[PATCH v2 0/2] phy: qcom: edp: Add DP/eDP switch for phys

[PATCH v2 0/2] phy: qcom: edp: Add DP/eDP switch for phys

[Yongxing Mou]

Currently the PHY selects the DP/eDP configuration tables in a fixed way,
choosing the table when enable. This driver has known issues:
1. The selected table does not match the actual platform mode.
2. It cannot support both modes at the same time.

As discussed here[1], this series:
1. Cleans up duplicated and incorrect tables based on the HPG.
2. Fixes the LDO programming error in eDP mode.
3. Adds DP/eDP mode switching support.

Note: x1e80100/sa8775p/sc7280 have been tested, while glymur/sc8280xp
have not been tested.

[1] https://lore.kernel.org/all/20260119-klm_dpphy-v2-1-52252190940b@oss.qualcomm.com/

Signed-off-by: Yongxing Mou <yongxing.mou@oss.qualcomm.com>
---
Changes in v2:
- Combine the third patch with the first one.[Dmitry]
- Fix code formatting issues.[Konrad][Dmitry]
- Update the commit message description.[Dmitry][Konrad]
- Fix kodiak swing/pre_emp table values.[Konrad]
- Link to v1: https://lore.kernel.org/r/20260205-edp_phy-v1-0-231882bbf3f1@oss.qualcomm.com

---
Yongxing Mou (2):
      phy: qcom: edp: Add eDP/DP mode switch support
      phy: qcom: edp: Add per-version LDO configuration callback

 drivers/phy/qualcomm/phy-qcom-edp.c | 176 ++++++++++++++++++++++++++----------
 1 file changed, 129 insertions(+), 47 deletions(-)
---
base-commit: fc4e91c639c0af93d63c3d5bc0ee45515dd7504a
change-id: 20260205-edp_phy-1eca3ed074c0

Best regards,
-- 
Yongxing Mou <yongxing.mou@oss.qualcomm.com>


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 1/2] phy: qcom: edp: Add eDP/DP mode switch support

[Yongxing Mou]

The eDP PHY supports both eDP&DP modes, each requires a different table.
The current driver doesn't fully support every combo PHY mode and use
either the eDP or DP table when enable the platform. In addition, some
platforms mismatch between the mode and the table where DP mode uses
the eDP table or eDP mode use the DP table.

Clean up and correct the tables for currently supported platforms based on
the HPG specification.

Here lists the tables can be reused across current platforms.
DP mode：
	-sa8775p/sc7280/sc8280xp/x1e80100
	-glymur
eDP mode(low vdiff):
	-glymur/sa8775p/sc8280xp/x1e80100
	-sc7280

Cc: stable@vger.kernel.org
Fixes: f199223cb490 ("phy: qcom: Introduce new eDP PHY driver")
Signed-off-by: Yongxing Mou <yongxing.mou@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-edp.c | 90 ++++++++++++++++++++++---------------
 1 file changed, 53 insertions(+), 37 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c
index 13feab99feec..ff14de41cb1c 100644
--- a/drivers/phy/qualcomm/phy-qcom-edp.c
+++ b/drivers/phy/qualcomm/phy-qcom-edp.c
@@ -87,7 +87,8 @@ struct qcom_edp_phy_cfg {
 	bool is_edp;
 	const u8 *aux_cfg;
 	const u8 *vco_div_cfg;
-	const struct qcom_edp_swing_pre_emph_cfg *swing_pre_emph_cfg;
+	const struct qcom_edp_swing_pre_emph_cfg *dp_swing_pre_emph_cfg;
+	const struct qcom_edp_swing_pre_emph_cfg *edp_swing_pre_emph_cfg;
 	const struct phy_ver_ops *ver_ops;
 };
 
@@ -116,17 +117,17 @@ struct qcom_edp {
 };
 
 static const u8 dp_swing_hbr_rbr[4][4] = {
-	{ 0x08, 0x0f, 0x16, 0x1f },
+	{ 0x07, 0x0f, 0x16, 0x1f },
 	{ 0x11, 0x1e, 0x1f, 0xff },
 	{ 0x16, 0x1f, 0xff, 0xff },
 	{ 0x1f, 0xff, 0xff, 0xff }
 };
 
 static const u8 dp_pre_emp_hbr_rbr[4][4] = {
-	{ 0x00, 0x0d, 0x14, 0x1a },
+	{ 0x00, 0x0e, 0x15, 0x1a },
 	{ 0x00, 0x0e, 0x15, 0xff },
 	{ 0x00, 0x0e, 0xff, 0xff },
-	{ 0x03, 0xff, 0xff, 0xff }
+	{ 0x04, 0xff, 0xff, 0xff }
 };
 
 static const u8 dp_swing_hbr2_hbr3[4][4] = {
@@ -150,6 +151,20 @@ static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg = {
 	.pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3,
 };
 
+static const u8 dp_pre_emp_hbr_rbr_v8[4][4] = {
+	{ 0x00, 0x0e, 0x15, 0x1a },
+	{ 0x00, 0x0e, 0x15, 0xff },
+	{ 0x00, 0x0e, 0xff, 0xff },
+	{ 0x00, 0xff, 0xff, 0xff }
+};
+
+static const struct qcom_edp_swing_pre_emph_cfg dp_phy_swing_pre_emph_cfg_v8 = {
+	.swing_hbr_rbr = &dp_swing_hbr_rbr,
+	.swing_hbr3_hbr2 = &dp_swing_hbr2_hbr3,
+	.pre_emphasis_hbr_rbr = &dp_pre_emp_hbr_rbr_v8,
+	.pre_emphasis_hbr3_hbr2 = &dp_pre_emp_hbr2_hbr3,
+};
+
 static const u8 edp_swing_hbr_rbr[4][4] = {
 	{ 0x07, 0x0f, 0x16, 0x1f },
 	{ 0x0d, 0x16, 0x1e, 0xff },
@@ -158,7 +173,7 @@ static const u8 edp_swing_hbr_rbr[4][4] = {
 };
 
 static const u8 edp_pre_emp_hbr_rbr[4][4] = {
-	{ 0x05, 0x12, 0x17, 0x1d },
+	{ 0x05, 0x11, 0x17, 0x1d },
 	{ 0x05, 0x11, 0x18, 0xff },
 	{ 0x06, 0x11, 0xff, 0xff },
 	{ 0x00, 0xff, 0xff, 0xff }
@@ -172,10 +187,10 @@ static const u8 edp_swing_hbr2_hbr3[4][4] = {
 };
 
 static const u8 edp_pre_emp_hbr2_hbr3[4][4] = {
-	{ 0x08, 0x11, 0x17, 0x1b },
-	{ 0x00, 0x0c, 0x13, 0xff },
-	{ 0x05, 0x10, 0xff, 0xff },
-	{ 0x00, 0xff, 0xff, 0xff }
+	{ 0x0c, 0x15, 0x19, 0x1e },
+	{ 0x0b, 0x15, 0x19, 0xff },
+	{ 0x0e, 0x14, 0xff, 0xff },
+	{ 0x0d, 0xff, 0xff, 0xff }
 };
 
 static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg = {
@@ -193,25 +208,25 @@ static const u8 edp_phy_vco_div_cfg_v4[4] = {
 	0x01, 0x01, 0x02, 0x00,
 };
 
-static const u8 edp_pre_emp_hbr_rbr_v5[4][4] = {
-	{ 0x05, 0x11, 0x17, 0x1d },
-	{ 0x05, 0x11, 0x18, 0xff },
-	{ 0x06, 0x11, 0xff, 0xff },
-	{ 0x00, 0xff, 0xff, 0xff }
+static const u8 edp_swing_hbr2_hbr3_v3[4][4] = {
+	{ 0x06, 0x11, 0x16, 0x1b },
+	{ 0x0b, 0x19, 0x1f, 0xff },
+	{ 0x18, 0x1f, 0xff, 0xff },
+	{ 0x1f, 0xff, 0xff, 0xff }
 };
 
-static const u8 edp_pre_emp_hbr2_hbr3_v5[4][4] = {
+static const u8 edp_pre_emp_hbr2_hbr3_v3[4][4] = {
 	{ 0x0c, 0x15, 0x19, 0x1e },
-	{ 0x0b, 0x15, 0x19, 0xff },
-	{ 0x0e, 0x14, 0xff, 0xff },
+	{ 0x09, 0x14, 0x19, 0xff },
+	{ 0x0f, 0x14, 0xff, 0xff },
 	{ 0x0d, 0xff, 0xff, 0xff }
 };
 
-static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v5 = {
+static const struct qcom_edp_swing_pre_emph_cfg edp_phy_swing_pre_emph_cfg_v3 = {
 	.swing_hbr_rbr = &edp_swing_hbr_rbr,
-	.swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3,
-	.pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr_v5,
-	.pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3_v5,
+	.swing_hbr3_hbr2 = &edp_swing_hbr2_hbr3_v3,
+	.pre_emphasis_hbr_rbr = &edp_pre_emp_hbr_rbr,
+	.pre_emphasis_hbr3_hbr2 = &edp_pre_emp_hbr2_hbr3_v3,
 };
 
 static const u8 edp_phy_aux_cfg_v5[DP_AUX_CFG_SIZE] = {
@@ -262,12 +277,7 @@ static int qcom_edp_phy_init(struct phy *phy)
 	       DP_PHY_PD_CTL_PLL_PWRDN | DP_PHY_PD_CTL_DP_CLAMP_EN,
 	       edp->edp + DP_PHY_PD_CTL);
 
-	/*
-	 * TODO: Re-work the conditions around setting the cfg8 value
-	 * when more information becomes available about why this is
-	 * even needed.
-	 */
-	if (edp->cfg->swing_pre_emph_cfg && !edp->is_edp)
+	if (!edp->is_edp)
 		aux_cfg[8] = 0xb7;
 
 	writel(0xfc, edp->edp + DP_PHY_MODE);
@@ -291,7 +301,7 @@ static int qcom_edp_phy_init(struct phy *phy)
 
 static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configure_opts_dp *dp_opts)
 {
-	const struct qcom_edp_swing_pre_emph_cfg *cfg = edp->cfg->swing_pre_emph_cfg;
+	const struct qcom_edp_swing_pre_emph_cfg *cfg;
 	unsigned int v_level = 0;
 	unsigned int p_level = 0;
 	u8 ldo_config;
@@ -299,11 +309,10 @@ static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configur
 	u8 emph;
 	int i;
 
-	if (!cfg)
-		return 0;
-
 	if (edp->is_edp)
-		cfg = &edp_phy_swing_pre_emph_cfg;
+		cfg = edp->cfg->edp_swing_pre_emph_cfg;
+	else
+		cfg = edp->cfg->dp_swing_pre_emph_cfg;
 
 	for (i = 0; i < dp_opts->lanes; i++) {
 		v_level = max(v_level, dp_opts->voltage[i]);
@@ -564,20 +573,24 @@ static const struct qcom_edp_phy_cfg sa8775p_dp_phy_cfg = {
 	.is_edp = false,
 	.aux_cfg = edp_phy_aux_cfg_v5,
 	.vco_div_cfg = edp_phy_vco_div_cfg_v4,
-	.swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v5,
+	.dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
+	.edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg,
 	.ver_ops = &qcom_edp_phy_ops_v4,
 };
 
 static const struct qcom_edp_phy_cfg sc7280_dp_phy_cfg = {
 	.aux_cfg = edp_phy_aux_cfg_v4,
 	.vco_div_cfg = edp_phy_vco_div_cfg_v4,
+	.dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
+	.edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v3,
 	.ver_ops = &qcom_edp_phy_ops_v4,
 };
 
 static const struct qcom_edp_phy_cfg sc8280xp_dp_phy_cfg = {
 	.aux_cfg = edp_phy_aux_cfg_v4,
 	.vco_div_cfg = edp_phy_vco_div_cfg_v4,
-	.swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
+	.dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
+	.edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg,
 	.ver_ops = &qcom_edp_phy_ops_v4,
 };
 
@@ -585,7 +598,8 @@ static const struct qcom_edp_phy_cfg sc8280xp_edp_phy_cfg = {
 	.is_edp = true,
 	.aux_cfg = edp_phy_aux_cfg_v4,
 	.vco_div_cfg = edp_phy_vco_div_cfg_v4,
-	.swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg,
+	.dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
+	.edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg,
 	.ver_ops = &qcom_edp_phy_ops_v4,
 };
 
@@ -765,7 +779,8 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v6 = {
 static struct qcom_edp_phy_cfg x1e80100_phy_cfg = {
 	.aux_cfg = edp_phy_aux_cfg_v4,
 	.vco_div_cfg = edp_phy_vco_div_cfg_v4,
-	.swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
+	.dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
+	.edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg,
 	.ver_ops = &qcom_edp_phy_ops_v6,
 };
 
@@ -944,7 +959,8 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v8 = {
 static struct qcom_edp_phy_cfg glymur_phy_cfg = {
 	.aux_cfg = edp_phy_aux_cfg_v8,
 	.vco_div_cfg = edp_phy_vco_div_cfg_v8,
-	.swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v5,
+	.dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg_v8,
+	.edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg,
 	.ver_ops = &qcom_edp_phy_ops_v8,
 };
 

-- 
2.43.0


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

[PATCH v2 2/2] phy: qcom: edp: Add per-version LDO configuration callback

[Yongxing Mou]

For eDP low Vdiff, the LDO setting depends on the PHY version, instead of
being a simple 0x0 or 0x01. Introduce the com_ldo_config callback to
correct LDO setting accroding to the HPG.

Since SC7280 uses different LDO settings than SA8775P/SC8280XP, introduce
qcom_edp_phy_ops_v3 to keep the LDO setting correct.

Cc: stable@vger.kernel.org
Fixes: f199223cb490 ("phy: qcom: Introduce new eDP PHY driver")
Signed-off-by: Yongxing Mou <yongxing.mou@oss.qualcomm.com>
---
 drivers/phy/qualcomm/phy-qcom-edp.c | 86 ++++++++++++++++++++++++++++++++-----
 1 file changed, 76 insertions(+), 10 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-edp.c b/drivers/phy/qualcomm/phy-qcom-edp.c
index ff14de41cb1c..6464df8d2a62 100644
--- a/drivers/phy/qualcomm/phy-qcom-edp.c
+++ b/drivers/phy/qualcomm/phy-qcom-edp.c
@@ -81,6 +81,7 @@ struct phy_ver_ops {
 	int (*com_clk_fwd_cfg)(const struct qcom_edp *edp);
 	int (*com_configure_pll)(const struct qcom_edp *edp);
 	int (*com_configure_ssc)(const struct qcom_edp *edp);
+	int (*com_ldo_config)(const struct qcom_edp *edp);
 };
 
 struct qcom_edp_phy_cfg {
@@ -304,7 +305,7 @@ static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configur
 	const struct qcom_edp_swing_pre_emph_cfg *cfg;
 	unsigned int v_level = 0;
 	unsigned int p_level = 0;
-	u8 ldo_config;
+	int ret;
 	u8 swing;
 	u8 emph;
 	int i;
@@ -330,13 +331,13 @@ static int qcom_edp_set_voltages(struct qcom_edp *edp, const struct phy_configur
 	if (swing == 0xff || emph == 0xff)
 		return -EINVAL;
 
