Re: [PATCH v4 02/11] PCI/bwctrl: Add support to scale bandwidth before & after link re-training

[Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>]

On 7/22/2025 4:33 PM, Krishna Chaitanya Chundru wrote:
> 
> 
> On 7/12/2025 4:36 AM, Krishna Chaitanya Chundru wrote:
>>
>>
>> On 7/12/2025 3:06 AM, Bjorn Helgaas wrote:
>>> On Mon, Jun 09, 2025 at 04:21:23PM +0530, Krishna Chaitanya Chundru 
>>> wrote:
>>>> If the driver wants to move to higher data rate/speed than the 
>>>> current data
>>>> rate then the controller driver may need to change certain votes so 
>>>> that
>>>> link may come up at requested data rate/speed like QCOM PCIe 
>>>> controllers
>>>> need to change their RPMh (Resource Power Manager-hardened) state. Once
>>>> link retraining is done controller drivers needs to adjust their votes
>>>> based on the final data rate.
>>>>
>>>> Some controllers also may need to update their bandwidth voting like
>>>> ICC BW votings etc.
>>>>
>>>> So, add pre_link_speed_change() & post_link_speed_change() op to call
>>>> before & after the link re-train. There is no explicit locking 
>>>> mechanisms
>>>> as these are called by a single client Endpoint driver.
>>>>
>>>> In case of PCIe switch, if there is a request to change target speed 
>>>> for a
>>>> downstream port then no need to call these function ops as these are
>>>> outside the scope of the controller drivers.
>>>
>>>> +++ b/include/linux/pci.h
>>>> @@ -599,6 +599,24 @@ struct pci_host_bridge {
>>>>       void (*release_fn)(struct pci_host_bridge *);
>>>>       int (*enable_device)(struct pci_host_bridge *bridge, struct 
>>>> pci_dev *dev);
>>>>       void (*disable_device)(struct pci_host_bridge *bridge, struct 
>>>> pci_dev *dev);
>>>> +    /*
>>>> +     * Callback to the host bridge drivers to update ICC BW votes, 
>>>> clock
>>>> +     * frequencies etc.. for the link re-train to come up in 
>>>> targeted speed.
>>>> +     * These are intended to be called by devices directly attached 
>>>> to the
>>>> +     * Root Port. These are called by a single client Endpoint 
>>>> driver, so
>>>> +     * there is no need for explicit locking mechanisms.
>>>> +     */
>>>> +    int (*pre_link_speed_change)(struct pci_host_bridge *bridge,
>>>> +                     struct pci_dev *dev, int speed);
>>>> +    /*
>>>> +     * Callback to the host bridge drivers to adjust ICC BW votes, 
>>>> clock
>>>> +     * frequencies etc.. to the updated speed after link re-train. 
>>>> These
>>>> +     * are intended to be called by devices directly attached to the
>>>> +     * Root Port. These are called by a single client Endpoint driver,
>>>> +     * so there is no need for explicit locking mechanisms.
>>>
>>> No need to repeat the entire comment.  s/.././
>>>
>>> These pointers feel awfully specific for being in struct
>>> pci_host_bridge, since we only need them for a questionable QCOM
>>> controller.  I think this needs to be pushed down into qcom somehow as
>>> some kind of quirk.
>>>
>> Currently these are needed by QCOM controllers, but it may also needed
>> by other controllers may also need these for updating ICC votes, any
>> system level votes, clock frequencies etc.
>> QCOM controllers is also doing one extra step in these functions to
>> disable and enable ASPM only as it cannot link speed change support
>> with ASPM enabled.
>>
> Bjorn, can you check this.
> 
> For QCOM devices we need to update the RPMh vote i.e a power source
> votes for the link to come up in required speed. and also we need
> to update interconnect votes also. This will be applicable for
> other vendors also.
> 
> If this is not correct place I can add them in the pci_ops.
Bjorn,

Can you please comment on this.

Is this fine to move these to the pci_ops of the bridge.
Again these are not specific to QCOM, any controller driver which
needs to change their clock rates, ICC bw votes etc needs to have
these.

- Krishna Chaitanya.
> - Krishna Chaitanya.
>> - Krishna Chaitanya.
>>>> +     */
>>>> +    void (*post_link_speed_change)(struct pci_host_bridge *bridge,
>>>> +                       struct pci_dev *dev, int speed);