From: Christoph Hellwig <hch@infradead.org>
To: Daire McNamara <daire.mcnamara@microchip.com>
Cc: linux-pci@vger.kernel.org, devicetree@vger.kernel.org,
Arnd Bergmann <arnd@arndb.de>
Subject: Re: [PATCH v3 3/3] PCI: microsemi: Add host driver for Microsemi PCIe controller
Date: Sat, 16 Feb 2019 00:04:15 -0800 [thread overview]
Message-ID: <20190216080415.GA6506@infradead.org> (raw)
In-Reply-To: <20190215162424.564-4-daire.mcnamara@microchip.com>
On Fri, Feb 15, 2019 at 04:24:24PM +0000, Daire McNamara wrote:
> This patch adds support to the Microsemi/Microchip PolarFire
> PCIe controller when configured in host (Root Complex) mode.
This doesn't seem to address most of the comments in:
http://lists.infradead.org/pipermail/linux-riscv/2018-August/001058.html
or
http://lists.infradead.org/pipermail/linux-riscv/2018-August/001073.html
>
> Signed-off-by: Daire McNamara <daire.mcnamara@microchip.com>
> ---
> drivers/pci/controller/Kconfig | 8 +
> drivers/pci/controller/Makefile | 1 +
> drivers/pci/controller/pcie-microsemi.c | 764 ++++++++++++++++++++++++
> 3 files changed, 773 insertions(+)
> create mode 100644 drivers/pci/controller/pcie-microsemi.c
>
> diff --git a/drivers/pci/controller/Kconfig b/drivers/pci/controller/Kconfig
> index 6671946dbf66..31fa5e53d765 100644
> --- a/drivers/pci/controller/Kconfig
> +++ b/drivers/pci/controller/Kconfig
> @@ -280,5 +280,13 @@ config VMD
> To compile this driver as a module, choose M here: the
> module will be called vmd.
>
> +config PCIE_MICROSEMI
> + bool "Microsemi AXI PCIe host bridge support"
> + depends on PCI_MSI && OF
> + help
> + Say 'Y' here if you want kernel to support the Microsemi AXI PCIe
> + Host Bridge driver.
> +
> +
> source "drivers/pci/controller/dwc/Kconfig"
> endmenu
> diff --git a/drivers/pci/controller/Makefile b/drivers/pci/controller/Makefile
> index d56a507495c5..c3b76ff221be 100644
> --- a/drivers/pci/controller/Makefile
> +++ b/drivers/pci/controller/Makefile
> @@ -28,6 +28,7 @@ obj-$(CONFIG_PCIE_ROCKCHIP_HOST) += pcie-rockchip-host.o
> obj-$(CONFIG_PCIE_MEDIATEK) += pcie-mediatek.o
> obj-$(CONFIG_PCIE_MOBIVEIL) += pcie-mobiveil.o
> obj-$(CONFIG_PCIE_TANGO_SMP8759) += pcie-tango.o
> +obj-$(CONFIG_PCIE_MICROSEMI) += pcie-microsemi.o
> obj-$(CONFIG_VMD) += vmd.o
> # pcie-hisi.o quirks are needed even without CONFIG_PCIE_DW
> obj-y += dwc/
> diff --git a/drivers/pci/controller/pcie-microsemi.c b/drivers/pci/controller/pcie-microsemi.c
> new file mode 100644
> index 000000000000..60e185bebc60
> --- /dev/null
> +++ b/drivers/pci/controller/pcie-microsemi.c
> @@ -0,0 +1,764 @@
> +// SPDX-License-Identifier: GPL-2.0+
> +/*
> + * PCIe host controller driver for Microsemi AXI PCIe Bridge
> + *
> + * Copyright (c) 2018 - 2019 Microsemi Corporation.
