From: Devarsh Thakkar <devarsht@ti.com>
To: <vkoul@kernel.org>, <kishon@kernel.org>, <mripard@kernel.org>,
<linux-phy@lists.infradead.org>, <linux-kernel@vger.kernel.org>
Cc: <sakari.ailus@linux.intel.com>, <u.kleine-koenig@baylibre.com>,
<vigneshr@ti.com>, <aradhya.bhatia@linux.dev>, <s-jain1@ti.com>,
<r-donadkar@ti.com>, <tomi.valkeinen@ideasonboard.com>,
<devarsht@ti.com>
Subject: [PATCH v3 1/2] phy: cadence: cdns-dphy: Fix PLL lock and O_CMN_READY polling
Date: Fri, 2 May 2025 09:04:50 +0530 [thread overview]
Message-ID: <20250502033451.2291330-2-devarsht@ti.com> (raw)
In-Reply-To: <20250502033451.2291330-1-devarsht@ti.com>
PLL lockup and O_CMN_READY assertion can only happen after common state
machine gets enabled (by programming DPHY_CMN_SSM register), but driver was
polling them before the common state machine was enabled. To fix this :
- Add new function callbacks for polling on PLL lock and O_CMN_READY
assertion.
- As state machine and clocks get enabled in power_on callback only, move
the clock related programming part from configure callback to power_on
callback and poll for the PLL lockup and O_CMN_READY assertion after
state machine gets enabled.
- The configure callback only saves the PLL configuration received from the
client driver which will be applied later on in power_on callback.
- Add checks to ensure configure is called before power_on and state
machine is in disabled state before power_on callback is called.
- Disable state machine in power_off so that client driver can
re-configure the PLL by following up a power_off, configure, power_on
sequence.
Cc: stable@vger.kernel.org
Fixes: 7a343c8bf4b5 ("phy: Add Cadence D-PHY support")
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
---
V3:
- Move out clock programming logic to power_on as PLL polling and enable
can happen only after SSM enable
- Disable state machine on power off
V2:
- Return error code on polling timeout
- Moved out calibration logic to separate patch
drivers/phy/cadence/cdns-dphy.c | 109 +++++++++++++++++++++++++-------
1 file changed, 85 insertions(+), 24 deletions(-)
diff --git a/drivers/phy/cadence/cdns-dphy.c b/drivers/phy/cadence/cdns-dphy.c
index ed87a3970f83..a94109a63788 100644
--- a/drivers/phy/cadence/cdns-dphy.c
+++ b/drivers/phy/cadence/cdns-dphy.c
@@ -79,6 +79,7 @@ struct cdns_dphy_cfg {
u8 pll_ipdiv;
u8 pll_opdiv;
u16 pll_fbdiv;
+ u64 hs_clk_rate;
unsigned int nlanes;
};
@@ -99,6 +100,8 @@ struct cdns_dphy_ops {
void (*set_pll_cfg)(struct cdns_dphy *dphy,
const struct cdns_dphy_cfg *cfg);
unsigned long (*get_wakeup_time_ns)(struct cdns_dphy *dphy);
+ int (*wait_for_pll_lock)(struct cdns_dphy *dphy);
+ int (*wait_for_cmn_ready)(struct cdns_dphy *dphy);
};
struct cdns_dphy {
@@ -108,6 +111,8 @@ struct cdns_dphy {
struct clk *pll_ref_clk;
const struct cdns_dphy_ops *ops;
struct phy *phy;
+ bool is_configured;
+ bool is_powered;
};
/* Order of bands is important since the index is the band number. */
@@ -191,6 +196,26 @@ static unsigned long cdns_dphy_get_wakeup_time_ns(struct cdns_dphy *dphy)
return dphy->ops->get_wakeup_time_ns(dphy);
}
+static int cdns_dphy_wait_for_pll_lock(struct cdns_dphy *dphy)
+{
+ int ret = 0;
+
+ if (dphy->ops->wait_for_pll_lock)
+ ret = dphy->ops->wait_for_pll_lock(dphy);
+
+ return ret;
+}
+
+static int cdns_dphy_wait_for_cmn_ready(struct cdns_dphy *dphy)
+{
+ int ret = 0;
+
+ if (dphy->ops->wait_for_cmn_ready)
+ ret = dphy->ops->wait_for_cmn_ready(dphy);
+
+ return ret;
+}
+
static unsigned long cdns_dphy_ref_get_wakeup_time_ns(struct cdns_dphy *dphy)
{
/* Default wakeup time is 800 ns (in a simulated environment). */
@@ -232,7 +257,6 @@ static unsigned long cdns_dphy_j721e_get_wakeup_time_ns(struct cdns_dphy *dphy)
static void cdns_dphy_j721e_set_pll_cfg(struct cdns_dphy *dphy,
const struct cdns_dphy_cfg *cfg)
{
- u32 status;
/*
* set the PWM and PLL Byteclk divider settings to recommended values
@@ -249,13 +273,6 @@ static void cdns_dphy_j721e_set_pll_cfg(struct cdns_dphy *dphy,
writel(DPHY_TX_J721E_WIZ_LANE_RSTB,
dphy->regs + DPHY_TX_J721E_WIZ_RST_CTRL);
-
- readl_poll_timeout(dphy->regs + DPHY_TX_J721E_WIZ_PLL_CTRL, status,
- (status & DPHY_TX_WIZ_PLL_LOCK), 0, POLL_TIMEOUT_US);
-
- readl_poll_timeout(dphy->regs + DPHY_TX_J721E_WIZ_STATUS, status,
- (status & DPHY_TX_WIZ_O_CMN_READY), 0,
- POLL_TIMEOUT_US);
}
static void cdns_dphy_j721e_set_psm_div(struct cdns_dphy *dphy, u8 div)
@@ -263,6 +280,23 @@ static void cdns_dphy_j721e_set_psm_div(struct cdns_dphy *dphy, u8 div)
writel(div, dphy->regs + DPHY_TX_J721E_WIZ_PSM_FREQ);
}
+static int cdns_dphy_j721e_wait_for_pll_lock(struct cdns_dphy *dphy)
+{
+ u32 status;
+
+ return readl_poll_timeout(dphy->regs + DPHY_TX_J721E_WIZ_PLL_CTRL, status,
+ status & DPHY_TX_WIZ_PLL_LOCK, 0, POLL_TIMEOUT_US);
+}
+
+static int cdns_dphy_j721e_wait_for_cmn_ready(struct cdns_dphy *dphy)
+{
+ u32 status;
+
+ return readl_poll_timeout(dphy->regs + DPHY_TX_J721E_WIZ_STATUS, status,
+ status & DPHY_TX_WIZ_O_CMN_READY, 0,
+ POLL_TIMEOUT_US);
+}
+
/*
* This is the reference implementation of DPHY hooks. Specific integration of
* this IP may have to re-implement some of them depending on how they decided
@@ -278,6 +312,8 @@ static const struct cdns_dphy_ops j721e_dphy_ops = {
.get_wakeup_time_ns = cdns_dphy_j721e_get_wakeup_time_ns,
.set_pll_cfg = cdns_dphy_j721e_set_pll_cfg,
.set_psm_div = cdns_dphy_j721e_set_psm_div,
+ .wait_for_pll_lock = cdns_dphy_j721e_wait_for_pll_lock,
+ .wait_for_cmn_ready = cdns_dphy_j721e_wait_for_cmn_ready,
};
static int cdns_dphy_config_from_opts(struct phy *phy,
@@ -298,6 +334,7 @@ static int cdns_dphy_config_from_opts(struct phy *phy,
return ret;
opts->wakeup = cdns_dphy_get_wakeup_time_ns(dphy) / 1000;
+ cfg->hs_clk_rate = opts->hs_clk_rate;
return 0;
}
@@ -334,13 +371,23 @@ static int cdns_dphy_validate(struct phy *phy, enum phy_mode mode, int submode,
static int cdns_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
{
struct cdns_dphy *dphy = phy_get_drvdata(phy);
- struct cdns_dphy_cfg cfg = { 0 };
- int ret, band_ctrl;
- unsigned int reg;
+ int ret = 0;
- ret = cdns_dphy_config_from_opts(phy, &opts->mipi_dphy, &cfg);
- if (ret)
- return ret;
+ ret = cdns_dphy_config_from_opts(phy, &opts->mipi_dphy, &dphy->cfg);
+ if (!ret)
+ dphy->is_configured = true;
+
+ return ret;
+}
+
+static int cdns_dphy_power_on(struct phy *phy)
+{
+ struct cdns_dphy *dphy = phy_get_drvdata(phy);
+ int ret = 0, band_ctrl;
+ u32 reg;
+
+ if (!dphy->is_configured || dphy->is_powered)
+ return -EINVAL;
/*
* Configure the internal PSM clk divider so that the DPHY has a
@@ -363,9 +410,9 @@ static int cdns_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
* Configure the DPHY PLL that will be used to generate the TX byte
* clk.
*/
- cdns_dphy_set_pll_cfg(dphy, &cfg);
+ cdns_dphy_set_pll_cfg(dphy, &dphy->cfg);
- band_ctrl = cdns_dphy_tx_get_band_ctrl(opts->mipi_dphy.hs_clk_rate);
+ band_ctrl = cdns_dphy_tx_get_band_ctrl(dphy->cfg.hs_clk_rate);
if (band_ctrl < 0)
return band_ctrl;
@@ -373,19 +420,26 @@ static int cdns_dphy_configure(struct phy *phy, union phy_configure_opts *opts)
FIELD_PREP(DPHY_BAND_CFG_RIGHT_BAND, band_ctrl);
writel(reg, dphy->regs + DPHY_BAND_CFG);
- return 0;
-}
+ /* Start TX state machine. */
+ writel(DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
+ dphy->regs + DPHY_CMN_SSM);
-static int cdns_dphy_power_on(struct phy *phy)
-{
- struct cdns_dphy *dphy = phy_get_drvdata(phy);
+ ret = cdns_dphy_wait_for_pll_lock(dphy);
+ if (ret) {
+ dev_err(&dphy->phy->dev, "Failed to lock PLL with err %d\n", ret);
+ return ret;
+ }
+
+ ret = cdns_dphy_wait_for_cmn_ready(dphy);
+ if (ret) {
+ dev_err(&dphy->phy->dev, "O_CMN_READY signal failed to assert with err %d\n", ret);
+ return ret;
+ }
clk_prepare_enable(dphy->psm_clk);
clk_prepare_enable(dphy->pll_ref_clk);
- /* Start TX state machine. */
- writel(DPHY_CMN_SSM_EN | DPHY_CMN_TX_MODE_EN,
- dphy->regs + DPHY_CMN_SSM);
+ dphy->is_powered = true;
return 0;
}
@@ -393,10 +447,17 @@ static int cdns_dphy_power_on(struct phy *phy)
static int cdns_dphy_power_off(struct phy *phy)
{
struct cdns_dphy *dphy = phy_get_drvdata(phy);
+ u32 reg;
clk_disable_unprepare(dphy->pll_ref_clk);
clk_disable_unprepare(dphy->psm_clk);
+ /* Stop TX state machine. */
+ reg = readl(dphy->regs + DPHY_CMN_SSM);
+ writel(reg & ~DPHY_CMN_SSM_EN, dphy->regs + DPHY_CMN_SSM);
+
+ dphy->is_powered = false;
+
return 0;
}
--
2.39.1
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
next prev parent reply other threads:[~2025-05-02 3:35 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2025-05-02 3:34 [PATCH v3 0/2] Fix PLL lock timeout and calibration wait time Devarsh Thakkar
2025-05-02 3:34 ` Devarsh Thakkar [this message]
2025-05-14 10:29 ` [PATCH v3 1/2] phy: cadence: cdns-dphy: Fix PLL lock and O_CMN_READY polling Vinod Koul
2025-06-20 14:41 ` Devarsh Thakkar
2025-05-26 10:59 ` Tomi Valkeinen
2025-06-20 14:35 ` Devarsh Thakkar
2025-06-20 15:08 ` Devarsh Thakkar
2025-06-18 10:01 ` Tomi Valkeinen
2025-06-20 15:07 ` Devarsh Thakkar
2025-05-02 3:34 ` [PATCH v3 2/2] phy: cadence: cdns-dphy: Update calibration wait time for startup state machine Devarsh Thakkar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20250502033451.2291330-2-devarsht@ti.com \
--to=devarsht@ti.com \
--cc=aradhya.bhatia@linux.dev \
--cc=kishon@kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=mripard@kernel.org \
--cc=r-donadkar@ti.com \
--cc=s-jain1@ti.com \
--cc=sakari.ailus@linux.intel.com \
--cc=tomi.valkeinen@ideasonboard.com \
--cc=u.kleine-koenig@baylibre.com \
--cc=vigneshr@ti.com \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).