Re: [PATCH v9 2/2] PCI: xilinx-cpm: Add Versal CPM Root Port driver

[Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>]

On Wed, Aug 05, 2020 at 03:43:58PM -0500, Bjorn Helgaas wrote:
> On Tue, Jun 16, 2020 at 06:26:54PM +0530, Bharat Kumar Gogada wrote:
> > - Add support for Versal CPM as Root Port.
> > - The Versal ACAP devices include CCIX-PCIe Module (CPM). The integrated
> >   block for CPM along with the integrated bridge can function
> >   as PCIe Root Port.
> > - Bridge error and legacy interrupts in Versal CPM are handled using
> >   Versal CPM specific interrupt line.
> 
> > +static void xilinx_cpm_pcie_init_port(struct xilinx_cpm_pcie_port *port)
> > +{
> > +	if (cpm_pcie_link_up(port))
> > +		dev_info(port->dev, "PCIe Link is UP\n");
> > +	else
> > +		dev_info(port->dev, "PCIe Link is DOWN\n");
> > +
> > +	/* Disable all interrupts */
> > +	pcie_write(port, ~XILINX_CPM_PCIE_IDR_ALL_MASK,
> > +		   XILINX_CPM_PCIE_REG_IMR);
> > +
> > +	/* Clear pending interrupts */
> > +	pcie_write(port, pcie_read(port, XILINX_CPM_PCIE_REG_IDR) &
> > +		   XILINX_CPM_PCIE_IMR_ALL_MASK,
> > +		   XILINX_CPM_PCIE_REG_IDR);
> > +
> > +	/*
> > +	 * XILINX_CPM_PCIE_MISC_IR_ENABLE register is mapped to
> > +	 * CPM SLCR block.
> > +	 */
> > +	writel(XILINX_CPM_PCIE_MISC_IR_LOCAL,
> > +	       port->cpm_base + XILINX_CPM_PCIE_MISC_IR_ENABLE);
> > +	/* Enable the Bridge enable bit */
> > +	pcie_write(port, pcie_read(port, XILINX_CPM_PCIE_REG_RPSC) |
> > +		   XILINX_CPM_PCIE_REG_RPSC_BEN,
> > +		   XILINX_CPM_PCIE_REG_RPSC);
> > +}
> > +
> > +/**
> > + * xilinx_cpm_pcie_parse_dt - Parse Device tree
> > + * @port: PCIe port information
> > + * @bus_range: Bus resource
> > + *
> > + * Return: '0' on success and error value on failure
> > + */
> > +static int xilinx_cpm_pcie_parse_dt(struct xilinx_cpm_pcie_port *port,
> > +				    struct resource *bus_range)
> > +{
> > +	struct device *dev = port->dev;
> > +	struct platform_device *pdev = to_platform_device(dev);
> > +	struct resource *res;
> > +
> > +	port->cpm_base = devm_platform_ioremap_resource_byname(pdev,
> > +							       "cpm_slcr");
> > +	if (IS_ERR(port->cpm_base))
> > +		return PTR_ERR(port->cpm_base);
> > +
> > +	res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "cfg");
> > +	if (!res)
> > +		return -ENXIO;
> > +
> > +	port->cfg = pci_ecam_create(dev, res, bus_range,
> > +				    &pci_generic_ecam_ops);
> 
> Aren't we passing an uninitialized pointer (bus_range) here?  This
> looks broken to me.
> 
> The kernelci build warns about it:
> https://kernelci.org/build/next/branch/master/kernel/next-20200805/
> 
>   /scratch/linux/drivers/pci/controller/pcie-xilinx-cpm.c:557:39: warning: variable 'bus_range' is uninitialized when used here [-Wuninitialized]
> 
> I'm dropping this for now.  I can't believe this actually works.

It is caused by my rebase to fix -next after the rework in pci/misc
(I had to drop the call to pci_parse_request_of_pci_ranges()).

I will look into this tomorrow if Rob does not beat me to it.

Apologies, it is a new driver that was based on an interface
that is being reworked, for good reasons, in pci/misc.

Lorenzo