-	ldo_config = edp->is_edp ? 0x0 : 0x1;
+	ret = edp->cfg->ver_ops->com_ldo_config(edp);
+	if (ret)
+		return ret;
 
-	writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG);
 	writel(swing, edp->tx0 + TXn_TX_DRV_LVL);
 	writel(emph, edp->tx0 + TXn_TX_EMP_POST1_LVL);
 
-	writel(ldo_config, edp->tx1 + TXn_LDO_CONFIG);
 	writel(swing, edp->tx1 + TXn_TX_DRV_LVL);
 	writel(emph, edp->tx1 + TXn_TX_EMP_POST1_LVL);
 
@@ -560,6 +561,52 @@ static int qcom_edp_com_configure_pll_v4(const struct qcom_edp *edp)
 	return 0;
 }
 
+static int qcom_edp_ldo_config_v3(const struct qcom_edp *edp)
+{
+	const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
+	u32 ldo_config;
+
+	if (!edp->is_edp)
+		ldo_config = 0x0;
+	else if (dp_opts->link_rate <= 2700)
+		ldo_config = 0x81;
+	else
+		ldo_config = 0x41;
+
+	writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG);
+	writel(ldo_config, edp->tx1 + TXn_LDO_CONFIG);
+
+	return 0;
+}
+
+static int qcom_edp_ldo_config_v4(const struct qcom_edp *edp)
+{
+	const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
+	u32 ldo_config;
+
+	if (!edp->is_edp)
+		ldo_config = 0x0;
+	else if (dp_opts->link_rate <= 2700)
+		ldo_config = 0xc1;
+	else
+		ldo_config = 0x81;
+
+	writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG);
+	writel(ldo_config, edp->tx1 + TXn_LDO_CONFIG);
+
+	return 0;
+}
+
+static const struct phy_ver_ops qcom_edp_phy_ops_v3 = {
+	.com_power_on		= qcom_edp_phy_power_on_v4,
+	.com_resetsm_cntrl	= qcom_edp_phy_com_resetsm_cntrl_v4,
+	.com_bias_en_clkbuflr	= qcom_edp_com_bias_en_clkbuflr_v4,
+	.com_clk_fwd_cfg	= qcom_edp_com_clk_fwd_cfg_v4,
+	.com_configure_pll	= qcom_edp_com_configure_pll_v4,
+	.com_configure_ssc	= qcom_edp_com_configure_ssc_v4,
+	.com_ldo_config		= qcom_edp_ldo_config_v3,
+};
+
 static const struct phy_ver_ops qcom_edp_phy_ops_v4 = {
 	.com_power_on		= qcom_edp_phy_power_on_v4,
 	.com_resetsm_cntrl	= qcom_edp_phy_com_resetsm_cntrl_v4,
@@ -567,6 +614,7 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v4 = {
 	.com_clk_fwd_cfg	= qcom_edp_com_clk_fwd_cfg_v4,
 	.com_configure_pll	= qcom_edp_com_configure_pll_v4,
 	.com_configure_ssc	= qcom_edp_com_configure_ssc_v4,
+	.com_ldo_config		= qcom_edp_ldo_config_v4,
 };
 
 static const struct qcom_edp_phy_cfg sa8775p_dp_phy_cfg = {
@@ -583,7 +631,7 @@ static const struct qcom_edp_phy_cfg sc7280_dp_phy_cfg = {
 	.vco_div_cfg = edp_phy_vco_div_cfg_v4,
 	.dp_swing_pre_emph_cfg = &dp_phy_swing_pre_emph_cfg,
 	.edp_swing_pre_emph_cfg = &edp_phy_swing_pre_emph_cfg_v3,
-	.ver_ops = &qcom_edp_phy_ops_v4,
+	.ver_ops = &qcom_edp_phy_ops_v3,
 };
 
 static const struct qcom_edp_phy_cfg sc8280xp_dp_phy_cfg = {
@@ -768,12 +816,31 @@ static int qcom_edp_com_configure_pll_v6(const struct qcom_edp *edp)
 	return 0;
 }
 
+static int qcom_edp_ldo_config_v6(const struct qcom_edp *edp)
+{
+	const struct phy_configure_opts_dp *dp_opts = &edp->dp_opts;
+	u32 ldo_config;
+
+	if (!edp->is_edp)
+		ldo_config = 0x0;
+	else if (dp_opts->link_rate <= 2700)
+		ldo_config = 0x51;
+	else
+		ldo_config = 0x91;
+
+	writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG);
+	writel(ldo_config, edp->tx1 + TXn_LDO_CONFIG);
+
+	return 0;
+}
+
 static const struct phy_ver_ops qcom_edp_phy_ops_v6 = {
 	.com_power_on		= qcom_edp_phy_power_on_v6,
 	.com_resetsm_cntrl	= qcom_edp_phy_com_resetsm_cntrl_v6,
 	.com_bias_en_clkbuflr	= qcom_edp_com_bias_en_clkbuflr_v6,
 	.com_configure_pll	= qcom_edp_com_configure_pll_v6,
 	.com_configure_ssc	= qcom_edp_com_configure_ssc_v6,
+	.com_ldo_config		= qcom_edp_ldo_config_v6,
 };
 
 static struct qcom_edp_phy_cfg x1e80100_phy_cfg = {
@@ -954,6 +1021,7 @@ static const struct phy_ver_ops qcom_edp_phy_ops_v8 = {
 	.com_clk_fwd_cfg	= qcom_edp_com_clk_fwd_cfg_v8,
 	.com_configure_pll	= qcom_edp_com_configure_pll_v8,
 	.com_configure_ssc	= qcom_edp_com_configure_ssc_v8,
+	.com_ldo_config		= qcom_edp_ldo_config_v6,
 };
 
 static struct qcom_edp_phy_cfg glymur_phy_cfg = {
@@ -969,7 +1037,6 @@ static int qcom_edp_phy_power_on(struct phy *phy)
 	const struct qcom_edp *edp = phy_get_drvdata(phy);
 	u32 bias0_en, drvr0_en, bias1_en, drvr1_en;
 	unsigned long pixel_freq;
-	u8 ldo_config = 0x0;
 	int ret;
 	u32 val;
 	u8 cfg1;
@@ -978,11 +1045,10 @@ static int qcom_edp_phy_power_on(struct phy *phy)
 	if (ret)
 		return ret;
 
-	if (edp->cfg->swing_pre_emph_cfg && !edp->is_edp)
-		ldo_config = 0x1;
+	ret = edp->cfg->ver_ops->com_ldo_config(edp);
+	if (ret)
+		return ret;
 
-	writel(ldo_config, edp->tx0 + TXn_LDO_CONFIG);
-	writel(ldo_config, edp->tx1 + TXn_LDO_CONFIG);
 	writel(0x00, edp->tx0 + TXn_LANE_MODE_1);
 	writel(0x00, edp->tx1 + TXn_LANE_MODE_1);
 

-- 
2.43.0


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 0/2] phy: qcom: edp: Add DP/eDP switch for phys

[Dmitry Baryshkov]

On Fri, Feb 13, 2026 at 03:31:41PM +0800, Yongxing Mou wrote:
> Currently the PHY selects the DP/eDP configuration tables in a fixed way,
> choosing the table when enable. This driver has known issues:
> 1. The selected table does not match the actual platform mode.
> 2. It cannot support both modes at the same time.
> 
> As discussed here[1], this series:
> 1. Cleans up duplicated and incorrect tables based on the HPG.
> 2. Fixes the LDO programming error in eDP mode.
> 3. Adds DP/eDP mode switching support.
> 
> Note: x1e80100/sa8775p/sc7280 have been tested, while glymur/sc8280xp
> have not been tested.
> 
> [1] https://lore.kernel.org/all/20260119-klm_dpphy-v2-1-52252190940b@oss.qualcomm.com/
> 
> Signed-off-by: Yongxing Mou <yongxing.mou@oss.qualcomm.com>
> ---
> Changes in v2:
> - Combine the third patch with the first one.[Dmitry]
> - Fix code formatting issues.[Konrad][Dmitry]
> - Update the commit message description.[Dmitry][Konrad]
> - Fix kodiak swing/pre_emp table values.[Konrad]
> - Link to v1: https://lore.kernel.org/r/20260205-edp_phy-v1-0-231882bbf3f1@oss.qualcomm.com
> 
> ---
> Yongxing Mou (2):
>       phy: qcom: edp: Add eDP/DP mode switch support
>       phy: qcom: edp: Add per-version LDO configuration callback
> 
>  drivers/phy/qualcomm/phy-qcom-edp.c | 176 ++++++++++++++++++++++++++----------
>  1 file changed, 129 insertions(+), 47 deletions(-)
> ---
> base-commit: fc4e91c639c0af93d63c3d5bc0ee45515dd7504a

20260108 is very old. Your second patch doesn't apply anymore.

> change-id: 20260205-edp_phy-1eca3ed074c0
> 
> Best regards,
> -- 
> Yongxing Mou <yongxing.mou@oss.qualcomm.com>
> 

-- 
With best wishes
Dmitry

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy

Re: [PATCH v2 0/2] phy: qcom: edp: Add DP/eDP switch for phys

[Yongxing Mou]

On 2/14/2026 12:12 AM, Dmitry Baryshkov wrote:
> On Fri, Feb 13, 2026 at 03:31:41PM +0800, Yongxing Mou wrote:
>> Currently the PHY selects the DP/eDP configuration tables in a fixed way,
>> choosing the table when enable. This driver has known issues:
>> 1. The selected table does not match the actual platform mode.
>> 2. It cannot support both modes at the same time.
>>
>> As discussed here[1], this series:
>> 1. Cleans up duplicated and incorrect tables based on the HPG.
>> 2. Fixes the LDO programming error in eDP mode.
>> 3. Adds DP/eDP mode switching support.
>>
>> Note: x1e80100/sa8775p/sc7280 have been tested, while glymur/sc8280xp
>> have not been tested.
>>
>> [1] https://lore.kernel.org/all/20260119-klm_dpphy-v2-1-52252190940b@oss.qualcomm.com/
>>
>> Signed-off-by: Yongxing Mou <yongxing.mou@oss.qualcomm.com>
>> ---
>> Changes in v2:
>> - Combine the third patch with the first one.[Dmitry]
>> - Fix code formatting issues.[Konrad][Dmitry]
>> - Update the commit message description.[Dmitry][Konrad]
>> - Fix kodiak swing/pre_emp table values.[Konrad]
>> - Link to v1: https://lore.kernel.org/r/20260205-edp_phy-v1-0-231882bbf3f1@oss.qualcomm.com
>>
>> ---
>> Yongxing Mou (2):
>>        phy: qcom: edp: Add eDP/DP mode switch support
>>        phy: qcom: edp: Add per-version LDO configuration callback
>>
>>   drivers/phy/qualcomm/phy-qcom-edp.c | 176 ++++++++++++++++++++++++++----------
>>   1 file changed, 129 insertions(+), 47 deletions(-)
>> ---
>> base-commit: fc4e91c639c0af93d63c3d5bc0ee45515dd7504a
> 
> 20260108 is very old. Your second patch doesn't apply anymore.
> 
Thanks. Got it, will update to latest tag in next patch.
>> change-id: 20260205-edp_phy-1eca3ed074c0
>>
>> Best regards,
>> -- 
>> Yongxing Mou <yongxing.mou@oss.qualcomm.com>
>>
> 


-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy