Re: [parisc-linux] Bug report

[Richard Hirst <rhirst@linuxcare.com>]

My 715/75 hangs there if CONFIG_PARPORT_GSC is enabled.  Don't know if that
was turned on on the CD kernel, but it probably was (defaults to on).

Richard


On Fri, Sep 08, 2000 at 06:54:38PM +0000, Robert Stickel wrote:
> 
> Hello,
> 
> The good news: We are really excited about the Puffin project.
> 
> The bad news: We tried to boot an Apollo 9000/710 on your PA/Linux
> Developer's
> Release CD, Version 0.1 - Snapshot 2000/08/04 and never quite got to a
> root
> prompt (see transcript below).  Should this be possible or are we
> missing
> something?
> 
> Thanks for any advice,
> 
> rstickel@mindspring.com
> sts@minitower.gtri.gatech.edu
> 
> 
> 
> 
> Transcript of attempt to boot Apollo 9000/710 on Puffin CD.  At the
> request_irq(259, c01ec76c, 0x0, asp, c3fcd080)
> line the systems hangs.
> 
> 
> 
> (c) Copyright.  Hewlett-Packard Company.  1991.
> All rights reserved.
> 
> PDC ROM rev. 2.0
> IODC ROM rev. 2.0
> 64 MB of memory configured and tested.
> 
> 
> Selecting a system to boot.
> To stop selection process, press and hold the ESCAPE key.
> 
> Selection process stopped.
> 
> Searching for Potential Boot Devices.
> To terminate search, press and hold the ESCAPE key.
> 
> Device Selection      Device Path              Device Type
> ----------------------------------------------------------------------------
> 
> P0                    scsi.6.0                 MATSHITACD-ROM CR-8005A
> P1                    scsi.5.0                 IOMEGA  ZIP 100
> P2                    scsi.4.0                 iomega  jaz 1GB
> P3                    scsi.3.0                 SEAGATE ST11200N SUN1.05
> P4                    scsi.2.0                 SEAGATE ST31230N
> P5                    scsi.1.0                 IBM     0662
> 
> 
> 
> b)    Boot from specified device
> s)    Search for bootable devices
> a)    Enter Boot Administration mode
> x)    Exit and continue boot sequence
> ?)    Help
> 
> Select from menu: a
> BOOT_ADMIN> info
> ----------------------------- Hardware Configuration
> ------------------------
> 
> Machine model: 9000/710
> 
> Processor Frequency        = 50000000 Hz
> I/O Subsystem Frequency    = 25000000 Hz
> 
> LAN Jumper Status: Internal ThinLAN Port selected
> 
> Processor Revision                  = 3
> System Controller Revision          = 0
> Floating Point Coprocessor Revision = 3
> 
> Hardware Version            12288     (0x00003000)
> Software Version             1153     (0x00000481)
> 
> BOOT_ADMIN> boot alt
> 
> Trying scsi.6.0
> Boot path initialized.
> Attempting to load IPL.
> 
> 
> Hard booted.
> palo ipl bame@noam Fri Aug  4 18:36:35 MDT 2000
> 0/vmlinux 2349352 bytes @ 0x6e8800
> 0/palo-cmdline '0/vmlinux TERM=linux HOME=/ root=/dev/scd0'
> Kernel: partition 0 file /vmlinux
> ELF32 executable
> 
> Entry 00100000 first 00100000 n 4
> Segment 0 load 00100000 size 1511580 mediaptr 0x1000
> Segment 1 load 00272000 size 132368 mediaptr 0x173000
> Segment 2 load 00294000 size 86880 mediaptr 0x194000
> Segment 3 load 002ac000 size 8192 mediaptr 0x1aa000
> branching to kernel entry point 0x00100000
> pdc_cons registered !
> The Kernel has started...
> Free memory starts at: 0xc02dc000
> PALO command line: 'TERM=linux HOME=/ root=/dev/scd0'
> PALO initrd 0-0
> FP CCR was 0x0, will be set to 0xc0
> model   00003000 00000481 00000000 00000000 78243572 00000000 00000004
> 0000000d 00000000
> vers    00000003
> CPUID vers 0 rev 0
> CPU(s): 1 x PA7000 at 50.000000 MHz
> Searching for devices in PDC firmware...  an older box...
> Found devices:
> 1. Stinger Optional Graphics (10) at 0xf4000000, versions 0x6, 0x0,
> 0x77, 0x0, 0x0
> 2. Bushmaster Core BA (11) at 0xf082f000, versions 0x6, 0x0, 0x70, 0x0,
> 0x0
> 3. Bushmaster Core SCSI (10) at 0xf0825000, versions 0x6, 0x0, 0x71,
> 0x0, 0x0
> 4. Bushmaster Core LAN (802.3) (10) at 0xf0826000, versions 0x6, 0x0,
> 0x72, 0x0, 0x0
> 5. Bushmaster Core HIL (10) at 0xf0821000, versions 0x6, 0x0, 0x73, 0x0,
> 0x0
> 6. Bushmaster Core RS-232 (10) at 0xf0823000, versions 0x6, 0x0, 0x75,
> 0x0, 0x0
> 7. Bushmaster Core RS-232 (10) at 0xf0822000, versions 0x6, 0x0, 0x75,
> 0x0, 0x0
> 8. Bushmaster Core Centronics (10) at 0xf0824000, versions 0x6, 0x0,
> 0x74, 0x0, 0x0
> 9. Bushmaster Audio (10) at 0xf1000000, versions 0x6, 0x0, 0x7a, 0x0,
> 0x0
> 10. Bushmaster (710) (0) at 0xfffbe000, versions 0x300, 0x0, 0x4, 0x0,
> 0x81
> 11. Bushmaster (1) at 0xfffbf000, versions 0x16, 0x0, 0x9, 0x0, 0x0
> That's a total of 11 devices.
> Linux version 2.3.99-pre8 (bame@noam) (gcc version 2.96 20000707
> (experimental)) #24 Fri Aug 4 18:27:58 MDT 2000
> initrd: 00000000-00000000
> pagetable_init
> On node 0 totalpages: 16384
> zone(0): 8192 pages.
> zone(1): 8192 pages.
> zone(2): 0 pages.
> trap_init
> Calibrating delay loop... 46.08 BogoMIPS
> Memory: 61380k available
> Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
> Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
> Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
> kmem_create: Poisoning requested, but con given - bdev_cache
> Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
> kmem_create: Poisoning requested, but con given - inode_cache
> POSIX conformance testing by UNIFIX
> ASP version 1 at 0xf0800000 found.
> request_irq(259, c01ec76c, 0x0, asp, c3fcd080)
> 
> ---------------------------------------------------------------------------
> To unsubscribe: send e-mail to parisc-linux-request@thepuffingroup.com with
> `unsubscribe' as the subject.
> 
>