From: Meelis Roos <mroos@linux.ee>
To: Grant Grundler <grundler@parisc-linux.org>
Cc: Randolph Chung <randolph@tausq.org>,
John David Anglin <dave@hiauly1.hia.nrc.ca>,
linux-parisc@vger.kernel.org
Subject: Re: HPPA hang with PCI SERR or PARITY enabling
Date: Sat, 29 Aug 2009 23:19:58 +0300 (EEST) [thread overview]
Message-ID: <Pine.SOC.4.64.0908292318050.12908@math.ut.ee> (raw)
In-Reply-To: <20090805174507.GB11458@lackof.org>
> > The real problem happens after tulip driver
> > loading and PCI configuration of the cards.
>
> This would be consistent with add-on cards not getting MMIO
> space assigned correctly. The ioread32() is one of several operations
> to configure the card.
>
> It would be helpful to know if 2.6.30.x kernels (from unstable)
> show the same problem.
Tried 2.6.30-6 kernels today. Uniprocessor parisc64 kernel behaves the
same. parisc64-smp kernel has an additional crash:
Command line for kernel: 'root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux-2.6.30-1-parisc64-smp'
Selected kernel: /vmlinux-2.6.30-1-parisc64-smp from partition 2
Selected ramdisk: /initrd.img-2.6.30-1-parisc64-smp from partition 2
ELF64 executable
Entry 00100000 first 00100000 n 3
Segment 0 load 00100000 size 4771840 mediaptr 0x1000
Segment 1 load 00618000 size 460848 mediaptr 0x48e000
Segment 2 load 0068c000 size 300800 mediaptr 0x4ff000
Loading ramdisk 8180633 bytes @ 3f821000...
Branching to kernel entry point 0x00100000. If this is the last
message you see, you may need to switch your console. This is
a common symptom -- search the FAQ and mailing list at parisc-linux.org
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.30-1-parisc64-smp (Debian 2.6.30-6) (waldi@debian.org) (gcc version 4.3.4 (GCC) ) #1 SMP Sun Aug 16 03:05:33 UTC 2009
[ 0.000000] unwind_init: start = 0x404b9144, end = 0x404e5214, entries = 11277
[ 0.000000] WARNING: Out of order unwind entry! 00000000404bb0c4 and 00000000404bb0d4
[ 0.000000] WARNING: Out of order unwind entry! 00000000404bb0d4 and 00000000404bb0e4
[ 0.000000] FP[0] enabled: Rev 1 Model 16
[ 0.000000] The 64-bit Kernel has started...
[ 0.000000] console [ttyB0] enabled
[ 0.000000] Initialized PDC Console for debugging.
[ 0.000000] Determining PDC firmware type: 64 bit PAT.
[ 0.000000] model 00005c90 00000491 00000000 00000002 2353fbcb 100000f0 00000008 000000b2 000000b2
[ 0.000000] vers 00000203
[ 0.000000] CPUID vers 17 rev 8 (0x00000228)
[ 0.000000] capabilities 0x1
[ 0.000000] model 9000/800/L1000-44
[ 0.000000] Total Memory: 3072 MB
[ 0.000000] initrd: 7f821000-7ffee399
[ 0.000000] initrd: reserving 3f821000-3ffee399 (mem_max c0000000)
[ 0.000000] SMP: bootstrap CPU ID is 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 775680
[ 0.000000] Kernel command line: root=/dev/sda5 HOME=/ console=ttyS0 TERM=vt102 palo_kernel=2/vmlinux-2.6.30-1-parisc64-smp
[ 0.000000] NR_IRQS:128
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] Console: colour dummy device 160x64
[ 0.028000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.064000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.580000] Memory: 3075452k/3145728k available (3144k kernel code, 69636k reserved, 1467k data, 296k init)
[ 0.588000] virtual kernel memory layout:
[ 0.588000] vmalloc : 0x0000000000008000 - 0x000000003f000000 (1007 MB)
[ 0.588000] memory : 0x0000000040000000 - 0x0000000100000000 (3072 MB)
[ 0.588000] .init : 0x000000004068c000 - 0x00000000406d6000 ( 296 kB)
[ 0.588000] .data : 0x0000000040412118 - 0x0000000040581000 (1467 kB)
[ 0.588000] .text : 0x0000000040100000 - 0x0000000040412118 (3144 kB)
[ 0.660000] Calibrating delay loop... 876.54 BogoMIPS (lpj=1753088)
[ 0.756000] Security Framework initialized
[ 0.764000] SELinux: Disabled at boot.
[ 0.776000] Mount-cache hash table entries: 256
[ 0.784000] Initializing cgroup subsys ns
[ 0.876000] Initializing cgroup subsys cpuacct
[ 0.884000] Initializing cgroup subsys devices
[ 0.892000] Initializing cgroup subsys freezer
[ 0.896000] Initializing cgroup subsys net_cls
[ 0.904000] Brought up 1 CPUs
[ 1.160000] net_namespace: 1928 bytes
[ 1.168000] regulator: core version 0.5
[ 1.176000] NET: Registered protocol family 16
[ 1.300000] EISA bus registered
[ 1.304000] Searching for devices...
[ 1.772000] Found devices:
[ 1.772000] 1. Rhapsody DC- 440 at 0xfffffffffffa0000 [160] { 0, 0x0, 0x5c9, 0x00004 }
[ 1.780000] 2. Rhapsody DC- 440 at 0xfffffffffffa6000 [166] { 0, 0x0, 0x5c9, 0x00004 }
[ 1.788000] 3. Memory at 0xfffffffffed08000 [8] { 1, 0x0, 0x095, 0x00009 }
[ 1.792000] 4. Astro BC Runway Port at 0xfffffffffed00000 [0] { 12, 0x0, 0x582, 0x0000b }
[ 1.800000] 5. Elroy PCI Bridge at 0xfffffffffed30000 [0/0] { 13, 0x0, 0x782, 0x0000a }
[ 1.868000] 6. Elroy PCI Bridge at 0xfffffffffed32000 [0/1] { 13, 0x0, 0x782, 0x0000a }
[ 1.876000] 7. Elroy PCI Bridge at 0xfffffffffed34000 [0/2] { 13, 0x0, 0x782, 0x0000a }
[ 1.884000] 8. Elroy PCI Bridge at 0xfffffffffed36000 [0/3] { 13, 0x0, 0x782, 0x0000a }
[ 1.892000] 9. Elroy PCI Bridge at 0xfffffffffed38000 [0/4] { 13, 0x0, 0x782, 0x0000a }
[ 1.900000] 10. Elroy PCI Bridge at 0xfffffffffed3a000 [0/5] { 13, 0x0, 0x782, 0x0000a }
[ 2.432000] 11. Elroy PCI Bridge at 0xfffffffffed3c000 [0/6] { 13
********** VIRTUAL FRONT PANEL **********
System Boot detected
*****************************************
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH FLASH ON ON
LED State: Unexpected Reboot. Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
processor system initialization 1C00
*****************************************
************ EARLY BOOT VFP *************
End of early boot detected
*****************************************
[ 3.132000] powersw: Soft power switch support not available.
[ 3.144000] bio: create slab <bio-0> at 0
[ 3.292000] NET: Registered protocol family 2
[ 3.348000] IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 3.356000] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 3.440000] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 3.564000] TCP: Hash tables configured (established 262144 bind 65536)
[ 3.568000] TCP reno registered
[ 3.584000] NET: Registered protocol family 1
[ 3.696000] Trying to unpack rootfs image as initramfs...
[ 4.732000] Freeing initrd memory: 7988k freed
[ 4.740000] Chassis warnings not supported.
[ 4.748000] Performance monitoring counters enabled for Rhapsody DC- 440
[ 4.764000] audit: initializing netlink socket (disabled)
[ 4.772000] type=2000 audit(1251556747.242:1): initialized
[ 4.788000] VFS: Disk quotas dquot_6.5.2
[ 4.796000] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 4.816000] msgmni has been set to 6023
[ 4.828000] alg: No test for stdrng (krng)
[ 4.836000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 4.848000] io scheduler noop registered
[ 4.856000] io scheduler anticipatory registered
[ 4.860000] io scheduler deadline registered
[ 4.864000] io scheduler cfq registered (default)
[ 4.960000] PDC Stable Storage facility v0.30
[ 5.652000] STI GSC/PCI core graphics driver Version 0.9a
[ 5.684000] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 5.692000] serial 0000:00:04.0: enabling device (0146 -> 0147)
[ 5.704000] 0000:00:04.0: ttyS0 at MMIO 0xfffffffff8000000 (irq = 70) is a 16550A
[ 5.712000] console handover: boot [ttyB0] -> real [ttyS0]
[ 5.728000] 0000:00:04.0: ttyS1 at MMIO 0xfffffffff8000008 (irq = 70) is a 16550A
[ 5.752000] 0000:00:04.0: ttyS2 at MMIO 0xfffffffff8000010 (irq = 70) is a 16550A
[ 5.764000] serial 0000:00:05.0: enabling device (0000 -> 0003)
[ 5.776000] serial 0000:00:05.0: enabling SERR and PARITY (0003 -> 0143)
[ 5.792000] 0000:00:05.0: ttyS3 at MMIO 0xfffffffff8005000 (irq = 71) is a 16550A
[ 5.804000] Couldn't register serial port 0000:00:05.0: -28
[ 5.908000] brd: module loaded
[ 5.912000] mice: PS/2 mouse device common for all mice
[ 6.032000] rtc-generic rtc-generic: rtc core: registered rtc-generic as rtc0
[ 6.048000] TCP cubic registered
[ 6.172000] NET: Registered protocol family 17
[ 6.184000] registered taskstats version 1
[ 6.196000] rtc-generic rtc-generic: setting system clock to 2009-08-29 14:39:08 UTC (1251556748)
[ 6.316000] Freeing unused kernel memory: <0>------------[ cut here ]------------
[ 6.464000] Badness at /build/buildd/linux-2.6-2.6.30/debian/build/source_hppa_none/kernel/smp.c:369
[ 6.476000]
[ 6.480000] YZrvWESTHLNXBCVMcbcbcbcbOGFRQPDI
[ 6.484000] PSW: 00001000000001100000000000001110 Not tainted
[ 6.488000] r00-03 000000000806000e 0000000040686fc0 0000000040182c3c 000000004058d020
[ 6.496000] r04-07 0000000040668fc0 000000004065e7e0 00000000404f7db0 0000000000000000
[ 6.504000] r08-11 0000000040686fc0 000000000000000 00000000406797c0
[ 7.028000] r12-15 0000000000000001 0000000000000001 0000000000000000 0000000000000001
[ 7.040000] r16-19 00000000f00003b0 0000000040686fc0 00000000ff83eb40 00000000406d6000
[ 7.048000] r20-23 0000000000000000 00000000406d6000 ffffffffffffffff 0000000000000001
[ 7.056000] r24-27 0000000000000000 000000004065e7e0 00000000404f7db0 0000000040668fc0
[ 7.064000] r28-31 0000000000000000 00000000ff840490 00000000ff840580 0000000000000000
[ 7 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 7.592000] sr04-07 0000000000000000 0000000000000000 0000000000000000 0000000000000000
[ 7.608000]
[ 7.608000] IASQ: 0000000000000000 0000000000000000 IAOQ: 0000000040182984 0000000040182988
[ 7.616000] IIR: 03ffe01f ISR: 0000000000000000 IOR: 0000000000000000
[ 7.624000] CPU: 0 CR30: 00000000ff840000 CR31: 0000000000008020
[ 7.628000] ORIG_R28: 000000000800000e
[ 7.632000] function_many+0x7c/0x2f8
[ 8.152000] IAOQ[1]: smp_call_function_many+0x80/0x2f8
[ 8.164000] RP(r2): smp_call_function+0x3c/0x50
[ 8.168000] Backtrace:
[ 8.168000] Backtrace:
[ 8.168000] [<0000000040115fe8>] printk+0x40/0x50
[ 8.168000] <0000000040152698>] print_tainted+0xc0/0xe0
[ 8.168000] [<0000000040104084>] intr_check_sig+0x0/0x38
[ 8.168000] [<0000000040104074>] intr_return+0x0/0x4
[ 8.168000] [<0000000040182c3c>] smp_call_function+0x3c/0x50
[ 8.168000] [<0000000040159c40>] on_each_cpu+0x28/0x68
[ 8.168000] [<000000004011b95c>] free_initmem+0x94/0x340
--
Meelis Roos (mroos@linux.ee)
next prev parent reply other threads:[~2009-08-29 20:19 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2009-06-15 10:24 HPPA hang with PCI SERR or PARITY enabling Meelis Roos
2009-06-15 13:45 ` John David Anglin
2009-07-30 17:58 ` Meelis Roos
2009-07-31 1:25 ` Randolph Chung
2009-07-31 1:45 ` John David Anglin
2009-07-31 6:28 ` Meelis Roos
2009-07-31 9:35 ` Thibaut VARENE
2009-07-31 14:46 ` John David Anglin
2009-07-31 14:50 ` John David Anglin
2009-07-31 23:16 ` Meelis Roos
2009-08-01 20:59 ` John David Anglin
2009-08-05 17:45 ` Grant Grundler
2009-08-05 19:42 ` Meelis Roos
2009-08-06 12:15 ` Bernd Gietzelt
2009-08-07 16:22 ` Grant Grundler
2009-08-08 9:31 ` Bernd Gietzelt
2009-08-09 5:27 ` Grant Grundler
2009-08-10 1:22 ` Randolph Chung
2009-08-10 8:01 ` Thibaut VARENE
2009-08-10 8:09 ` Thibaut VARENE
2009-08-10 11:08 ` Bernd Gietzelt
2009-08-10 11:18 ` Thibaut VARENE
2009-08-10 11:57 ` Bernd Gietzelt
2009-08-10 23:20 ` Grant Grundler
2009-08-11 9:27 ` Thibaut VARENE
2009-08-10 8:26 ` Bernd Gietzelt
2009-08-07 16:36 ` Grant Grundler
2009-08-29 20:19 ` Meelis Roos [this message]
2009-06-15 14:06 ` John David Anglin
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Pine.SOC.4.64.0908292318050.12908@math.ut.ee \
--to=mroos@linux.ee \
--cc=dave@hiauly1.hia.nrc.ca \
--cc=grundler@parisc-linux.org \
--cc=linux-parisc@vger.kernel.org \
--cc=randolph@tausq.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox