From mboxrd@z Thu Jan 1 00:00:00 1970 From: "Craig D. Lansing" Subject: [parisc-linux] J2240 - Almost there.... Date: Fri, 30 Dec 2005 10:51:22 -0500 Message-ID: <000101c60d58$e249ac40$3401a8c0@POGO> Mime-Version: 1.0 Content-Type: multipart/mixed; boundary="===============1665340200==" To: Return-Path: List-Id: parisc-linux developers list List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Errors-To: parisc-linux-bounces@lists.parisc-linux.org This is a multi-part message in MIME format. --===============1665340200== Content-Type: multipart/alternative; boundary="----=_NextPart_000_0002_01C60D2E.F973A440" This is a multi-part message in MIME format. ------=_NextPart_000_0002_01C60D2E.F973A440 Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit I have an old J2240 w/ p1120 console that I was going to throw away, but decided to load the most recent PA-RISC Linux instead. I had loaded and gotten it running from the PA-RISC project several years ago. Using the ISO's from 12/19/05 I was able to successfully install on one of the hdd's (FWSCSI.5.0), but cannot boot to a prompt. When booting from path FWSCSI.5.0 I get the 2 Tux images, a long list of console output, and get the point below and it freezes. I have tried booting using a serial console, but cannot get connected to the serial port. Any ideas on how to proceed from here? End of console output: ---------------------------------------------------------------------------- -------------------------------------------------------- Starting hotplug subsystem: pci tulip: already loaded defxx.c:v1.06 2003/08/04 Lawrence V. Stephani and others fddi%d: DEFPA at I/O addr = 0x100, IRQ = 96, Hardware addr = 58-B0-60-00-00-00 ---------------------------------------------------------------------------- --------------------------------------------------------- Other info.: SESCSI.3.0 = HP C1537A Tape SESCSI.2.0 = Toshiba CD-ROM (used for install) FWSCSI.6.0 = IBM HDD (HP-UX 10.0) FWSCSI.5.0 = IBM HDD (Linux) ------=_NextPart_000_0002_01C60D2E.F973A440 Content-Type: text/html; charset="us-ascii" Content-Transfer-Encoding: quoted-printable

I have an old J2240 w/ p1120 console that I was going = to throw away, but decided to load the most recent PA-RISC Linux = instead.  I had loaded and gotten it running from the PA-RISC project several years ago.  Using the ISO’s from 12/19/05 I was able to = successfully install on one of the hdd’s (FWSCSI.5.0), but cannot boot to a = prompt. When booting from path FWSCSI.5.0 I get the 2 Tux images, a long list of console output, and get the point below and it freezes.  I have = tried booting using a serial console, but cannot get connected to the serial port.  Any ideas on how to proceed from = here?

 

End of console output:

------------------------------------------------------= -------------------------------------------------------------------------= -----

Starting hotplug = subsystem:

         =    pci

         =             &= nbsp;  tulip: already loaded

defxx.c:v1.06 2003/08/04 Lawrence V. Stephani and = others

fddi%d: DEFPA at I/O addr =3D 0x100, IRQ =3D 96, = Hardware addr =3D 58-B0-60-00-00-00

------------------------------------------------------= -------------------------------------------------------------------------= ------

 

Other info.:

SESCSI.3.0 =3D HP C1537A = Tape

SESCSI.2.0 =3D Toshiba CD-ROM (used for = install)

FWSCSI.6.0 =3D IBM HDD (HP-UX = 10.0)

FWSCSI.5.0 =3D IBM HDD = (Linux)

 

 

 

 

 

------=_NextPart_000_0002_01C60D2E.F973A440-- --===============1665340200== Content-Type: text/plain; charset="us-ascii" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit Content-Disposition: inline _______________________________________________ parisc-linux mailing list parisc-linux@lists.parisc-linux.org http://lists.parisc-linux.org/mailman/listinfo/parisc-linux --===============1665340200==--