linux-phy.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: Adam Ford <aford173@gmail.com>
To: linux-phy@lists.infradead.org
Cc: dominique.martinet@atmark-techno.com, linux-imx@nxp.com,
	festevam@gmail.com, frieder.schrempf@kontron.de,
	aford@beaconembedded.com, Sandor.yu@nxp.com,
	"Adam Ford" <aford173@gmail.com>, "Vinod Koul" <vkoul@kernel.org>,
	"Kishon Vijay Abraham I" <kishon@kernel.org>,
	"Lucas Stach" <l.stach@pengutronix.de>,
	"Marco Felsch" <m.felsch@pengutronix.de>,
	"Uwe Kleine-König" <u.kleine-koenig@pengutronix.de>,
	linux-kernel@vger.kernel.org
Subject: [PATCH V4 3/5] phy: freescale: fsl-samsung-hdmi: Support dynamic integer
Date: Mon,  2 Sep 2024 20:30:45 -0500	[thread overview]
Message-ID: <20240903013113.139698-4-aford173@gmail.com> (raw)
In-Reply-To: <20240903013113.139698-1-aford173@gmail.com>

There is currently a look-up table for a variety of resolutions.
Since the phy has the ability to dynamically calculate the values
necessary to use the intger divider which should allow more
resolutions without having to update the look-up-table.

If the lookup table cannot find an exact match, fall back to the
dynamic calculator of the integer divider.

Previously, the value of P was hard-coded to 1, this required an
update to the phy_pll_cfg table to add in the extra value into the
table, so if the value of P is calculated to be something else
by the PMS calculator, the calculated_phy_pll_cfg structure
can be used instead without having to keep track of which method
was used.

Signed-off-by: Adam Ford <aford173@gmail.com>
---
V3:  Change size of pll_div_regs to include PHY_REG01 (P)
     Create calculated_phy_pll_cfg to containe the values
     Eliminate the PMS calculation from fsl_samsung_hdmi_phy_configure
     Make the LUT primary and fall back to integer calculator in
     phy_clk_round_rate.
     Check the range right away to ensure it's reaonsable rather than
     trying to find a clock only to learn it's outside the range.
     Overall added notes and comments where stuff may not be intuitive.

V2:  Update phy_clk_round_rate and phy_clk_set_rate to both support
     the integer clock PMS calculator.
---
 drivers/phy/freescale/phy-fsl-samsung-hdmi.c | 341 +++++++++++++------
 1 file changed, 235 insertions(+), 106 deletions(-)

diff --git a/drivers/phy/freescale/phy-fsl-samsung-hdmi.c b/drivers/phy/freescale/phy-fsl-samsung-hdmi.c
index a700a300dc6f..8822029526f0 100644
--- a/drivers/phy/freescale/phy-fsl-samsung-hdmi.c
+++ b/drivers/phy/freescale/phy-fsl-samsung-hdmi.c
@@ -16,6 +16,8 @@
 
 #define PHY_REG(reg)		(reg * 4)
 
+#define REG01_PMS_P_MASK	GENMASK(3, 0)
+#define REG03_PMS_S_MASK	GENMASK(7, 4)
 #define REG12_CK_DIV_MASK	GENMASK(5, 4)
 #define REG13_TG_CODE_LOW_MASK	GENMASK(7, 0)
 #define REG14_TOL_MASK		GENMASK(7, 4)
@@ -29,281 +31,296 @@
 #define REG34_PLL_LOCK		BIT(6)
 #define REG34_PHY_CLK_READY	BIT(5)
 
-#define PHY_PLL_DIV_REGS_NUM 6
+#ifndef MHZ
+#define MHZ	(1000UL * 1000UL)
+#endif
+
+#define PHY_PLL_DIV_REGS_NUM 7
 
 struct phy_config {
 	u32	pixclk;
 	u8	pll_div_regs[PHY_PLL_DIV_REGS_NUM];
 };
 
+/*
+ * The calculated_phy_pll_cfg only handles integer divider for PMS only,
+ * meaning the last four entries will be fixed, but the first three will
+ * be calculated by the PMS calculator
+ */
+static struct phy_config calculated_phy_pll_cfg = {
+	.pixclk = 0,
+	.pll_div_regs = { 0x00, 0x00, 0x00, 0x00, 0x00, 0x80, 0x00 },
+};
+
+/* The lookup table contains values for which the fractional divder is used */
 static const struct phy_config phy_pll_cfg[] = {
 	{
 		.pixclk = 22250000,
-		.pll_div_regs = { 0x4b, 0xf1, 0x89, 0x88, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x4b, 0xf1, 0x89, 0x88, 0x80, 0x40 },
 	}, {
 		.pixclk = 23750000,
-		.pll_div_regs = { 0x50, 0xf1, 0x86, 0x85, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x50, 0xf1, 0x86, 0x85, 0x80, 0x40 },
 	}, {
 		.pixclk = 24000000,
-		.pll_div_regs = { 0x50, 0xf0, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x50, 0xf0, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 24024000,
-		.pll_div_regs = { 0x50, 0xf1, 0x99, 0x02, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x50, 0xf1, 0x99, 0x02, 0x80, 0x40 },
 	}, {
 		.pixclk = 25175000,
-		.pll_div_regs = { 0x54, 0xfc, 0xcc, 0x91, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x54, 0xfc, 0xcc, 0x91, 0x80, 0x40 },
 	}, {
 		.pixclk = 25200000,
-		.pll_div_regs = { 0x54, 0xf0, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x54, 0xf0, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 26750000,
-		.pll_div_regs = { 0x5a, 0xf2, 0x89, 0x88, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0xf2, 0x89, 0x88, 0x80, 0x40 },
 	}, {
 		.pixclk = 27000000,
-		.pll_div_regs = { 0x5a, 0xf0, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x5a, 0xf0, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 27027000,
-		.pll_div_regs = { 0x5a, 0xf2, 0xfd, 0x0c, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0xf2, 0xfd, 0x0c, 0x80, 0x40 },
 	}, {
 		.pixclk = 29500000,
-		.pll_div_regs = { 0x62, 0xf4, 0x95, 0x08, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x62, 0xf4, 0x95, 0x08, 0x80, 0x40 },
 	}, {
 		.pixclk = 30750000,
-		.pll_div_regs = { 0x66, 0xf4, 0x82, 0x01, 0x88, 0x45 },
+		.pll_div_regs = { 0xd1, 0x66, 0xf4, 0x82, 0x01, 0x88, 0x45 },
 	}, {
 		.pixclk = 30888000,
-		.pll_div_regs = { 0x66, 0xf4, 0x99, 0x18, 0x88, 0x45 },
+		.pll_div_regs = { 0xd1, 0x66, 0xf4, 0x99, 0x18, 0x88, 0x45 },
 	}, {
 		.pixclk = 33750000,
-		.pll_div_regs = { 0x70, 0xf4, 0x82, 0x01, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x70, 0xf4, 0x82, 0x01, 0x80, 0x40 },
 	}, {
 		.pixclk = 35000000,
-		.pll_div_regs = { 0x58, 0xb8, 0x8b, 0x88, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x58, 0xb8, 0x8b, 0x88, 0x80, 0x40 },
 	}, {
 		.pixclk = 36000000,
-		.pll_div_regs = { 0x5a, 0xb0, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x5a, 0xb0, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 36036000,
-		.pll_div_regs = { 0x5a, 0xb2, 0xfd, 0x0c, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0xb2, 0xfd, 0x0c, 0x80, 0x40 },
 	}, {
 		.pixclk = 40000000,
-		.pll_div_regs = { 0x64, 0xb0, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x64, 0xb0, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 43200000,
-		.pll_div_regs = { 0x5a, 0x90, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x90, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 43243200,
-		.pll_div_regs = { 0x5a, 0x92, 0xfd, 0x0c, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x92, 0xfd, 0x0c, 0x80, 0x40 },
 	}, {
 		.pixclk = 44500000,
-		.pll_div_regs = { 0x5c, 0x92, 0x98, 0x11, 0x84, 0x41 },
+		.pll_div_regs = { 0xd1, 0x5c, 0x92, 0x98, 0x11, 0x84, 0x41 },
 	}, {
 		.pixclk = 47000000,
-		.pll_div_regs = { 0x62, 0x94, 0x95, 0x82, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x62, 0x94, 0x95, 0x82, 0x80, 0x40 },
 	}, {
 		.pixclk = 47500000,
-		.pll_div_regs = { 0x63, 0x96, 0xa1, 0x82, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x63, 0x96, 0xa1, 0x82, 0x80, 0x40 },
 	}, {
 		.pixclk = 50349650,
-		.pll_div_regs = { 0x54, 0x7c, 0xc3, 0x8f, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x54, 0x7c, 0xc3, 0x8f, 0x80, 0x40 },
 	}, {
 		.pixclk = 50400000,
-		.pll_div_regs = { 0x54, 0x70, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x54, 0x70, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 53250000,
-		.pll_div_regs = { 0x58, 0x72, 0x84, 0x03, 0x82, 0x41 },
+		.pll_div_regs = { 0xd1, 0x58, 0x72, 0x84, 0x03, 0x82, 0x41 },
 	}, {
 		.pixclk = 53500000,
-		.pll_div_regs = { 0x5a, 0x72, 0x89, 0x88, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x72, 0x89, 0x88, 0x80, 0x40 },
 	}, {
 		.pixclk = 54000000,
-		.pll_div_regs = { 0x5a, 0x70, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x70, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 54054000,
-		.pll_div_regs = { 0x5a, 0x72, 0xfd, 0x0c, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x72, 0xfd, 0x0c, 0x80, 0x40 },
 	}, {
 		.pixclk = 59000000,
-		.pll_div_regs = { 0x62, 0x74, 0x95, 0x08, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x62, 0x74, 0x95, 0x08, 0x80, 0x40 },
 	}, {
 		.pixclk = 59340659,
-		.pll_div_regs = { 0x62, 0x74, 0xdb, 0x52, 0x88, 0x47 },
+		.pll_div_regs = { 0xd1, 0x62, 0x74, 0xdb, 0x52, 0x88, 0x47 },
 	}, {
 		.pixclk = 59400000,
-		.pll_div_regs = { 0x63, 0x70, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x63, 0x70, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 61500000,
-		.pll_div_regs = { 0x66, 0x74, 0x82, 0x01, 0x88, 0x45 },
+		.pll_div_regs = { 0xd1, 0x66, 0x74, 0x82, 0x01, 0x88, 0x45 },
 	}, {
 		.pixclk = 63500000,
-		.pll_div_regs = { 0x69, 0x74, 0x89, 0x08, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x69, 0x74, 0x89, 0x08, 0x80, 0x40 },
 	}, {
 		.pixclk = 67500000,
-		.pll_div_regs = { 0x54, 0x52, 0x87, 0x03, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x54, 0x52, 0x87, 0x03, 0x80, 0x40 },
 	}, {
 		.pixclk = 70000000,
-		.pll_div_regs = { 0x58, 0x58, 0x8b, 0x88, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x58, 0x58, 0x8b, 0x88, 0x80, 0x40 },
 	}, {
 		.pixclk = 72000000,
-		.pll_div_regs = { 0x5a, 0x50, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x50, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 72072000,
-		.pll_div_regs = { 0x5a, 0x52, 0xfd, 0x0c, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x52, 0xfd, 0x0c, 0x80, 0x40 },
 	}, {
 		.pixclk = 74176000,
-		.pll_div_regs = { 0x5d, 0x58, 0xdb, 0xA2, 0x88, 0x41 },
+		.pll_div_regs = { 0xd1, 0x5d, 0x58, 0xdb, 0xA2, 0x88, 0x41 },
 	}, {
 		.pixclk = 74250000,
-		.pll_div_regs = { 0x5c, 0x52, 0x90, 0x0d, 0x84, 0x41 },
+		.pll_div_regs = { 0xd1, 0x5c, 0x52, 0x90, 0x0d, 0x84, 0x41 },
 	}, {
 		.pixclk = 78500000,
-		.pll_div_regs = { 0x62, 0x54, 0x87, 0x01, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x62, 0x54, 0x87, 0x01, 0x80, 0x40 },
 	}, {
 		.pixclk = 80000000,
-		.pll_div_regs = { 0x64, 0x50, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x64, 0x50, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 82000000,
-		.pll_div_regs = { 0x66, 0x54, 0x82, 0x01, 0x88, 0x45 },
+		.pll_div_regs = { 0xd1, 0x66, 0x54, 0x82, 0x01, 0x88, 0x45 },
 	}, {
 		.pixclk = 82500000,
-		.pll_div_regs = { 0x67, 0x54, 0x88, 0x01, 0x90, 0x49 },
+		.pll_div_regs = { 0xd1, 0x67, 0x54, 0x88, 0x01, 0x90, 0x49 },
 	}, {
 		.pixclk = 89000000,
-		.pll_div_regs = { 0x70, 0x54, 0x84, 0x83, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x70, 0x54, 0x84, 0x83, 0x80, 0x40 },
 	}, {
 		.pixclk = 90000000,
-		.pll_div_regs = { 0x70, 0x54, 0x82, 0x01, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x70, 0x54, 0x82, 0x01, 0x80, 0x40 },
 	}, {
 		.pixclk = 94000000,
-		.pll_div_regs = { 0x4e, 0x32, 0xa7, 0x10, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x4e, 0x32, 0xa7, 0x10, 0x80, 0x40 },
 	}, {
 		.pixclk = 95000000,
-		.pll_div_regs = { 0x50, 0x31, 0x86, 0x85, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x50, 0x31, 0x86, 0x85, 0x80, 0x40 },
 	}, {
 		.pixclk = 98901099,
-		.pll_div_regs = { 0x52, 0x3a, 0xdb, 0x4c, 0x88, 0x47 },
+		.pll_div_regs = { 0xd1, 0x52, 0x3a, 0xdb, 0x4c, 0x88, 0x47 },
 	}, {
 		.pixclk = 99000000,
-		.pll_div_regs = { 0x52, 0x32, 0x82, 0x01, 0x88, 0x47 },
+		.pll_div_regs = { 0xd1, 0x52, 0x32, 0x82, 0x01, 0x88, 0x47 },
 	}, {
 		.pixclk = 100699300,
-		.pll_div_regs = { 0x54, 0x3c, 0xc3, 0x8f, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x54, 0x3c, 0xc3, 0x8f, 0x80, 0x40 },
 	}, {
 		.pixclk = 100800000,
-		.pll_div_regs = { 0x54, 0x30, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x54, 0x30, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 102500000,
-		.pll_div_regs = { 0x55, 0x32, 0x8c, 0x05, 0x90, 0x4b },
+		.pll_div_regs = { 0xd1, 0x55, 0x32, 0x8c, 0x05, 0x90, 0x4b },
 	}, {
 		.pixclk = 104750000,
-		.pll_div_regs = { 0x57, 0x32, 0x98, 0x07, 0x90, 0x49 },
+		.pll_div_regs = { 0xd1, 0x57, 0x32, 0x98, 0x07, 0x90, 0x49 },
 	}, {
 		.pixclk = 106500000,
-		.pll_div_regs = { 0x58, 0x32, 0x84, 0x03, 0x82, 0x41 },
+		.pll_div_regs = { 0xd1, 0x58, 0x32, 0x84, 0x03, 0x82, 0x41 },
 	}, {
 		.pixclk = 107000000,
-		.pll_div_regs = { 0x5a, 0x32, 0x89, 0x88, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x32, 0x89, 0x88, 0x80, 0x40 },
 	}, {
 		.pixclk = 108000000,
-		.pll_div_regs = { 0x5a, 0x30, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x30, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 108108000,
-		.pll_div_regs = { 0x5a, 0x32, 0xfd, 0x0c, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x32, 0xfd, 0x0c, 0x80, 0x40 },
 	}, {
 		.pixclk = 118000000,
-		.pll_div_regs = { 0x62, 0x34, 0x95, 0x08, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x62, 0x34, 0x95, 0x08, 0x80, 0x40 },
 	}, {
 		.pixclk = 118800000,
-		.pll_div_regs = { 0x63, 0x30, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x63, 0x30, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 123000000,
-		.pll_div_regs = { 0x66, 0x34, 0x82, 0x01, 0x88, 0x45 },
+		.pll_div_regs = { 0xd1, 0x66, 0x34, 0x82, 0x01, 0x88, 0x45 },
 	}, {
 		.pixclk = 127000000,
-		.pll_div_regs = { 0x69, 0x34, 0x89, 0x08, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x69, 0x34, 0x89, 0x08, 0x80, 0x40 },
 	}, {
 		.pixclk = 135000000,
-		.pll_div_regs = { 0x70, 0x34, 0x82, 0x01, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x70, 0x34, 0x82, 0x01, 0x80, 0x40 },
 	}, {
 		.pixclk = 135580000,
-		.pll_div_regs = { 0x71, 0x39, 0xe9, 0x82, 0x9c, 0x5b },
+		.pll_div_regs = { 0xd1, 0x71, 0x39, 0xe9, 0x82, 0x9c, 0x5b },
 	}, {
 		.pixclk = 137520000,
-		.pll_div_regs = { 0x72, 0x38, 0x99, 0x10, 0x85, 0x41 },
+		.pll_div_regs = { 0xd1, 0x72, 0x38, 0x99, 0x10, 0x85, 0x41 },
 	}, {
 		.pixclk = 138750000,
-		.pll_div_regs = { 0x73, 0x35, 0x88, 0x05, 0x90, 0x4d },
+		.pll_div_regs = { 0xd1, 0x73, 0x35, 0x88, 0x05, 0x90, 0x4d },
 	}, {
 		.pixclk = 140000000,
-		.pll_div_regs = { 0x75, 0x36, 0xa7, 0x90, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x75, 0x36, 0xa7, 0x90, 0x80, 0x40 },
 	}, {
 		.pixclk = 144000000,
-		.pll_div_regs = { 0x78, 0x30, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x78, 0x30, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 148352000,
-		.pll_div_regs = { 0x7b, 0x35, 0xdb, 0x39, 0x90, 0x45 },
+		.pll_div_regs = { 0xd1, 0x7b, 0x35, 0xdb, 0x39, 0x90, 0x45 },
 	}, {
 		.pixclk = 148500000,
-		.pll_div_regs = { 0x7b, 0x35, 0x84, 0x03, 0x90, 0x45 },
+		.pll_div_regs = { 0xd1, 0x7b, 0x35, 0x84, 0x03, 0x90, 0x45 },
 	}, {
 		.pixclk = 154000000,
-		.pll_div_regs = { 0x40, 0x18, 0x83, 0x01, 0x00, 0x40 },
+		.pll_div_regs = { 0xd1, 0x40, 0x18, 0x83, 0x01, 0x00, 0x40 },
 	}, {
 		.pixclk = 157000000,
-		.pll_div_regs = { 0x41, 0x11, 0xa7, 0x14, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x41, 0x11, 0xa7, 0x14, 0x80, 0x40 },
 	}, {
 		.pixclk = 160000000,
-		.pll_div_regs = { 0x42, 0x12, 0xa1, 0x20, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x42, 0x12, 0xa1, 0x20, 0x80, 0x40 },
 	}, {
 		.pixclk = 162000000,
-		.pll_div_regs = { 0x43, 0x18, 0x8b, 0x08, 0x96, 0x55 },
+		.pll_div_regs = { 0xd1, 0x43, 0x18, 0x8b, 0x08, 0x96, 0x55 },
 	}, {
 		.pixclk = 164000000,
-		.pll_div_regs = { 0x45, 0x11, 0x83, 0x82, 0x90, 0x4b },
+		.pll_div_regs = { 0xd1, 0x45, 0x11, 0x83, 0x82, 0x90, 0x4b },
 	}, {
 		.pixclk = 165000000,
-		.pll_div_regs = { 0x45, 0x11, 0x84, 0x81, 0x90, 0x4b },
+		.pll_div_regs = { 0xd1, 0x45, 0x11, 0x84, 0x81, 0x90, 0x4b },
 	}, {
 		.pixclk = 180000000,
-		.pll_div_regs = { 0x4b, 0x10, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x4b, 0x10, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 185625000,
-		.pll_div_regs = { 0x4e, 0x12, 0x9a, 0x95, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x4e, 0x12, 0x9a, 0x95, 0x80, 0x40 },
 	}, {
 		.pixclk = 188000000,
-		.pll_div_regs = { 0x4e, 0x12, 0xa7, 0x10, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x4e, 0x12, 0xa7, 0x10, 0x80, 0x40 },
 	}, {
 		.pixclk = 198000000,
-		.pll_div_regs = { 0x52, 0x12, 0x82, 0x01, 0x88, 0x47 },
+		.pll_div_regs = { 0xd1, 0x52, 0x12, 0x82, 0x01, 0x88, 0x47 },
 	}, {
 		.pixclk = 205000000,
-		.pll_div_regs = { 0x55, 0x12, 0x8c, 0x05, 0x90, 0x4b },
+		.pll_div_regs = { 0xd1, 0x55, 0x12, 0x8c, 0x05, 0x90, 0x4b },
 	}, {
 		.pixclk = 209500000,
-		.pll_div_regs = { 0x57, 0x12, 0x98, 0x07, 0x90, 0x49 },
+		.pll_div_regs = { 0xd1, 0x57, 0x12, 0x98, 0x07, 0x90, 0x49 },
 	}, {
 		.pixclk = 213000000,
-		.pll_div_regs = { 0x58, 0x12, 0x84, 0x03, 0x82, 0x41 },
+		.pll_div_regs = { 0xd1, 0x58, 0x12, 0x84, 0x03, 0x82, 0x41 },
 	}, {
 		.pixclk = 216000000,
-		.pll_div_regs = { 0x5a, 0x10, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x10, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 216216000,
-		.pll_div_regs = { 0x5a, 0x12, 0xfd, 0x0c, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x5a, 0x12, 0xfd, 0x0c, 0x80, 0x40 },
 	}, {
 		.pixclk = 237600000,
-		.pll_div_regs = { 0x63, 0x10, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x63, 0x10, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 254000000,
-		.pll_div_regs = { 0x69, 0x14, 0x89, 0x08, 0x80, 0x40 },
+		.pll_div_regs = { 0xd1, 0x69, 0x14, 0x89, 0x08, 0x80, 0x40 },
 	}, {
 		.pixclk = 277500000,
-		.pll_div_regs = { 0x73, 0x15, 0x88, 0x05, 0x90, 0x4d },
+		.pll_div_regs = { 0xd1, 0x73, 0x15, 0x88, 0x05, 0x90, 0x4d },
 	}, {
 		.pixclk = 288000000,
-		.pll_div_regs = { 0x78, 0x10, 0x00, 0x00, 0x80, 0x00 },
+		.pll_div_regs = { 0xd1, 0x78, 0x10, 0x00, 0x00, 0x80, 0x00 },
 	}, {
 		.pixclk = 297000000,
-		.pll_div_regs = { 0x7b, 0x15, 0x84, 0x03, 0x90, 0x45 },
+		.pll_div_regs = { 0xd1, 0x7b, 0x15, 0x84, 0x03, 0x90, 0x45 },
 	},
 };
 
@@ -313,7 +330,8 @@ struct reg_settings {
 };
 
 static const struct reg_settings common_phy_cfg[] = {
-	{ PHY_REG(0), 0x00 }, { PHY_REG(1), 0xd1 },
+	{ PHY_REG(0), 0x00 },
+	/* PHY_REG(1-7) pix clk specific */
 	{ PHY_REG(8), 0x4f }, { PHY_REG(9), 0x30 },
 	{ PHY_REG(10), 0x33 }, { PHY_REG(11), 0x65 },
 	/* REG12 pixclk specific */
@@ -406,6 +424,76 @@ fsl_samsung_hdmi_phy_configure_pll_lock_det(struct fsl_samsung_hdmi_phy *phy,
 	       phy->regs + PHY_REG(14));
 }
 
+static unsigned long fsl_samsung_hdmi_phy_find_pms(unsigned long fout, u8 *p, u16 *m, u8 *s)
+{
+	unsigned long best_freq = 0;
+	u32 min_delta = 0xffffffff;
+	u8 _p, best_p;
+	u16 _m, best_m;
+	u8 _s, best_s;
+
+	/* The ref manual states the values of 'P' range from 1 to 11 */
+	for (_p = 1; _p <= 11; ++_p) {
+		for (_s = 1; _s <= 16; ++_s) {
+			u64 tmp;
+			u32 delta;
+
+			/* s must be one or even */
+			if (_s > 1 && (_s & 0x01) == 1)
+				_s++;
+
+			/* _s cannot be 14 per the TRM */
+			if (_s == 14)
+				continue;
+
+			/*
+			 * TODO: Ref Manual doesn't state the range of _m
+			 * so this should be further refined if possible.
+			 * This range was set based on the original values
+			 * in the look-up table
+			 */
+			tmp = (u64)fout * (_p * _s);
+			do_div(tmp, 24 * MHZ);
+			_m = tmp;
+			if (_m < 0x30 || _m > 0x7b)
+				continue;
+
+			/*
+			 * Rev 2 of the Ref Manual states the
+			 * VCO can range between 750MHz and
+			 * 3GHz.  The VCO is assumed to be _m x
+			 * the reference frequency of 24MHz divided
+			 * by the prescaler, _p
+			 */
+			tmp = (u64)_m * 24 * MHZ;
+			do_div(tmp, _p);
+			if (tmp < 750 * MHZ ||
+			    tmp > 3000 * MHZ)
+				continue;
+
+			tmp = (u64)_m * 24 * MHZ;
+			do_div(tmp, _p * _s);
+
+			delta = abs(fout - tmp);
+			if (delta < min_delta) {
+				best_p = _p;
+				best_s = _s;
+				best_m = _m;
+				min_delta = delta;
+				best_freq = tmp;
+			}
+		}
+	}
+
+	if (best_freq) {
+		*p = best_p;
+		*m = best_m;
+		*s = best_s;
+	}
+
+	return best_freq;
+}
+
 static int fsl_samsung_hdmi_phy_configure(struct fsl_samsung_hdmi_phy *phy,
 					  const struct phy_config *cfg)
 {
@@ -419,13 +507,13 @@ static int fsl_samsung_hdmi_phy_configure(struct fsl_samsung_hdmi_phy *phy,
 	for (i = 0; i < ARRAY_SIZE(common_phy_cfg); i++)
 		writeb(common_phy_cfg[i].val, phy->regs + common_phy_cfg[i].reg);
 
-	/* set individual PLL registers PHY_REG2 ... PHY_REG7 */
+	/* set individual PLL registers PHY_REG1 ... PHY_REG7 */
 	for (i = 0; i < PHY_PLL_DIV_REGS_NUM; i++)
-		writeb(cfg->pll_div_regs[i], phy->regs + PHY_REG(2) + i * 4);
+		writeb(cfg->pll_div_regs[i], phy->regs + PHY_REG(1) + i * 4);
 
-	/* High nibble of pll_div_regs[1] contains S which also gets written to REG21 */
+	/* High nibble of PHY_REG3 and low nibble of PHY_REG21 both contain 'S' */
 	writeb(REG21_SEL_TX_CK_INV | FIELD_PREP(REG21_PMS_S_MASK,
-	       cfg->pll_div_regs[1] >> 4), phy->regs + PHY_REG(21));
+	       cfg->pll_div_regs[2] >> 4), phy->regs + PHY_REG(21));
 
 	fsl_samsung_hdmi_phy_configure_pll_lock_det(phy, cfg);
 
@@ -453,29 +541,70 @@ static unsigned long phy_clk_recalc_rate(struct clk_hw *hw,
 static long phy_clk_round_rate(struct clk_hw *hw,
 			       unsigned long rate, unsigned long *parent_rate)
 {
+	u32 int_div_clk;
 	int i;
+	u16 m;
+	u8 p, s;
+
+	/* If the clock is out of range return error instead of searching */
+	if (rate > 297000000 || rate < 22250000)
+		return -EINVAL;
 
+	/* Check the look-up table */
 	for (i = ARRAY_SIZE(phy_pll_cfg) - 1; i >= 0; i--)
 		if (phy_pll_cfg[i].pixclk <= rate)
-			return phy_pll_cfg[i].pixclk;
+			break;
+	/* If the rate is an exact match, return it now */
+	if (rate == phy_pll_cfg[i].pixclk)
+		return phy_pll_cfg[i].pixclk;
+
+	/*
+	 * The math on the lookup table shows the PMS math yields a
+	 * frequency 5 x pixclk.
+	 * When we check the integer divider against the desired rate,
+	 * multiply the rate x 5 and then divide the outcome by 5.
+	 */
+	int_div_clk = fsl_samsung_hdmi_phy_find_pms(rate * 5, &p, &m, &s) / 5;
 
-	return -EINVAL;
+	/* If the rate is an exact match, return it now */
+	if (int_div_clk == rate)
+		return int_div_clk;
+
+	/* Fall back to the closest value in the LUT */
+	return phy_pll_cfg[i].pixclk;
 }
 
 static int phy_clk_set_rate(struct clk_hw *hw,
 			    unsigned long rate, unsigned long parent_rate)
 {
 	struct fsl_samsung_hdmi_phy *phy = to_fsl_samsung_hdmi_phy(hw);
+	u32 int_div_clk;
 	int i;
-
-	for (i = ARRAY_SIZE(phy_pll_cfg) - 1; i >= 0; i--)
-		if (phy_pll_cfg[i].pixclk <= rate)
-			break;
-
-	if (i < 0)
-		return -EINVAL;
-
-	phy->cur_cfg = &phy_pll_cfg[i];
+	u16 m;
+	u8 p, s;
+
+	/* If the integer divider works, just use it */
+	int_div_clk = fsl_samsung_hdmi_phy_find_pms(rate * 5, &p, &m, &s) / 5;
+	if (int_div_clk == rate) {
+		dev_dbg(phy->dev, "fsl_samsung_hdmi_phy: using integer divider\n");
+		calculated_phy_pll_cfg.pixclk = int_div_clk;
+		calculated_phy_pll_cfg.pll_div_regs[0] = FIELD_PREP(REG01_PMS_P_MASK, p);
+		calculated_phy_pll_cfg.pll_div_regs[1] = m;
+		calculated_phy_pll_cfg.pll_div_regs[2] = FIELD_PREP(REG03_PMS_S_MASK, s-1);
+		/* pll_div_regs 3-6 are fixed and pre-defined already */
+		phy->cur_cfg  = &calculated_phy_pll_cfg;
+	} else {
+		/* Otherwise, search the LUT */
+		dev_dbg(phy->dev, "fsl_samsung_hdmi_phy: using fractional divider\n");
+		for (i = ARRAY_SIZE(phy_pll_cfg) - 1; i >= 0; i--)
+			if (phy_pll_cfg[i].pixclk <= rate)
+				break;
+
+		if (i < 0)
+			return -EINVAL;
+
+		phy->cur_cfg = &phy_pll_cfg[i];
+	}
 
 	return fsl_samsung_hdmi_phy_configure(phy, phy->cur_cfg);
 }
-- 
2.43.0


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

  parent reply	other threads:[~2024-09-03  1:31 UTC|newest]

Thread overview: 11+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-09-03  1:30 [PATCH V4 0/5] phy: freescale: fsl-samsung-hdmi: Expand phy clock options Adam Ford
2024-09-03  1:30 ` [PATCH V4 1/5] phy: freescale: fsl-samsung-hdmi: Replace register defines with macro Adam Ford
2024-09-03  7:47   ` Marco Felsch
2024-09-03  1:30 ` [PATCH V4 2/5] phy: freescale: fsl-samsung-hdmi: Simplify REG21_PMS_S_MASK lookup Adam Ford
2024-09-03  7:57   ` Marco Felsch
2024-09-03  1:30 ` Adam Ford [this message]
2024-09-04  8:28   ` [PATCH V4 3/5] phy: freescale: fsl-samsung-hdmi: Support dynamic integer Dominique Martinet
2024-09-04 10:37     ` Adam Ford
2024-09-03  1:30 ` [PATCH V4 4/5] phy: freescale: fsl-samsung-hdmi: Use closest divider Adam Ford
2024-09-03  5:12   ` Dominique Martinet
2024-09-03  1:30 ` [PATCH V4 5/5] phy: freescale: fsl-samsung-hdmi: Remove unnecessary LUT entries Adam Ford

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20240903013113.139698-4-aford173@gmail.com \
    --to=aford173@gmail.com \
    --cc=Sandor.yu@nxp.com \
    --cc=aford@beaconembedded.com \
    --cc=dominique.martinet@atmark-techno.com \
    --cc=festevam@gmail.com \
    --cc=frieder.schrempf@kontron.de \
    --cc=kishon@kernel.org \
    --cc=l.stach@pengutronix.de \
    --cc=linux-imx@nxp.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-phy@lists.infradead.org \
    --cc=m.felsch@pengutronix.de \
    --cc=u.kleine-koenig@pengutronix.de \
    --cc=vkoul@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).