From: Nitin Rawat <quic_nitirawa@quicinc.com>
To: Vinod Koul <vkoul@kernel.org>
Cc: <agross@kernel.org>, <andersson@kernel.org>,
<konrad.dybcio@linaro.org>, <kishon@kernel.org>,
<robh+dt@kernel.org>, <krzysztof.kozlowski+dt@linaro.org>,
<conor+dt@kernel.org>, <linux-arm-msm@vger.kernel.org>,
<linux-phy@lists.infradead.org>, <linux-kernel@vger.kernel.org>,
<devicetree@vger.kernel.org>,
Manish Pandey <quic_mapa@quicinc.com>
Subject: Re: [PATCH V2 2/2] phy: qcom-qmp-ufs: Add Phy Configuration support for SC7280
Date: Tue, 22 Aug 2023 21:08:44 +0530 [thread overview]
Message-ID: <b970ccf1-e4e2-0d79-aeb2-a1b612cc1b10@quicinc.com> (raw)
In-Reply-To: <ZOTBYz34rVfYWouh@matsya>
On 8/22/2023 7:38 PM, Vinod Koul wrote:
> On 19-08-23, 17:22, Nitin Rawat wrote:
>> Add SC7280 specific register layout and table configs.
>>
>> Co-developed-by: Manish Pandey <quic_mapa@quicinc.com>
>> Signed-off-by: Manish Pandey <quic_mapa@quicinc.com>
>> Signed-off-by: Nitin Rawat <quic_nitirawa@quicinc.com>
>> ---
>> drivers/phy/qualcomm/phy-qcom-qmp-ufs.c | 142 ++++++++++++++++++++++++
>> 1 file changed, 142 insertions(+)
>>
>> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> index 3927eba8e468..b22198d09508 100644
>> --- a/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> +++ b/drivers/phy/qualcomm/phy-qcom-qmp-ufs.c
>> @@ -177,6 +177,111 @@ static const struct qmp_phy_init_tbl msm8996_ufsphy_rx[] = {
>> QMP_PHY_INIT_CFG(QSERDES_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0E),
>> };
>>
>> +static const struct qmp_phy_init_tbl sc7280_ufsphy_tx[] = {
>> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_1_DIVIDER_BAND0_1, 0x06),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_2_DIVIDER_BAND0_1, 0x03),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_3_DIVIDER_BAND0_1, 0x01),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_PWM_GEAR_4_DIVIDER_BAND0_1, 0x00),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0x35),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_TX_TRAN_DRVR_EMP_EN, 0x0c),
>> +};
>> +
>> +static const struct qmp_phy_init_tbl sc7280_ufsphy_rx[] = {
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_LVL, 0x24),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x0f),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x1e),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_BAND, 0x18),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x0a),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5a),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0xf1),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CTRL2, 0x80),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0e),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_TERM_BW, 0x1b),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x06),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x04),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x1d),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_MEASURE_TIME, 0x10),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x6d),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0x6d),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xed),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x3b),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x3c),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0xe0),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xc8),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xc8),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x3b),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0xb1),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_LOW, 0xe0),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH, 0xc8),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH2, 0xc8),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH3, 0x3b),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH4, 0xb1),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
>> +};
>> +
>> +static const struct qmp_phy_init_tbl sc7280_ufsphy_pcs[] = {
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_SIGDET_CTRL2, 0x6D),
>
> Lower case please (here and few other places)
>
Sure , I'll update this in my next patchset.
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_LARGE_AMP_DRV_LVL, 0x0A),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_SMALL_AMP_DRV_LVL, 0x02),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_MID_TERM_CTRL1, 0x43),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_DEBUG_BUS_CLKSEL, 0x1F),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_MIN_HIBERN8_TIME, 0xFF),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_MULTI_LANE_CTRL1, 0x02),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_PLL_CNTL, 0x03),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TIMER_20US_CORECLK_STEPS_MSB, 0x16),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TIMER_20US_CORECLK_STEPS_LSB, 0xD8),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_PWM_GEAR_BAND, 0xAA),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_HS_GEAR_BAND, 0x06),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_TX_HSGEAR_CAPABILITY, 0x03),
>> + QMP_PHY_INIT_CFG(QPHY_V4_PCS_UFS_RX_HSGEAR_CAPABILITY, 0x03),
>> +};
>> +
>> +static const struct qmp_phy_init_tbl sc7280_ufsphy_hs_g4_rx[] = {
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_LVL, 0x24),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x0f),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x1e),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_BAND, 0x18),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_FO_GAIN, 0x0a),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x5a),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0xf1),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FASTLOCK_COUNT_LOW, 0x80),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CTRL2, 0x81),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0e),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x04),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_TERM_BW, 0x6f),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL1, 0x04),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x00),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x09),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x07),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x17),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2, 0x00),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_MEASURE_TIME, 0x20),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0x80),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x01),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x3f),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH, 0xff),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xff),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x2c),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0x6d),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0x6d),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xed),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x3b),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0x3c),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_LOW, 0xe0),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH, 0xc8),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH2, 0xc8),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH3, 0x3b),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH4, 0xb1),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
>> + QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x0f),
>> +};
>> +
>> static const struct qmp_phy_init_tbl sm6115_ufsphy_serdes[] = {
>> QMP_PHY_INIT_CFG(QSERDES_COM_CMN_CONFIG, 0x0e),
>> QMP_PHY_INIT_CFG(QSERDES_COM_SYSCLK_EN_SEL, 0x14),
>> @@ -888,6 +993,40 @@ static const struct qmp_phy_cfg sa8775p_ufsphy_cfg = {
>> .regs = ufsphy_v5_regs_layout,
>> };
>>
>> +static const struct qmp_phy_cfg sc7280_ufsphy_cfg = {
>
> sorted alphabetically please
Sorry vinod. I didnt completely understood the comment.
