kernel.org
[-- Attachment #1: Type: text/plain, Size: 908 bytes --]
On Mon, Aug 06, 2012 at 11:21:27AM -0700, Kevin Hilman wrote:
> Hi Joe,
>
> "Joe Woodward" <jw@terrafix.co.uk> writes:
>
> > I have a GUMSTIX Overo AirSTORM (AM3703-based).
> >
> > When running a 3.4 kernel the USB host works just fine!
> >
> > However when switching to 3.5 I get a few new warning messages and USB host no longer works.
>
> As usual, thanks for the bug/problem reports.
>
> EHCI is broken in many ways in v3.5. Since the maintainers were not
> fixing the problems (specifically the PM problems which broke PM for the
> rest of the SoC too), I requested it be disabled by default in
> omap2plus_defconfig.
>
> Kesheva sent out a large revert patch, and Russ Dill sent out an
> alternative set of 2 patches that were more targetted fixes, but I lost
> track of the final resolution there (if any.)
Alan Stern asked to wait for his patches first...
--
balbi
[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2012-08-07 6:14 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-07-31 12:42 OMAP3: USB: EHCI broken on 3.5? Joe Woodward
2012-08-02 8:18 ` Joe Woodward
2012-08-06 18:21 ` Kevin Hilman
2012-08-07 6:10 ` Felipe Balbi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).