Re: [PATCH 3/7] phy: qcom-qmp-combo: Introduce orientation variable

From: Johan Hovold <johan@kernel.org>
To: Bjorn Andersson <quic_bjorande@quicinc.com>
Cc: Vinod Koul <vkoul@kernel.org>,
	Kishon Vijay Abraham I <kishon@kernel.org>,
	Bjorn Andersson <andersson@kernel.org>,
	Konrad Dybcio <konrad.dybcio@linaro.org>,
	Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	linux-arm-msm@vger.kernel.org, linux-phy@lists.infradead.org,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 3/7] phy: qcom-qmp-combo: Introduce orientation variable
Date: Tue, 2 May 2023 13:48:16 +0200	[thread overview]
Message-ID: <ZFD4gM9dUQwBmSUe@hovoldconsulting.com> (raw)
In-Reply-To: <20230425034010.3789376-4-quic_bjorande@quicinc.com>

On Mon, Apr 24, 2023 at 08:40:06PM -0700, Bjorn Andersson wrote:
> In multiple places throughout the driver code has been written in
> prepration for handling of orientation switching.
> 
> Introduce a typec_orientation in qmp_combo and fill out the various
> "placeholders" with the associated logic. By initializing the
> orientation to "normal" this change has no functional impact, but
> reduces the size of the upcoming introduction of dynamic orientation
> switching.
> 
> Signed-off-by: Bjorn Andersson <quic_bjorande@quicinc.com>
> ---
>  drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 54 +++++++++++++----------
>  1 file changed, 30 insertions(+), 24 deletions(-)
> 
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> index 7280f7141961..6748f31da7a3 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
> @@ -19,6 +19,7 @@
>  #include <linux/regulator/consumer.h>
>  #include <linux/reset.h>
>  #include <linux/slab.h>
> +#include <linux/usb/typec.h>
>  
>  #include <dt-bindings/phy/phy-qcom-qmp.h>
>  
> @@ -63,6 +64,10 @@
>  /* QPHY_V3_PCS_MISC_CLAMP_ENABLE register bits */
>  #define CLAMP_EN				BIT(0) /* enables i/o clamp_n */
>  
> +/* QPHY_V3_DP_COM_TYPEC_CTRL register bits */
> +#define SW_PORTSELECT_VAL			BIT(0)
> +#define SW_PORTSELECT_MUX			BIT(1)
> +
>  #define PHY_INIT_COMPLETE_TIMEOUT		10000
>  
>  struct qmp_phy_init_tbl {
> @@ -1323,6 +1328,8 @@ struct qmp_combo {
>  	struct clk_fixed_rate pipe_clk_fixed;
>  	struct clk_hw dp_link_hw;
>  	struct clk_hw dp_pixel_hw;
> +
> +	enum typec_orientation orientation;
>  };
>  
>  static void qmp_v3_dp_aux_init(struct qmp_combo *qmp);
> @@ -1955,29 +1962,23 @@ static void qmp_v3_configure_dp_tx(struct qmp_combo *qmp)
>  static bool qmp_combo_configure_dp_mode(struct qmp_combo *qmp)
>  {
>  	u32 val;
> -	bool reverse = false;
> +	bool reverse = qmp->orientation == TYPEC_ORIENTATION_REVERSE;

Adding parentheses around the right-hand side should make this a little
easier to parse.

It also looks like these callbacks end up being called without holding
the qmp->phy_mutex via phy->power_on(). Perhaps there is no risk for a
concurrent switch notification and dp phy power-on but it's not that
obvious.

> +	const struct phy_configure_opts_dp *dp_opts = &qmp->dp_opts;

Also could you add these before u32 val to maintain an approximation of
reverse xmas style?

And similar below.

Johan

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy