[PATCH AUTOSEL 5.10 05/37] PCI: ftpci100: Rename macro name collision

[PATCH AUTOSEL 5.10 05/37] PCI: ftpci100: Rename macro name collision

[Sasha Levin]

From: Randy Dunlap <rdunlap@infradead.org>

[ Upstream commit 5be967d5016ac5ffb9c4d0df51b48441ee4d5ed1 ]

PCI_IOSIZE is defined in mach-loongson64/spaces.h, so change the name
of the PCI_* macros in pci-ftpci100.c to use FTPCI_* so that they are
more localized and won't conflict with other drivers or arches.

../drivers/pci/controller/pci-ftpci100.c:37: warning: "PCI_IOSIZE" redefined
   37 | #define PCI_IOSIZE 0x00
      |
In file included from ../arch/mips/include/asm/addrspace.h:13,
...              from ../drivers/pci/controller/pci-ftpci100.c:15:
arch/mips/include/asm/mach-loongson64/spaces.h:11: note: this is the location of the previous definition
   11 | #define PCI_IOSIZE SZ_16M

Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20210517234117.3660-1-rdunlap@infradead.org
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Jiaxun Yang <jiaxun.yang@flygoat.com>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Krzysztof Wilczyński <kw@linux.com>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/pci-ftpci100.c | 30 +++++++++++++--------------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/drivers/pci/controller/pci-ftpci100.c b/drivers/pci/controller/pci-ftpci100.c
index da3cd216da00..aefef1986201 100644
--- a/drivers/pci/controller/pci-ftpci100.c
+++ b/drivers/pci/controller/pci-ftpci100.c
@@ -34,12 +34,12 @@
  * Special configuration registers directly in the first few words
  * in I/O space.
  */
-#define PCI_IOSIZE	0x00
-#define PCI_PROT	0x04 /* AHB protection */
-#define PCI_CTRL	0x08 /* PCI control signal */
-#define PCI_SOFTRST	0x10 /* Soft reset counter and response error enable */
-#define PCI_CONFIG	0x28 /* PCI configuration command register */
-#define PCI_DATA	0x2C
+#define FTPCI_IOSIZE	0x00
+#define FTPCI_PROT	0x04 /* AHB protection */
+#define FTPCI_CTRL	0x08 /* PCI control signal */
+#define FTPCI_SOFTRST	0x10 /* Soft reset counter and response error enable */
+#define FTPCI_CONFIG	0x28 /* PCI configuration command register */
+#define FTPCI_DATA	0x2C
 
 #define FARADAY_PCI_STATUS_CMD		0x04 /* Status and command */
 #define FARADAY_PCI_PMC			0x40 /* Power management control */
@@ -195,9 +195,9 @@ static int faraday_raw_pci_read_config(struct faraday_pci *p, int bus_number,
 			PCI_CONF_FUNCTION(PCI_FUNC(fn)) |
 			PCI_CONF_WHERE(config) |
 			PCI_CONF_ENABLE,
-			p->base + PCI_CONFIG);
+			p->base + FTPCI_CONFIG);
 
-	*value = readl(p->base + PCI_DATA);
+	*value = readl(p->base + FTPCI_DATA);
 
 	if (size == 1)
 		*value = (*value >> (8 * (config & 3))) & 0xFF;
@@ -230,17 +230,17 @@ static int faraday_raw_pci_write_config(struct faraday_pci *p, int bus_number,
 			PCI_CONF_FUNCTION(PCI_FUNC(fn)) |
 			PCI_CONF_WHERE(config) |
 			PCI_CONF_ENABLE,
-			p->base + PCI_CONFIG);
+			p->base + FTPCI_CONFIG);
 
 	switch (size) {
 	case 4:
-		writel(value, p->base + PCI_DATA);
+		writel(value, p->base + FTPCI_DATA);
 		break;
 	case 2:
-		writew(value, p->base + PCI_DATA + (config & 3));
+		writew(value, p->base + FTPCI_DATA + (config & 3));
 		break;
 	case 1:
-		writeb(value, p->base + PCI_DATA + (config & 3));
+		writeb(value, p->base + FTPCI_DATA + (config & 3));
 		break;
 	default:
 		ret = PCIBIOS_BAD_REGISTER_NUMBER;
@@ -469,7 +469,7 @@ static int faraday_pci_probe(struct platform_device *pdev)
 		if (!faraday_res_to_memcfg(io->start - win->offset,
 					   resource_size(io), &val)) {
 			/* setup I/O space size */
-			writel(val, p->base + PCI_IOSIZE);
+			writel(val, p->base + FTPCI_IOSIZE);
 		} else {
 			dev_err(dev, "illegal IO mem size\n");
 			return -EINVAL;
@@ -477,11 +477,11 @@ static int faraday_pci_probe(struct platform_device *pdev)
 	}
 
 	/* Setup hostbridge */
-	val = readl(p->base + PCI_CTRL);
+	val = readl(p->base + FTPCI_CTRL);
 	val |= PCI_COMMAND_IO;
 	val |= PCI_COMMAND_MEMORY;
 	val |= PCI_COMMAND_MASTER;
-	writel(val, p->base + PCI_CTRL);
+	writel(val, p->base + FTPCI_CTRL);
 	/* Mask and clear all interrupts */
 	faraday_raw_pci_write_config(p, 0, 0, FARADAY_PCI_CTRL2 + 2, 2, 0xF000);
 	if (variant->cascaded_irq) {
-- 
2.30.2

[PATCH AUTOSEL 5.10 07/37] PCI: hv: Fix a race condition when removing the device

[Sasha Levin]

From: Long Li <longli@microsoft.com>

[ Upstream commit 94d22763207ac6633612b8d8e0ca4fba0f7aa139 ]

On removing the device, any work item (hv_pci_devices_present() or
hv_pci_eject_device()) scheduled on workqueue hbus->wq may still be running
and race with hv_pci_remove().

This can happen because the host may send PCI_EJECT or PCI_BUS_RELATIONS(2)
and decide to rescind the channel immediately after that.

Fix this by flushing/destroying the workqueue of hbus before doing hbus remove.

Link: https://lore.kernel.org/r/1620806800-30983-1-git-send-email-longli@linuxonhyperv.com
Signed-off-by: Long Li <longli@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/pci-hyperv.c | 30 ++++++++++++++++++++++-------
 1 file changed, 23 insertions(+), 7 deletions(-)

diff --git a/drivers/pci/controller/pci-hyperv.c b/drivers/pci/controller/pci-hyperv.c
index 03ed5cb1c4b2..4932d7677be2 100644
--- a/drivers/pci/controller/pci-hyperv.c
+++ b/drivers/pci/controller/pci-hyperv.c
@@ -444,7 +444,6 @@ enum hv_pcibus_state {
 	hv_pcibus_probed,
 	hv_pcibus_installed,
 	hv_pcibus_removing,
-	hv_pcibus_removed,
 	hv_pcibus_maximum
 };
 
@@ -3247,8 +3246,9 @@ static int hv_pci_bus_exit(struct hv_device *hdev, bool keep_devs)
 		struct pci_packet teardown_packet;
 		u8 buffer[sizeof(struct pci_message)];
 	} pkt;
-	struct hv_dr_state *dr;
 	struct hv_pci_compl comp_pkt;
+	struct hv_pci_dev *hpdev, *tmp;
+	unsigned long flags;
 	int ret;
 
 	/*
@@ -3260,9 +3260,16 @@ static int hv_pci_bus_exit(struct hv_device *hdev, bool keep_devs)
 
 	if (!keep_devs) {
 		/* Delete any children which might still exist. */
-		dr = kzalloc(sizeof(*dr), GFP_KERNEL);
-		if (dr && hv_pci_start_relations_work(hbus, dr))
-			kfree(dr);
+		spin_lock_irqsave(&hbus->device_list_lock, flags);
+		list_for_each_entry_safe(hpdev, tmp, &hbus->children, list_entry) {
+			list_del(&hpdev->list_entry);
+			if (hpdev->pci_slot)
+				pci_destroy_slot(hpdev->pci_slot);
+			/* For the two refs got in new_pcichild_device() */
+			put_pcichild(hpdev);
+			put_pcichild(hpdev);
+		}
+		spin_unlock_irqrestore(&hbus->device_list_lock, flags);
 	}
 
 	ret = hv_send_resources_released(hdev);
@@ -3305,13 +3312,23 @@ static int hv_pci_remove(struct hv_device *hdev)
 
 	hbus = hv_get_drvdata(hdev);
 	if (hbus->state == hv_pcibus_installed) {
+		tasklet_disable(&hdev->channel->callback_event);
+		hbus->state = hv_pcibus_removing;
+		tasklet_enable(&hdev->channel->callback_event);
+		destroy_workqueue(hbus->wq);
+		hbus->wq = NULL;
+		/*
+		 * At this point, no work is running or can be scheduled
+		 * on hbus-wq. We can't race with hv_pci_devices_present()
+		 * or hv_pci_eject_device(), it's safe to proceed.
+		 */
+
 		/* Remove the bus from PCI's point of view. */
 		pci_lock_rescan_remove();
 		pci_stop_root_bus(hbus->pci_bus);
 		hv_pci_remove_slots(hbus);
 		pci_remove_root_bus(hbus->pci_bus);
 		pci_unlock_rescan_remove();
-		hbus->state = hv_pcibus_removed;
 	}
 
 	ret = hv_pci_bus_exit(hdev, false);
@@ -3326,7 +3343,6 @@ static int hv_pci_remove(struct hv_device *hdev)
 	irq_domain_free_fwnode(hbus->sysdata.fwnode);
 	put_hvpcibus(hbus);
 	wait_for_completion(&hbus->remove_event);
-	destroy_workqueue(hbus->wq);
 
 	hv_put_dom_num(hbus->sysdata.domain);
 
-- 
2.30.2

[PATCH AUTOSEL 5.10 11/37] PCI/P2PDMA: Avoid pci_get_slot(), which may sleep

[Sasha Levin]

From: Logan Gunthorpe <logang@deltatee.com>

[ Upstream commit 3ec0c3ec2d92c09465534a1ff9c6f9d9506ffef6 ]

In order to use upstream_bridge_distance_warn() from a dma_map function, it
must not sleep. However, pci_get_slot() takes the pci_bus_sem so it might
sleep.

In order to avoid this, try to get the host bridge's device from the first
element in the device list. It should be impossible for the host bridge's
device to go away while references are held on child devices, so the first
element should not be able to change and, thus, this should be safe.

Introduce a static function called pci_host_bridge_dev() to obtain the host
bridge's root device.

Link: https://lore.kernel.org/r/20210610160609.28447-7-logang@deltatee.com
Signed-off-by: Logan Gunthorpe <logang@deltatee.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/p2pdma.c | 34 ++++++++++++++++++++++++++++++++--
 1 file changed, 32 insertions(+), 2 deletions(-)

diff --git a/drivers/pci/p2pdma.c b/drivers/pci/p2pdma.c
index de1c331dbed4..f07c5dbc94e1 100644
--- a/drivers/pci/p2pdma.c
+++ b/drivers/pci/p2pdma.c
@@ -308,10 +308,41 @@ static const struct pci_p2pdma_whitelist_entry {
 	{}
 };
 
+/*
+ * This lookup function tries to find the PCI device corresponding to a given
+ * host bridge.
+ *
+ * It assumes the host bridge device is the first PCI device in the
+ * bus->devices list and that the devfn is 00.0. These assumptions should hold
+ * for all the devices in the whitelist above.
+ *
+ * This function is equivalent to pci_get_slot(host->bus, 0), however it does
+ * not take the pci_bus_sem lock seeing __host_bridge_whitelist() must not
+ * sleep.
+ *
+ * For this to be safe, the caller should hold a reference to a device on the
+ * bridge, which should ensure the host_bridge device will not be freed
+ * or removed from the head of the devices list.
+ */
+static struct pci_dev *pci_host_bridge_dev(struct pci_host_bridge *host)
+{
+	struct pci_dev *root;
+
+	root = list_first_entry_or_null(&host->bus->devices,
+					struct pci_dev, bus_list);
+
+	if (!root)
+		return NULL;
+	if (root->devfn != PCI_DEVFN(0, 0))
+		return NULL;
+
+	return root;
+}
+
 static bool __host_bridge_whitelist(struct pci_host_bridge *host,
 				    bool same_host_bridge)
 {
-	struct pci_dev *root = pci_get_slot(host->bus, PCI_DEVFN(0, 0));
+	struct pci_dev *root = pci_host_bridge_dev(host);
 	const struct pci_p2pdma_whitelist_entry *entry;
 	unsigned short vendor, device;
 
@@ -320,7 +351,6 @@ static bool __host_bridge_whitelist(struct pci_host_bridge *host,
 
 	vendor = root->vendor;
 	device = root->device;
-	pci_dev_put(root);
 
 	for (entry = pci_p2pdma_whitelist; entry->vendor; entry++) {
 		if (vendor != entry->vendor || device != entry->device)
-- 
2.30.2

[PATCH AUTOSEL 5.10 13/37] PCI: pciehp: Ignore Link Down/Up caused by DPC

[Sasha Levin]

From: Lukas Wunner <lukas@wunner.de>

[ Upstream commit a97396c6eb13f65bea894dbe7739b2e883d40a3e ]

Downstream Port Containment (PCIe r5.0, sec. 6.2.10) disables the link upon
an error and attempts to re-enable it when instructed by the DPC driver.

A slot which is both DPC- and hotplug-capable is currently powered off by
pciehp once DPC is triggered (due to the link change) and powered back up
on successful recovery.  That's undesirable, the slot should remain powered
so the hotplugged device remains bound to its driver.  DPC notifies the
driver of the error and of successful recovery in pcie_do_recovery() and
the driver may then restore the device to working state.

Moreover, Sinan points out that turning off slot power by pciehp may foil
recovery by DPC:  Power off/on is a cold reset concurrently to DPC's warm
reset.  Sathyanarayanan reports extended delays or failure in link
retraining by DPC if pciehp brings down the slot.

Fix by detecting whether a Link Down event is caused by DPC and awaiting
recovery if so.  On successful recovery, ignore both the Link Down and the
subsequent Link Up event.

Afterwards, check whether the link is down to detect surprise-removal or
another DPC event immediately after DPC recovery.  Ensure that the
corresponding DLLSC event is not ignored by synthesizing it and invoking
irq_wake_thread() to trigger a re-run of pciehp_ist().

The IRQ threads of the hotplug and DPC drivers, pciehp_ist() and
dpc_handler(), race against each other.  If pciehp is faster than DPC, it
will wait until DPC recovery completes.

Recovery consists of two steps:  The first step (waiting for link
disablement) is recognizable by pciehp through a set DPC Trigger Status
bit.  The second step (waiting for link retraining) is recognizable through
a newly introduced PCI_DPC_RECOVERING flag.

If DPC is faster than pciehp, neither of the two flags will be set and
pciehp may glean the recovery status from the new PCI_DPC_RECOVERED flag.
The flag is zero if DPC didn't occur at all, hence DLLSC events are not
ignored by default.

pciehp waits up to 4 seconds before assuming that DPC recovery failed and
bringing down the slot.  This timeout is not taken from the spec (it
doesn't mandate one) but based on a report from Yicong Yang that DPC may
take a bit more than 3 seconds on HiSilicon's Kunpeng platform.

The timeout is necessary because the DPC Trigger Status bit may never
clear:  On Root Ports which support RP Extensions for DPC, the DPC driver
polls the DPC RP Busy bit for up to 1 second before giving up on DPC
recovery.  Without the timeout, pciehp would then wait indefinitely for DPC
to complete.

This commit draws inspiration from previous attempts to synchronize DPC
with pciehp:

By Sinan Kaya, August 2018:
https://lore.kernel.org/linux-pci/20180818065126.77912-1-okaya@kernel.org/

By Ethan Zhao, October 2020:
https://lore.kernel.org/linux-pci/20201007113158.48933-1-haifeng.zhao@intel.com/

By Kuppuswamy Sathyanarayanan, March 2021:
https://lore.kernel.org/linux-pci/59cb30f5e5ac6d65427ceaadf1012b2ba8dbf66c.1615606143.git.sathyanarayanan.kuppuswamy@linux.intel.com/

Link: https://lore.kernel.org/r/0be565d97438fe2a6d57354b3aa4e8626952a00b.1619857124.git.lukas@wunner.de
Reported-by: Sinan Kaya <okaya@kernel.org>
Reported-by: Ethan Zhao <haifeng.zhao@intel.com>
Reported-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Tested-by: Yicong Yang <yangyicong@hisilicon.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Ashok Raj <ashok.raj@intel.com>
Cc: Keith Busch <kbusch@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/hotplug/pciehp_hpc.c | 36 ++++++++++++++++
 drivers/pci/pci.h                |  4 ++
 drivers/pci/pcie/dpc.c           | 74 +++++++++++++++++++++++++++++---
 3 files changed, 109 insertions(+), 5 deletions(-)

diff --git a/drivers/pci/hotplug/pciehp_hpc.c b/drivers/pci/hotplug/pciehp_hpc.c
index fb3840e222ad..9d06939736c0 100644
--- a/drivers/pci/hotplug/pciehp_hpc.c
+++ b/drivers/pci/hotplug/pciehp_hpc.c
@@ -563,6 +563,32 @@ void pciehp_power_off_slot(struct controller *ctrl)
 		 PCI_EXP_SLTCTL_PWR_OFF);
 }
 
+static void pciehp_ignore_dpc_link_change(struct controller *ctrl,
+					  struct pci_dev *pdev, int irq)
+{
+	/*
+	 * Ignore link changes which occurred while waiting for DPC recovery.
+	 * Could be several if DPC triggered multiple times consecutively.
+	 */
+	synchronize_hardirq(irq);
+	atomic_and(~PCI_EXP_SLTSTA_DLLSC, &ctrl->pending_events);
+	if (pciehp_poll_mode)
+		pcie_capability_write_word(pdev, PCI_EXP_SLTSTA,
+					   PCI_EXP_SLTSTA_DLLSC);
+	ctrl_info(ctrl, "Slot(%s): Link Down/Up ignored (recovered by DPC)\n",
+		  slot_name(ctrl));
+
+	/*
+	 * If the link is unexpectedly down after successful recovery,
+	 * the corresponding link change may have been ignored above.
+	 * Synthesize it to ensure that it is acted on.
+	 */
+	down_read(&ctrl->reset_lock);
+	if (!pciehp_check_link_active(ctrl))
+		pciehp_request(ctrl, PCI_EXP_SLTSTA_DLLSC);
+	up_read(&ctrl->reset_lock);
+}
+
 static irqreturn_t pciehp_isr(int irq, void *dev_id)
 {
 	struct controller *ctrl = (struct controller *)dev_id;
@@ -706,6 +732,16 @@ static irqreturn_t pciehp_ist(int irq, void *dev_id)
 				      PCI_EXP_SLTCTL_ATTN_IND_ON);
 	}
 
+	/*
+	 * Ignore Link Down/Up events caused by Downstream Port Containment
+	 * if recovery from the error succeeded.
+	 */
+	if ((events & PCI_EXP_SLTSTA_DLLSC) && pci_dpc_recovered(pdev) &&
+	    ctrl->state == ON_STATE) {
+		events &= ~PCI_EXP_SLTSTA_DLLSC;
+		pciehp_ignore_dpc_link_change(ctrl, pdev, irq);
+	}
+
 	/*
 	 * Disable requests have higher priority than Presence Detect Changed
 	 * or Data Link Layer State Changed events.
diff --git a/drivers/pci/pci.h b/drivers/pci/pci.h
index 09ebc134d0d7..a96dc6f53076 100644
--- a/drivers/pci/pci.h
+++ b/drivers/pci/pci.h
@@ -409,6 +409,8 @@ static inline bool pci_dev_is_disconnected(const struct pci_dev *dev)
 
 /* pci_dev priv_flags */
 #define PCI_DEV_ADDED 0
+#define PCI_DPC_RECOVERED 1
+#define PCI_DPC_RECOVERING 2
 
 static inline void pci_dev_assign_added(struct pci_dev *dev, bool added)
 {
@@ -454,10 +456,12 @@ void pci_restore_dpc_state(struct pci_dev *dev);
 void pci_dpc_init(struct pci_dev *pdev);
 void dpc_process_error(struct pci_dev *pdev);
 pci_ers_result_t dpc_reset_link(struct pci_dev *pdev);
+bool pci_dpc_recovered(struct pci_dev *pdev);
 #else
 static inline void pci_save_dpc_state(struct pci_dev *dev) {}
 static inline void pci_restore_dpc_state(struct pci_dev *dev) {}
 static inline void pci_dpc_init(struct pci_dev *pdev) {}
+static inline bool pci_dpc_recovered(struct pci_dev *pdev) { return false; }
 #endif
 
 #ifdef CONFIG_PCI_ATS
diff --git a/drivers/pci/pcie/dpc.c b/drivers/pci/pcie/dpc.c
index e05aba86a317..c556e7beafe3 100644
--- a/drivers/pci/pcie/dpc.c
+++ b/drivers/pci/pcie/dpc.c
@@ -71,6 +71,58 @@ void pci_restore_dpc_state(struct pci_dev *dev)
 	pci_write_config_word(dev, dev->dpc_cap + PCI_EXP_DPC_CTL, *cap);
 }
 
+static DECLARE_WAIT_QUEUE_HEAD(dpc_completed_waitqueue);
+
+#ifdef CONFIG_HOTPLUG_PCI_PCIE
+static bool dpc_completed(struct pci_dev *pdev)
+{
+	u16 status;
+
+	pci_read_config_word(pdev, pdev->dpc_cap + PCI_EXP_DPC_STATUS, &status);
+	if ((status != 0xffff) && (status & PCI_EXP_DPC_STATUS_TRIGGER))
+		return false;
+
+	if (test_bit(PCI_DPC_RECOVERING, &pdev->priv_flags))
+		return false;
+
+	return true;
+}
+
+/**
+ * pci_dpc_recovered - whether DPC triggered and has recovered successfully
+ * @pdev: PCI device
+ *
+ * Return true if DPC was triggered for @pdev and has recovered successfully.
+ * Wait for recovery if it hasn't completed yet.  Called from the PCIe hotplug
+ * driver to recognize and ignore Link Down/Up events caused by DPC.
+ */
+bool pci_dpc_recovered(struct pci_dev *pdev)
+{
+	struct pci_host_bridge *host;
+
+	if (!pdev->dpc_cap)
+		return false;
+
+	/*
+	 * Synchronization between hotplug and DPC is not supported
+	 * if DPC is owned by firmware and EDR is not enabled.
+	 */
+	host = pci_find_host_bridge(pdev->bus);
+	if (!host->native_dpc && !IS_ENABLED(CONFIG_PCIE_EDR))
+		return false;
+
+	/*
+	 * Need a timeout in case DPC never completes due to failure of
+	 * dpc_wait_rp_inactive().  The spec doesn't mandate a time limit,
+	 * but reports indicate that DPC completes within 4 seconds.
+	 */
+	wait_event_timeout(dpc_completed_waitqueue, dpc_completed(pdev),
+			   msecs_to_jiffies(4000));
+
+	return test_and_clear_bit(PCI_DPC_RECOVERED, &pdev->priv_flags);
+}
+#endif /* CONFIG_HOTPLUG_PCI_PCIE */
+
 static int dpc_wait_rp_inactive(struct pci_dev *pdev)
 {
 	unsigned long timeout = jiffies + HZ;
@@ -91,8 +143,11 @@ static int dpc_wait_rp_inactive(struct pci_dev *pdev)
 
 pci_ers_result_t dpc_reset_link(struct pci_dev *pdev)
 {
+	pci_ers_result_t ret;
 	u16 cap;
 
+	set_bit(PCI_DPC_RECOVERING, &pdev->priv_flags);
+
 	/*
 	 * DPC disables the Link automatically in hardware, so it has
 	 * already been reset by the time we get here.
@@ -106,18 +161,27 @@ pci_ers_result_t dpc_reset_link(struct pci_dev *pdev)
 	if (!pcie_wait_for_link(pdev, false))
 		pci_info(pdev, "Data Link Layer Link Active not cleared in 1000 msec\n");
 
-	if (pdev->dpc_rp_extensions && dpc_wait_rp_inactive(pdev))
-		return PCI_ERS_RESULT_DISCONNECT;
+	if (pdev->dpc_rp_extensions && dpc_wait_rp_inactive(pdev)) {
+		clear_bit(PCI_DPC_RECOVERED, &pdev->priv_flags);
+		ret = PCI_ERS_RESULT_DISCONNECT;
+		goto out;
+	}
 
 	pci_write_config_word(pdev, cap + PCI_EXP_DPC_STATUS,
 			      PCI_EXP_DPC_STATUS_TRIGGER);
 
 	if (!pcie_wait_for_link(pdev, true)) {
 		pci_info(pdev, "Data Link Layer Link Active not set in 1000 msec\n");
-		return PCI_ERS_RESULT_DISCONNECT;
+		clear_bit(PCI_DPC_RECOVERED, &pdev->priv_flags);
+		ret = PCI_ERS_RESULT_DISCONNECT;
+	} else {
+		set_bit(PCI_DPC_RECOVERED, &pdev->priv_flags);
+		ret = PCI_ERS_RESULT_RECOVERED;
 	}
-
-	return PCI_ERS_RESULT_RECOVERED;
+out:
+	clear_bit(PCI_DPC_RECOVERING, &pdev->priv_flags);
+	wake_up_all(&dpc_completed_waitqueue);
+	return ret;
 }
 
 static void dpc_process_rp_pio_error(struct pci_dev *pdev)
-- 
2.30.2

[PATCH AUTOSEL 5.10 21/37] PCI: tegra: Add missing MODULE_DEVICE_TABLE

[Sasha Levin]

From: Zou Wei <zou_wei@huawei.com>

[ Upstream commit 7bf475a4614a9722b9b989e53184a02596cf16d1 ]

Add missing MODULE_DEVICE_TABLE definition so we generate correct modalias
for automatic loading of this driver when it is built as a module.

