Re: [PATCH v2 1/3] dt-bindings: phy: Add starfive,jh7110-dphy-rx

From: Rob Herring <robh@kernel.org>
To: Changhuang Liang <changhuang.liang@starfivetech.com>
Cc: Vinod Koul <vkoul@kernel.org>,
	Kishon Vijay Abraham I <kishon@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Emil Renner Berthing <kernel@esmil.dk>,
	Conor Dooley <conor@kernel.org>,
	Paul Walmsley <paul.walmsley@sifive.com>,
	Palmer Dabbelt <palmer@dabbelt.com>,
	Albert Ou <aou@eecs.berkeley.edu>,
	Philipp Zabel <p.zabel@pengutronix.de>,
	Jack Zhu <jack.zhu@starfivetech.com>,
	linux-phy@lists.infradead.org, devicetree@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-riscv@lists.infradead.org
Subject: Re: [PATCH v2 1/3] dt-bindings: phy: Add starfive,jh7110-dphy-rx
Date: Mon, 27 Feb 2023 12:34:34 -0600	[thread overview]
Message-ID: <20230227183434.GA642331-robh@kernel.org> (raw)
In-Reply-To: <20230223015952.201841-2-changhuang.liang@starfivetech.com>

On Wed, Feb 22, 2023 at 05:59:50PM -0800, Changhuang Liang wrote:
> Starfive SoCs like the jh7110 use a MIPI D-PHY RX controller based on
> a M31 IP. Add a binding for it.
> 
> Signed-off-by: Changhuang Liang <changhuang.liang@starfivetech.com>
> ---
>  .../bindings/phy/starfive,jh7110-dphy-rx.yaml | 74 +++++++++++++++++++
>  1 file changed, 74 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/starfive,jh7110-dphy-rx.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/starfive,jh7110-dphy-rx.yaml b/Documentation/devicetree/bindings/phy/starfive,jh7110-dphy-rx.yaml
> new file mode 100644
> index 000000000000..a67ca57a6f21
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/starfive,jh7110-dphy-rx.yaml
> @@ -0,0 +1,74 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/starfive,jh7110-dphy-rx.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Starfive SoC MIPI D-PHY Rx Controller
> +
> +maintainers:
> +  - Jack Zhu <jack.zhu@starfivetech.com>
> +  - Changhuang Liang <changhuang.liang@starfivetech.com>
> +
> +description:
> +  The Starfive SoC uses the MIPI CSI D-PHY based on M31 IP to transfer
> +  CSI camera data.
> +
> +properties:
> +  compatible:
> +    const: starfive,jh7110-dphy-rx
> +
> +  reg:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 3
> +
> +  clock-names:
> +    items:
> +      - const: cfg
> +      - const: ref
> +      - const: tx

Should be 'rx' given this is the 'rx' block? A description of each clock 
in 'clocks' would be good.

> +
> +  resets:
> +    items:
> +      - description: DPHY_HW reset
> +      - description: DPHY_B09_ALWAYS_ON reset
> +
> +  starfive,aon-syscon:
> +    $ref: /schemas/types.yaml#/definitions/phandle-array
> +    items:
> +      items:

- items: ?

Otherwise, multiple 2 cell entries are allowed. Is that intended?

> +        - description: phandle of AON SYSCON
> +        - description: register offset
> +    description: The power of dphy rx is configured by AON SYSCON
> +      in this property.

> +
> +  "#phy-cells":
> +    const: 0
> +
> +required:
> +  - compatible
> +  - reg
> +  - clocks
> +  - clock-names
> +  - resets
> +  - starfive,aon-syscon
> +  - "#phy-cells"
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    phy@19820000 {
> +      compatible = "starfive,jh7110-dphy-rx";
> +      reg = <0x19820000 0x10000>;
> +      clocks = <&ispcrg 3>,
> +               <&ispcrg 4>,
> +               <&ispcrg 5>;
> +      clock-names = "cfg", "ref", "tx";
> +      resets = <&ispcrg 2>,
> +               <&ispcrg 3>;
> +      starfive,aon-syscon = <&aon_syscon 0x00>;
> +      #phy-cells = <0>;
> +    };
> -- 
> 2.25.1
> 

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy