linux-pci.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
To: Marek Vasut <marek.vasut@gmail.com>
Cc: linux-pci@vger.kernel.org,
	Marek Vasut <marek.vasut+renesas@gmail.com>,
	Geert Uytterhoeven <geert+renesas@glider.be>,
	Phil Edworthy <phil.edworthy@renesas.com>,
	Simon Horman <horms+renesas@verge.net.au>,
	Wolfram Sang <wsa@the-dreams.de>,
	linux-renesas-soc@vger.kernel.org
Subject: Re: [PATCH v4 6/6] PCI: rcar: Shut the PHY down in failpath
Date: Fri, 29 Jun 2018 14:38:05 +0100	[thread overview]
Message-ID: <20180629133805.GA9643@red-moon> (raw)
In-Reply-To: <20180524143624.26718-7-marek.vasut+renesas@gmail.com>

On Thu, May 24, 2018 at 04:36:24PM +0200, Marek Vasut wrote:
> If anything fails past phy_init_fn() and the system is a Gen3 with
> a PHY, the PHY will be left on and inited. This is caused by the
> phy_init_fn, which is in fact a pointer to rcar_pcie_phy_init_gen3()
> function, which starts the PHY, yet has no counterpart in the failpath.
> Add that counterpart.
> 
> Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
> Cc: Geert Uytterhoeven <geert+renesas@glider.be>
> Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
> Cc: Phil Edworthy <phil.edworthy@renesas.com>
> Cc: Simon Horman <horms+renesas@verge.net.au>
> Cc: Wolfram Sang <wsa@the-dreams.de>
> Cc: linux-renesas-soc@vger.kernel.org
> Fixes: 517ca93a7159 ("PCI: rcar: Add R-Car gen3 PHY support")
> ---
> V4: New patch
> ---
>  drivers/pci/host/pcie-rcar.c | 10 ++++++++--
>  1 file changed, 8 insertions(+), 2 deletions(-)

Applied to pci/controller-fixes to be tentatively merged at -rc4,
thanks.

Lorenzo

> diff --git a/drivers/pci/host/pcie-rcar.c b/drivers/pci/host/pcie-rcar.c
> index 636c3c5095d2..695781934f0a 100644
> --- a/drivers/pci/host/pcie-rcar.c
> +++ b/drivers/pci/host/pcie-rcar.c
> @@ -1163,7 +1163,7 @@ static int rcar_pcie_probe(struct platform_device *pdev)
>  	if (rcar_pcie_hw_init(pcie)) {
>  		dev_info(dev, "PCIe link down\n");
>  		err = -ENODEV;
> -		goto err_clk_disable;
> +		goto err_phy_shutdown;
>  	}
>  
>  	data = rcar_pci_read_reg(pcie, MACSR);
> @@ -1175,7 +1175,7 @@ static int rcar_pcie_probe(struct platform_device *pdev)
>  			dev_err(dev,
>  				"failed to enable MSI support: %d\n",
>  				err);
> -			goto err_clk_disable;
> +			goto err_phy_shutdown;
>  		}
>  	}
>  
> @@ -1189,6 +1189,12 @@ static int rcar_pcie_probe(struct platform_device *pdev)
>  	if (IS_ENABLED(CONFIG_PCI_MSI))
>  		rcar_pcie_teardown_msi(pcie);
>  
> +err_phy_shutdown:
> +	if (pcie->phy) {
> +		phy_power_off(pcie->phy);
> +		phy_exit(pcie->phy);
> +	}
> +
>  err_clk_disable:
>  	clk_disable_unprepare(pcie->bus_clk);
>  
> -- 
> 2.16.2
> 

  parent reply	other threads:[~2018-06-29 13:36 UTC|newest]

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-05-24 14:36 [PATCH v4 0/6] PCI: rcar: Failpath fixes Marek Vasut
2018-05-24 14:36 ` [PATCH v4 1/6] PCI: rcar: Pull bus clock enable/disable from rcar_pcie_get_resources() Marek Vasut
2018-05-28  8:51   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 2/6] PCI: rcar: Add missing irq_dispose_mapping() into failpath Marek Vasut
2018-05-28  8:51   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 3/6] PCI: rcar: Teardown MSI setup if rcar_pcie_enable() fails Marek Vasut
2018-05-28  8:52   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 4/6] PCI: rcar: Poll more often in rcar_pcie_wait_for_dl() Marek Vasut
2018-05-28  8:53   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 5/6] PCI: rcar: Remove IRQ mappings in rcar_pcie_enable_msi failpath Marek Vasut
2018-05-28  8:53   ` Simon Horman
2018-05-24 14:36 ` [PATCH v4 6/6] PCI: rcar: Shut the PHY down in failpath Marek Vasut
2018-05-25 10:09   ` Geert Uytterhoeven
2018-05-25 18:34     ` Marek Vasut
2018-05-28  8:48   ` Simon Horman
2018-06-01 23:30     ` Marek Vasut
2018-06-29 13:38   ` Lorenzo Pieralisi [this message]
2018-05-25  9:35 ` [PATCH v4 0/6] PCI: rcar: Failpath fixes Lorenzo Pieralisi
2018-05-25  9:39   ` Geert Uytterhoeven
2018-05-25  9:56     ` Lorenzo Pieralisi
2018-05-25 10:01       ` Geert Uytterhoeven
2018-05-25 16:43 ` Lorenzo Pieralisi
2018-05-25 17:10   ` Marek Vasut
2018-05-28  8:54   ` Simon Horman

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20180629133805.GA9643@red-moon \
    --to=lorenzo.pieralisi@arm.com \
    --cc=geert+renesas@glider.be \
    --cc=horms+renesas@verge.net.au \
    --cc=linux-pci@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=marek.vasut+renesas@gmail.com \
    --cc=marek.vasut@gmail.com \
    --cc=phil.edworthy@renesas.com \
    --cc=wsa@the-dreams.de \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).