Link: https://lore.kernel.org/r/1620792422-16535-1-git-send-email-zou_wei@huawei.com
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Vidya Sagar <vidyas@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/pci-tegra.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/pci/controller/pci-tegra.c b/drivers/pci/controller/pci-tegra.c
index 8fcabed7c6a6..1a2af963599c 100644
--- a/drivers/pci/controller/pci-tegra.c
+++ b/drivers/pci/controller/pci-tegra.c
@@ -2506,6 +2506,7 @@ static const struct of_device_id tegra_pcie_of_match[] = {
 	{ .compatible = "nvidia,tegra20-pcie", .data = &tegra20_pcie },
 	{ },
 };
+MODULE_DEVICE_TABLE(of, tegra_pcie_of_match);
 
 static void *tegra_pcie_ports_seq_start(struct seq_file *s, loff_t *pos)
 {
-- 
2.30.2

[PATCH AUTOSEL 5.10 33/37] PCI: rockchip: Register IRQ handlers after device and data are ready

[Sasha Levin]

From: Javier Martinez Canillas <javierm@redhat.com>

[ Upstream commit 3cf5f7ab230e2b886e493c7a8449ed50e29d2b98 ]

An IRQ handler may be called at any time after it is registered, so
anything it relies on must be ready before registration.

rockchip_pcie_subsys_irq_handler() and rockchip_pcie_client_irq_handler()
read registers in the PCIe controller, but we registered them before
turning on clocks to the controller.  If either is called before the clocks
are turned on, the register reads fail and the machine hangs.

Similarly, rockchip_pcie_legacy_int_handler() uses rockchip->irq_domain,
but we installed it before initializing irq_domain.

Register IRQ handlers after their data structures are initialized and
clocks are enabled.

Found by enabling CONFIG_DEBUG_SHIRQ, which calls the IRQ handler when it
is being unregistered.  An error during the probe path might cause this
unregistration and IRQ handler execution before the device or data
structure init has finished.

[bhelgaas: commit log]
Link: https://lore.kernel.org/r/20210608080409.1729276-1-javierm@redhat.com
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/pci/controller/pcie-rockchip-host.c | 12 ++++++------
 1 file changed, 6 insertions(+), 6 deletions(-)

diff --git a/drivers/pci/controller/pcie-rockchip-host.c b/drivers/pci/controller/pcie-rockchip-host.c
index 9705059523a6..0d6df73bb918 100644
--- a/drivers/pci/controller/pcie-rockchip-host.c
+++ b/drivers/pci/controller/pcie-rockchip-host.c
@@ -593,10 +593,6 @@ static int rockchip_pcie_parse_host_dt(struct rockchip_pcie *rockchip)
 	if (err)
 		return err;
 
-	err = rockchip_pcie_setup_irq(rockchip);
-	if (err)
-		return err;
-
 	rockchip->vpcie12v = devm_regulator_get_optional(dev, "vpcie12v");
 	if (IS_ERR(rockchip->vpcie12v)) {
 		if (PTR_ERR(rockchip->vpcie12v) != -ENODEV)
@@ -974,8 +970,6 @@ static int rockchip_pcie_probe(struct platform_device *pdev)
 	if (err)
 		goto err_vpcie;
 
-	rockchip_pcie_enable_interrupts(rockchip);
-
 	err = rockchip_pcie_init_irq_domain(rockchip);
 	if (err < 0)
 		goto err_deinit_port;
@@ -993,6 +987,12 @@ static int rockchip_pcie_probe(struct platform_device *pdev)
 	bridge->sysdata = rockchip;
 	bridge->ops = &rockchip_pcie_ops;
 
+	err = rockchip_pcie_setup_irq(rockchip);
+	if (err)
+		goto err_remove_irq_domain;
+
+	rockchip_pcie_enable_interrupts(rockchip);
+
 	err = pci_host_probe(bridge);
 	if (err < 0)
 		goto err_remove_irq_domain;
-- 
2.30.2