Re: Gentoo boot on C8000 (was: Re: PARISC Linux website and status update)

[James Bottomley <James.Bottomley@HansenPartnership.com>]

On Thu, 2013-04-25 at 21:06 +0200, Ulrich Teichert wrote:
> Hi,
> 
> >> And that's it. Well, the ISO *is* an experimental one ;-) Any idea what
> >> to try?
> >
> >video=radeonfb:off
> 
> Right, that got it to boot ;-) But it failed to recognize my hard disk:
> 
> [   15.020000] Fusion MPT base driver 3.04.20
> [   15.072000] Copyright (c) 1999-2008 LSI Corporation
> [   15.136000] Fusion MPT SPI Host driver 3.04.20
> [   15.220000] mptbase: ioc0: Initiating bringup
> [   15.760000] ioc0: LSI53C1030 B2: Capabilities={Initiator,Target}
> [   16.328000] scsi0 : ioc0: LSI53C1030 B2, FwRev=01032341h, Ports=1, MaxQ=255, IRQ=66
> [   43.872000] mptscsih: ioc0: attempting task abort! (sc=000000007f29e300)
> [   43.960000] scsi 0:0:6:0: CDB: 
> [   44.000000] cdb[0]=0x12: 12 00 00 00 24 00
> [   54.176000] mptscsih: ioc0: WARNING - Issuing Reset from mptscsih_IssueTaskMgmt!! doorbell=0x24000000
> [   55.584000] mptscsih: ioc0: task abort: SUCCESS (rv=2002) (sc=000000007f29e300)
> [   55.680000] scsi target0:0:6: asynchronous
> [   55.928000] mptscsih: ioc0: attempting target reset! (sc=000000007f29e300)
> [   56.020000] scsi 0:0:6:0: CDB: 
> [   56.060000] cdb[0]=0x12: 12 00 00 00 24 00
> [   56.476000] mptscsih: ioc0: target reset: SUCCESS (sc=000000007f29e300)
> [   56.812000] mptscsih: ioc0: attempting bus reset! (sc=000000007f29e300)
> [   56.900000] scsi 0:0:6:0: CDB: 
> [   56.944000] cdb[0]=0x12: 12 00 00 00 24 00
> [   57.632000] mptscsih: ioc0: bus reset: SUCCESS (sc=000000007f29e300)
> [   67.968000] mptscsih: ioc0: attempting host reset! (sc=000000007f29e300)
> [   68.816000] mptscsih: ioc0: host reset: SUCCESS (sc=000000007f29e300)
> [   68.900000] scsi target0:0:6: asynchronous
> [   79.152000] scsi 0:0:6:0: Device offlined - not ready after error recovery
> [   81.268000] mptbase: ioc1: Initiating bringup
> [   81.808000] ioc1: LSI53C1030 B2: Capabilities={Initiator,Target}
> [   82.376000] scsi1 : ioc1: LSI53C1030 B2, FwRev=01032341h, Ports=1, MaxQ=255, IRQ=67
> 
> Which is a bit strange as I can boot HPUX from it just fine. Is that a
> common problem? Or should I just try another disk? E1000 ethernet support
> is OK and running, though,

That one looks very much like an interrupt routing problem ... the full
log might give more diagnostic information.

James