From mboxrd@z Thu Jan 1 00:00:00 1970 From: Heiner991@gmx.de Subject: [parisc-linux] B1000 freeze after sym0: Date: Wed, 14 Dec 2005 13:16:21 +0100 (MET) Message-ID: <17461.1134562581@www66.gmx.net> Mime-Version: 1.0 Content-Type: text/plain; charset="us-ascii" To: parisc-linux@lists.parisc-linux.org Return-Path: List-Id: parisc-linux developers list List-Unsubscribe: , List-Archive: List-Post: List-Help: List-Subscribe: , Errors-To: parisc-linux-bounces@lists.parisc-linux.org Hi! I installed Debian 3.1_r0 on my B1000, but now i got problems at boot. The machine hangs after the following message: [...] NET: Registered protocol family 1 sym0: <896> rev 0x4 at pci 0000:00:0f.0 irq 65 sym0: No NVRAM, ID 7, Fast-40, SE, parity checking After that it does not react to any keyboard input, even the power button doesn't work, i have to pull the power cord. The strange thing is: if i search for bootable devices in the boot menu, and select the harddrive (boot p1), everything works fine and the machine boots to shell. I want to use the B1000 without keyboard an monitor, so this is not an option an on every boot. Any suggestions? Perhaps a few PALO options i dont know? Thanks in advance, Oliver Attached: /etc/palo.conf, partition table, dmesg from a working boot /etc/palo.conf --commandline=2/vmlinux root=/dev/sda4 initrd=2/initrd.img HOME=/ --recoverykernel=/boot/vmlinux-2.6.8-2-32-smp --init-partitioned=/dev/sda fdisk /dev/sda -l Disk /dev/sda: 9100 MB, 9100044288 bytes 255 heads, 63 sectors/track, 1106 cylinders Units = cylinders of 16065 * 512 = 8225280 bytes Device Boot Start End Blocks Id System /dev/sda1 * 1 4 32098+ f0 Linux/PA-RISC boot /dev/sda2 5 8 32130 83 Linux /dev/sda3 1045 1106 498015 82 Linux swap /Solaris /dev/sda4 9 1044 8321670 83 Linux Partition table entries are not in disk order dmesg: Linux version 2.6.8-2-32-smp (kyle@caradhras) (gcc version 3.3.5 (Debian 1:3.3.5-7)) #1 SMP Mon Feb 7 22:19:10 EST 2005 FP[0] enabled: Rev 1 Model 16 The 32-bit Kernel has started... Determining PDC firmware type: System Map. model 00005bc0 00000481 00000000 00000002 7802fefc 100000f0 00000008 000000b2 000000b2 vers 00000203 CPUID vers 17 rev 7 (0x00000227) capabilities 0x3 model 9000/785/B1000 Total Memory: 256 Mb initrd: 1fb29000-1ffee000 initrd: reserving 0fb29000-0ffee000 (mem_max 10000000) On node 0 totalpages: 65536 DMA zone: 65536 pages, LIFO batch:16 Normal zone: 0 pages, LIFO batch:1 HighMem zone: 0 pages, LIFO batch:1 LCD display at f05d0008,f05d0000 registered SMP: bootstrap CPU ID is 0 Built 1 zonelists Kernel command line: root=/dev/sda4 HOME=/ console=tty0 sti=10/6/2/0 sti_font=VGA8x16 TERM=linux palo_kernel=2/vmlinux PID hash table entries: 16 (order 4: 128 bytes) Console: colour dummy device 160x64 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 262144k available Calibrating delay loop... 598.01 BogoMIPS Security Scaffold v1.0.0 initialized Capability LSM initialized Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Brought up 1 CPUs CPU0: online domain 0: span ffffffff groups: 00000001 00000002 00000004 00000008 00000010 00000020 00000040 00000080 00000100 00000200 00000400 00000800 00001000 00002000 00004000 00008000 00010000 00020000 00040000 00080000 00100000 00200000 00400000 00800000 01000000 02000000 04000000 08000000 10000000 20000000 40000000 80000000 CPU1: offline domain 0: span ffffffff groups: 00000002 00000004 00000008 00000010 00000020 00000040 00000080 00000100 00000200 00000400 00000800 00001000 00002000 00004000 00008000 00010000 00020000 00040000 00080000 00100000 00200000 00400000 00800000 01000000 02000000 04000000 08000000 10000000 20000000 40000000 80000000 00000001 CPU2: offline domain 0: span ffffffff groups: 00000004 00000008 00000010 00000020 00000040 00000080 00000100 00000200 00000400 00000800 00001000 00002000 00004000 00008000 00010000 00020000 00040000 00080000 00100000 00200000 00400000 00800000 01000000 02000000 04000000 08000000 10000000 20000000 40000000 80000000 00000001 00000002 [message CPU3 - CPU31 cut] checking if image is initramfs...it isn't (ungzip failed); looks like an initrd NET: Registered protocol family 16 EISA bus registered Searching for devices... Found devices: 1. Astro BC Runway Port at 0xfed00000 [10] { 12, 0x0, 0x582, 0x0000b } 2. Elroy PCI Bridge at 0xfed30000 [10/0] { 13, 0x0, 0x782, 0x0000a } 3. Elroy PCI Bridge at 0xfed32000 [10/1] { 13, 0x0, 0x782, 0x0000a } 4. Elroy PCI Bridge at 0xfed38000 [10/4] { 13, 0x0, 0x782, 0x0000a } 5. Elroy PCI Bridge at 0xfed3c000 [10/6] { 13, 0x0, 0x782, 0x0000a } 6. AllegroLow W at 0xfffa0000 [32] { 0, 0x0, 0x5bc, 0x00004 } 7. Memory at 0xfed10200 [49] { 1, 0x0, 0x087, 0x00009 } CPU(s): 1 x PA8500 (PCX-W) at 300.000000 MHz SBA found Astro 2.1 at 0xfed00000 lba version TR2.1 (0x2) found at 0xfed30000 WARNING: Ignoring enabled ELMMIO BASE 0xf8000000 SIZE 0xfc000000 PCI: Enabled native mode for NS87415 (pif=0x8f) lba version TR2.1 (0x2) found at 0xfed32000 WARNING: Ignoring enabled ELMMIO BASE 0xf8000000 SIZE 0xfc000000 lba version TR2.1 (0x2) found at 0xfed38000 WARNING: Ignoring enabled ELMMIO BASE 0xf8000000 SIZE 0xfc000000 lba version TR2.1 (0x2) found at 0xfed3c000 WARNING: Ignoring enabled ELMMIO BASE 0xf8000000 SIZE 0xfc000000 iosapic: hpa not registered for 0000:03:02.0 SCSI subsystem initialized TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca) STI GSC/PCI core graphics driver Version 0.9a STI PCI graphic ROM found at f7000000 (2048 kB), fb at fa000000 (32 MB) id 2fc1066b-9a02587, conforms to spec rev. 8.09 graphics card name: HPA4552A stifb: 'HPA4552A' (id: 0x2fc1066b) not supported. unwind_init: start = 0x103b5720, end = 0x103d6f20, entries = 8576 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au) devfs: boot_options: 0x0 Initializing Cryptographic API SuperIO: Found NS87560 Legacy I/O device at 0000:00:0e.1 (IRQ 64) SuperIO: Serial port 1 at 0x3f8 SuperIO: Serial port 2 at 0x2f8 SuperIO: Parallel port at 0x378 SuperIO: Floppy controller at 0x3f0 SuperIO: ACPI at 0x7e0 SuperIO: USB regulator enabled Soft power switch enabled, polling @ 0xf0400804. Generic RTC Driver v1.07 Serial: 8250/16550 driver $Revision: 1.90 $ 25 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 99) is a 16550A ttyS1 at I/O 0x2f8 (irq = 100) is a 16550A RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize sticon: Initializing STI text console. Console: switching to colour STI console 160x64 mice: PS/2 mouse device common for all mice HP SDC: No SDC found. HP SDC MLC: Registering the System Domain Controller's HIL MLC. HP SDC MLC: Request for raw HIL ISR hook denied NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 12Kbytes TCP: Hash tables configured (established 4096 bind 6553) RAMDISK: cramfs filesystem found at block 0 RAMDISK: Loading 4884 blocks [1 disk] into ram disk... done. VFS: Mounted root (cramfs filesystem) readonly. Freeing unused kernel memory: 344k freed NET: Registered protocol family 1 sym0: <896> rev 0x4 at pci 0000:00:0f.0 irq 65 sym0: No NVRAM, ID 7, Fast-40, SE, parity checking sym0: SCSI BUS has been reset. scsi0 : sym-2.1.18k Using anticipatory io scheduler sym1: <896> rev 0x4 at pci 0000:00:0f.1 irq 65 sym1: No NVRAM, ID 7, Fast-40, LVD, parity checking sym1: SCSI BUS has been reset. scsi1 : sym-2.1.18k Vendor: QUANTUM Model: ATLAS10K-9LVD Rev: HP06 Type: Direct-Access ANSI SCSI revision: 03 sym1:6:0: tagged command queuing enabled, command queue depth 16. scsi(1:0:6:0): Beginning Domain Validation sym1:6: wide asynchronous. sym1:6: FAST-40 WIDE SCSI 80.0 MB/s ST (25.0 ns, offset 31) scsi(1:0:6:0): Domain Validation skipping write tests scsi(1:0:6:0): Ending Domain Validation usbcore: registered new driver hub ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 ohci_hcd 0000:00:0e.2: National Semiconductor Corporation USB Controller ohci_hcd 0000:00:0e.2: reset, control = 0x110 ohci_hcd 0000:00:0e.2: irq 97, pci mem f4007000 ohci_hcd 0000:00:0e.2: new USB bus registered, assigned bus number 1 ohci_hcd 0000:00:0e.2: Using NSC SuperIO setup usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: default language 0x0409 usb usb1: Product: National Semiconductor Corporation USB Controller usb usb1: Manufacturer: Linux 2.6.8-2-32-smp ohci_hcd usb usb1: SerialNumber: 0000:00:0e.2 usb usb1: hotplug usb usb1: adding 1-0:1.0 (config #1, interface 0) usb 1-0:1.0: hotplug hub 1-0:1.0: usb_probe_interface hub 1-0:1.0: usb_probe_interface - got id hub 1-0:1.0: USB hub found hub 1-0:1.0: 3 ports detected hub 1-0:1.0: standalone hub hub 1-0:1.0: ganged power switching hub 1-0:1.0: no over-current protection hub 1-0:1.0: power on to power good time: 0ms hub 1-0:1.0: local power source is good hub 1-0:1.0: enabling power on all ports ohci_hcd 0000:00:0e.2: created debug files ohci_hcd 0000:00:0e.2: OHCI controller state ohci_hcd 0000:00:0e.2: OHCI 1.0, with legacy support registers ohci_hcd 0000:00:0e.2: control 0x083 HCFS=operational CBSR=3 ohci_hcd 0000:00:0e.2: cmdstatus 0x00000 SOC=0 ohci_hcd 0000:00:0e.2: intrstatus 0x00000044 RHSC SF ohci_hcd 0000:00:0e.2: intrenable 0x8000001a MIE UE RD WDH ohci_hcd 0000:00:0e.2: hcca frame #0021 ohci_hcd 0000:00:0e.2: roothub.a 00001003 POTPGT=0 NOCP NDP=3 ohci_hcd 0000:00:0e.2: roothub.b 00000000 PPCM=0000 DR=0000 ohci_hcd 0000:00:0e.2: roothub.status 00008000 DRWE ohci_hcd 0000:00:0e.2: roothub.portstatus [0] 0x00010301 CSC LSDA PPS CCS ohci_hcd 0000:00:0e.2: roothub.portstatus [1] 0x00010301 CSC LSDA PPS CCS ohci_hcd 0000:00:0e.2: roothub.portstatus [2] 0x00000100 PPS usbcore: registered new driver usbkbd drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver Linux Tulip driver version 1.1.13 (May 11, 2002) tulip0: no phy info, aborting mtable build tulip0: MII transceiver #1 config 1200 status 7809 advertising 01e1. ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00010301 CSC LSDA PPS CCS hub 1-0:1.0: port 1, status 0301, change 0001, 1.5 Mb/s eth0: Digital DS21143 Tulip rev 65 at 0xf4008000, 00:10:83:CF:A6:DC, IRQ 66. Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx hub 1-0:1.0: debounce: port 1: total 100ms stable 100ms status 0x301 ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [0] = 0x00100303 PRSC LSDA PPS PES CCS usb 1-1: new low speed USB device using address 2 usb 1-1: skipped 1 descriptor after interface usb 1-1: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-1: default language 0x0409 usb 1-1: Product: N43 usb 1-1: Manufacturer: Logitech usb 1-1: hotplug usb 1-1: adding 1-1:1.0 (config #1, interface 0) usb 1-1:1.0: hotplug usbhid 1-1:1.0: usb_probe_interface usbhid 1-1:1.0: usb_probe_interface - got id input: USB HID v1.00 Mouse [Logitech N43] on usb-0000:00:0e.2-1 ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS hub 1-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s hub 1-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301 ohci_hcd 0000:00:0e.2: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS usb 1-2: new low speed USB device using address 3 usb 1-2: skipped 1 descriptor after interface usb 1-2: skipped 1 descriptor after interface usb 1-2: new device strings: Mfr=1, Product=2, SerialNumber=0 usb 1-2: default language 0x0409 usb 1-2: Product: USB Keyboard and Mouse usb 1-2: Manufacturer: SILITEK usb 1-2: hotplug usb 1-2: adding 1-2:1.0 (config #1, interface 0) usb 1-2:1.0: hotplug usbkbd 1-2:1.0: usb_probe_interface usbkbd 1-2:1.0: usb_probe_interface - got id input: SILITEK USB Keyboard and Mouse on usb-0000:00:0e.2-2 usb 1-2: adding 1-2:1.1 (config #1, interface 1) usb 1-2:1.1: hotplug usbhid 1-2:1.1: usb_probe_interface usbhid 1-2:1.1: usb_probe_interface - got id input: USB HID v1.00 Mouse [SILITEK USB Keyboard and Mouse] on usb-0000:00:0e.2-2 NS87415: IDE controller at PCI slot 0000:00:0e.0 NS87415: chipset revision 3 NS87415: 100% native mode on irq 103 ide0: BM-DMA at 0x0a00-0x0a07, BIOS settings: hda:pio, hdb:pio ide1: BM-DMA at 0x0a08-0x0a0f, BIOS settings: hdc:pio, hdd:pio hda: CD-532E-B, ATAPI CD/DVD-ROM drive ide0 at 0xf00-0xf07,0xe02 on irq 103 hda: ATAPI 32X CD-ROM drive, 128kB Cache Uniform CD-ROM driver Revision: 3.20 SCSI device sda: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sda: drive cache: write back /dev/scsi/host1/bus0/target6/lun0: p1 p2 p3 p4 Attached scsi disk sda at scsi1, channel 0, id 6, lun 0 Adding 498004k swap on /dev/sda3. Priority:-1 extents:1 ad1889: ad1889 at 0xf400c000 IRQ 67 ac97_codec: AC97 Audio codec, id: ADS3 (Analog Devices AD1819) ehci_hcd: block sizes: qh 128 qtd 96 itd 192 sitd 96 USB Universal Host Controller Interface driver v2.2 ts: Compaq touchscreen protocol output NET: Registered protocol family 17 module ipv6 relocation of symbol capable is out of range (0x3ffeffdc in 17 bits) eth0: Setting full-duplex based on MII#1 link partner capability of 45e1. -- GMX DSL-Flatrate 1 Jahr kostenlos* + WLAN-Router ab 0,- Euro* Bis 31.12.2005 einsteigen! Infos unter: http://www.gmx.net/de/go/dsl _______________________________________________ parisc-linux mailing list parisc-linux@lists.parisc-linux.org http://lists.parisc-linux.org/mailman/listinfo/parisc-linux