Re: [PATCH net] net: macb: In ZynqMP resume always configure PS GTR for non-wakeup source

Re: [PATCH net] net: macb: In ZynqMP resume always configure PS GTR for non-wakeup source

[Russell King (Oracle)]

On Wed, Aug 09, 2023 at 03:41:21PM -0700, Jakub Kicinski wrote:
> On Mon, 7 Aug 2023 18:44:51 +0530 Radhey Shyam Pandey wrote:
> > On Zynq UltraScale+ MPSoC ubuntu platform when systemctl issues suspend,
> > network manager bring down the interface and goes into suspend. When it
> > wakes up it again enables the interface.
> > 
> > This leads to xilinx-psgtr "PLL lock timeout" on interface bringup, as
> > the power management controller power down the entire FPD (including
> > SERDES) if none of the FPD devices are in use and serdes is not
> > initialized on resume.
> > 
> > $ sudo rtcwake -m no -s 120 -v
> > $ sudo systemctl suspend  <this does ifconfig eth1 down>
> > $ ifconfig eth1 up
> > xilinx-psgtr fd400000.phy: lane 0 (type 10, protocol 5): PLL lock timeout
> > phy phy-fd400000.phy.0: phy poweron failed --> -110
> > 
> > macb driver is called in this way:
> > 1. macb_close: Stop network interface. In this function, it
> >    reset MACB IP and disables PHY and network interface.
> > 
> > 2. macb_suspend: It is called in kernel suspend flow. But because
> >    network interface has been disabled(netif_running(ndev) is
> >    false), it does nothing and returns directly;
> > 
> > 3. System goes into suspend state. Some time later, system is
> >    waken up by RTC wakeup device;
> > 
> > 4. macb_resume: It does nothing because network interface has
> >    been disabled;
> > 
> > 5. macb_open: It is called to enable network interface again. ethernet
> >    interface is initialized in this API but serdes which is power-off
> >    by PMUFW during FPD-off suspend is not initialized again and so
> >    we hit GT PLL lock issue on open.
> > 
> > To resolve this PLL timeout issue always do PS GTR initialization
> > when ethernet device is configured as non-wakeup source.
> > 
> > Fixes: f22bd29ba19a ("net: macb: Fix ZynqMP SGMII non-wakeup source resume failure")
> > Fixes: 8b73fa3ae02b ("net: macb: Added ZynqMP-specific initialization")
> > Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
> 
> Could be more of a PHY than MAC question. Adding remaining PHY
> maintainers to CC.

This is not ethernet PHY stuff (drivers/net/phy), it's serdes PHY
(drivers/phy). Their requirements vary a lot.

Given the above description...

In (1), phy_power_off() gets called. If this is actually done by
the serdes PHY driver, then the clocks from the serdes PHY stop.

Whether the PHY is re-initialised or not during the suspend/resume
should not affect it - we haven't asked for it to be powered up
again.

So in (5), I assume that the problem occurs because macb_init_hw()
is called before phy_power_on()... but what do I know... with these
randomly generated abbreviations that are designed to exclude people
from understanding what is going on which seem to be common in the
computing world. FPD? GT? Shrug, utterly meaningless.

However, surely phy_init() while the PHY is supposed to be powered
off should fail? Don't know, this is outside of my area of knowledge.
Adding generic phy maintainers and list...

-- 
RMK's Patch system: https://www.armlinux.org.uk/developer/patches/
FTTP is here! 80Mbps down 10Mbps up. Decent connectivity at last!

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy