* [PATCH 1/4] dt-bindings: pci: tegra: Document Tegra186 PCIe DT
2017-09-20 6:42 [PATCH 0/4] Add Tegra186 PCIe support Manikanta Maddireddy
@ 2017-09-20 6:42 ` Manikanta Maddireddy
2017-09-20 6:42 ` [PATCH 2/4] PCI: tegra: Add Tegra186 PCIe support Manikanta Maddireddy
` (3 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Manikanta Maddireddy @ 2017-09-20 6:42 UTC (permalink / raw)
To: bhelgaas, thierry.reding, jonathanh
Cc: linux-tegra, linux-pci, Manikanta Maddireddy
Tegra186 PCIe controller DT properties has couple of differences
wrt Tegra210 PCIe, rest of the DT properties are same.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
---
.../bindings/pci/nvidia,tegra20-pcie.txt | 134 ++++++++++++++++++++-
1 file changed, 130 insertions(+), 4 deletions(-)
diff --git a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
index 982a74ea6df9..753b67327373 100644
--- a/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/nvidia,tegra20-pcie.txt
@@ -1,10 +1,15 @@
NVIDIA Tegra PCIe controller
Required properties:
-- compatible: For Tegra20, must contain "nvidia,tegra20-pcie". For Tegra30,
- "nvidia,tegra30-pcie". For Tegra124, must contain "nvidia,tegra124-pcie".
- Otherwise, must contain "nvidia,<chip>-pcie", plus one of the above, where
- <chip> is tegra132 or tegra210.
+- compatible: Must be:
+ - "nvidia,tegra20-pcie": for Tegra20
+ - "nvidia,tegra30-pcie": for Tegra30
+ - "nvidia,tegra124-pcie": for Tegra124 and Tegra132
+ - "nvidia,tegra210-pcie": for Tegra210
+ - "nvidia,tegra186-pcie": for Tegra186
+- power-domains: To ungate power partition by BPMP powergate driver. Must
+contain BPMP phandle and PCIe power partition ID. This is required only
+for Tegra186.
- device_type: Must be "pci"
- reg: A list of physical base address and length for each set of controller
registers. Must contain an entry for each entry in the reg-names property.
@@ -124,6 +129,16 @@ Power supplies for Tegra210:
- vddio-pex-ctl-supply: Power supply for PCIe control I/O partition. Must
supply 1.8 V.
+Power supplies for Tegra186:
+- Required:
+ - dvdd-pex-supply: Power supply for digital PCIe I/O. Must supply 1.05 V.
+ - hvdd-pex-pll-supply: High-voltage supply for PLLE (shared with USB3). Must
+ supply 1.8 V.
+ - hvdd-pex-supply: High-voltage supply for PCIe I/O and PCIe output clocks.
+ Must supply 1.8 V.
+ - vddio-pexctl-aud-supply: Power supply for PCIe side band signals. Must
+ supply 1.8 V.
+
Root ports are defined as subnodes of the PCIe controller node.
Required properties:
@@ -546,3 +561,114 @@ Board DTS:
status = "okay";
};
};
+
+Tegra186:
+---------
+
+SoC DTSI:
+
+ pcie@10003000 {
+ compatible = "nvidia,tegra186-pcie";
+ power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>;
+ device_type = "pci";
+ reg = <0x0 0x10003000 0x0 0x00000800 /* PADS registers */
+ 0x0 0x10003800 0x0 0x00000800 /* AFI registers */
+ 0x0 0x40000000 0x0 0x10000000>; /* configuration space */
+ reg-names = "pads", "afi", "cs";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+ interrupt-names = "intr", "msi";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+ bus-range = <0x00 0xff>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000 /* port 0 configuration space */
+ 0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000 /* port 1 configuration space */
+ 0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000 /* port 2 configuration space */
+ 0x81000000 0 0x0 0x0 0x50000000 0 0x00010000 /* downstream I/O (64 KiB) */
+ 0x82000000 0 0x50100000 0x0 0x50100000 0 0x07F00000 /* non-prefetchable memory (127 MiB) */
+ 0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */
+
+ clocks = <&bpmp TEGRA186_CLK_AFI>,
+ <&bpmp TEGRA186_CLK_PCIE>,
+ <&bpmp TEGRA186_CLK_PLLE>;
+ clock-names = "afi", "pex", "pll_e";
+
+ resets = <&bpmp TEGRA186_RESET_AFI>,
+ <&bpmp TEGRA186_RESET_PCIE>,
+ <&bpmp TEGRA186_RESET_PCIEXCLK>;
+ reset-names = "afi", "pex", "pcie_x";
+
+ status = "disabled";
+
+ pci@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>;
+ reg = <0x000800 0 0 0 0>;
+ status = "disabled";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ nvidia,num-lanes = <2>;
+ };
+
+ pci@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>;
+ reg = <0x001000 0 0 0 0>;
+ status = "disabled";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ nvidia,num-lanes = <1>;
+ };
+
+ pci@3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>;
+ reg = <0x001800 0 0 0 0>;
+ status = "disabled";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ nvidia,num-lanes = <1>;
+ };
+ };
+
+Board DTS:
+
+ pcie@10003000 {
+ status = "okay";
+
+ dvdd-pex-supply = <&vdd_pex>;
+ hvdd-pex-pll-supply = <&vdd_1v8>;
+ hvdd-pex-supply = <&vdd_1v8>;
+ vddio-pexctl-aud-supply = <&vdd_1v8>;
+
+ pci@1,0 {
+ nvidia,num-lanes = <4>;
+ status = "okay";
+ };
+
+ pci@2,0 {
+ nvidia,num-lanes = <0>;
+ status = "disabled";
+ };
+
+ pci@3,0 {
+ nvidia,num-lanes = <1>;
+ status = "disabled";
+ };
+ };
--
2.1.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 2/4] PCI: tegra: Add Tegra186 PCIe support
2017-09-20 6:42 [PATCH 0/4] Add Tegra186 PCIe support Manikanta Maddireddy
2017-09-20 6:42 ` [PATCH 1/4] dt-bindings: pci: tegra: Document Tegra186 PCIe DT Manikanta Maddireddy
@ 2017-09-20 6:42 ` Manikanta Maddireddy
2017-09-20 6:42 ` [PATCH 3/4] arm64: tegra: Add PCIe node for Tegra186 Manikanta Maddireddy
` (2 subsequent siblings)
4 siblings, 0 replies; 6+ messages in thread
From: Manikanta Maddireddy @ 2017-09-20 6:42 UTC (permalink / raw)
To: bhelgaas, thierry.reding, jonathanh
Cc: linux-tegra, linux-pci, Manikanta Maddireddy
UPHY programming is performed by BPMP, PHY enable calls are
not required for Tegra186 PCIe. Power partition ungate is
done by BPMP powergate driver.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
---
drivers/pci/host/pci-tegra.c | 123 +++++++++++++++++++++++++++++++++++--------
1 file changed, 102 insertions(+), 21 deletions(-)
diff --git a/drivers/pci/host/pci-tegra.c b/drivers/pci/host/pci-tegra.c
index 9c40da54f88a..b45466fe943f 100644
--- a/drivers/pci/host/pci-tegra.c
+++ b/drivers/pci/host/pci-tegra.c
@@ -159,10 +159,13 @@
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_SINGLE (0x0 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_420 (0x0 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_X2_X1 (0x0 << 20)
+#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_401 (0x0 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_DUAL (0x1 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_222 (0x1 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_X4_X1 (0x1 << 20)
+#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_211 (0x1 << 20)
#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_411 (0x2 << 20)
+#define AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_111 (0x2 << 20)
#define AFI_FUSE 0x104
#define AFI_FUSE_PCIE_T0_GEN2_DIS (1 << 2)
@@ -252,6 +255,7 @@ struct tegra_pcie_soc {
bool has_cml_clk;
bool has_gen2;
bool force_pca_enable;
+ bool program_uphy;
};
static inline struct tegra_msi *to_tegra_msi(struct msi_controller *chip)
@@ -1012,10 +1016,12 @@ static int tegra_pcie_enable_controller(struct tegra_pcie *pcie)
afi_writel(pcie, value, AFI_FUSE);
}
- err = tegra_pcie_phy_power_on(pcie);
- if (err < 0) {
- dev_err(dev, "failed to power on PHY(s): %d\n", err);
- return err;
+ if (soc->program_uphy) {
+ err = tegra_pcie_phy_power_on(pcie);
+ if (err < 0) {
+ dev_err(dev, "failed to power on PHY(s): %d\n", err);
+ return err;
+ }
}
/* take the PCIe interface module out of reset */
@@ -1048,19 +1054,23 @@ static int tegra_pcie_enable_controller(struct tegra_pcie *pcie)
static void tegra_pcie_power_off(struct tegra_pcie *pcie)
{
struct device *dev = pcie->dev;
+ const struct tegra_pcie_soc *soc = pcie->soc;
int err;
/* TODO: disable and unprepare clocks? */
- err = tegra_pcie_phy_power_off(pcie);
- if (err < 0)
- dev_err(dev, "failed to power off PHY(s): %d\n", err);
+ if (soc->program_uphy) {
+ err = tegra_pcie_phy_power_off(pcie);
+ if (err < 0)
+ dev_err(dev, "failed to power off PHY(s): %d\n", err);
+ }
reset_control_assert(pcie->pcie_xrst);
reset_control_assert(pcie->afi_rst);
reset_control_assert(pcie->pex_rst);
- tegra_powergate_power_off(TEGRA_POWERGATE_PCIE);
+ if (!dev->pm_domain)
+ tegra_powergate_power_off(TEGRA_POWERGATE_PCIE);
err = regulator_bulk_disable(pcie->num_supplies, pcie->supplies);
if (err < 0)
@@ -1077,19 +1087,29 @@ static int tegra_pcie_power_on(struct tegra_pcie *pcie)
reset_control_assert(pcie->afi_rst);
reset_control_assert(pcie->pex_rst);
- tegra_powergate_power_off(TEGRA_POWERGATE_PCIE);
+ if (!dev->pm_domain)
+ tegra_powergate_power_off(TEGRA_POWERGATE_PCIE);
/* enable regulators */
err = regulator_bulk_enable(pcie->num_supplies, pcie->supplies);
if (err < 0)
dev_err(dev, "failed to enable regulators: %d\n", err);
- err = tegra_powergate_sequence_power_up(TEGRA_POWERGATE_PCIE,
- pcie->pex_clk,
- pcie->pex_rst);
- if (err) {
- dev_err(dev, "powerup sequence failed: %d\n", err);
- return err;
+ if (dev->pm_domain) {
+ err = clk_prepare_enable(pcie->pex_clk);
+ if (err) {
+ dev_err(dev, "failed to enable PEX clock: %d\n", err);
+ return err;
+ }
+ reset_control_deassert(pcie->pex_rst);
+ } else {
+ err = tegra_powergate_sequence_power_up(TEGRA_POWERGATE_PCIE,
+ pcie->pex_clk,
+ pcie->pex_rst);
+ if (err) {
+ dev_err(dev, "powerup sequence failed: %d\n", err);
+ return err;
+ }
}
reset_control_deassert(pcie->afi_rst);
@@ -1262,6 +1282,7 @@ static int tegra_pcie_get_resources(struct tegra_pcie *pcie)
struct device *dev = pcie->dev;
struct platform_device *pdev = to_platform_device(dev);
struct resource *pads, *afi, *res;
+ const struct tegra_pcie_soc *soc = pcie->soc;
int err;
err = tegra_pcie_clocks_get(pcie);
@@ -1276,10 +1297,12 @@ static int tegra_pcie_get_resources(struct tegra_pcie *pcie)
return err;
}
- err = tegra_pcie_phys_get(pcie);
- if (err < 0) {
- dev_err(dev, "failed to get PHYs: %d\n", err);
- return err;
+ if (soc->program_uphy) {
+ err = tegra_pcie_phys_get(pcie);
+ if (err < 0) {
+ dev_err(dev, "failed to get PHYs: %d\n", err);
+ return err;
+ }
}
err = tegra_pcie_power_on(pcie);
@@ -1616,7 +1639,31 @@ static int tegra_pcie_get_xbar_config(struct tegra_pcie *pcie, u32 lanes,
struct device *dev = pcie->dev;
struct device_node *np = dev->of_node;
- if (of_device_is_compatible(np, "nvidia,tegra124-pcie") ||
+ if (of_device_is_compatible(np, "nvidia,tegra186-pcie")) {
+ switch (lanes) {
+ case 0x010004:
+ dev_info(dev, "4x1, 1x1 configuration\n");
+ *xbar = AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_401;
+ return 0;
+
+ case 0x010102:
+ dev_info(dev, "2x1, 1X1, 1x1 configuration\n");
+ *xbar = AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_211;
+ return 0;
+
+ case 0x010101:
+ dev_info(dev, "1x1, 1x1, 1x1 configuration\n");
+ *xbar = AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_111;
+ return 0;
+
+ default:
+ dev_info(dev, "wrong configuration updated in DT, "
+ "switching to default 2x1, 1x1, 1x1 "
+ "configuration\n");
+ *xbar = AFI_PCIE_CONFIG_SM2TMS0_XBAR_CONFIG_211;
+ return 0;
+ }
+ } else if (of_device_is_compatible(np, "nvidia,tegra124-pcie") ||
of_device_is_compatible(np, "nvidia,tegra210-pcie")) {
switch (lanes) {
case 0x0000104:
@@ -1737,7 +1784,20 @@ static int tegra_pcie_get_regulators(struct tegra_pcie *pcie, u32 lane_mask)
struct device_node *np = dev->of_node;
unsigned int i = 0;
- if (of_device_is_compatible(np, "nvidia,tegra210-pcie")) {
+ if (of_device_is_compatible(np, "nvidia,tegra186-pcie")) {
+ pcie->num_supplies = 4;
+
+ pcie->supplies = devm_kcalloc(pcie->dev, pcie->num_supplies,
+ sizeof(*pcie->supplies),
+ GFP_KERNEL);
+ if (!pcie->supplies)
+ return -ENOMEM;
+
+ pcie->supplies[i++].supply = "dvdd-pex";
+ pcie->supplies[i++].supply = "hvdd-pex-pll";
+ pcie->supplies[i++].supply = "hvdd-pex";
+ pcie->supplies[i++].supply = "vddio-pexctl-aud";
+ } else if (of_device_is_compatible(np, "nvidia,tegra210-pcie")) {
pcie->num_supplies = 6;
pcie->supplies = devm_kcalloc(pcie->dev, pcie->num_supplies,
@@ -2076,6 +2136,7 @@ static const struct tegra_pcie_soc tegra20_pcie = {
.has_cml_clk = false,
.has_gen2 = false,
.force_pca_enable = false,
+ .program_uphy = true,
};
static const struct tegra_pcie_soc tegra30_pcie = {
@@ -2091,6 +2152,7 @@ static const struct tegra_pcie_soc tegra30_pcie = {
.has_cml_clk = true,
.has_gen2 = false,
.force_pca_enable = false,
+ .program_uphy = true,
};
static const struct tegra_pcie_soc tegra124_pcie = {
@@ -2105,6 +2167,7 @@ static const struct tegra_pcie_soc tegra124_pcie = {
.has_cml_clk = true,
.has_gen2 = true,
.force_pca_enable = false,
+ .program_uphy = true,
};
static const struct tegra_pcie_soc tegra210_pcie = {
@@ -2119,9 +2182,27 @@ static const struct tegra_pcie_soc tegra210_pcie = {
.has_cml_clk = true,
.has_gen2 = true,
.force_pca_enable = true,
+ .program_uphy = true,
+};
+
+static const struct tegra_pcie_soc tegra186_pcie = {
+ .num_ports = 3,
+ .msi_base_shift = 8,
+ .pads_pll_ctl = PADS_PLL_CTL_TEGRA30,
+ .tx_ref_sel = PADS_PLL_CTL_TXCLKREF_BUF_EN,
+ .pads_refclk_cfg0 = 0x80b880b8,
+ .pads_refclk_cfg1 = 0x000480b8,
+ .has_pex_clkreq_en = true,
+ .has_pex_bias_ctrl = true,
+ .has_intr_prsnt_sense = true,
+ .has_cml_clk = false,
+ .has_gen2 = true,
+ .force_pca_enable = false,
+ .program_uphy = false,
};
static const struct of_device_id tegra_pcie_of_match[] = {
+ { .compatible = "nvidia,tegra186-pcie", .data = &tegra186_pcie },
{ .compatible = "nvidia,tegra210-pcie", .data = &tegra210_pcie },
{ .compatible = "nvidia,tegra124-pcie", .data = &tegra124_pcie },
{ .compatible = "nvidia,tegra30-pcie", .data = &tegra30_pcie },
--
2.1.4
^ permalink raw reply related [flat|nested] 6+ messages in thread* [PATCH 3/4] arm64: tegra: Add PCIe node for Tegra186
2017-09-20 6:42 [PATCH 0/4] Add Tegra186 PCIe support Manikanta Maddireddy
2017-09-20 6:42 ` [PATCH 1/4] dt-bindings: pci: tegra: Document Tegra186 PCIe DT Manikanta Maddireddy
2017-09-20 6:42 ` [PATCH 2/4] PCI: tegra: Add Tegra186 PCIe support Manikanta Maddireddy
@ 2017-09-20 6:42 ` Manikanta Maddireddy
2017-09-20 6:42 ` [PATCH 4/4] arm64: tegra: Enable PCIe on Jetson TX2 Manikanta Maddireddy
2017-09-20 9:52 ` [PATCH 0/4] Add Tegra186 PCIe support Mikko Perttunen
4 siblings, 0 replies; 6+ messages in thread
From: Manikanta Maddireddy @ 2017-09-20 6:42 UTC (permalink / raw)
To: bhelgaas, thierry.reding, jonathanh
Cc: linux-tegra, linux-pci, Manikanta Maddireddy
Tegra186 has three PCIe controllers, which can be operated
in 401, 211 or 111 lane combinations. Add DT support for
PCIe controllers.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
---
arch/arm64/boot/dts/nvidia/tegra186.dtsi | 82 ++++++++++++++++++++++++++++++++
1 file changed, 82 insertions(+)
diff --git a/arch/arm64/boot/dts/nvidia/tegra186.dtsi b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
index 0b0552c9f7dd..9edf2a839e5d 100644
--- a/arch/arm64/boot/dts/nvidia/tegra186.dtsi
+++ b/arch/arm64/boot/dts/nvidia/tegra186.dtsi
@@ -443,6 +443,7 @@
shmem = <&cpu_bpmp_tx &cpu_bpmp_rx>;
#clock-cells = <1>;
#reset-cells = <1>;
+ #power-domain-cells = <1>;
bpmp_i2c: i2c {
compatible = "nvidia,tegra186-bpmp-i2c";
@@ -465,4 +466,85 @@
(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
interrupt-parent = <&gic>;
};
+
+ pcie@10003000 {
+ compatible = "nvidia,tegra186-pcie";
+ power-domains = <&bpmp TEGRA186_POWER_DOMAIN_PCX>;
+ device_type = "pci";
+ reg = <0x0 0x10003000 0x0 0x00000800 /* PADS registers */
+ 0x0 0x10003800 0x0 0x00000800 /* AFI registers */
+ 0x0 0x40000000 0x0 0x10000000>; /* configuration space */
+ reg-names = "pads", "afi", "cs";
+
+ interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>, /* controller interrupt */
+ <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; /* MSI interrupt */
+ interrupt-names = "intr", "msi";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 0 &gic GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>;
+
+ bus-range = <0x00 0xff>;
+ #address-cells = <3>;
+ #size-cells = <2>;
+
+ ranges = <0x82000000 0 0x10000000 0x0 0x10000000 0 0x00001000 /* port 0 configuration space */
+ 0x82000000 0 0x10001000 0x0 0x10001000 0 0x00001000 /* port 1 configuration space */
+ 0x82000000 0 0x10004000 0x0 0x10004000 0 0x00001000 /* port 2 configuration space */
+ 0x81000000 0 0x0 0x0 0x50000000 0 0x00010000 /* downstream I/O (64 KiB) */
+ 0x82000000 0 0x50100000 0x0 0x50100000 0 0x07F00000 /* non-prefetchable memory (127 MiB) */
+ 0xc2000000 0 0x58000000 0x0 0x58000000 0 0x28000000>; /* prefetchable memory (640 MiB) */
+
+ clocks = <&bpmp TEGRA186_CLK_AFI>,
+ <&bpmp TEGRA186_CLK_PCIE>,
+ <&bpmp TEGRA186_CLK_PLLE>;
+ clock-names = "afi", "pex", "pll_e";
+
+ resets = <&bpmp TEGRA186_RESET_AFI>,
+ <&bpmp TEGRA186_RESET_PCIE>,
+ <&bpmp TEGRA186_RESET_PCIEXCLK>;
+ reset-names = "afi", "pex", "pcie_x";
+
+ status = "disabled";
+
+ pci@1,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82000800 0 0x10000000 0 0x1000>;
+ reg = <0x000800 0 0 0 0>;
+ status = "disabled";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ nvidia,num-lanes = <2>;
+ };
+
+ pci@2,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001000 0 0x10001000 0 0x1000>;
+ reg = <0x001000 0 0 0 0>;
+ status = "disabled";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ nvidia,num-lanes = <1>;
+ };
+
+ pci@3,0 {
+ device_type = "pci";
+ assigned-addresses = <0x82001800 0 0x10004000 0 0x1000>;
+ reg = <0x001800 0 0 0 0>;
+ status = "disabled";
+
+ #address-cells = <3>;
+ #size-cells = <2>;
+ ranges;
+
+ nvidia,num-lanes = <1>;
+ };
+
+ };
};
--
2.1.4
^ permalink raw reply related [flat|nested] 6+ messages in thread