From: Christoph Fritz <chf.fritz@googlemail.com>
To: Richard Zhu <hongxing.zhu@nxp.com>,
Lucas Stach <l.stach@pengutronix.de>,
Shawn Guo <shawnguo@kernel.org>,
Fabio Estevam <fabio.estevam@nxp.com>,
Bjorn Helgaas <bhelgaas@google.com>,
Lee Jones <lee.jones@linaro.org>
Cc: linux-pci@vger.kernel.org, linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 2/2] PCI: imx6: add initial imx6sx support
Date: Thu, 25 Feb 2016 15:47:49 +0100 [thread overview]
Message-ID: <1456411669-4699-3-git-send-email-chf.fritz@googlemail.com> (raw)
In-Reply-To: <1456411669-4699-1-git-send-email-chf.fritz@googlemail.com>
This patch adds initial PCIe support for the imx6 SoC derivate imx6sx.
PCI_MSI support is untested as its necessary suspend/resume quirk is
left out of this patch.
This patch is heavily based on patches by Richard Zhu.
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
---
.../devicetree/bindings/pci/fsl,imx6q-pcie.txt | 6 +-
drivers/pci/host/pci-imx6.c | 130 ++++++++++++++-------
2 files changed, 96 insertions(+), 40 deletions(-)
diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
index 6fbba53..c4323be 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
@@ -4,7 +4,7 @@ This PCIe host controller is based on the Synopsis Designware PCIe IP
and thus inherits all the common properties defined in designware-pcie.txt.
Required properties:
-- compatible: "fsl,imx6q-pcie"
+- compatible: "fsl,imx6q-pcie", "fsl,imx6sx-pcie"
- reg: base addresse and length of the pcie controller
- interrupts: A list of interrupt outputs of the controller. Must contain an
entry for each entry in the interrupt-names property.
@@ -13,6 +13,10 @@ Required properties:
- clock-names: Must include the following additional entries:
- "pcie_phy"
+Additional required properties for imx6sx-pcie:
+- clock names: Must include the following additional entries:
+ - "pcie_inbound_axi"
+
Example:
pcie@0x01000000 {
diff --git a/drivers/pci/host/pci-imx6.c b/drivers/pci/host/pci-imx6.c
index fe60096..7e634a6 100644
--- a/drivers/pci/host/pci-imx6.c
+++ b/drivers/pci/host/pci-imx6.c
@@ -35,9 +35,11 @@ struct imx6_pcie {
struct gpio_desc *reset_gpio;
struct clk *pcie_bus;
struct clk *pcie_phy;
+ struct clk *pcie_inbound_axi;
struct clk *pcie;
struct pcie_port pp;
struct regmap *iomuxc_gpr;
+ bool is_imx6sx;
void __iomem *mem_base;
};
@@ -214,35 +216,46 @@ static int imx6_pcie_assert_core_reset(struct pcie_port *pp)
struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
u32 val, gpr1, gpr12;
- /*
- * If the bootloader already enabled the link we need some special
- * handling to get the core back into a state where it is safe to
- * touch it for configuration. As there is no dedicated reset signal
- * wired up for MX6QDL, we need to manually force LTSSM into "detect"
- * state before completely disabling LTSSM, which is a prerequisite
- * for core configuration.
- *
- * If both LTSSM_ENABLE and REF_SSP_ENABLE are active we have a strong
- * indication that the bootloader activated the link.
- */
- regmap_read(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1, &gpr1);
- regmap_read(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, &gpr12);
-
- if ((gpr1 & IMX6Q_GPR1_PCIE_REF_CLK_EN) &&
- (gpr12 & IMX6Q_GPR12_PCIE_CTL_2)) {
- val = readl(pp->dbi_base + PCIE_PL_PFLR);
- val &= ~PCIE_PL_PFLR_LINK_STATE_MASK;
- val |= PCIE_PL_PFLR_FORCE_LINK;
- writel(val, pp->dbi_base + PCIE_PL_PFLR);
-
+ if (imx6_pcie->is_imx6sx) {
regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
- IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
- }
+ IMX6SX_GPR12_PCIE_TEST_POWERDOWN,
+ IMX6SX_GPR12_PCIE_TEST_POWERDOWN);
+ /* Force PCIe PHY reset */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
+ IMX6SX_GPR5_PCIE_BTNRST_RESET,
+ IMX6SX_GPR5_PCIE_BTNRST_RESET);
+ } else {
+ /*
+ * If the bootloader already enabled the link we need some
+ * special handling to get the core back into a state where
+ * it is safe to touch it for configuration. As there is no
+ * dedicated reset signal to manually force LTSSM into "detect"
+ * state before completely disabling LTSSM, which is a
+ * prerequisite for core configuration.
+ *
+ * If both LTSSM_ENABLE and REF_SSP_ENABLE are active we have
+ * a strong indication that the bootloader activated the link.
+ */
+ regmap_read(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1, &gpr1);
+ regmap_read(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12, &gpr12);
+
+ if ((gpr1 & IMX6Q_GPR1_PCIE_REF_CLK_EN) &&
+ (gpr12 & IMX6Q_GPR12_PCIE_CTL_2)) {
+ val = readl(pp->dbi_base + PCIE_PL_PFLR);
+ val &= ~PCIE_PL_PFLR_LINK_STATE_MASK;
+ val |= PCIE_PL_PFLR_FORCE_LINK;
+ writel(val, pp->dbi_base + PCIE_PL_PFLR);
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6Q_GPR12_PCIE_CTL_2, 0);
+ }
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
- IMX6Q_GPR1_PCIE_TEST_PD, 1 << 18);
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
- IMX6Q_GPR1_PCIE_REF_CLK_EN, 0 << 16);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_TEST_PD,
+ IMX6Q_GPR1_PCIE_TEST_PD);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN, 0);
+ }
return 0;
}
@@ -270,18 +283,30 @@ static int imx6_pcie_deassert_core_reset(struct pcie_port *pp)
goto err_pcie;
}
- /* power up core phy and enable ref clock */
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
- IMX6Q_GPR1_PCIE_TEST_PD, 0 << 18);
- /*
- * the async reset input need ref clock to sync internally,
- * when the ref clock comes after reset, internal synced
- * reset time is too short, cannot meet the requirement.
- * add one ~10us delay here.
- */
- udelay(10);
- regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
- IMX6Q_GPR1_PCIE_REF_CLK_EN, 1 << 16);
+ if (imx6_pcie->is_imx6sx) {
+ ret = clk_prepare_enable(imx6_pcie->pcie_inbound_axi);
+ if (ret) {
+ dev_err(pp->dev, "unable to enable pcie_axi clock\n");
+ goto err_inbound_axi;
+ }
+
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6SX_GPR12_PCIE_TEST_POWERDOWN, 0);
+ } else {
+ /* power up core phy and enable ref clock */
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_TEST_PD, 0);
+ /*
+ * the async reset input need ref clock to sync internally,
+ * when the ref clock comes after reset, internal synced
+ * reset time is too short , cannot meet the requirement.
+ * add one ~10us delay here.
+ */
+ udelay(10);
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR1,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN,
+ IMX6Q_GPR1_PCIE_REF_CLK_EN);
+ }
/* allow the clocks to stabilize */
usleep_range(200, 500);
@@ -292,8 +317,15 @@ static int imx6_pcie_deassert_core_reset(struct pcie_port *pp)
msleep(100);
gpiod_set_value_cansleep(imx6_pcie->reset_gpio, 1);
}
+
+ if (imx6_pcie->is_imx6sx)
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR5,
+ IMX6SX_GPR5_PCIE_BTNRST_RESET, 0);
+
return 0;
+err_inbound_axi:
+ clk_disable_unprepare(imx6_pcie->pcie);
err_pcie:
clk_disable_unprepare(imx6_pcie->pcie_bus);
err_pcie_bus:
@@ -307,6 +339,12 @@ static void imx6_pcie_init_phy(struct pcie_port *pp)
{
struct imx6_pcie *imx6_pcie = to_imx6_pcie(pp);
+ if (imx6_pcie->is_imx6sx) {
+ regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
+ IMX6SX_GPR12_PCIE_RX_EQ_MASK,
+ IMX6SX_GPR12_PCIE_RX_EQ_2);
+ }
+
regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
IMX6Q_GPR12_PCIE_CTL_2, 0 << 10);
@@ -571,6 +609,9 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
pp = &imx6_pcie->pp;
pp->dev = &pdev->dev;
+ imx6_pcie->is_imx6sx = of_device_is_compatible(pp->dev->of_node,
+ "fsl,imx6sx-pcie");
+
/* Added for PCI abort handling */
hook_fault_code(16 + 6, imx6q_pcie_abort_handler, SIGBUS, 0,
"imprecise external abort");
@@ -606,6 +647,16 @@ static int __init imx6_pcie_probe(struct platform_device *pdev)
return PTR_ERR(imx6_pcie->pcie);
}
+ if (imx6_pcie->is_imx6sx) {
+ imx6_pcie->pcie_inbound_axi = devm_clk_get(&pdev->dev,
+ "pcie_inbound_axi");
+ if (IS_ERR(imx6_pcie->pcie_inbound_axi)) {
+ dev_err(&pdev->dev,
+ "pcie_incbound_axi clock missing or invalid\n");
+ return PTR_ERR(imx6_pcie->pcie_inbound_axi);
+ }
+ }
+
/* Grab GPR config register range */
imx6_pcie->iomuxc_gpr =
syscon_regmap_lookup_by_compatible("fsl,imx6q-iomuxc-gpr");
@@ -632,6 +683,7 @@ static void imx6_pcie_shutdown(struct platform_device *pdev)
static const struct of_device_id imx6_pcie_of_match[] = {
{ .compatible = "fsl,imx6q-pcie", },
+ { .compatible = "fsl,imx6sx-pcie", },
{},
};
MODULE_DEVICE_TABLE(of, imx6_pcie_of_match);
--
2.1.4
next prev parent reply other threads:[~2016-02-25 14:48 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-02-25 14:47 [PATCH v3 0/2] Add PCIe driver support for imx6sx Christoph Fritz
2016-02-25 14:47 ` [PATCH v3 1/2] MFD: imx6sx: Add PCIe register definitions for iomuxc gpr Christoph Fritz
2016-03-08 4:32 ` Lee Jones
2016-02-25 14:47 ` Christoph Fritz [this message]
2016-03-11 17:58 ` [PATCH v3 2/2] PCI: imx6: add initial imx6sx support Bjorn Helgaas
2016-03-13 23:26 ` Christoph Fritz
2016-03-13 23:30 ` PCI: imx6: Factor out ref clock enable Christoph Fritz
2016-03-20 7:29 ` Christoph Fritz
2016-04-05 21:56 ` Bjorn Helgaas
2016-03-13 23:31 ` [PATCH v4] PCI: imx6: Add initial imx6sx support Christoph Fritz
2016-03-20 7:30 ` Christoph Fritz
2016-04-05 21:56 ` Bjorn Helgaas
2016-03-03 1:41 ` [PATCH v3 0/2] Add PCIe driver support for imx6sx Christoph Fritz
2016-03-03 1:46 ` Richard Zhu
2016-03-03 1:48 ` Richard Zhu
2016-03-07 8:20 ` Christoph Fritz
2016-03-09 15:39 ` Christoph Fritz
2016-03-09 15:53 ` Lucas Stach
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1456411669-4699-3-git-send-email-chf.fritz@googlemail.com \
--to=chf.fritz@googlemail.com \
--cc=bhelgaas@google.com \
--cc=fabio.estevam@nxp.com \
--cc=hongxing.zhu@nxp.com \
--cc=l.stach@pengutronix.de \
--cc=lee.jones@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-pci@vger.kernel.org \
--cc=shawnguo@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).