From mboxrd@z Thu Jan 1 00:00:00 1970 Received: from cosrel2.hp.com (cosrel2.hp.com [156.153.255.162]) by puffin.external.hp.com (8.9.3/8.9.3) with ESMTP id XAA29982 for ; Wed, 6 Dec 2000 23:32:59 -0700 Received: from milano.cup.hp.com (milano.cup.hp.com [15.8.80.76]) by cosrel2.hp.com (Postfix) with ESMTP id D4441663 for ; Wed, 6 Dec 2000 23:35:36 -0700 (MST) Date: Wed, 6 Dec 2000 22:34:55 -0800 (PST) From: Grant Grundler Message-Id: <200012070634.WAA07459@milano.cup.hp.com> To: parisc-linux@puffin.external.hp.com Cc: debian-hppa@lists.debian.org Mime-Version: 1.0 Content-Type: text/plain; charset=us-ascii Subject: [parisc-linux] A500 status update List-ID: Good News! *** A500 is starting to come alive! *** Kudos to (in alpha order): amodra, danglin dhd, ggg (myself), jsm, pb, rhirst and others names I just can't think of right now. Kudos for long hours on the 64-bit specific issues: Toolchain, VM, Boot loader, PDC wrappers, PAT PDC inventory, 32->64-bit syscall translators, device drivers, kernel module support, etc....Output log is below. TODO: o sym53c896 driver is quite verbose at boot...do we still need this? o kernel message buffer gets dumped again when "Switching from PDC console" o mke2fs will sometimes crash the system. Typical symptom of I/O MMU support (SBA driver) not handling Scatter-Gather mappings correctly. That's my problem. However I was not able to reproduce it yet. o dd to raw disk isn't working right. "No space left on device". See the output below. o don't see Acenic driver output. I've got CONFIG_ACENIC=y and the device is definitely seen by PCI. good night! grant Firmware Version 40.32 Duplex Console IO Dependent Code (IODC) revision 1 ------------------------------------------------------------------------------ (c) Copyright 1995-1998, Hewlett-Packard Company, All rights reserved ------------------------------------------------------------------------------ Processor Speed State CoProcessor State Cache Size Number State Inst Data --------- -------- --------------------- ----------------- ------------ 0 440 MHz Active Functional 512 KB 1 MB 1 440 MHz Idle Functional 512 KB 1 MB Central Bus Speed (in MHz) : 111 Available Memory : 262144 KB Good Memory Required : 11468 KB Primary boot path: 0/0/1/1.15 Alternate boot path: 0/0/2/1.15 Console path: 0/0/4/0.0 Keyboard path: 0/0/4/0.0 WARNING: The non-destructive test bit was set, so memory was not tested destructively. Information only, no action required. ---- Main Menu --------------------------------------------------------------- Command Description ------- ----------- BOot [PRI|ALT|] Boot from specified path PAth [PRI|ALT] [] Display or modify a path SEArch [DIsplay|IPL] [] Search for boot devices COnfiguration menu Displays or sets boot values INformation menu Displays hardware information SERvice menu Displays service commands DIsplay Redisplay the current menu HElp [|] Display help for menu or command RESET Restart the system ---- Main Menu: Enter command or menu > in io I/O MODULE INFORMATION Path Slot IODC Type (dec) Number HVERSION SVERSION Vers ---- ----- ------ -------- -------- ---- System bus adapter 0 0x5820 0xb10 0x0 Local bus adapter 0/0 4 0x7820 0xa00 0x0 Local bus adapter 0/2 1 0x7820 0xa00 0x0 Local bus adapter 0/4 2 0x7820 0xa00 0x0 Local bus adapter 0/6 3 0x7820 0xa00 0x0 PCI DEVICE INFORMATION Path Vendor Device Bus Slot Description (dec) Id Id # # ----------- ----- ---- ---- --- --- Ethernet cntlr 0/0/0/0 0x1011 0x19 0 Built_In SCSI bus cntlr 0/0/1/0 0x1000 0xb 0 Built_In SCSI bus cntlr 0/0/1/1 0x1000 0xb 0 Built_In SCSI bus cntlr 0/0/2/0 0x1000 0xf 0 Built_In SCSI bus cntlr 0/0/2/1 0x1000 0xf 0 Built_In Comp. ser cntlr 0/0/4/0 0x103c 0x1048 0 Built_In Comp. ser cntlr 0/0/5/0 0x103c 0x1048 0 Built_In Ethernet cntlr 0/2/0/0 0x12ae 0x1 16 1 SCSI bus cntlr 0/4/0/0 0x1000 0xb 32 2 SCSI bus cntlr 0/4/0/1 0x1000 0xb 32 2 PCI-to-PCI bridge 0/6/0/0 0x1011 0x26 48 4 SCSI bus cntlr 0/6/0/0/4/0 0x1000 0xb 49 4 SCSI bus cntlr 0/6/0/0/4/1 0x1000 0xb 49 4 Ethernet cntlr 0/6/0/0/6/0 0x1011 0x19 49 4 Ethernet cntlr 0/6/0/0/7/0 0x1011 0x19 49 4 PCI-to-PCI bridge 0/6/0/0 0x1011 0x26 48 4 PCI-to-PCI bridge 0/6/2/0 0x1011 0x24 48 3 Ethernet cntlr 0/6/2/0/4/0 0x1011 0x9 50 3 Ethernet cntlr 0/6/2/0/5/0 0x1011 0x9 50 3 Ethernet cntlr 0/6/2/0/6/0 0x1011 0x9 50 3 Ethernet cntlr 0/6/2/0/7/0 0x1011 0x9 50 3 PCI-to-PCI bridge 0/6/2/0 0x1011 0x24 48 3 Main Menu: Enter command or menu > bo lan Interact with IPL (Y, N, or Cancel)?> n Booting... Network Station Address 00306e-03799f System IP Address 15.8.80.78 Server IP Address 15.8.81.247 Boot IO Dependent Code (IODC) revision 2 HARD Booted. palo ipl grundler@hpisp747 Wed Nov 8 21:40:37 PST 2000 0/vmlinux 3170434 bytes @ 0x6800 0/palo-cmdline '0/vmlinux HOME=/ TERM=LINUX root=/dev/nfs nfsroot=15.8.81.247:/tftpboot/hppa ' Kernel: partition 0 file /vmlinux ELF64 executable Entry 00100000 first 00100000 n 3 Segment 0 load 00100000 size 1804864 mediaptr 0x1000 Segment 1 load 002ba000 size 428968 mediaptr 0x1ba000 Segment 2 load 00324000 size 376832 mediaptr 0x223000 branching to kernel entry point 0x00100000 Set default PSW W bit to 1 PDC Console Initialized The 64-bit Kernel has started... Enabled FP coprocessor If this is the LAST MESSAGE YOU SEE, you're probably using 32-bit millicode by mistake. Free memory starts at: 0xc03c3000 start_parisc(0x504ce8,0x504ce8,0x0,0x0) PALO command line: 'HOME=/ TERM=LINUX root=/dev/nfs nfsroot=15.8.81.247:/tftpboot/hppa ' PALO initrd 0-0 model 00005cb0 00000491 00000000 00000001 23355fdc 100000f0 00000008 000000b2 000000b2 vers 00000300 cpuid 0000022a CPUID vers 17 rev 10 model 9000/800/A500-44 Searching for devices in PDC firmware... processor hpa 0xfffffffffffa0000 Found devices: 1. Crescendo 440 (0) at 0xfffffffffffa0000, versions 0x5cb, 0x0, 0x4, 0x0, 0x91 2. Crescendo 440 (0) at 0xfffffffffffa2000, versions 0x5cb, 0x0, 0x4, 0x0, 0x91 3. Crescendo Memory (1) at 0xfffffffffed08000, versions 0x9b, 0x0, 0x9, 0x0, 0x0 4. Astro BC Runway Port (12) at 0xfffffffffed00000, versions 0x582, 0x0, 0xb, 0x0, 0x10 5. Elroy PCI Bridge (13) at 0xfffffffffed30000, versions 0x782, 0x0, 0xa, 0x0, 0x0 6. Elroy PCI Bridge (13) at 0xfffffffffed34000, versions 0x782, 0x0, 0xa, 0x0, 0x0 7. Elroy PCI Bridge (13) at 0xfffffffffed38000, versions 0x782, 0x0, 0xa, 0x0, 0x0 8. Elroy PCI Bridge (13) at 0xfffffffffed3c000, versions 0x782, 0x0, 0xa, 0x0, 0x0 That's a total of 8 devices. CONFIG_SMP disabled - not claiming addional CPUs Warning : device (0, 0x5cb, 0x0, 0x4, 0x0) NOT claimed by CPU PARISC CPU(s): 1 x PA8500 (PCX-W) at 440.000000 MHz Linux version 2.4.0-test10 (grundler@hpisp747) (gcc version 2.96 20000925 (experimental)) #6 Wed Dec 6 17:14:11 PST 2000 free_bootmem(0x3c5000, 0xfc3b000) initrd: 00000000-00000000 pagetable_init On node 0 totalpages: 65536 zone(0): 32768 pages. zone(1): 32768 pages. zone(2): 0 pages. Kernel command line: HOME=/ TERM=LINUX root=/dev/nfs nfsroot=15.8.81.247:/tftpboot/hppa trap_init Calibrating delay loop... 878.18 BogoMIPS Memory: 249052k available Dentry-cache hash table entries: 32768 (order: 7, 524288 bytes) Buffer-cache hash table entries: 16384 (order: 5, 131072 bytes) Page-cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 16384 (order: 6, 262144 bytes) POSIX conformance testing by UNIFIX lba version TR4.0 (0x5) found at 0xfffffffffed30000 lba range[2] : ignoring GMMIO (0xfffffff804000000) PCI Found 00:00 [1011/0019] 000200 00 PCI Found 00:08 [1000/000b] 000100 00 PCI Found 00:09 [1000/000b] 000100 00 PCI Found 00:10 [1000/000f] 000100 00 PCI Found 00:11 [1000/000f] 000100 00 PCI Found 00:20 [103c/1048] 000700 00 PCI Found 00:28 [103c/1048] 000700 00 PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit lba version TR4.0 (0x5) found at 0xfffffffffed34000 lba range[2] : ignoring GMMIO (0xfffffff904000000) PCI Found 10:00 [12ae/0001] 000200 00 lba version TR4.0 (0x5) found at 0xfffffffffed38000 lba range[2] : ignoring GMMIO (0xfffffffa04000000) PCI Found 20:00 [1000/000b] 000100 00 PCI Found 20:01 [1000/000b] 000100 00 PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit lba version TR4.0 (0x5) found at 0xfffffffffed3c000 lba range[2] : ignoring GMMIO (0xfffffffb04000000) PCI Found 30:00 [1011/0026] 000604 01 PCI Found 30:10 [1011/0024] 000604 01 PCI Found 31:20 [1000/000b] 000100 00 PCI Found 31:21 [1000/000b] 000100 00 PCI Found 31:30 [1011/0019] 000200 00 PCI Found 31:38 [1011/0019] 000200 00 PCI : ignoring 30:00.0 PCI-PCI bridge - I/O BASE not configured PCI Found 32:20 [1011/0009] 000200 00 PCI Found 32:28 [1011/0009] 000200 00 PCI Found 32:30 [1011/0009] 000200 00 PCI Found 32:38 [1011/0009] 000200 00 PCI : ignoring 30:02.0 PCI-PCI bridge - I/O BASE not configured PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit PCI: dev PCI device 1000:000b type 64-bit SBA found Astro 2.1 at 0xfffffffffed00000 Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Starting kswapd v1.8 pty: 256 Unix98 ptys configured request_module[parport_lowlevel]: Root fs not mounted lp: driver loaded but no devices found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Serial driver version 5.02 (2000-08-09) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at port 0x0080 (irq = 132) is a 16550A PCIBIOS: Enabling device 00:05.0 (0007 -> 0147) ttyS01 at port 0x00c0 (irq = 133) is a 16550A Linux Tulip driver version 0.9.10 (September 6, 2000) PCIBIOS: Setting latency timer of 00:00.0 to 128 eth0: Digital DS21143 Tulip rev 65 at 0x0, 00:30:6E:03:79:9F, IRQ 128. eth0: MII transceiver #1 config 1000 status 782d advertising 01e1. PCIBIOS: Enabling device 31:06.0 (0007 -> 0147) PCIBIOS: Setting latency timer of 31:06.0 to 128 eth1: Digital DS21143 Tulip rev 65 at 0x30200, 00:10:83:7B:0A:3E, IRQ 322. eth1: EEPROM default media type Autosense. eth1: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block. eth1: MII transceiver #0 config 1000 status 7809 advertising 01e1. PCIBIOS: Enabling device 31:07.0 (0007 -> 0147) PCIBIOS: Setting latency timer of 31:07.0 to 128 eth2: Digital DS21143 Tulip rev 65 at 0x30280, 00:10:83:7B:0A:3F, IRQ 323. eth2: EEPROM default media type Autosense. eth2: Index #0 - Media MII (#11) described by a 21142 MII PHY (3) block. eth2: MII transceiver #0 config 1000 status 7809 advertising 01e1. PCIBIOS: Enabling device 32:04.0 (0007 -> 0147) PCIBIOS: Setting latency timer of 32:04.0 to 128 eth3: Digital DS21140 Tulip rev 34 at 0x31000, 00:00:D1:1A:31:BF, IRQ 322. eth3: EEPROM default media type Autosense. eth3: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. eth3: MII transceiver #1 config 3100 status 7849 advertising 0101. eth3: Advertising 01e1 on PHY 1, previously advertising 0101. eth3: Advertising 01e1 (to advertise is 01e1). PCIBIOS: Enabling device 32:05.0 (0007 -> 0147) PCIBIOS: Setting latency timer of 32:05.0 to 128 eth4: Digital DS21140 Tulip rev 34 at 0x31080, 00:00:D1:1A:32:22, IRQ 323. eth4: EEPROM default media type Autosense. eth4: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. eth4: MII transceiver #1 config 3100 status 7849 advertising 0101. eth4: Advertising 01e1 on PHY 1, previously advertising 0101. eth4: Advertising 01e1 (to advertise is 01e1). PCIBIOS: Enabling device 32:06.0 (0007 -> 0147) PCIBIOS: Setting latency timer of 32:06.0 to 128 eth5: Digital DS21140 Tulip rev 34 at 0x31100, 00:00:D1:1A:31:B9, IRQ 324. eth5: EEPROM default media type Autosense. eth5: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. eth5: MII transceiver #1 config 3100 status 7849 advertising 0101. eth5: Advertising 01e1 on PHY 1, previously advertising 0101. eth5: Advertising 01e1 (to advertise is 01e1). PCIBIOS: Enabling device 32:07.0 (0007 -> 0147) PCIBIOS: Setting latency timer of 32:07.0 to 128 eth6: Digital DS21140 Tulip rev 34 at 0x31180, 00:00:D1:1A:31:C4, IRQ 325. eth6: EEPROM default media type Autosense. eth6: Index #0 - Media MII (#11) described by a 21140 MII PHY (1) block. eth6: MII transceiver #1 config 3100 status 7849 advertising 0101. eth6: Advertising 01e1 on PHY 1, previously advertising 0101. eth6: Advertising 01e1 (to advertise is 01e1). SCSI subsystem driver Revision: 1.00 sym53c8xx: at PCI bus 0, device 2, function 0 sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) sym53c8xx: changing PCI_LATENCY_TIMER from 0 to 80. sym53c8xx: 53c876 detected sym53c8xx: at PCI bus 0, device 2, function 1 sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) sym53c8xx: changing PCI_LATENCY_TIMER from 0 to 80. sym53c8xx: 53c876 detected sym53c8xx: at PCI bus 0, device 1, function 0 sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) sym53c8xx: changing PCI_LATENCY_TIMER from 0 to 80. sym53c8xx: 53c896 detected sym53c8xx: at PCI bus 0, device 1, function 1 sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) sym53c8xx: changing PCI_LATENCY_TIMER from 0 to 80. sym53c8xx: 53c896 detected sym53c8xx: at PCI bus 32, device 0, function 0 sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) sym53c8xx: changing PCI_LATENCY_TIMER from 0 to 80. sym53c8xx: 53c896 detected sym53c8xx: at PCI bus 32, device 0, function 1 sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) sym53c8xx: changing PCI_LATENCY_TIMER from 0 to 80. sym53c8xx: 53c896 detected sym53c8xx: at PCI bus 49, device 4, function 0 sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) sym53c8xx: changing PCI_LATENCY_TIMER from 0 to 80. sym53c8xx: 53c896 detected sym53c8xx: at PCI bus 49, device 4, function 1 sym53c8xx: setting PCI_COMMAND_PARITY...(fix-up) sym53c8xx: changing PCI_LATENCY_TIMER from 0 to 80. sym53c8xx: 53c896 detected sym53c876-0: rev 0x14 on pci bus 0 device 2 function 0 irq 130 sym53c876-0: NCR clock is 40218KHz sym53c876-0: ID 7, Fast-20, Parity Checking sym53c876-0: on-chip RAM at 0xfffffffff8008000 sym53c876-0: restart (scsi reset). sym53c876-0: Downloading SCSI SCRIPTS. sym53c876-1: rev 0x14 on pci bus 0 device 2 function 1 irq 131 sym53c876-1: NCR clock is 40218KHz sym53c876-1: ID 7, Fast-20, Parity Checking sym53c876-1: on-chip RAM at 0xfffffffff800a000 sym53c876-1: restart (scsi reset). sym53c876-1: Downloading SCSI SCRIPTS. sym53c896-2: rev 0x7 on pci bus 0 device 1 function 0 irq 129 sym53c896-2: NCR clock is 40218KHz sym53c896-2: ID 7, Fast-40, Parity