I see sc7280_ufsphy_cfg is after sa8775p_ufsphy_cfg and before
sc8280xp_ufsphy_cfg , so it seems to be sorted.
Am i missing anything here?
Regards,
Nitin
>
>> + .lanes = 2,
>> +
>> + .offsets = &qmp_ufs_offsets,
>> +
>> + .tbls = {
>> + .serdes = sm8150_ufsphy_serdes,
>> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_serdes),
>> + .tx = sc7280_ufsphy_tx,
>> + .tx_num = ARRAY_SIZE(sc7280_ufsphy_tx),
>> + .rx = sc7280_ufsphy_rx,
>> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_rx),
>> + .pcs = sc7280_ufsphy_pcs,
>> + .pcs_num = ARRAY_SIZE(sc7280_ufsphy_pcs),
>> + },
>> + .tbls_hs_b = {
>> + .serdes = sm8150_ufsphy_hs_b_serdes,
>> + .serdes_num = ARRAY_SIZE(sm8150_ufsphy_hs_b_serdes),
>> + },
>> + .tbls_hs_g4 = {
>> + .tx = sm8250_ufsphy_hs_g4_tx,
>> + .tx_num = ARRAY_SIZE(sm8250_ufsphy_hs_g4_tx),
>> + .rx = sc7280_ufsphy_hs_g4_rx,
>> + .rx_num = ARRAY_SIZE(sc7280_ufsphy_hs_g4_rx),
>> + .pcs = sm8150_ufsphy_hs_g4_pcs,
>> + .pcs_num = ARRAY_SIZE(sm8150_ufsphy_hs_g4_pcs),
>> + },
>> + .clk_list = sm8450_ufs_phy_clk_l,
>> + .num_clks = ARRAY_SIZE(sm8450_ufs_phy_clk_l),
>> + .vreg_list = qmp_phy_vreg_l,
>> + .num_vregs = ARRAY_SIZE(qmp_phy_vreg_l),
>> + .regs = ufsphy_v4_regs_layout,
>> +};
>> +
>> static const struct qmp_phy_cfg sc8280xp_ufsphy_cfg = {
>> .lanes = 2,
>>
>> @@ -1648,6 +1787,9 @@ static const struct of_device_id qmp_ufs_of_match_table[] = {
>> }, {
>> .compatible = "qcom,sa8775p-qmp-ufs-phy",
>> .data = &sa8775p_ufsphy_cfg,
>> + }, {
>> + .compatible = "qcom,sc7280-qmp-ufs-phy",
>> + .data = &sc7280_ufsphy_cfg,
>> }, {
>> .compatible = "qcom,sc8180x-qmp-ufs-phy",
>> .data = &sm8150_ufsphy_cfg,
>> --
>> 2.17.1
>
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
prev parent reply other threads:[~2023-08-22 15:39 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-19 11:52 [PATCH V2 0/2] Add Phy Configuration support for SC7280 Nitin Rawat
2023-08-19 11:52 ` [PATCH V2 1/2] dt-bindings: phy: Add QMP UFS PHY comptible " Nitin Rawat
2023-08-19 12:44 ` Krzysztof Kozlowski
2023-08-19 11:52 ` [PATCH V2 2/2] phy: qcom-qmp-ufs: Add Phy Configuration support " Nitin Rawat
2023-08-22 14:08 ` Vinod Koul
2023-08-22 15:38 ` Nitin Rawat [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=b970ccf1-e4e2-0d79-aeb2-a1b612cc1b10@quicinc.com \
--to=quic_nitirawa@quicinc.com \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=kishon@kernel.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=quic_mapa@quicinc.com \
--cc=robh+dt@kernel.org \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox