From: Yijing Wang <wangyijing@huawei.com>
To: Martin Mokrejs <mmokrejs@fold.natur.cuni.cz>
Cc: "linux-pci@vger.kernel.org" <linux-pci@vger.kernel.org>,
Bjorn Helgaas <bhelgaas@google.com>,
"Rafael J. Wysocki" <rjw@sisk.pl>,
Yinghai Lu <yinghai@kernel.org>
Subject: Re: 3.9-rc1: pciehp and eSATA card SiI 3132, no XHCI
Date: Wed, 13 Mar 2013 10:42:53 +0800 [thread overview]
Message-ID: <513FE7AD.2020408@huawei.com> (raw)
In-Reply-To: <513E7E1E.80508@fold.natur.cuni.cz>
Hi Martin,
From your diff info, maybe we can analyze this problem step by step.
1、According to your diff info about first eject and first hot add, the pci device 11:00.0 Mass storage
controller was removed and was added ok at pci device level;
2、The main problem is 11:00.0 Mass storage controller can not bind its driver normally, right?
3、According to diff info about first hotadd and coldplug, the mainly diff is
> + Region 0: Memory at f6c84000 (64-bit, non-prefetchable) [disabled] [size=128]
> + Region 2: Memory at f6c80000 (64-bit, non-prefetchable) [disabled] [size=16K]
> + Region 4: I/O ports at c000 [disabled] [size=128]
and
MaxReadReq 4096 bytes ----> MaxReadReq 512 bytes
So maybe we can try to find why the memory range was disabled after hot add.
Martin, can you provide /proc/iomem info when the system bootup, after first eject and
first hot-add?
I suspect the driver release its MMIO successfully after first eject.
Thanks!
Yijing.
On 2013/3/12 9:00, Martin Mokrejs wrote:
> Hi,
> I cold-booted a computer with the card inserted before power-on and collected
> lspci output and express card slot status every second. Then I tried eject and
> hotplug inserts and it appearts the card is not detected, actually maybe pciehp
> is not even suppoosed to work in this case as the slot was occupied during boot.
> But let me come to it later.
>
> I noted the following on the very first eject of the so far cold-plugged card
> that lspci properly reports PresDet change on the Changed: line. The only time
> I ever saw it. ;-)
> However, for any following inserts and ejects the value is not updated but slot
> status bits are updated. I had BIOS defaults loaded and additionally, disabled
> MediaCardReader.
>
> The slot status bits read by setpci were changing in this path:
> card in slot and cold boot 0040 -> eject 0100 hotplug insert -> 0140 eject -> 0100 hotplug insert -> 0140 eject -> 0100
>
>
>
> --- lspci_loop.23:58:50 2013-03-11 23:58:50.000000000 +0100
> +++ lspci_loop.23:58:51 2013-03-11 23:58:51.000000000 +0100
> @@ -439,7 +439,7 @@
> I/O behind bridge: 0000c000-0000dfff
> Memory behind bridge: f6c00000-f7cfffff
> Prefetchable memory behind bridge: 00000000f0000000-00000000f10fffff
> - Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> + Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
> @@ -453,13 +453,13 @@
> ClockPM- Surprise- LLActRep+ BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> - LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> + LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
> Slot #7, PowerLimit 10.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> - SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> - Changed: MRL- PresDet- LinkState-
> + SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
> + Changed: MRL- PresDet+ LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> @@ -478,11 +478,11 @@
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: pcieport
> 00: 86 80 1e 1c 07 00 10 00 b5 00 04 06 10 00 81 00
> -10: 00 00 00 00 00 00 00 00 00 11 16 00 c0 d0 00 00
> +10: 00 00 00 00 00 00 00 00 00 11 16 00 c0 d0 00 20
> 20: c0 f6 c0 f7 01 f0 01 f1 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00
> 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 3c 12 08
> -50: 40 00 11 70 60 b2 3c 00 00 00 40 00 00 00 00 00
> +50: 40 00 11 50 60 b2 3c 00 00 00 08 01 00 00 00 00
> 60: 00 00 00 00 16 00 00 00 00 00 00 00 00 00 00 00
> 70: 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> @@ -490,7 +490,7 @@
> a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -d0: 00 00 00 01 02 0b 00 00 02 80 11 c1 00 00 00 00
> +d0: 00 00 00 01 02 0b 00 00 02 80 11 c1 00 00 00 40
> e0: 00 03 00 00 00 00 00 00 01 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 87 0f 05 08 00 00 00 00
>
> @@ -797,55 +797,23 @@
> e0: 00 00 40 63 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> -11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
> - Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller
> - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> - Latency: 0, Cache Line Size: 64 bytes
> - Interrupt: pin A routed to IRQ 19
> - Region 0: Memory at f6c84000 (64-bit, non-prefetchable) [size=128]
> - Region 2: Memory at f6c80000 (64-bit, non-prefetchable) [size=16K]
> - Region 4: I/O ports at c000 [size=128]
> - Expansion ROM at f6c00000 [disabled] [size=512K]
> - Capabilities: [54] Power Management version 2
> - Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
> - Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+
> - Address: 0000000000000000 Data: 0000
> - Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
> - DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
> - ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
> - DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> - RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> - MaxPayload 128 bytes, MaxReadReq 4096 bytes
> - DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
> - LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
> - ClockPM- Surprise- LLActRep- BwNot-
> - LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> - ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> - LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> - Capabilities: [100 v1] Advanced Error Reporting
> - UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
> - UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> - UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> - CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> - CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> - AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> +11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev ff) (prog-if ff)
> + !!! Unknown header type 7f
> Kernel driver in use: sata_sil24
> -00: 95 10 32 31 07 00 10 00 01 00 80 01 10 00 00 00
> -10: 04 40 c8 f6 00 00 00 00 04 00 c8 f6 00 00 00 00
> -20: 01 c0 00 00 00 00 00 00 00 00 00 00 95 10 32 31
> -30: 00 00 c0 f6 54 00 00 00 00 00 00 00 0a 01 00 00
> -40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -50: 00 00 00 00 01 5c 22 06 00 20 00 0c 05 70 80 00
> -60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -70: 10 00 11 00 03 00 00 00 00 50 0a 00 11 f4 03 00
> -80: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
> -90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> --- lspci_loop.23:58:51 2013-03-11 23:58:51.000000000 +0100
> +++ lspci_loop.23:58:52 2013-03-11 23:58:52.000000000 +0100
> @@ -459,7 +459,7 @@
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
> - Changed: MRL- PresDet+ LinkState+
> + Changed: MRL- PresDet- LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> @@ -482,7 +482,7 @@
> 20: c0 f6 c0 f7 01 f0 01 f1 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00
> 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 3c 12 08
> -50: 40 00 11 50 60 b2 3c 00 00 00 08 01 00 00 00 00
> +50: 40 00 11 50 60 b2 3c 00 00 00 00 01 00 00 00 00
> 60: 00 00 00 00 16 00 00 00 00 00 00 00 00 00 00 00
> 70: 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> @@ -490,7 +490,7 @@
> a0: 01 00 02 c8 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -d0: 00 00 00 01 02 0b 00 00 02 80 11 c1 00 00 00 40
> +d0: 00 00 00 01 02 0b 00 00 02 80 11 c1 00 00 00 00
> e0: 00 03 00 00 00 00 00 00 01 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 87 0f 05 08 00 00 00 00
> --- lspci_loop.23:58:58 2013-03-11 23:58:58.000000000 +0100
> +++ lspci_loop.23:58:59 2013-03-11 23:58:59.000000000 +0100
> @@ -101,7 +101,7 @@
> Capabilities: [98] PCI Advanced Features
> AFCap: TP+ FLR+
> AFCtrl: FLR-
> - AFStatus: TP-
> + AFStatus: TP+
> Kernel driver in use: ehci-pci
> 00: 86 80 2d 1c 06 00 90 02 05 20 03 0c 00 00 00 00
> 10: 00 80 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
> --- lspci_loop.23:58:59 2013-03-11 23:58:59.000000000 +0100
> +++ lspci_loop.23:59:00 2013-03-11 23:59:00.000000000 +0100
> @@ -101,7 +101,7 @@
> Capabilities: [98] PCI Advanced Features
> AFCap: TP+ FLR+
> AFCtrl: FLR-
> - AFStatus: TP+
> + AFStatus: TP-
> Kernel driver in use: ehci-pci
> 00: 86 80 2d 1c 06 00 90 02 05 20 03 0c 00 00 00 00
> 10: 00 80 f0 f7 00 00 00 00 00 00 00 00 00 00 00 00
>
>
>
> Below is the first hotplug of the card.
>
> --- lspci_loop.23:59:09 2013-03-11 23:59:09.000000000 +0100
> +++ lspci_loop.23:59:10 2013-03-11 23:59:10.000000000 +0100
> @@ -453,12 +453,12 @@
> ClockPM- Surprise- LLActRep+ BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> - LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
> + LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
> Slot #7, PowerLimit 10.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> - SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
> + SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> Changed: MRL- PresDet- LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> RootCap: CRSVisible-
> @@ -482,7 +482,7 @@
> 20: c0 f6 c0 f7 01 f0 01 f1 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00
> 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 3c 12 08
> -50: 40 00 11 50 60 b2 3c 00 00 00 00 01 00 00 00 00
> +50: 40 00 11 70 60 b2 3c 00 00 00 40 01 00 00 00 00
> 60: 00 00 00 00 16 00 00 00 00 00 00 00 00 00 00 00
> 70: 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> @@ -797,23 +797,54 @@
> e0: 00 00 40 63 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> -11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev ff) (prog-if ff)
> - !!! Unknown header type 7f
> +11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
> + Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller
> + Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> + Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> + Interrupt: pin A routed to IRQ 19
> + Region 0: Memory at f6c84000 (64-bit, non-prefetchable) [disabled] [size=128]
> + Region 2: Memory at f6c80000 (64-bit, non-prefetchable) [disabled] [size=16K]
> + Region 4: I/O ports at c000 [disabled] [size=128]
> + [virtual] Expansion ROM at f6c00000 [disabled] [size=512K]
> + Capabilities: [54] Power Management version 2
> + Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> + Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
> + Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+
> + Address: 0000000000000000 Data: 0000
> + Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
> + DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
> + ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
> + DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> + RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> + MaxPayload 128 bytes, MaxReadReq 512 bytes
> + DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
> + LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
> + ClockPM- Surprise- LLActRep- BwNot-
> + LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> + ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> + LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> + Capabilities: [100 v1] Advanced Error Reporting
> + UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
> + UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> + UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> + CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> + CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> + AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> Kernel driver in use: sata_sil24
> -00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> -f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +00: 95 10 32 31 00 00 10 00 01 00 80 01 00 00 00 00
> +10: 04 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00
> +20: 01 00 00 00 00 00 00 00 00 00 00 00 95 10 32 31
> +30: 00 00 00 00 54 00 00 00 00 00 00 00 00 01 00 00
> +40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +50: 00 00 00 00 01 5c 22 06 00 20 00 0c 05 70 80 00
> +60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +70: 10 00 11 00 03 00 00 00 00 20 0a 00 11 f4 03 00
> +80: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
> +90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> --- lspci_loop.23:59:15 2013-03-11 23:59:15.000000000 +0100
> +++ lspci_loop.23:59:16 2013-03-11 23:59:16.000000000 +0100
> @@ -519,7 +519,7 @@
> 60: 20 20 ff 07 00 00 00 00 01 00 00 01 00 00 08 40
> 70: 00 00 df 3f 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 80 00 11 88 0c 93 30 0d 00 24 00 00 00 00
> -90: 00 00 00 00 00 00 00 00 13 00 06 03 00 00 00 00
> +90: 00 00 00 00 00 00 00 00 13 00 06 03 00 01 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> --- lspci_loop.23:59:16 2013-03-11 23:59:16.000000000 +0100
> +++ lspci_loop.23:59:17 2013-03-11 23:59:17.000000000 +0100
> @@ -519,7 +519,7 @@
> 60: 20 20 ff 07 00 00 00 00 01 00 00 01 00 00 08 40
> 70: 00 00 df 3f 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 00 00 80 00 11 88 0c 93 30 0d 00 24 00 00 00 00
> -90: 00 00 00 00 00 00 00 00 13 00 06 03 00 01 00 00
> +90: 00 00 00 00 00 00 00 00 13 00 06 03 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
>
> And later unplug of the hotplugged device:
>
> --- lspci_loop.23:59:18 2013-03-11 23:59:18.000000000 +0100
> +++ lspci_loop.23:59:19 2013-03-11 23:59:19.000000000 +0100
> @@ -453,12 +453,12 @@
> ClockPM- Surprise- LLActRep+ BwNot-
> LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> - LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
> + LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt+ ABWMgmt-
> SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug+ Surprise+
> Slot #7, PowerLimit 10.000W; Interlock- NoCompl+
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> - SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> + SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
> Changed: MRL- PresDet- LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> RootCap: CRSVisible-
> @@ -482,7 +482,7 @@
> 20: c0 f6 c0 f7 01 f0 01 f1 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00
> 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 3c 12 08
> -50: 40 00 11 70 60 b2 3c 00 00 00 40 01 00 00 00 00
> +50: 40 00 11 50 60 b2 3c 00 00 00 00 01 00 00 00 00
> 60: 00 00 00 00 16 00 00 00 00 00 00 00 00 00 00 00
> 70: 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> @@ -797,54 +797,23 @@
> e0: 00 00 40 63 00 00 00 00 00 00 00 00 00 00 00 00
> f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
> -11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
> - Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller
> - Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> - Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> - Interrupt: pin A routed to IRQ 19
> - Region 0: Memory at f6c84000 (64-bit, non-prefetchable) [disabled] [size=128]
> - Region 2: Memory at f6c80000 (64-bit, non-prefetchable) [disabled] [size=16K]
> - Region 4: I/O ports at c000 [disabled] [size=128]
> - [virtual] Expansion ROM at f6c00000 [disabled] [size=512K]
> - Capabilities: [54] Power Management version 2
> - Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> - Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
> - Capabilities: [5c] MSI: Enable- Count=1/1 Maskable- 64bit+
> - Address: 0000000000000000 Data: 0000
> - Capabilities: [70] Express (v1) Legacy Endpoint, MSI 00
> - DevCap: MaxPayload 1024 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
> - ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
> - DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> - RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> - MaxPayload 128 bytes, MaxReadReq 512 bytes
> - DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
> - LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
> - ClockPM- Surprise- LLActRep- BwNot-
> - LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
> - ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
> - LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
> - Capabilities: [100 v1] Advanced Error Reporting
> - UESta: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
> - UEMsk: DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
> - UESvrt: DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
> - CESta: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> - CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> - AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> +11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev ff) (prog-if ff)
> + !!! Unknown header type 7f
> Kernel driver in use: sata_sil24
> -00: 95 10 32 31 00 00 10 00 01 00 80 01 00 00 00 00
> -10: 04 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00
> -20: 01 00 00 00 00 00 00 00 00 00 00 00 95 10 32 31
> -30: 00 00 00 00 54 00 00 00 00 00 00 00 00 01 00 00
> -40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -50: 00 00 00 00 01 5c 22 06 00 20 00 0c 05 70 80 00
> -60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -70: 10 00 11 00 03 00 00 00 00 20 0a 00 11 f4 03 00
> -80: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
> -90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -b0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> +00: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +10: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +20: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +30: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +40: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +50: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +60: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +70: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +80: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +90: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +a0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +b0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +c0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +d0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +e0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
> +f0: ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff
>
>
>
>
>
> Already from other tests I realized a hotplugged eSATA has some "[virtual]
> Expansion ROM". Here is a reasonably complete diff between a coldplugged
> state of the same card and after a hotplug. In dmesg pciehp complained
> upon its loading that Cache Line Size 64 is not supported so maybe the below
> difference is a direct result of that? Similarly, MaxReadReq is different
> and I bet the lines
>
> + Region 0: Memory at f6c84000 (64-bit, non-prefetchable) [disabled] [size=128]
> + Region 2: Memory at f6c80000 (64-bit, non-prefetchable) [disabled] [size=16K]
> + Region 4: I/O ports at c000 [disabled] [size=128]
>
> actually mean the card is left disabled. Then, I am not surprised nothing
> is shown upon its hotplug insert/eject in dmesg. ;-) In this particular setup
> I don't think we are facing a PresDet issue. Either, the value is overwritten
> by some other process, or the bug is somewhere else.
>
>
> --- lspci_loop.23:58:26 2013-03-11 23:58:26.000000000 +0100
> +++ lspci_loop.23:59:10 2013-03-11 23:59:10.000000000 +0100
> @@ -439,7 +439,7 @@
> I/O behind bridge: 0000c000-0000dfff
> Memory behind bridge: f6c00000-f7cfffff
> Prefetchable memory behind bridge: 00000000f0000000-00000000f10fffff
> - Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
> + Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
> BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
> PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
> Capabilities: [40] Express (v2) Root Port (Slot+), MSI 00
> @@ -459,7 +459,7 @@
> SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
> Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
> SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
> - Changed: MRL- PresDet- LinkState-
> + Changed: MRL- PresDet- LinkState+
> RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
> RootCap: CRSVisible-
> RootSta: PME ReqID 0000, PMEStatus- PMEPending-
> @@ -478,11 +478,11 @@
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
> Kernel driver in use: pcieport
> 00: 86 80 1e 1c 07 00 10 00 b5 00 04 06 10 00 81 00
> -10: 00 00 00 00 00 00 00 00 00 11 16 00 c0 d0 00 00
> +10: 00 00 00 00 00 00 00 00 00 11 16 00 c0 d0 00 20
> 20: c0 f6 c0 f7 01 f0 01 f1 00 00 00 00 00 00 00 00
> 30: 00 00 00 00 40 00 00 00 00 00 00 00 0a 04 10 00
> 40: 10 80 42 01 00 80 00 00 00 00 10 00 12 3c 12 08
> -50: 40 00 11 70 60 b2 3c 00 00 00 40 00 00 00 00 00
> +50: 40 00 11 70 60 b2 3c 00 00 00 40 01 00 00 00 00
> 60: 00 00 00 00 16 00 00 00 00 00 00 00 00 00 00 00
> 70: 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00
> 80: 05 90 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> @@ -799,14 +799,13 @@
>
> 11:00.0 Mass storage controller: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller (rev 01)
> Subsystem: Silicon Image, Inc. SiI 3132 Serial ATA Raid II Controller
> - Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> + Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
> Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
> - Latency: 0, Cache Line Size: 64 bytes
> Interrupt: pin A routed to IRQ 19
> - Region 0: Memory at f6c84000 (64-bit, non-prefetchable) [size=128]
> - Region 2: Memory at f6c80000 (64-bit, non-prefetchable) [size=16K]
> - Region 4: I/O ports at c000 [size=128]
> - Expansion ROM at f6c00000 [disabled] [size=512K]
> + Region 0: Memory at f6c84000 (64-bit, non-prefetchable) [disabled] [size=128]
> + Region 2: Memory at f6c80000 (64-bit, non-prefetchable) [disabled] [size=16K]
> + Region 4: I/O ports at c000 [disabled] [size=128]
> + [virtual] Expansion ROM at f6c00000 [disabled] [size=512K]
> Capabilities: [54] Power Management version 2
> Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
> Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=1 PME-
> @@ -817,7 +816,7 @@
> ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
> DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
> RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
> - MaxPayload 128 bytes, MaxReadReq 4096 bytes
> + MaxPayload 128 bytes, MaxReadReq 512 bytes
> DevSta: CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr- TransPend-
> LnkCap: Port #0, Speed 2.5GT/s, Width x1, ASPM L0s, Latency L0 unlimited, L1 unlimited
> ClockPM- Surprise- LLActRep- BwNot-
> @@ -832,14 +831,14 @@
> CEMsk: RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
> AERCap: First Error Pointer: 14, GenCap+ CGenEn- ChkCap+ ChkEn-
> Kernel driver in use: sata_sil24
> -00: 95 10 32 31 07 00 10 00 01 00 80 01 10 00 00 00
> -10: 04 40 c8 f6 00 00 00 00 04 00 c8 f6 00 00 00 00
> -20: 01 c0 00 00 00 00 00 00 00 00 00 00 95 10 32 31
> -30: 00 00 c0 f6 54 00 00 00 00 00 00 00 0a 01 00 00
> +00: 95 10 32 31 00 00 10 00 01 00 80 01 00 00 00 00
> +10: 04 00 00 00 00 00 00 00 04 00 00 00 00 00 00 00
> +20: 01 00 00 00 00 00 00 00 00 00 00 00 95 10 32 31
> +30: 00 00 00 00 54 00 00 00 00 00 00 00 00 01 00 00
> 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> 50: 00 00 00 00 01 5c 22 06 00 20 00 0c 05 70 80 00
> 60: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> -70: 10 00 11 00 03 00 00 00 00 50 0a 00 11 f4 03 00
> +70: 10 00 11 00 03 00 00 00 00 20 0a 00 11 f4 03 00
> 80: 40 00 11 10 00 00 00 00 00 00 00 00 00 00 00 00
> 90: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> a0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>
>
>
> Sadly, although the very first eject was notified the sata_sila24 neither
> did "release" the device nor did it complain that it suddenly disappeared.
> That was so far always in dmesg output (like for example):
>
> [ 251.632928] sata_sil24 0000:11:00.0: PME# disabled
> [ 251.636498] sata_sil24: IRQ status == 0xffffffff, PCI fault or device removal?
>
>
> I re-plugged the card and ejected several times while the while loops
> collecting lspci and slot_status via the setpci shell command harvested
> data. Still, in dmesg there was nothing logged regarding card insert/eject.
> Eventually, I tried rmmod sata_sil24 (did NOT need 'rmmod -f') and that
> did log something new.
>
> [ 529.571040] ata8.00: disabled
> [ 529.576365] sd 7:0:0:0: [sdb] Synchronizing SCSI cache
> [ 529.577202] sd 7:0:0:0: [sdb]
> [ 529.577204] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [ 529.577205] sd 7:0:0:0: [sdb] Stopping disk
> [ 529.577251] sd 7:0:0:0: [sdb] START_STOP FAILED
> [ 529.577253] sd 7:0:0:0: [sdb]
> [ 529.577254] Result: hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK
> [ 529.578309] sata_sil24: IRQ status == 0xffffffff, PCI fault or device removal?
> [ 605.818905] sata_sil24 0000:11:00.0: version 1.1
> [ 605.818923] sata_sil24 0000:11:00.0: enabling device (0000 -> 0003)
> [ 605.914722] sata_sil24 0000:11:00.0: failed to clear port RST
> [ 606.014860] sata_sil24 0000:11:00.0: failed to clear port RST
> [ 606.014882] sata_sil24 0000:11:00.0: enabling bus mastering
> [ 606.017741] scsi8 : sata_sil24
> [ 606.019388] scsi9 : sata_sil24
> [ 606.019898] ata9: SATA max UDMA/100 host m128@0xf6c84000 port 0xf6c80000 irq 19
> [ 606.019902] ata10: SATA max UDMA/100 host m128@0xf6c84000 port 0xf6c82000 irq 19
> [ 606.115003] ata9: controller in dubious state, performing PORT_RST
> [ 608.327747] ata9: SATA link down (SStatus FFFFFFFF SControl FFFFFFFF)
> [ 608.427847] ata10: controller in dubious state, performing PORT_RST
> [ 610.640619] ata10: SATA link down (SStatus FFFFFFFF SControl FFFFFFFF)
>
>
>
>
> Finally, I am tempted to say that pciehp does not work at all under 3.9-rc1
> if the slot was occupied during boot. It does NOT contain the usual debug
> info spanning several lines and it only said:
>
> [ 2.109629] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
> [ 2.110225] pciehp: pcie_port_service_register = 0
> [ 2.110226] pciehp: PCI Express Hot Plug Controller Driver version: 0.4
>
> If that is intentional the driver should complain loudly. Please educate me
> what those "[virtual] Expansion ROM's" were in lspci above and whether those
> "[disabled]" memory ranges relate to that as well. If the card is not thought
> to be present or just not recognized ... why is that printed in lspci at all?
> Similarly, what can you tell me if lspci output shows only:
>
> Latency: 0
>
> or even lacks the whole "Latency" line altoghether, is that also a disabled device?
>
> I believe in working cases there is "Latency: 0, Cache Line Size: 64 bytes" instead.
>
>
>
> Details and raw files at: http://195.113.57.32/~mmokrejs/tmp/3.9-rc1_disabled_MediaCard_reader_eSATA_coldplugged.tar.bz2
>
> To inspect the incremental diffs of lspci output I used:
>
> prev='/dev/null'; ls -latr lspci_* | awk '{print $9}' | while read cur; do diff -u -w $prev $cur | less; prev=$cur; done
>
> Thank you,
> Martin
> --
> To unsubscribe from this list: send the line "unsubscribe linux-pci" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
> .
>
--
Thanks!
Yijing
next prev parent reply other threads:[~2013-03-13 2:43 UTC|newest]
Thread overview: 41+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-03-12 1:00 3.9-rc1: pciehp and eSATA card SiI 3132, no XHCI Martin Mokrejs
2013-03-12 2:51 ` Yijing Wang
2013-03-12 9:57 ` Martin Mokrejs
2013-03-13 2:42 ` Yijing Wang [this message]
2013-03-14 0:05 ` Martin Mokrejs
2013-03-14 0:16 ` Martin Mokrejs
2013-03-14 8:38 ` Yijing Wang
[not found] ` <51417C28.40402@huawei.com>
2013-03-14 13:00 ` Martin Mokrejs
2013-03-15 2:41 ` Yijing Wang
2013-03-28 18:38 ` Martin Mokrejs
2013-03-29 8:20 ` Huang Ying
2013-03-29 13:08 ` Martin Mokrejs
2013-03-29 14:38 ` Huang Ying
2013-03-29 15:12 ` Martin Mokrejs
2013-03-29 14:11 ` Martin Mokrejs
2013-03-29 16:45 ` Martin Mokrejs
2013-03-29 21:31 ` Rafael J. Wysocki
2013-03-30 1:17 ` Martin Mokrejs
2013-03-30 1:48 ` Rafael J. Wysocki
2013-03-30 1:53 ` Martin Mokrejs
2013-03-30 17:49 ` Martin Mokrejs
2013-03-30 22:18 ` Rafael J. Wysocki
2013-03-30 23:12 ` Martin Mokrejs
2013-03-31 1:51 ` Rafael J. Wysocki
2013-03-30 22:17 ` Rafael J. Wysocki
2013-03-30 22:39 ` Martin Mokrejs
2013-03-30 10:54 ` Huang Ying
2013-03-31 10:35 ` Martin Mokrejs
2013-03-31 14:12 ` Huang Ying
2013-03-31 15:04 ` Martin Mokrejs
2013-04-01 7:33 ` Huang Ying
2013-04-01 17:23 ` Martin Mokrejs
2013-04-30 21:09 ` Martin Mokrejs
2013-05-01 0:20 ` Martin Mokrejs
[not found] ` <515813CB.8020001@fold.natur.cuni.cz>
2013-03-31 23:17 ` Martin Mokrejs
2013-04-01 0:14 ` Rafael J. Wysocki
2013-04-01 12:06 ` Martin Mokrejs
2013-03-31 18:48 ` Martin Mokrejs
2013-03-14 15:18 ` Martin Mokrejs
2013-03-14 15:20 ` Martin Mokrejs
2013-03-14 17:54 ` Martin Mokrejs
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=513FE7AD.2020408@huawei.com \
--to=wangyijing@huawei.com \
--cc=bhelgaas@google.com \
--cc=linux-pci@vger.kernel.org \
--cc=mmokrejs@fold.natur.cuni.cz \
--cc=rjw@sisk.pl \
--cc=yinghai@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).