Checking sym53c896-2: on-chip RAM at 0xfffffffff8002000 sym53c896-2: restart (scsi reset). sym53c896-2: handling phase mismatch from SCRIPTS. sym53c896-2: Downloading SCSI SCRIPTS. sym53c896-3: rev 0x7 on pci bus 0 device 1 function 1 irq 130 sym53c896-3: NCR clock is 40218KHz sym53c896-3: ID 7, Fast-40, Parity Checking sym53c896-3: on-chip RAM at 0xfffffffff8006000 sym53c896-3: restart (scsi reset). sym53c896-3: handling phase mismatch from SCRIPTS. sym53c896-3: Downloading SCSI SCRIPTS. sym53c896-4: rev 0x1 on pci bus 32 device 0 function 0 irq 256 sym53c896-4: NCR clock is 40218KHz sym53c896-4: ID 7, Fast-40, Parity Checking sym53c896-4: on-chip RAM at 0xfffffffffa002000 sym53c896-4: restart (scsi reset). sym53c896-4: handling phase mismatch from SCRIPTS. sym53c896-4: Downloading SCSI SCRIPTS. sym53c896-5: rev 0x1 on pci bus 32 device 0 function 1 irq 257 sym53c896-5: NCR clock is 40218KHz sym53c896-5: ID 7, Fast-40, Parity Checking sym53c896-5: on-chip RAM at 0xfffffffffa004000 sym53c896-5: restart (scsi reset). sym53c896-5: handling phase mismatch from SCRIPTS. sym53c896-5: Downloading SCSI SCRIPTS. sym53c896-6: rev 0x5 on pci bus 49 device 4 function 0 irq 320 sym53c896-6: NCR clock is 40218KHz sym53c896-6: ID 7, Fast-40, Parity Checking sym53c896-6: on-chip RAM at 0xfffffffffb002000 sym53c896-6: restart (scsi reset). sym53c896-6: handling phase mismatch from SCRIPTS. sym53c896-6: Downloading SCSI SCRIPTS. sym53c896-7: rev 0x5 on pci bus 49 device 4 function 1 irq 321 sym53c896-7: NCR clock is 40218KHz sym53c896-7: ID 7, Fast-40, Parity Checking sym53c896-7: on-chip RAM at 0xfffffffffb004000 sym53c896-7: restart (scsi reset). sym53c896-7: handling phase mismatch from SCRIPTS. sym53c896-7: Downloading SCSI SCRIPTS. scsi0 : sym53c8xx - version 1.6b scsi1 : sym53c8xx - version 1.6b scsi2 : sym53c8xx - version 1.6b scsi3 : sym53c8xx - version 1.6b scsi4 : sym53c8xx - version 1.6b scsi5 : sym53c8xx - version 1.6b scsi6 : sym53c8xx - version 1.6b scsi7 : sym53c8xx - version 1.6b Vendor: SEAGATE Model: ST39102LC Rev: 7C03 Type: Direct-Access ANSI SCSI revision: 02 sym53c876-1-<15,0>: tagged command queue depth set to 8 Vendor: HP Model: D5989B Rev: 1.02 Type: Processor ANSI SCSI revision: 02 sym53c896-2-<13,0>: wide msgin: 1-2-3-1. sym53c896-2-<13,0>: wide: wide=1 chg=0. sym53c896-2-<13,0>: wide msgout: 1-2-3-1. sym53c896-2-<13,0>: sync msg in: 1-3-1-a-f. sym53c896-2-<13,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=15 fak=0 chg=1. sym53c896-2-<13,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 15) sym53c896-2-<13,0>: sync msgout: 1-3-1-c-f. Vendor: HP Model: 9.10GB B 80-1205 Rev: Type: Direct-Access ANSI SCSI revision: 02 sym53c896-2-<14,0>: wide msgin: 1-2-3-1. sym53c896-2-<14,0>: wide: wide=1 chg=0. sym53c896-2-<14,0>: wide msgout: 1-2-3-1. sym53c896-2-<14,0>: sync msg in: 1-3-1-a-f. sym53c896-2-<14,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=15 fak=0 chg=1. sym53c896-2-<14,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 15) sym53c896-2-<14,0>: sync msgout: 1-3-1-c-f. Vendor: HP Model: 9.10GB B 80-1205 Rev: Type: Direct-Access ANSI SCSI revision: 02 sym53c896-2-<15,0>: wide msgin: 1-2-3-1. sym53c896-2-<15,0>: wide: wide=1 chg=0. sym53c896-2-<15,0>: wide msgout: 1-2-3-1. sym53c896-2-<15,0>: sync msg in: 1-3-1-a-f. sym53c896-2-<15,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=15 fak=0 chg=1. sym53c896-2-<15,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 15) sym53c896-2-<15,0>: sync msgout: 1-3-1-c-f. Vendor: HP Model: 9.10GB B 80-1205 Rev: Type: Direct-Access ANSI SCSI revision: 02 sym53c896-2-<13,0>: tagged command queue depth set to 8 sym53c896-2-<14,0>: tagged command queue depth set to 8 sym53c896-2-<15,0>: tagged command queue depth set to 8 Vendor: SEAGATE Model: ST318404LC Rev: HP01 Type: Direct-Access ANSI SCSI revision: 03 sym53c896-3-<15,0>: tagged command queue depth set to 8 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: HP Model: A5272A Rev: HP04 Type: Enclosure ANSI SCSI revision: 02 sym53c896-4-<0,0>: tagged command queue depth set to 8 sym53c896-4-<2,0>: tagged command queue depth set to 8 sym53c896-4-<3,0>: tagged command queue depth set to 8 sym53c896-4-<13,0>: tagged command queue depth set to 8 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Vendor: HP Model: A5272A Rev: HP04 Type: Enclosure ANSI SCSI revision: 02 sym53c896-6-<0,0>: tagged command queue depth set to 8 sym53c896-6-<1,0>: tagged command queue depth set to 8 sym53c896-6-<2,0>: tagged command queue depth set to 8 sym53c896-6-<3,0>: tagged command queue depth set to 8 sym53c896-6-<13,0>: tagged command queue depth set to 8 Detected scsi disk sda at scsi1, channel 0, id 15, lun 0 Detected scsi disk sdb at scsi2, channel 0, id 13, lun 0 Detected scsi disk sdc at scsi2, channel 0, id 14, lun 0 Detected scsi disk sdd at scsi2, channel 0, id 15, lun 0 Detected scsi disk sde at scsi3, channel 0, id 15, lun 0 Detected scsi disk sdf at scsi4, channel 0, id 0, lun 0 Detected scsi disk sdg at scsi4, channel 0, id 2, lun 0 Detected scsi disk sdh at scsi4, channel 0, id 3, lun 0 Detected scsi disk sdi at scsi4, channel 0, id 13, lun 0 Detected scsi disk sdj at scsi6, channel 0, id 0, lun 0 Detected scsi disk sdk at scsi6, channel 0, id 1, lun 0 Detected scsi disk sdl at scsi6, channel 0, id 2, lun 0 Detected scsi disk sdm at scsi6, channel 0, id 3, lun 0 Detected scsi disk sdn at scsi6, channel 0, id 13, lun 0 sym53c876-1-<15,0>: wide msgout: 1-2-3-1. sym53c876-1-<15,0>: wide msgin: 1-2-3-1. sym53c876-1-<15,0>: wide: wide=1 chg=0. sym53c876-1-<15,0>: wide msgout: 1-2-3-1. sym53c876-1-<15,0>: wide msgin: 1-2-3-1. sym53c876-1-<15,0>: wide: wide=1 chg=0. sym53c876-1-<15,0>: sync msgout: 1-3-1-c-10. sym53c876-1-<15,0>: sync msg in: 1-3-1-c-f. sym53c876-1-<15,0>: sync: per=12 scntl3=0x90 scntl4=0x0 ofs=15 fak=0 chg=0. sym53c876-1-<15,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 15) SCSI device sda: 17781521 512-byte hdwr sectors (9104 MB) Partition check: sda: sda1 sda2 sda3 sda4 sym53c896-2-<13,0>: wide msgout: 1-2-3-1. sym53c896-2-<13,0>: wide msgin: 1-2-3-1. sym53c896-2-<13,0>: wide: wide=1 chg=0. sym53c896-2-<13,0>: sync msgout: 1-3-1-c-1f. sym53c896-2-<13,0>: sync msg in: 1-3-1-c-f. sym53c896-2-<13,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=15 fak=0 chg=0. sym53c896-2-<13,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 15) SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB) sdb: sym53c896-2-<14,0>: wide msgout: 1-2-3-1. sym53c896-2-<14,0>: wide msgin: 1-2-3-1. sym53c896-2-<14,0>: wide: wide=1 chg=0. sym53c896-2-<14,0>: sync msgout: 1-3-1-c-1f. sym53c896-2-<14,0>: sync msg in: 1-3-1-c-f. sym53c896-2-<14,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=15 fak=0 chg=0. sym53c896-2-<14,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 15) SCSI device sdc: 17773524 512-byte hdwr sectors (9100 MB) sdc: sym53c896-2-<15,0>: wide msgout: 1-2-3-1. sym53c896-2-<15,0>: wide msgin: 1-2-3-1. sym53c896-2-<15,0>: wide: wide=1 chg=0. sym53c896-2-<15,0>: sync msgout: 1-3-1-c-1f. sym53c896-2-<15,0>: sync msg in: 1-3-1-c-f. sym53c896-2-<15,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=15 fak=0 chg=0. sym53c896-2-<15,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 15) SCSI device sdd: 17773524 512-byte hdwr sectors (9100 MB) sdd: sym53c896-3-<15,0>: wide msgout: 1-2-3-1. sym53c896-3-<15,0>: wide msgin: 1-2-3-1. sym53c896-3-<15,0>: wide: wide=1 chg=0. sym53c896-3-<15,0>: wide msgout: 1-2-3-1. sym53c896-3-<15,0>: wide msgin: 1-2-3-1. sym53c896-3-<15,0>: wide: wide=1 chg=0. sym53c896-3-<15,0>: sync msgout: 1-3-1-c-1f. sym53c896-3-<15,0>: sync msg in: 1-3-1-c-1f. sym53c896-3-<15,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-3-<15,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sde: 35566480 512-byte hdwr sectors (18210 MB) sde: unknown partition table sym53c896-4-<0,0>: wide msgout: 1-2-3-1. sym53c896-4-<0,0>: wide msgin: 1-2-3-1. sym53c896-4-<0,0>: wide: wide=1 chg=0. sym53c896-4-<0,0>: wide msgout: 1-2-3-1. sym53c896-4-<0,0>: wide msgin: 1-2-3-1. sym53c896-4-<0,0>: wide: wide=1 chg=0. sym53c896-4-<0,0>: sync msgout: 1-3-1-c-1f. sym53c896-4-<0,0>: sync msg in: 1-3-1-c-1f. sym53c896-4-<0,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-4-<0,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdf: 35566480 512-byte hdwr sectors (18210 MB) sdf: unknown partition table sym53c896-4-<2,0>: wide msgout: 1-2-3-1. sym53c896-4-<2,0>: wide msgin: 1-2-3-1. sym53c896-4-<2,0>: wide: wide=1 chg=0. sym53c896-4-<2,0>: wide msgout: 1-2-3-1. sym53c896-4-<2,0>: wide msgin: 1-2-3-1. sym53c896-4-<2,0>: wide: wide=1 chg=0. sym53c896-4-<2,0>: sync msgout: 1-3-1-c-1f. sym53c896-4-<2,0>: sync msg in: 1-3-1-c-1f. sym53c896-4-<2,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-4-<2,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdg: 35566480 512-byte hdwr sectors (18210 MB) sdg: unknown partition table sym53c896-4-<3,0>: wide msgout: 1-2-3-1. sym53c896-4-<3,0>: wide msgin: 1-2-3-1. sym53c896-4-<3,0>: wide: wide=1 chg=0. sym53c896-4-<3,0>: wide msgout: 1-2-3-1. sym53c896-4-<3,0>: wide msgin: 1-2-3-1. sym53c896-4-<3,0>: wide: wide=1 chg=0. sym53c896-4-<3,0>: sync msgout: 1-3-1-c-1f. sym53c896-4-<3,0>: sync msg in: 1-3-1-c-1f. sym53c896-4-<3,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-4-<3,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdh: 35566480 512-byte hdwr sectors (18210 MB) sdh: unknown partition table sym53c896-4-<13,0>: wide msgout: 1-2-3-1. sym53c896-4-<13,0>: wide msgin: 1-2-3-1. sym53c896-4-<13,0>: wide: wide=1 chg=0. sym53c896-4-<13,0>: wide msgout: 1-2-3-1. sym53c896-4-<13,0>: wide msgin: 1-2-3-1. sym53c896-4-<13,0>: wide: wide=1 chg=0. sym53c896-4-<13,0>: sync msgout: 1-3-1-c-1f. sym53c896-4-<13,0>: sync msg in: 1-3-1-c-1f. sym53c896-4-<13,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-4-<13,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdi: 35566480 512-byte hdwr sectors (18210 MB) sdi: unknown partition table sym53c896-6-<0,0>: wide msgout: 1-2-3-1. sym53c896-6-<0,0>: wide msgin: 1-2-3-1. sym53c896-6-<0,0>: wide: wide=1 chg=0. sym53c896-6-<0,0>: wide msgout: 1-2-3-1. sym53c896-6-<0,0>: wide msgin: 1-2-3-1. sym53c896-6-<0,0>: wide: wide=1 chg=0. sym53c896-6-<0,0>: sync msgout: 1-3-1-c-1f. sym53c896-6-<0,0>: sync msg in: 1-3-1-c-1f. sym53c896-6-<0,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-6-<0,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdj: 35566480 512-byte hdwr sectors (18210 MB) sdj: unknown partition table sym53c896-6-<1,0>: wide msgout: 1-2-3-1. sym53c896-6-<1,0>: wide msgin: 1-2-3-1. sym53c896-6-<1,0>: wide: wide=1 chg=0. sym53c896-6-<1,0>: wide msgout: 1-2-3-1. sym53c896-6-<1,0>: wide msgin: 1-2-3-1. sym53c896-6-<1,0>: wide: wide=1 chg=0. sym53c896-6-<1,0>: sync msgout: 1-3-1-c-1f. sym53c896-6-<1,0>: sync msg in: 1-3-1-c-1f. sym53c896-6-<1,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-6-<1,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdk: 35566480 512-byte hdwr sectors (18210 MB) sdk: unknown partition table sym53c896-6-<2,0>: wide msgout: 1-2-3-1. sym53c896-6-<2,0>: wide msgin: 1-2-3-1. sym53c896-6-<2,0>: wide: wide=1 chg=0. sym53c896-6-<2,0>: wide msgout: 1-2-3-1. sym53c896-6-<2,0>: wide msgin: 1-2-3-1. sym53c896-6-<2,0>: wide: wide=1 chg=0. sym53c896-6-<2,0>: sync msgout: 1-3-1-c-1f. sym53c896-6-<2,0>: sync msg in: 1-3-1-c-1f. sym53c896-6-<2,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-6-<2,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdl: 35566480 512-byte hdwr sectors (18210 MB) sdl: unknown partition table sym53c896-6-<3,0>: wide msgout: 1-2-3-1. sym53c896-6-<3,0>: wide msgin: 1-2-3-1. sym53c896-6-<3,0>: wide: wide=1 chg=0. sym53c896-6-<3,0>: wide msgout: 1-2-3-1. sym53c896-6-<3,0>: wide msgin: 1-2-3-1. sym53c896-6-<3,0>: wide: wide=1 chg=0. sym53c896-6-<3,0>: sync msgout: 1-3-1-c-1f. sym53c896-6-<3,0>: sync msg in: 1-3-1-c-1f. sym53c896-6-<3,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-6-<3,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdm: 35566480 512-byte hdwr sectors (18210 MB) sdm: unknown partition table sym53c896-6-<13,0>: wide msgout: 1-2-3-1. sym53c896-6-<13,0>: wide msgin: 1-2-3-1. sym53c896-6-<13,0>: wide: wide=1 chg=0. sym53c896-6-<13,0>: wide msgout: 1-2-3-1. sym53c896-6-<13,0>: wide msgin: 1-2-3-1. sym53c896-6-<13,0>: wide: wide=1 chg=0. sym53c896-6-<13,0>: sync msgout: 1-3-1-c-1f. sym53c896-6-<13,0>: sync msg in: 1-3-1-c-1f. sym53c896-6-<13,0>: sync: per=12 scntl3=0xb0 scntl4=0x0 ofs=31 fak=0 chg=0. sym53c896-6-<13,*>: FAST-20 WIDE SCSI 40.0 MB/s (50 ns, offset 31) SCSI device sdn: 35566480 512-byte hdwr sectors (18210 MB) sdn: unknown partition table Detected scsi generic sg1 at scsi2, channel 0, id 5, lun 0, type 3 Detected scsi generic sg10 at scsi4, channel 0, id 15, lun 0, type 13 Detected scsi generic sg16 at scsi6, channel 0, id 15, lun 0, type 13 NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP IP: routing cache hash table of 1024 buckets, 16Kbytes TCP: Hash tables configured (established 8192 bind 8192) Sending BOOTP requests.... OK IP-Config: Got BOOTP answer from 15.8.81.247, my address is 15.8.80.78 NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Switching from PDC console [ delete repeated text - A500 dumps kernel msg buffer here. ] kmem_create: Forcing size word alignment - nfs_fh Looking up port of RPC 100003/2 on 15.8.81.247 Looking up port of RPC 100005/2 on 15.8.81.247 VFS: Mounted root (nfs filesystem) readonly. INIT: version 2.78 booting Activating swap... Checking all file systems... Parallelizing fsck version 1.19 (13-Jul-2000) Setting kernel variables. Mounting local filesystems... not mounted anything hostname: can't open `(null)' Configuring network interfaces: done. Starting portmap daemon: portmap. Starting portmapper... do_page_fault() pid=51 command='sleep' YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI PSW: 00000000000001001111111100001011 r0-3 0000000000000000 00000000000039f8 0000000040122197 0000000000002000 r4-7 000000004017a938 000000000005a550 0000000000002000 000000002001fddc r8-11 0000000000000000 000000000008a810 000000002001fddc 0000000000000001 r12-15 0000000000000000 0000000000002564 000000000005a550 0000000000000000 r16-19 0000000000000000 0000000000002358 0000000000000000 000000004017a938 r20-23 0000000000000000 00000000000039f8 0000000000000031 000000000000002d r24-27 000000000000000d 000000004016fc72 000000002001ffe2 0000000000003838 r28-31 0000000000002564 0000000000004040 0000000020020280 0000000000000004 sr0-4 0000000000000380 0000000000000380 0000000000000000 0000000000000380 sr4-8 0000000000000380 0000000000000380 0000000000000380 0000000000000380 IASQ: 0000000000000380 0000000000000380 IAOQ: 000000004012231f 0000000040122323 IIR: 0e801014 ISR: 0000000000000380 IOR: 0000000000000000 ORIG_R28: 0000000000004000 /etc/init.d/rcS: line 80: 51 Segmentation fault sleep 2 Mounting remote filesystems... Setting the System Clock using the Hardware Clock as reference... Cannot access the Hardware Clock via any known method. Use the --debug option to see the details of our search for an access method. System Clock set. Local time: Wed Dec 6 22:52:37 MST 2000 Cleaning: /tmp /var/lock /var/run. Initializing random number generator... done. Recovering nvi editor sessions... done. INIT: Entering runlevel: 2 Starting system log daemon: syslogd do_page_fault() pid=95 command='syslogd' YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI PSW: 00000000000011101111111000001011 r0-3 0000000000000000 00000000000da490 000000004010188f 00000000000096c0 r4-7 00000000000d9490 000000004013d67c 00000000000096c0 0000000000000003 r8-11 0000000000009738 0000000000006800 000000004013e9dc 000000000008d2f0 r12-15 00000000200207cc 0000000000000000 000000000008d570 0000000000000000 r16-19 0000000000000000 0000000000000000 0000000000078440 00000000000d9490 r20-23 000000004013e9e8 000000004013e9e0 0000000000000a79 0000000040136a6c r24-27 000000000000973f 0000000000000000 0000000020022a88 0000000000008ec0 r28-31 00000000000025f3 000000000000a180 0000000020022a80 000000004004271b sr0-4 0000000000000280 0000000000000280 0000000000000000 0000000000000280 sr4-8 0000000000000280 0000000000000280 0000000000000280 0000000000000280 IASQ: 0000000000000280 0000000000000280 IAOQ: 000000004010188b 00000000400e8bcb IIR: 483a05d8 ISR: 0000000000000280 IOR: 00000000000da77c ORIG_R28: 0000000000000000 klogd. Starting Name Service Cache Daemon: nscd. Starting internet superserver: inetd. Debian GNU/Linux 2.2 gggA500 ttyS0 gggA500 login: root PAM_unix[115]: (login) session opened for user root by LOGIN(uid=0) PAM-lastlog[115]: /var/log/lastlog file is locked/read Last login: Wed Dec 6 19:22:50 2000 on ttyS0 Linux gggA500 2.4.0-test10 #6 Wed Dec 6 17:14:11 PST 2000 parisc64 unknown Most of the programs included with the Debian GNU/Linux system are freely redistributable; the exact distribution terms for each program are described in the individual files in /usr/doc/*/copyright Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. login[115]: ROOT LOGIN on `ttyS0' gggA500:~# cat /proc/cpuinfo processor : 0 cpu family : PA-RISC 2.0 cpu : PA8500 (PCX-W) cpu MHz : 440.000000 model : 9000/800/A500-44 model name : Crescendo 440 hversion : 0x00005cb0 sversion : 0x00000491 I-cache : 512 KB D-cache : 1024 KB (WB) ITLB entries : 160 DTLB entries : 160 - shared with ITLB bogomips : 878.18 gggA500:~# cat /proc/scsi/scsi Attached devices: Host: scsi1 Channel: 00 Id: 15 Lun: 00 Vendor: SEAGATE Model: ST39102LC Rev: 7C03 Type: Direct-Access ANSI SCSI revision: 02 Host: scsi2 Channel: 00 Id: 05 Lun: 00 Vendor: HP Model: D5989B Rev: 1.02 Type: Processor ANSI SCSI revision: 02 Host: scsi2 Channel: 00 Id: 13 Lun: 00 Vendor: HP Model: 9.10GB B 80-1205 Rev: Type: Direct-Access ANSI SCSI revision: 02 Host: scsi2 Channel: 00 Id: 14 Lun: 00 Vendor: HP Model: 9.10GB B 80-1205 Rev: Type: Direct-Access ANSI SCSI revision: 02 Host: scsi2 Channel: 00 Id: 15 Lun: 00 Vendor: HP Model: 9.10GB B 80-1205 Rev: Type: Direct-Access ANSI SCSI revision: 02 Host: scsi3 Channel: 00 Id: 15 Lun: 00 Vendor: SEAGATE Model: ST318404LC Rev: HP01 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi4 Channel: 00 Id: 00 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi4 Channel: 00 Id: 02 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi4 Channel: 00 Id: 03 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi4 Channel: 00 Id: 13 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi4 Channel: 00 Id: 15 Lun: 00 Vendor: HP Model: A5272A Rev: HP04 Type: Enclosure ANSI SCSI revision: 02 Host: scsi6 Channel: 00 Id: 00 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi6 Channel: 00 Id: 01 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi6 Channel: 00 Id: 02 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi6 Channel: 00 Id: 03 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi6 Channel: 00 Id: 13 Lun: 00 Vendor: IBM Model: DMVS18D Rev: HP05 Type: Direct-Access ANSI SCSI revision: 03 Host: scsi6 Channel: 00 Id: 15 Lun: 00 Vendor: HP Model: A5272A Rev: HP04 Type: Enclosure ANSI SCSI revision: 02 gggA500:~# ifconfig eth0 Link encap:Ethernet HWaddr 00:30:6E:03:79:9F inet addr:15.8.80.78 Bcast:15.8.87.255 Mask:255.255.248.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5236 errors:0 dropped:3 overruns:0 frame:0 TX packets:2238 errors:0 dropped:0 overruns:0 carrier:0 collisions:43 txqueuelen:100 Interrupt:128 gggA500:~# fdisk /dev/sda The number of cylinders for this disk is set to 8682. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): p Disk /dev/sda: 64 heads, 32 sectors, 8682 cylinders Units = cylinders of 2048 * 512 bytes Device Boot Start End Blocks Id System /dev/sda1 1 1025 1049584 82 Linux swap /dev/sda2 1026 1046 21504 f0 Unknown /dev/sda3 1047 5143 4195328 83 Linux /dev/sda4 5144 8682 3623936 83 Linux Command (m for help): q gggA500:~# mke2fs /dev/sda mke2fs 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09 /dev/sda is entire device, not just one partition! Proceed anyway? (y,n) n gggA500:~# set -o vi gggA500:~# mke2fs /dev/sda3 mke2fs 1.19, 13-Jul-2000 for EXT2 FS 0.5b, 95/08/09 warning: 256 blocks unused. Filesystem label= OS type: Linux Block size=4096 (log=2) Fragment size=4096 (log=2) 525312 inodes, 1048576 blocks 52441 blocks (5.00%) reserved for the super user First data block=0 32 block groups 32768 blocks per group, 32768 fragments per group 16416 inodes per group Superblock backups stored on blocks: 32768, 98304, 163840, 229376, 294912, 819200, 884736 Writing inode tables: 0/32 1/32 2/32 3/32 4/32 5/32 6/32 7/32 8/32 9/3210/3211/3212/3213/3214/3215/3216/3217/3218/3219/3220/3221/3222/3223/3224/3225/3226/3227/3228/3229/3230/3231/32done Writing superblocks and filesystem accounting information: done gggA500:~# mount /dev/sda3 /mnt gggA500:~# cd /mnt gggA500:/mnt# ls lost+found gggA500:/mnt# dd if=/palinux-0.5.iso of=/dev/sdc dd: writing to `/dev/sdc': No space left on device 7193+0 records in 7192+0 records out gggA500:/mnt# df Filesystem 1k-blocks Used Available Use% Mounted on 15.8.81.247:/tftpboot/hppa 7558400 5736960 1437488 80% / /dev/sda3 4128320 20 3918536 1% /mnt gggA500:/mnt# ls -l /dev/sdc brw-rw---- 1 root disk 8, 32 Aug 1 14:43 /dev/sdc gggA500:/mnt# fdisk /dev/sdc Device contains neither a valid DOS partition table, nor Sun, SGI or OSF disklabel Building a new DOS disklabel. Changes will remain in memory only, until you decide to write them. After that, of course, the previous content won't be recoverable. The number of cylinders for this disk is set to 8678. There is nothing wrong with that, but this is larger than 1024, and could in certain setups cause problems with: 1) software that runs at boot time (e.g., old versions of LILO) 2) booting and partitioning software from other OSs (e.g., DOS FDISK, OS/2 FDISK) Command (m for help): p Disk /dev/sdc: 64 heads, 32 sectors, 8678 cylinders Units = cylinders of 2048 * 512 bytes Device Boot Start End Blocks Id System Command (m for help): n Command action e extended p primary partition (1-4) p Partition number (1-4): 1 First cylinder (1-8678, default 1): Using default value 1 Last cylinder or +size or +sizeM or +sizeK (1-8678, default 8678): 2100 Command (m for help): n Command action e extended p primary partition (1-4) p Partition number (1-4): 2 First cylinder (2101-8678, default 2101): Using default value 2101 Last cylinder or +size or +sizeM or +sizeK (2101-8678, default 8678): 4200 Command (m for help): n Command action e extended p primary partition (1-4) p Partition number (1-4): 3 First cylinder (4201-8678, default 4201): Using default value 4201 Last cylinder or +size or +sizeM or +sizeK (4201-8678, default 8678): Using default value 8678 Command (m for help): p Disk /dev/sdc: 64 heads, 32 sectors, 8678 cylinders Units = cylinders of 2048 * 512 bytes Device Boot Start End Blocks Id System /dev/sdc1 1 2100 2150384 83 Linux /dev/sdc2 2101 4200 2150400 83 Linux /dev/sdc3 4201 8678 4585472 83 Linux Command (m for help): w The partition table has been altered! Calling ioctl() to re-read partition table. SCSI device sdc: 17773524 512-byte hdwr sectors (9100 MB) SCSI device sdc: 17773524 512-byte hdwr sectors (9100 MB) WARNING: If you have created or modified any DOS 6.x partitions, please see the fdisk manual page for additional information. Syncing disks. gggA500:/mnt# cd/ gggA500:/# dd if=/palinux-0.5.iso of=/dev/sdc1 bs=8k dd: writing `/dev/sdc1': No space left on device 3550+0 records in 3549+0 records out gggA500:/# sync gggA500:/# ls -l palinux-0.5.iso -rw-r--r-- 1 769 users 184612864 Nov 22 17:33 palinux-0.5.iso gggA500:/# du -s palinux-0.5.iso 180472 palinux-0.5.iso gggA500:/#