From: jheumann@fonts.de
To: parisc-linux@thepuffingroup.com
Subject: [parisc-linux] 0.9ser can't install on D210
Date: Tue, 05 Jun 2001 12:23:14 +0200 [thread overview]
Message-ID: <3B1CB312.1C9DBAB9@fonts.de> (raw)
please help,
i can't load linux pa-risc 0.9seriell on my HP9000/D210.
Why?
(HP-UX 10.20 is running....)
Jan Heumann
jheumann@fonts.de
-----------------------------------------------------
Main Menu: Enter command > search
Searching for potential boot device(s)...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type
----------- ----------------- -----------
P0 4.5 Random access media
P1 4.8 Random access media
P2 16/5.2 Random access media
P3 16/6.0 LAN Module
Main Menu: Enter command > boot p2
Interact with IPL (Y or N)?> n
Booting...
Boot IO Dependent Code (IODC) revision 1
IPL error: bad IPL checksum.
Error Reading IPL
Main Menu: Enter command > search
Searching for potential boot device(s)...
This may take several minutes.
To discontinue search, press any key (termination may not be immediate).
Path Number Device Path (dec) Device Type
----------- ----------------- -----------
P0 4.5 Random access media
P1 4.8 Random access media
P2 16/5.2 Random access media
P3 16/6.0 LAN Module
Main Menu: Enter command > boot p2
Interact with IPL (Y or N)?> y
Booting...
Boot IO Dependent Code (IODC) revision 1
IPL error: bad IPL checksum.
Error Reading IPL
--------------------------------------------------------
information all
PROCESSOR INFORMATION
HVERSION SVERSION CVERSION
Speed Model Model/Op (Revision)
--------- -------- -------- ----------
100 MHz 0x4840 0x0481 12
HSC Bus Speed (in MHz) : 33
Software ID (dec) : 2009187834
Software ID (hex) : 0x77c1c5fa
Software Capability : 0xf0
<Press any key to continue (q to quit)>
COPROCESSOR INFORMATION
Coprocessor Coprocessor Coprocessor
Model Revision State
----------- ----------- -------------
0x0000000d 1 Functional
CACHE INFORMATION
Instruction Cache Size Data Cache Size
----------------------- ---------------
128 KB 128 KB
<Press any key to continue (q to quit)>
MEMORY INFORMATION
Slot Card Size Amount Enabled
---- --------- --------------
0 64 MB 64 MB
1 64 MB 64 MB
2 64 MB 64 MB
3 64 MB 64 MB
4 64 MB 64 MB
5 64 MB 64 MB
Physical Memory: 384 MB (0x18000000)
Configured Memory: 384 MB (0x18000000)
<Press any key to continue (q to quit)>
I/O MODULE INFORMATION
IODC
IODC
Path (dec) Type Slot Mod HVERSION SVERSION Vers
Dep
---- ---- ---- --- -------- ---------- ------
------
4 A DMA I/O 1 0 0x0131 0x00008980 0x07
0x00
16 Bus Adapter 4 0 0x02e0 0x00008100 0x00
0x00
16/4 Built-in RS232 1 0 0x02e0 0x00008c00 0x01
0x00
16/5 Built-in SE SCSI 1 1 0x02e0 0x00008200 0x01
0x00
16/6 Built-in LAN 1 2 0x02e0 0x00008a00 0x02
0x00
16/0 Built-in Parallel 0 0 0x02e0 0x00007400 0x00
0x00
16/7 Built-in Keyboard 1 3 0x02e0 0x00008400 0x00
0x00
16/8 Built-in Mouse 2 0 0x02e0 0x00008400 0x00
0x00
20 Bus Adapter 5 0 0x0300 0x00008e00 0x00
0x00
20/2 RS232 Port 0 2 0x0300 0x00008c00 0x01
0x00
20/5 Bus Adapter 1 1 0x0300 0x00009000 0x00
0x00
<Press any key to continue (q to quit)>
Hot Swap module is present.
EISA Cards
Path Type EISA ID
---- ---- -------
20/5/1 EISA card 0x25d00400
20/5/2 EISA slot is empty
20/5/3 EISA slot is empty
20/5/4 EISA slot is empty
<Press any key to continue (q to quit)>
BOOT INFORMATION
Autoboot: ON
Autosearch: ON
Fastboot: OFF
Primary boot path: 4.8 (dec)
04.8 (hex)
Alternate boot path: 16/5.2 (dec)
10/05.2 (hex)
Console path: 16/4.0 (dec)
10/04.0 (hex)
Keyboard path: 16/7.0 (dec)
10/07.0 (hex)
LAN Station Address: 080009-af13c8
Mon Jan 5 21:15:36 GMT 1970 (19:70:01:05:21:15:36)
<Press any key to continue (q to quit)>
FIRMWARE INFORMATION
Firmware Version: 36.34
CHIP REVISIONS
Module Revision
------ --------
System Board 0
Processor Board 2
PA 7100LC 12
Firmware 20
Fast/Wide SCSI Board 1
Multifunction I/O Controller 0
EISA Interface 0
<Press any key to continue (q to quit)>
WARNINGS
No warnings to report.
Information Menu: Enter command >
next reply other threads:[~2001-06-05 12:25 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2001-06-05 10:23 jheumann [this message]
2001-06-05 12:47 ` [parisc-linux] 0.9ser can't install on D210 Richard Hirst
2001-06-05 13:00 ` Michael S.Zick
2001-06-05 12:57 ` Thomas Bogendoerfer
2001-06-05 21:04 ` Thomas Bogendoerfer
2001-06-11 13:21 ` jheumann
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3B1CB312.1C9DBAB9@fonts.de \
--to=jheumann@fonts.de \
--cc=parisc-linux@thepuffingroup.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox