[RESEND PATCH v1] PCI: pcie_bus_config can be set at build time

[Jim Quinlan <james.quinlan@broadcom.com>]

The Kconfig is modified so that the pcie_bus_config setting can be done at
build time in the same manner as the CONFIG_PCIEASPM_XXXX choice.  The
pci_bus_config setting may still be overridden by the bootline param.

Signed-off-by: Jim Quinlan <james.quinlan@broadcom.com>
---
 drivers/pci/Kconfig | 40 ++++++++++++++++++++++++++++++++++++++++
 drivers/pci/pci.c   | 12 ++++++++++++
 2 files changed, 52 insertions(+)

diff --git a/drivers/pci/Kconfig b/drivers/pci/Kconfig
index 4bef5c2bae9f..efe69b0d9f7f 100644
--- a/drivers/pci/Kconfig
+++ b/drivers/pci/Kconfig
@@ -187,6 +187,46 @@ config PCI_HYPERV
 	  The PCI device frontend driver allows the kernel to import arbitrary
 	  PCI devices from a PCI backend to support PCI driver domains.
 
+choice
+	prompt "PCIE default bus config setting"
+	default PCIE_BUS_DEFAULT
+	depends on PCI
+	help
+	  One of the following choices will set the pci_bus_config at
+	  compile time.  This will still be overridden by the appropriate
+	  pci bootline parameter.
+
+config PCIE_BUS_TUNE_OFF
+	bool "Tune Off"
+	depends on PCI
+	help
+	  Use the BIOS defaults; doesn't touch MPS at all.
+
+config PCIE_BUS_DEFAULT
+	bool "Default"
+	depends on PCI
+	help
+	  Ensure MPS matches upstream bridge.
+
+config PCIE_BUS_SAFE
+	bool "Safe"
+	depends on PCI
+	help
+	  Use largest MPS boot-time devices support.
+
+config PCIE_BUS_PERFORMANCE
+	bool "Performance"
+	depends on PCI
+	help
+	  Use MPS and MRRS for best performance.
+
+config PCIE_BUS_PEER2PEER
+	bool "Peer2peer"
+	depends on PCI
+	help
+	  Set MPS = 128 for all devices.
+endchoice
+
 source "drivers/pci/hotplug/Kconfig"
 source "drivers/pci/controller/Kconfig"
 source "drivers/pci/endpoint/Kconfig"
diff --git a/drivers/pci/pci.c b/drivers/pci/pci.c
index e39c5499770f..dfb52ed4a931 100644
--- a/drivers/pci/pci.c
+++ b/drivers/pci/pci.c
@@ -101,7 +101,19 @@ unsigned long pci_hotplug_mmio_pref_size = DEFAULT_HOTPLUG_MMIO_PREF_SIZE;
 #define DEFAULT_HOTPLUG_BUS_SIZE	1
 unsigned long pci_hotplug_bus_size = DEFAULT_HOTPLUG_BUS_SIZE;
 
+
+/* PCIE bus config, can be overridden by bootline param */
+#ifdef CONFIG_PCIE_BUS_TUNE_OFF
+enum pcie_bus_config_types pcie_bus_config = PCIE_BUS_TUNE_OFF;
+#elif defined CONFIG_PCIE_BUS_SAFE
+enum pcie_bus_config_types pcie_bus_config = PCIE_BUS_SAFE;
+#elif defined CONFIG_PCIE_BUS_PERFORMANCE
+enum pcie_bus_config_types pcie_bus_config = PCIE_BUS_PERFORMANCE;
+#elif defined CONFIG_PCIE_BUS_PEER2PEER
+enum pcie_bus_config_types pcie_bus_config = PCIE_BUS_PEER2PEER;
+#else
 enum pcie_bus_config_types pcie_bus_config = PCIE_BUS_DEFAULT;
+#endif
 
 /*
  * The default CLS is used if arch didn't set CLS explicitly and not
-- 
2.17.1