> + *
> + * Based on:
> + * pcie-rcar.c
> + * pcie-xilinx.c
> + * pcie-altera.c
> + */
> +
> +#include <linux/bitmap.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
> +#include <linux/irqdomain.h>
> +#include <linux/kernel.h>
> +#include <linux/init.h>
> +#include <linux/msi.h>
> +#include <linux/of_address.h>
> +#include <linux/of_pci.h>
> +#include <linux/of_platform.h>
> +#include <linux/of_irq.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +
> +#include "../pci.h"
> +
> +/* ECAM definitions */
> +#define ECAM_BUS_NUM_SHIFT 20
> +#define ECAM_DEV_NUM_SHIFT 12
> +
> +/* Number of MSI IRQs */
> +#define MICROSEMI_NUM_MSI_IRQS 32
> +#define MICROSEMI_NUM_MSI_IRQS_CODED 5
> +
> +/* PCIe Bridge Phy and Controller Phy offsets */
> +#define MICROSEMI_PCIE0_BRIDGE_ADDR 0x00004000u
> +#define MICROSEMI_PCIE0_CTRL_ADDR 0x00006000u
> +
> +#define MICROSEMI_PCIE1_BRIDGE_ADDR 0x00008000u
> +#define MICROSEMI_PCIE1_CTRL_ADDR 0x0000a000u
> +
> +/* PCIe Controller Phy Regs */
> +#define MICROSEMI_SEC_ERROR_INT 0x28
> +#define SEC_ERROR_INT_TX_RAM_SEC_ERR_INT GENMASK(3, 0)
> +#define SEC_ERROR_INT_RX_RAM_SEC_ERR_INT GENMASK(7, 4)
> +#define SEC_ERROR_INT_PCIE2AXI_RAM_SEC_ERR_INT GENMASK(11, 8)
> +#define SEC_ERROR_INT_AXI2PCIE_RAM_SEC_ERR_INT GENMASK(15, 12)
> +#define MICROSEMI_SEC_ERROR_INT_MASK 0x2c
> +#define MICROSEMI_DED_ERROR_INT 0x30
> +#define DED_ERROR_INT_TX_RAM_DED_ERR_INT GENMASK(3, 0)
> +#define DED_ERROR_INT_RX_RAM_DED_ERR_INT GENMASK(7, 4)
> +#define DED_ERROR_INT_PCIE2AXI_RAM_DED_ERR_INT GENMASK(11, 8)
> +#define DED_ERROR_INT_AXI2PCIE_RAM_DED_ERR_INT GENMASK(15, 12)
> +#define MICROSEMI_DED_ERROR_INT_MASK 0x34
> +#define MICROSEMI_ECC_CONTROL 0x38
> +#define ECC_CONTROL_AXI2PCIE_RAM_ECC_BYPASS BIT(27)
> +#define ECC_CONTROL_PCIE2AXI_RAM_ECC_BYPASS BIT(26)
> +#define ECC_CONTROL_RX_RAM_ECC_BYPASS BIT(25)
> +#define ECC_CONTROL_TX_RAM_ECC_BYPASS BIT(24)
> +#define MICROSEMI_LTSSM_STATE 0x5c
> +#define MICROSEMI_LTSSM_L0_STATE 0x10
> +#define MICROSEMI_PCIE_EVENT_INT 0x14c
> +#define PCIE_EVENT_INT_L2_EXIT_INT BIT(0)
> +#define PCIE_EVENT_INT_HOTRST_EXIT_INT BIT(1)
> +#define PCIE_EVENT_INT_DLUP_EXIT_INT BIT(2)
> +#define PCIE_EVENT_INT_L2_EXIT_INT_MASK BIT(16)
> +#define PCIE_EVENT_INT_HOTRST_EXIT_INT_MASK BIT(17)
> +#define PCIE_EVENT_INT_DLUP_EXIT_INT_MASK BIT(18)
> +
> +/* PCIe Bridge Phy Regs */
> +#define MICROSEMI_PCIE_PCI_IDS_DW1 0x9c
> +#define MICROSEMI_IMASK_LOCAL 0x180
> +#define MICROSEMI_PCIE_LOCAL_INT_ENABLE 0x0f000000u
> +#define MICROSEMI_PCI_INTS 0x0f000000u
> +#define MICROSEMI_PM_MSI_INT_SHIFT 24
> +#define MICROSEMI_PCIE_ENABLE_MSI 0x10000000u
> +#define MICROSEMI_MSI_INT 0x10000000u
> +#define MICROSEMI_MSI_INT_SHIFT 28
> +#define MICROSEMI_ISTATUS_LOCAL 0x184
> +#define MICROSEMI_IMASK_HOST 0x188
> +#define MICROSEMI_ISTATUS_HOST 0x18c
> +#define MICROSEMI_ISTATUS_MSI 0x194
> +
> +/* PCIe AXI slave table init defines */
> +#define MICROSEMI_ATR0_AXI4_SLV0_SRCADDR_PARAM 0x800u
> +#define ATR_SIZE_SHIFT 1
> +#define ATR_IMPL_ENABLE 1
> +#define MICROSEMI_ATR0_AXI4_SLV0_SRC_ADDR 0x804u
> +#define MICROSEMI_ATR0_AXI4_SLV0_TRSL_ADDR_LSB 0x808u
> +#define MICROSEMI_ATR0_AXI4_SLV0_TRSL_ADDR_UDW 0x80cu
> +#define MICROSEMI_ATR0_AXI4_SLV0_TRSL_PARAM 0x810u
> +#define MICROSEMI_PCIE_TX_RX_INTERFACE 0x00000000u
> +#define MICROSEMI_PCIE_CONFIG_INTERFACE 0x00000001u
> +
> +#define MICROSEMI_ATR0_AXI4_SLV_SIZE 32
> +
> +/* PCIe Master table init defines */
> +#define MICROSEMI_ATR0_PCIE_WIN0_SRCADDR_31_12 0x600u
> +#define MICROSEMI_ATR0_PCIE_WIN0_SIZE 0x1f
> +#define MICROSEMI_ATR0_PCIE_WIN0_SIZE_SHIFT 1
> +#define MICROSEMI_ATR0_PCIE_WIN0_SRCADDR_63_32 0x604u
> +
> +#define MICROSEMI_MSI_MSG_ADDR 0x190u
> +
> +/* PCIe Config space MSI capability structure */
> +#define MSI_CAP_CTRL_OFFSET 0xe0u
> +#define MSI_ENABLE (0x01u << 16)
> +#define MSI_ENABLE_MULTI (MICROSEMI_NUM_MSI_IRQS_CODED << 20)
> +#define MSI_MSG_ADDR_OFFSET 0xe4u
> +#define MSI_MSG_UPPER_ADDR_OFFSET 0xe8u
> +#define MSI_MSG_DATA_OFFSET 0xf0u
> +
> +/**
> + * struct microsemi_pcie_port - PCIe port information
> + * @pcie_base_addr: IO Mapped Register Base
> + * @axi_base_addr: AMBA Mapped Register Base
> + * @irq: Interrupt number
> + * @root_busno: Root Bus number
> + * @dev: Device pointer
> + * @msi_domain: MSI IRQ domain pointer
> + * @leg_domain: Legacy IRQ domain pointer
> + * @resources: Bus Resources
> + */
> +struct microsemi_pcie_port {
> + struct platform_device *pdev;
> + void __iomem *pcie_base_addr;
> + void __iomem *axi_base_addr;
> + void __iomem *bridge_base_addr;
> + void __iomem *ctrl_base_addr;
> + int bridge;
> + u32 irq;
> + u8 root_busno;
> + struct device *dev;
> + struct irq_domain *msi_domain;
> + struct irq_domain *leg_domain;
> + struct list_head resources;
> + struct mutex lock; /* protect bitmap variable */
> + DECLARE_BITMAP(msi_irq_in_use, MICROSEMI_NUM_MSI_IRQS);
> +};
> +
> +static inline u32 pcie_read(struct microsemi_pcie_port *port, u32 reg)
> +{
> + return readl(port->pcie_base_addr + reg);
> +}
> +
> +static inline void pcie_write(struct microsemi_pcie_port *port,
> + u32 val, u32 reg)
> +{
> + writel(val, port->pcie_base_addr + reg);
> +}
> +
> +static void microsemi_pcie_enable(struct microsemi_pcie_port *port)
> +{
> + u32 enb;
> +
> + enb = readl(port->bridge_base_addr + MICROSEMI_LTSSM_STATE);
> + enb |= MICROSEMI_LTSSM_L0_STATE;
> + writel(enb, port->bridge_base_addr + MICROSEMI_LTSSM_STATE);
> +}
> +
> +/**
> + * microsemi_pcie_valid_device - Check if a valid device is present on bus
> + * @bus: PCI Bus structure
> + * @devfn: device/function
> + *
> + * Return: 'true' on success and 'false' if invalid device is found
> + */
> +static bool microsemi_pcie_valid_device(struct pci_bus *bus, unsigned int devfn)
> +{
> + struct microsemi_pcie_port *port = bus->sysdata;
> +
> + /* Only one device down on each root port */
> + if (bus->number == port->root_busno && devfn > 0)
> + return false;
> +
> + return true;
> +}
> +
> +/**
> + * microsemi_pcie_map_bus - Get configuration base
> + * @bus: PCI Bus structure
> + * @devfn: Device/function
> + * @where: Offset from base
> + *
> + * Return: Base address of the configuration space needed to be
> + * accessed.
> + */
> +static void __iomem *microsemi_pcie_map_bus(struct pci_bus *bus,
> + unsigned int devfn, int where)
> +{
> + struct microsemi_pcie_port *port = bus->sysdata;
> + int relbus;
> +
> + if (!microsemi_pcie_valid_device(bus, devfn))
> + return NULL;
> +
> + relbus = (bus->number << ECAM_BUS_NUM_SHIFT) |
> + (devfn << ECAM_DEV_NUM_SHIFT);
> +
> + return port->pcie_base_addr + relbus + where;
> +}
> +
> +/* PCIe operations */
> +static struct pci_ops microsemi_pcie_ops = {
> + .map_bus = microsemi_pcie_map_bus,
> + .read = pci_generic_config_read,
> + .write = pci_generic_config_write,
> +};
> +
> +/* MSI functions */
> +
> +/**
> + * microsemi_pcie_destroy_msi - Free MSI number
> + * @irq: IRQ to be freed
> + */
> +static void microsemi_pcie_destroy_msi(unsigned int irq)
> +{
> + struct microsemi_pcie_port *port =
> + msi_desc_to_pci_sysdata(irq_get_msi_desc(irq));
> + irq_hw_number_t hwirq = irqd_to_hwirq(irq_get_irq_data(irq));
> +
> + if (!port)
> + return;
> +
> + if (!test_bit(hwirq, port->msi_irq_in_use))
> + dev_err(port->dev, "trying to free unused MSI%d\n", irq);
> + else
> + clear_bit(hwirq, port->msi_irq_in_use);
> +}
> +
> +/**
> + * microsemi_pcie_assign_msi - Allocate MSI number
> + *
> + * Return: A valid IRQ on success and error value on failure.
> + */
> +static int microsemi_pcie_assign_msi(struct microsemi_pcie_port *port)
> +{
> + int pos;
> +
> + mutex_lock(&port->lock);
> + pos = find_first_zero_bit(port->msi_irq_in_use, MICROSEMI_NUM_MSI_IRQS);
> + if (pos < MICROSEMI_NUM_MSI_IRQS) {
> + set_bit(pos, port->msi_irq_in_use);
> + } else {
> + mutex_unlock(&port->lock);
> + return -ENOSPC;
> + }
> +
> + mutex_unlock(&port->lock);
> + return pos;
> +}
> +
> +/**
> + * microsemi_msi_teardown_irq - Destroy the MSI
> + * @chip: MSI Chip descriptor
> + * @irq: MSI IRQ to destroy
> + */
> +static void microsemi_msi_teardown_irq(struct msi_controller *chip,
> + unsigned int irq)
> +{
> + microsemi_pcie_destroy_msi(irq);
> + irq_dispose_mapping(irq);
> +}
> +
> +/**
> + * microsemi_pcie_msi_setup_irq - Setup MSI request
> + * @chip: MSI chip pointer
> + * @pdev: PCIe device pointer
> + * @desc: MSI descriptor pointer
> + *
> + * Return: '0' on success and error value on failure
> + */
> +static int microsemi_pcie_msi_setup_irq(struct msi_controller *chip,
> + struct pci_dev *pdev,
> + struct msi_desc *desc)
> +{
> + struct microsemi_pcie_port *port = pdev->bus->sysdata;
> + unsigned int irq;
> + int hwirq;
> + struct msi_msg msg;
> +
> + hwirq = microsemi_pcie_assign_msi(port);
> + if (hwirq < 0)
> + return hwirq;
> +
> + irq = irq_create_mapping(port->msi_domain, hwirq);
> + if (!irq)
> + return -EINVAL;
> +
> + irq_set_msi_desc(irq, desc);
> +
> + msg.address_hi = upper_32_bits(MICROSEMI_MSI_MSG_ADDR);
> + msg.address_lo = lower_32_bits(MICROSEMI_MSI_MSG_ADDR);
> + msg.data = hwirq;
> +
> + pci_write_msi_msg(irq, &msg);
> +
> + return 0;
> +}
> +
> +/* MSI Chip Descriptor */
> +static struct msi_controller microsemi_pcie_msi_chip = {
> + .setup_irq = microsemi_pcie_msi_setup_irq,
> + .teardown_irq = microsemi_msi_teardown_irq,
> +};
> +
> +/* HW Interrupt Chip Descriptor */
> +static struct irq_chip microsemi_msi_irq_chip = {
> + .name = "Microsemi PCIe MSI",
> + .irq_enable = pci_msi_unmask_irq,
> + .irq_disable = pci_msi_mask_irq,
> + .irq_mask = pci_msi_mask_irq,
> + .irq_unmask = pci_msi_unmask_irq,
> +};
> +
> +/**
> + * microsemi_pcie_msi_map - Set the handler for the MSI and mark IRQ as valid
> + * @domain: IRQ domain
> + * @irq: Virtual IRQ number
> + * @hwirq: HW interrupt number
> + *
> + * Return: Always returns 0.
> + */
> +static int microsemi_pcie_msi_map(struct irq_domain *domain, unsigned int irq,
> + irq_hw_number_t hwirq)
> +{
> + irq_set_chip_and_handler(irq, µsemi_msi_irq_chip,
> + handle_simple_irq);
> + irq_set_chip_data(irq, domain->host_data);
> +
> + return 0;
> +}
> +
> +/* IRQ Domain operations */
> +static const struct irq_domain_ops msi_domain_ops = {
> + .map = microsemi_pcie_msi_map,
> +};
> +
> +/**
> + * microsemi_pcie_enable_msi - Enable MSI support
> + * @port: PCIe port information
> + */
> +static void microsemi_pcie_enable_msi(struct microsemi_pcie_port *port)
> +{
> + u32 cap_ctrl;
> +
> + cap_ctrl = pcie_read(port, MSI_CAP_CTRL_OFFSET);
> +
> + pcie_write(port, cap_ctrl | MSI_ENABLE_MULTI |
> + MSI_ENABLE, MSI_CAP_CTRL_OFFSET);
> + pcie_write(port, MICROSEMI_MSI_MSG_ADDR, MSI_MSG_ADDR_OFFSET);
> +}
> +
> +/* INTx Functions */
> +
> +/**
> + * microsemi_pcie_intx_map - Set the handler for the INTx and mark IRQ as valid
> + * @domain: IRQ domain
> + * @irq: Virtual IRQ number
> + * @hwirq: HW interrupt number
> + *
> + * Return: Always returns 0.
> + */
> +static int microsemi_pcie_intx_map(struct irq_domain *domain, unsigned int irq,
> + irq_hw_number_t hwirq)
> +{
> + irq_set_chip_and_handler(irq, &dummy_irq_chip, handle_simple_irq);
> + irq_set_chip_data(irq, domain->host_data);
> +
> + return 0;
> +}
> +
> +/* INTx IRQ Domain operations */
> +static const struct irq_domain_ops intx_domain_ops = {
> + .map = microsemi_pcie_intx_map,
> + .xlate = pci_irqd_intx_xlate,
> +};
> +
> +/* PCIe HW Functions */
> +
> +/**
> + * microsemi_pcie_intr_handler - Interrupt Service Handler
> + * @irq: IRQ number
> + * @data: PCIe port information
> + *
> + * Return: IRQ_HANDLED on success and IRQ_NONE on failure
> + */
> +static irqreturn_t microsemi_pcie_intr_handler(int irq, void *data)
> +{
> + struct microsemi_pcie_port *port = (struct microsemi_pcie_port *)data;
> + struct device *dev = port->dev;
> + unsigned long status;
> + unsigned long msi;
> + u32 bit;
> + u32 virq;
> +
> + status = readl(port->bridge_base_addr + MICROSEMI_ISTATUS_LOCAL);
> +
> + /* Might be sharing interrupt line. Check if interrupt is for us */
> + if (!status)
> + return IRQ_NONE;
> +
> + status = (status & MICROSEMI_PCI_INTS) >> MICROSEMI_PM_MSI_INT_SHIFT;
> + for_each_set_bit(bit, &status, PCI_NUM_INTX) {
> + /* clear that interrupt bit */
> + writel(1 << (bit + MICROSEMI_PM_MSI_INT_SHIFT),
> + port->bridge_base_addr + MICROSEMI_ISTATUS_LOCAL);
> + virq = irq_find_mapping(port->leg_domain, bit);
> +
> + if (virq)
> + generic_handle_irq(virq);
> + else
> + dev_err(dev, "unexpected IRQ, INT%d\n", bit);
> + }
> +
> + status = readl(port->bridge_base_addr + MICROSEMI_ISTATUS_LOCAL);
> + if (status & MICROSEMI_MSI_INT) {
> + /* Clear the ISTATUS MSI bit */
> + writel((1 << MICROSEMI_MSI_INT_SHIFT),
> + port->bridge_base_addr + MICROSEMI_ISTATUS_LOCAL);
> + msi = readl(port->bridge_base_addr + MICROSEMI_ISTATUS_MSI);
> + for_each_set_bit(bit, &msi, MICROSEMI_NUM_MSI_IRQS) {
> + /* clear that MSI interrupt bit */
> + writel((1 << bit),
> + port->bridge_base_addr + MICROSEMI_ISTATUS_MSI);
> + virq = irq_find_mapping(port->msi_domain, bit);
> + if (virq)
> + generic_handle_irq(virq);
> + else
> + dev_err(dev, "unexpected IRQ, INT%d\n", bit);
> + }
> + }
> +
> + return IRQ_HANDLED;
> +}
> +
> +/**
> + * microsemi_pcie_init_irq_domain - Initialize IRQ domain
> + * @port: PCIe port information
> + *
> + * Return: '0' on success and error value on failure
> + */
> +static int microsemi_pcie_init_irq_domain(struct microsemi_pcie_port *port)
> +{
> + struct device *dev = port->dev;
> + struct device_node *node = dev->of_node;
> + struct device_node *pcie_intc_node;
> +
> + /* Setup INTx */
> + pcie_intc_node = of_get_next_child(node, NULL);
> + if (!pcie_intc_node) {
> + dev_err(dev, "no PCIe INTx node found\n");
> + return -ENODEV;
> + }
> +
> + port->leg_domain = irq_domain_add_linear(pcie_intc_node, PCI_NUM_INTX,
> + &intx_domain_ops,
> + port);
> + if (!port->leg_domain) {
> + dev_err(dev, "failed to get a INTx IRQ domain\n");
> + return -ENODEV;
> + }
> +
> + /* Setup MSI */
> + if (IS_ENABLED(CONFIG_PCI_MSI)) {
> + port->msi_domain =
> + irq_domain_add_linear(node,
> + MICROSEMI_NUM_MSI_IRQS,
> + &msi_domain_ops,
> + µsemi_pcie_msi_chip);
> + if (!port->msi_domain) {
> + dev_err(dev, "failed to get an MSI IRQ domain\n");
> + return -ENODEV;
> + }
> + microsemi_pcie_enable_msi(port);
> + }
> +
> + /* Enable interrupts */
> + writel(MICROSEMI_PCIE_ENABLE_MSI | MICROSEMI_PCIE_LOCAL_INT_ENABLE,
> + port->bridge_base_addr + MICROSEMI_IMASK_LOCAL);
> +
> + return 0;
> +}
> +
> +/**
> + * microsemi_pcie_init_port - Parse Device tree, Initialize hardware
> + * @port: PCIe port information
> + *
> + * Return: '0' on success and error value on failure
> + */
> +static int microsemi_pcie_init_port(struct microsemi_pcie_port *port)
> +{
> + struct device *dev = port->dev;
> + struct device_node *node = dev->of_node;
> + struct of_pci_range_parser parser;
> + struct of_pci_range range;
> + struct resource regs;
> + struct resource regs1;
> + resource_size_t size;
> + u32 atr_sz;
> + const char *type;
> + int err;
> + u32 val;
> + int index = 1;
> +
> + type = of_get_property(node, "device_type", NULL);
> + if (!type || strcmp(type, "pci")) {
> + dev_err(dev, "invalid \"device_type\" %s\n", type);
> + return -EINVAL;
> + }
> +
> + /* Only supporting bridge 1 */
> + port->bridge = 1;
> +
> + mutex_init(&port->lock);
> +
> + err = of_address_to_resource(node, 0, ®s);
> + if (err) {
> + dev_err(dev, "missing \"reg\" property\n");
> + return err;
> + }
> +
> + port->pcie_base_addr = devm_pci_remap_cfg_resource(dev, ®s);
> + if (IS_ERR(port->pcie_base_addr))
> + return PTR_ERR(port->pcie_base_addr);
> +
> + err = of_address_to_resource(node, 1, ®s1);
> + if (err) {
> + dev_err(dev, "missing \"reg\" property\n");
> + return err;
> + }
> +
> + port->axi_base_addr = devm_ioremap_resource(dev, ®s1);
> + if (IS_ERR(port->axi_base_addr))
> + return PTR_ERR(port->axi_base_addr);
> +
> + if (port->bridge == 0) {
> + port->bridge_base_addr = port->axi_base_addr
> + + MICROSEMI_PCIE0_BRIDGE_ADDR;
> + port->ctrl_base_addr = port->axi_base_addr
> + + MICROSEMI_PCIE0_CTRL_ADDR;
> + } else {
> + port->bridge_base_addr = port->axi_base_addr
> + + MICROSEMI_PCIE1_BRIDGE_ADDR;
> + port->ctrl_base_addr = port->axi_base_addr
> + + MICROSEMI_PCIE1_CTRL_ADDR;
> + }
> +
> + port->irq = irq_of_parse_and_map(node, 0);
> +
> + err = devm_request_irq(dev, port->irq, microsemi_pcie_intr_handler,
> + IRQF_SHARED | IRQF_NO_THREAD,
> + "microsemi-pcie", port);
> + if (err) {
> + dev_err(dev, "unable to request IRQ%d\n", port->irq);
> + return err;
> + }
> +
> + microsemi_pcie_enable(port);
> +
> + /* Clear and Disable interrupts */
> + val = ECC_CONTROL_AXI2PCIE_RAM_ECC_BYPASS
> + | ECC_CONTROL_PCIE2AXI_RAM_ECC_BYPASS
> + | ECC_CONTROL_RX_RAM_ECC_BYPASS
> + | ECC_CONTROL_TX_RAM_ECC_BYPASS;
> + writel(val, port->ctrl_base_addr + MICROSEMI_ECC_CONTROL);
> +
> + val = PCIE_EVENT_INT_L2_EXIT_INT
> + | PCIE_EVENT_INT_HOTRST_EXIT_INT
> + | PCIE_EVENT_INT_DLUP_EXIT_INT
> + | PCIE_EVENT_INT_L2_EXIT_INT_MASK
> + | PCIE_EVENT_INT_HOTRST_EXIT_INT_MASK
> + | PCIE_EVENT_INT_DLUP_EXIT_INT_MASK;
> + writel(val, port->ctrl_base_addr + MICROSEMI_PCIE_EVENT_INT);
> +
> + val = SEC_ERROR_INT_TX_RAM_SEC_ERR_INT
> + | SEC_ERROR_INT_RX_RAM_SEC_ERR_INT
> + | SEC_ERROR_INT_PCIE2AXI_RAM_SEC_ERR_INT
> + | SEC_ERROR_INT_AXI2PCIE_RAM_SEC_ERR_INT;
> + writel(val, port->ctrl_base_addr + MICROSEMI_SEC_ERROR_INT);
> + writel(val, port->ctrl_base_addr + MICROSEMI_SEC_ERROR_INT_MASK);
> +
> + val = DED_ERROR_INT_TX_RAM_DED_ERR_INT
> + | DED_ERROR_INT_RX_RAM_DED_ERR_INT
> + | DED_ERROR_INT_PCIE2AXI_RAM_DED_ERR_INT
> + | DED_ERROR_INT_AXI2PCIE_RAM_DED_ERR_INT;
> + writel(val, port->ctrl_base_addr + MICROSEMI_DED_ERROR_INT);
> + writel(val, port->ctrl_base_addr + MICROSEMI_DED_ERROR_INT_MASK);
> +
> + writel(0x00000000, port->bridge_base_addr + MICROSEMI_IMASK_LOCAL);
> + writel(GENMASK(31, 0),
> + port->bridge_base_addr + MICROSEMI_ISTATUS_LOCAL);
> + writel(0x00000000, port->bridge_base_addr + MICROSEMI_IMASK_HOST);
> + writel(GENMASK(31, 0), port->bridge_base_addr + MICROSEMI_ISTATUS_HOST);
> +
> + /* Configure Address Translation Table 0 for PCIe config space */
> + writel(MICROSEMI_PCIE_CONFIG_INTERFACE,
> + port->bridge_base_addr + MICROSEMI_ATR0_AXI4_SLV0_TRSL_PARAM);
> +
> + size = resource_size(®s);
> +
> + atr_sz = find_first_bit((const unsigned long *)&size, 64) - 1;
> +
> + writel(lower_32_bits(regs.start)
> + | atr_sz << ATR_SIZE_SHIFT | ATR_IMPL_ENABLE,
> + port->bridge_base_addr
> + + MICROSEMI_ATR0_AXI4_SLV0_SRCADDR_PARAM);
> +
> + writel(lower_32_bits(regs.start),
> + port->bridge_base_addr + MICROSEMI_ATR0_AXI4_SLV0_TRSL_ADDR_LSB);
> +
> + if (of_pci_range_parser_init(&parser, node)) {
> + dev_err(dev, "missing \"ranges\" property\n");
> + return -EINVAL;
> + }
> +
> + for_each_of_pci_range(&parser, &range) {
> + switch (range.flags & IORESOURCE_TYPE_BITS) {
> + case IORESOURCE_MEM:
> + size = range.size;
> + atr_sz =
> + find_first_bit((const unsigned long *)&size, 64)
> + - 1;
> +
> + /* Configure Address Translation Table index for PCIe
> + * mem space
> + */
> + writel(MICROSEMI_PCIE_TX_RX_INTERFACE,
> + port->bridge_base_addr
> + + (index * MICROSEMI_ATR0_AXI4_SLV_SIZE)
> + + MICROSEMI_ATR0_AXI4_SLV0_TRSL_PARAM);
> +
> + writel(lower_32_bits(range.cpu_addr)
> + | (atr_sz << ATR_SIZE_SHIFT)
> + | ATR_IMPL_ENABLE,
> + port->bridge_base_addr
> + + (index * MICROSEMI_ATR0_AXI4_SLV_SIZE)
> + + MICROSEMI_ATR0_AXI4_SLV0_SRCADDR_PARAM);
> +
> + writel(lower_32_bits(range.pci_addr),
> + port->bridge_base_addr
> + + (index * MICROSEMI_ATR0_AXI4_SLV_SIZE)
> + + MICROSEMI_ATR0_AXI4_SLV0_TRSL_ADDR_LSB);
> +
> + break;
> + }
> + index++;
> + }
> +
> + writel(readl(port->bridge_base_addr
> + + MICROSEMI_ATR0_PCIE_WIN0_SRCADDR_31_12)
> + | (MICROSEMI_ATR0_PCIE_WIN0_SIZE
> + << MICROSEMI_ATR0_PCIE_WIN0_SIZE_SHIFT),
> + port->bridge_base_addr +
> + MICROSEMI_ATR0_PCIE_WIN0_SRCADDR_31_12);
> +
> + writel(0x0,
> + port->bridge_base_addr + MICROSEMI_ATR0_PCIE_WIN0_SRCADDR_63_32);
> +
> + writel((readl(port->bridge_base_addr + MICROSEMI_PCIE_PCI_IDS_DW1)
> + & 0xffff)
> + | (PCI_CLASS_BRIDGE_PCI << 16),
> + port->bridge_base_addr + MICROSEMI_PCIE_PCI_IDS_DW1);
> +
> + return 0;
> +}
> +
> +/**
> + * microsemi_pcie_probe - Probe function
> + * @pdev: Platform device pointer
> + *
> + * Return: '0' on success and error value on failure
> + */
> +static int microsemi_pcie_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct microsemi_pcie_port *port;
> + struct pci_bus *bus, *child;
> + struct pci_host_bridge *bridge;
> + int err;
> + resource_size_t iobase = 0;
> + LIST_HEAD(res);
> +
> + if (!dev->of_node)
> + return -ENODEV;
> +
> + bridge = devm_pci_alloc_host_bridge(dev, sizeof(*port));
> + if (!bridge)
> + return -ENODEV;
> +
> + port = pci_host_bridge_priv(bridge);
> +
> + port->dev = dev;
> + port->pdev = pdev;
> +
> + err = microsemi_pcie_init_port(port);
> + if (err) {
> + dev_err(dev, "PCIe port initialization failed\n");
> + return err;
> + }
> +
> + err = microsemi_pcie_init_irq_domain(port);
> + if (err) {
> + dev_err(dev, "failed creating IRQ domain\n");
> + return err;
> + }
> +
> + err = devm_of_pci_get_host_bridge_resources(dev, 0, 0xff, &res,
> + &iobase);
> + if (err) {
> + dev_err(dev, "getting bridge resources failed\n");
> + return err;
> + }
> +
> + err = devm_request_pci_bus_resources(dev, &res);
> + if (err)
> + goto error;
> +
> + list_splice_init(&res, &bridge->windows);
> + bridge->dev.parent = dev;
> + bridge->sysdata = port;
> + bridge->busnr = 0;
> + bridge->ops = µsemi_pcie_ops;
> + bridge->map_irq = of_irq_parse_and_map_pci;
> + bridge->swizzle_irq = pci_common_swizzle;
> +
> +#ifdef CONFIG_PCI_MSI
> + microsemi_pcie_msi_chip.dev = dev;
> + bridge->msi = µsemi_pcie_msi_chip;
> +#endif
> + err = pci_scan_root_bus_bridge(bridge);
> + if (err < 0)
> + goto error;
> +
> + bus = bridge->bus;
> +
> + pci_assign_unassigned_bus_resources(bus);
> + list_for_each_entry(child, &bus->children, node)
> + pcie_bus_configure_settings(child);
> + pci_bus_add_devices(bus);
> +
> + return 0;
> +
> +error:
> + pci_free_resource_list(&res);
> + return err;
> +}
> +
> +static const struct of_device_id microsemi_pcie_of_match[] = {
> + { .compatible = "microsemi,ms-pf-axi-pcie-host", },
> + {}
> +};
> +
> +static struct platform_driver microsemi_pcie_driver = {
> + .driver = {
> + .name = "microsemi-pcie",
> + .of_match_table = microsemi_pcie_of_match,
> + .suppress_bind_attrs = true,
> + },
> + .probe = microsemi_pcie_probe,
> +};
> +builtin_platform_driver(microsemi_pcie_driver);
> --
> 2.17.0
>
---end quoted text---
next prev parent reply other threads:[~2019-02-16 8:04 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-02-15 16:24 [PATCH v3 0/3] Add Microchip/Microsemi PolarFire SoC PCIe support Daire McNamara
2019-02-15 16:24 ` [PATCH v3 1/3] PCI: Add vendor ID for Microsemi Daire McNamara
2019-02-18 18:36 ` Rob Herring
2019-02-15 16:24 ` [PATCH v3 2/3] dt-bindings: PCI: microsemi: Add DT Bindings for Microsemi PCIe host controller Daire McNamara
2019-02-18 18:42 ` Rob Herring
2019-04-02 16:24 ` Lorenzo Pieralisi
2019-02-15 16:24 ` [PATCH v3 3/3] PCI: microsemi: Add host driver for Microsemi PCIe controller Daire McNamara
2019-02-16 8:04 ` Christoph Hellwig [this message]
2019-04-02 18:23 ` Lorenzo Pieralisi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190216080415.GA6506@infradead.org \
--to=hch@infradead.org \
--cc=arnd@arndb.de \
--cc=daire.mcnamara@microchip.com \
--cc=devicetree@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).