From: Sean V Kelley <sean.v.kelley@intel.com>
To: bhelgaas@google.com, Jonathan.Cameron@huawei.com,
xerces.zhao@gmail.com, rafael.j.wysocki@intel.com,
ashok.raj@intel.com, tony.luck@intel.com,
sathyanarayanan.kuppuswamy@intel.com, qiuxu.zhuo@intel.com
Cc: linux-pci@vger.kernel.org, linux-kernel@vger.kernel.org,
Sean V Kelley <sean.v.kelley@intel.com>
Subject: [PATCH v10 01/16] AER: aer_root_reset() non-native handling
Date: Thu, 5 Nov 2020 16:14:29 -0800 [thread overview]
Message-ID: <20201106001444.667232-2-sean.v.kelley@intel.com> (raw)
In-Reply-To: <20201106001444.667232-1-sean.v.kelley@intel.com>
If an OS has not been granted AER control via _OSC, then
the OS should not make changes to PCI_ERR_ROOT_COMMAND and
PCI_ERR_ROOT_STATUS related registers. Per section 4.5.1 of
the System Firmware Intermediary (SFI) _OSC and DPC Updates
ECN [1], this bit also covers these aspects of the PCI
Express Advanced Error Reporting. Based on the above and
earlier discussion [2], make the following changes:
Add a check for the native case (i.e., AER control via _OSC)
Note that the current "clear, reset, enable" order suggests that the
reset might cause errors that we should ignore. Lacking historical
context, these will be retained.
[1] System Firmware Intermediary (SFI) _OSC and DPC Updates ECN, Feb 24,
2020, affecting PCI Firmware Specification, Rev. 3.2
https://members.pcisig.com/wg/PCI-SIG/document/14076
[2] https://lore.kernel.org/linux-pci/20201020162820.GA370938@bjorn-Precision-5520/
Signed-off-by: Sean V Kelley <sean.v.kelley@intel.com>
---
drivers/pci/pcie/aer.c | 31 +++++++++++++++++--------------
1 file changed, 17 insertions(+), 14 deletions(-)
diff --git a/drivers/pci/pcie/aer.c b/drivers/pci/pcie/aer.c
index 65dff5f3457a..4ab379fa1506 100644
--- a/drivers/pci/pcie/aer.c
+++ b/drivers/pci/pcie/aer.c
@@ -1358,26 +1358,29 @@ static int aer_probe(struct pcie_device *dev)
static pci_ers_result_t aer_root_reset(struct pci_dev *dev)
{
int aer = dev->aer_cap;
+ int rc = 0;
u32 reg32;
- int rc;
-
- /* Disable Root's interrupt in response to error messages */
- pci_read_config_dword(dev, aer + PCI_ERR_ROOT_COMMAND, ®32);
- reg32 &= ~ROOT_PORT_INTR_ON_MESG_MASK;
- pci_write_config_dword(dev, aer + PCI_ERR_ROOT_COMMAND, reg32);
+ if (pcie_aer_is_native(dev)) {
+ /* Disable Root's interrupt in response to error messages */
+ pci_read_config_dword(dev, aer + PCI_ERR_ROOT_COMMAND, ®32);
+ reg32 &= ~ROOT_PORT_INTR_ON_MESG_MASK;
+ pci_write_config_dword(dev, aer + PCI_ERR_ROOT_COMMAND, reg32);
+ }
rc = pci_bus_error_reset(dev);
- pci_info(dev, "Root Port link has been reset\n");
+ pci_info(dev, "Root Port link has been reset (%d)\n", rc);
- /* Clear Root Error Status */
- pci_read_config_dword(dev, aer + PCI_ERR_ROOT_STATUS, ®32);
- pci_write_config_dword(dev, aer + PCI_ERR_ROOT_STATUS, reg32);
+ if (pcie_aer_is_native(dev)) {
+ /* Clear Root Error Status */
+ pci_read_config_dword(dev, aer + PCI_ERR_ROOT_STATUS, ®32);
+ pci_write_config_dword(dev, aer + PCI_ERR_ROOT_STATUS, reg32);
- /* Enable Root Port's interrupt in response to error messages */
- pci_read_config_dword(dev, aer + PCI_ERR_ROOT_COMMAND, ®32);
- reg32 |= ROOT_PORT_INTR_ON_MESG_MASK;
- pci_write_config_dword(dev, aer + PCI_ERR_ROOT_COMMAND, reg32);
+ /* Enable Root Port's interrupt in response to error messages */
+ pci_read_config_dword(dev, aer + PCI_ERR_ROOT_COMMAND, ®32);
+ reg32 |= ROOT_PORT_INTR_ON_MESG_MASK;
+ pci_write_config_dword(dev, aer + PCI_ERR_ROOT_COMMAND, reg32);
+ }
return rc ? PCI_ERS_RESULT_DISCONNECT : PCI_ERS_RESULT_RECOVERED;
}
--
2.29.2
next prev parent reply other threads:[~2020-11-06 0:16 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-11-06 0:14 [PATCH v10 00/16] Add RCEC handling to PCI/AER Sean V Kelley
2020-11-06 0:14 ` Sean V Kelley [this message]
2020-11-06 0:14 ` [PATCH v10 02/16] PCI/RCEC: Add RCEC class code and extended capability Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 03/16] PCI/RCEC: Bind RCEC devices to the Root Port driver Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 04/16] PCI/RCEC: Cache RCEC capabilities in pci_init_capabilities() Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 05/16] PCI/ERR: Rename reset_link() to reset_subordinates() Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 06/16] PCI/ERR: Simplify by using pci_upstream_bridge() Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 07/16] PCI/ERR: Simplify by computing pci_pcie_type() once Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 08/16] PCI/ERR: Use "bridge" for clarity in pcie_do_recovery() Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 09/16] PCI/ERR: Avoid negated conditional for clarity Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 10/16] PCI/ERR: Add pci_walk_bridge() to pcie_do_recovery() Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 11/16] PCI/ERR: Limit AER resets in pcie_do_recovery() Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 12/16] PCI/RCEC: Add pcie_link_rcec() to associate RCiEPs Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 13/16] PCI/RCEC: Add RCiEP's linked RCEC to AER/ERR Sean V Kelley
2020-11-06 0:40 ` Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 14/16] PCI/AER: Add pcie_walk_rcec() to RCEC AER handling Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 15/16] PCI/PME: Add pcie_walk_rcec() to RCEC PME handling Sean V Kelley
2020-11-06 0:14 ` [PATCH v10 16/16] PCI/AER: Add RCEC AER error injection support Sean V Kelley
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20201106001444.667232-2-sean.v.kelley@intel.com \
--to=sean.v.kelley@intel.com \
--cc=Jonathan.Cameron@huawei.com \
--cc=ashok.raj@intel.com \
--cc=bhelgaas@google.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pci@vger.kernel.org \
--cc=qiuxu.zhuo@intel.com \
--cc=rafael.j.wysocki@intel.com \
--cc=sathyanarayanan.kuppuswamy@intel.com \
--cc=tony.luck@intel.com \
--cc=xerces.zhao@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).