Re: [PATCH RFC 13/13] riscv: dts: starfive: jh7110: Update DT for display subsystem

[Icenowy Zheng <uwu@icenowy.me>]

在 2025-11-08星期六的 02:04 +0100，Michal Wilczynski写道：
> Activate the display subsystem drivers by refactoring the device
> tree.
> 
> This change wraps the dc8200, hdmi, and voutcrg nodes within the new
> vout_subsystem node. This ensures the PD_VOUT power domain is enabled
> before the child drivers are probed.

Well a problem exist that some display muxes exist in the vout syscon.

Maybe this should be modelled in the device tree two?

> 
> The monolithic hdmi node is replaced with the hdmi_mfd (MFD parent)
> node, containing the hdmi_phy and hdmi_controller children.
> 
> The voutcrg node is updated to consume the pixel clock from the
> &hdmi_phy node instead of the old fixed-clock. The dc8200 node is
> also
> updated to get its pixel clocks from voutcrg's MUXes.
> 
> Finally, the old, incorrect hdmitx0-pixel-clock fixed-clock node is
> removed.
> 
> Signed-off-by: Michal Wilczynski <m.wilczynski@samsung.com>
> ---
>  arch/riscv/boot/dts/starfive/jh7110-common.dtsi | 119
> +++++++++++++++++++++++-
>  arch/riscv/boot/dts/starfive/jh7110.dtsi        | 111
> +++++++++++++++++-----
>  2 files changed, 207 insertions(+), 23 deletions(-)
> 
> diff --git a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> index
> 2eaf01775ef57d884b4d662af3caa83da2d2ad48..ce459e297261393a35206170704
> 1db453819885c 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110-common.dtsi
> @@ -33,6 +33,25 @@ memory@40000000 {
>                 bootph-pre-ram;
>         };
>  
> +       reserved-memory {
> +               #address-cells = <2>;
> +               #size-cells = <2>;
> +               ranges;
> +
> +               /* vout applies for space from this CMA
> +                * Without this CMA reservation,
> +                * vout may not work properly.
> +                */
> +               linux,cma {
> +                       compatible = "shared-dma-pool";
> +                       reusable;
> +                       size = <0x0 0x20000000>;
> +                       alignment = <0x0 0x1000>;
> +                       alloc-ranges = <0x0 0x70000000 0x0
> 0x20000000>;
> +                       linux,cma-default;
> +               };
> +       };
> +
>         gpio-restart {
>                 compatible = "gpio-restart";
>                 gpios = <&sysgpio 35 GPIO_ACTIVE_HIGH>;
> @@ -73,12 +92,47 @@ codec {
>                         };
>                 };
>         };
> +
> +       hdmi-connector {
> +               compatible = "hdmi-connector";
> +               type = "a";
> +
> +               port {
> +                       hdmi_con_in: endpoint {
> +                               remote-endpoint = <&hdmi_out_con>;
> +                       };
> +               };
> +       };
>  };
>  
>  &cpus {
>         timebase-frequency = <4000000>;
>  };
>  
> +&dc8200 {
> +       status = "okay";
> +
> +       ports {
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               dpu_port0: port@0 {
> +                       reg = <0>;
> +                       #address-cells = <1>;
> +                       #size-cells = <0>;
> +
> +                       dpu_out_dpi0: endpoint@0 {
> +                               reg = <0>;
> +                               remote-endpoint = <&hdmi_in>;
> +                       };
> +               };
> +
> +               dpu_port1: port@1 {
> +                       reg = <1>;
> +               };
> +       };
> +};
> +
>  &dvp_clk {
>         clock-frequency = <74250000>;
>  };
> @@ -99,8 +153,31 @@ &gmac1_rmii_refin {
>         clock-frequency = <50000000>;
>  };
>  
> -&hdmitx0_pixelclk {
> -       clock-frequency = <297000000>;
> +&hdmi_controller {
> +       status = "okay";
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&hdmi_pins>;
> +
> +       ports {
> +               #address-cells = <1>;
> +               #size-cells = <0>;
> +
> +               port@0 {
> +                       reg = <0>;
> +
> +                       hdmi_in: endpoint {
> +                               remote-endpoint = <&dpu_out_dpi0>;
> +                       };
> +               };
> +
> +               hdmi_out_port: port@1 {
> +                       reg = <1>;
> +                       hdmi_out_con: endpoint {
> +                               remote-endpoint = <&hdmi_con_in>;
> +                       };
> +
> +               };
> +       };
>  };
>  
>  &i2srx_bclk_ext {
> @@ -388,6 +465,40 @@ &syscrg {
>  };
>  
>  &sysgpio {
> +       hdmi_pins: hdmi-0 {
> +               hdmi-cec-pins {
> +                       pinmux = <GPIOMUX(14, GPOUT_SYS_HDMI_CEC_SDA,
> +                                             GPOEN_SYS_HDMI_CEC_SDA,
> +                                             GPI_SYS_HDMI_CEC_SDA)>;
> +                       input-enable;
> +                       bias-pull-up;
> +               };
> +
> +               hdmi-hpd-pins {
> +                       pinmux = <GPIOMUX(15, GPOUT_HIGH,
> +                                             GPOEN_ENABLE,
> +                                             GPI_SYS_HDMI_HPD)>;
> +                       input-enable;
> +                       bias-disable; /* external pull-up */
> +               };
> +
> +               hdmi-scl-pins {
> +                       pinmux = <GPIOMUX(0, GPOUT_SYS_HDMI_DDC_SCL,
> +                                            GPOEN_SYS_HDMI_DDC_SCL,
> +                                            GPI_SYS_HDMI_DDC_SCL)>;
> +                       input-enable;
> +                       bias-pull-up;
> +               };
> +
> +               hdmi-sda-pins {
> +                       pinmux = <GPIOMUX(1, GPOUT_SYS_HDMI_DDC_SDA,
> +                                            GPOEN_SYS_HDMI_DDC_SDA,
> +                                            GPI_SYS_HDMI_DDC_SDA)>;
> +                       input-enable;
> +                       bias-pull-up;
> +               };
> +       };
> +
>         i2c0_pins: i2c0-0 {
>                 i2c-pins {
>                         pinmux = <GPIOMUX(57, GPOUT_LOW,
> @@ -677,3 +788,7 @@ &U74_3 {
>  &U74_4 {
>         cpu-supply = <&vdd_cpu>;
>  };
> +
> +&voutcrg {
> +       status = "okay";
> +};
> diff --git a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> index
> 0ba74ef046792fd63ed6cf971fa1438609b06fb1..da670a44dcec0f3dae65a2612c2
> 4b79f3cdd7d6c 100644
> --- a/arch/riscv/boot/dts/starfive/jh7110.dtsi
> +++ b/arch/riscv/boot/dts/starfive/jh7110.dtsi
> @@ -283,12 +283,6 @@ gmac1_rmii_refin: gmac1-rmii-refin-clock {
>                 #clock-cells = <0>;
>         };
>  
> -       hdmitx0_pixelclk: hdmitx0-pixel-clock {
> -               compatible = "fixed-clock";
> -               clock-output-names = "hdmitx0_pixelclk";
> -               #clock-cells = <0>;
> -       };
> -
>         i2srx_bclk_ext: i2srx-bclk-ext-clock {
>                 compatible = "fixed-clock";
>                 clock-output-names = "i2srx_bclk_ext";
> @@ -344,6 +338,14 @@ tdm_ext: tdm-ext-clock {
>                 #clock-cells = <0>;
>         };
>  
> +       xin24m: xin24m {
> +               compatible = "fixed-clock";
> +               #clock-cells = <0>;
> +               clock-frequency = <24000000>;
> +               clock-output-names = "xin24m";
> +       };
> +
> +
>         soc {
>                 compatible = "simple-bus";
>                 interrupt-parent = <&plic>;
> @@ -1203,22 +1205,89 @@ camss: isp@19840000 {
>                         status = "disabled";
>                 };
>  
> -               voutcrg: clock-controller@295c0000 {
> -                       compatible = "starfive,jh7110-voutcrg";
> -                       reg = <0x0 0x295c0000 0x0 0x10000>;
> -                       clocks = <&syscrg JH7110_SYSCLK_VOUT_SRC>,
> -                                <&syscrg
> JH7110_SYSCLK_VOUT_TOP_AHB>,
> -                                <&syscrg
> JH7110_SYSCLK_VOUT_TOP_AXI>,
> -                                <&syscrg
> JH7110_SYSCLK_VOUT_TOP_HDMITX0_MCLK>,
> -                                <&syscrg JH7110_SYSCLK_I2STX0_BCLK>,
> -                                <&hdmitx0_pixelclk>;
> -                       clock-names = "vout_src", "vout_top_ahb",
> -                                     "vout_top_axi",
> "vout_top_hdmitx0_mclk",
> -                                     "i2stx0_bclk",
> "hdmitx0_pixelclk";
> -                       resets = <&syscrg
> JH7110_SYSRST_VOUT_TOP_SRC>;
> -                       #clock-cells = <1>;
> -                       #reset-cells = <1>;
> +               vout_subsystem: display-subsystem@29400000 {
> +                       compatible = "starfive,jh7110-vout-
> subsystem";
> +                       reg = <0x0 0x29400000 0x0 0x200000>;
> +                       #address-cells = <2>;
> +                       #size-cells = <2>;
> +                       ranges;
> +
>                         power-domains = <&pwrc JH7110_PD_VOUT>;
> +                       clocks = <&syscrg
> JH7110_SYSCLK_NOC_BUS_DISP_AXI>;
> +                       resets = <&syscrg
> JH7110_SYSRST_NOC_BUS_DISP_AXI>;
> +
> +                       dc8200: display@29400000 {
> +                               compatible = "verisilicon,dc";
> +                               reg = <0x0 0x29400000 0x0 0x2800>;
> +                               interrupts = <95>;
> +
> +                               clocks = <&voutcrg
> JH7110_VOUTCLK_DC8200_CORE>,
> +                                       <&voutcrg
> JH7110_VOUTCLK_DC8200_AXI>,
> +                                       <&voutcrg
> JH7110_VOUTCLK_DC8200_AHB>,
> +                                       <&voutcrg
> JH7110_VOUTCLK_DC8200_PIX0>,
> +                                       <&voutcrg
> JH7110_VOUTCLK_DC8200_PIX1>;
> +                               clock-names = "core", "axi", "ahb",
> "pix0", "pix1";
> +
> +                               resets = <&voutcrg
> JH7110_VOUTRST_DC8200_CORE>,
> +                                        <&voutcrg
> JH7110_VOUTRST_DC8200_AXI>,
> +                                        <&voutcrg
> JH7110_VOUTRST_DC8200_AHB>;
> +                               reset-names = "core", "axi", "ahb";
> +                       };
> +
> +                       hdmi_mfd: hdmi@29590000 {
> +                               compatible = "starfive,jh7110-hdmi-
> mfd";
> +                               reg = <0x0 0x29590000 0x0 0x4000>;
> +
> +                               hdmi_phy: phy {
> +                                       compatible =
> "starfive,jh7110-inno-hdmi-phy";
> +
> +                                       clocks = <&xin24m>;
> +                                       clock-names = "refoclk";
> +
> +                                       /* Output clock: The variable
> pixel clock */
> +                                       #clock-cells = <0>;
> +                                       clock-output-names =
> "hdmi_pclk";
> +
> +                                       /* PHY provider for the
> controller */
> +                                       #phy-cells = <0>;
> +                               };
> +
> +                               hdmi_controller: controller {
> +                                       compatible =
> "starfive,jh7110-inno-hdmi-controller";
> +                                       interrupts = <99>;
> +
> +                                       clocks = <&voutcrg
> JH7110_VOUTCLK_HDMI_TX_SYS>,
> +                                                <&voutcrg
> JH7110_VOUTCLK_HDMI_TX_MCLK>,
> +                                                <&voutcrg
> JH7110_VOUTCLK_HDMI_TX_BCLK>,
> +                                                <&hdmi_phy>;
> +                                       clock-names = "sys", "mclk",
> "bclk", "pclk";
> +
> +                                       resets = <&voutcrg
> JH7110_VOUTRST_HDMI_TX_HDMI>;
> +                                       reset-names = "hdmi_tx";
> +
> +                                       phys = <&hdmi_phy>;
> +                                       phy-names = "hdmi-phy";
> +                               };
> +                       };
> +
> +                       voutcrg: clock-controller@295c0000 {
> +                               compatible = "starfive,jh7110-
> voutcrg";
> +                               reg = <0x0 0x295c0000 0x0 0x10000>;
> +
> +                               clocks = <&syscrg
> JH7110_SYSCLK_VOUT_SRC>,
> +                                        <&syscrg
> JH7110_SYSCLK_VOUT_TOP_AHB>,
> +                                        <&syscrg
> JH7110_SYSCLK_VOUT_TOP_AXI>,
> +                                        <&syscrg
> JH7110_SYSCLK_VOUT_TOP_HDMITX0_MCLK>,
> +                                        <&syscrg
> JH7110_SYSCLK_I2STX0_BCLK>,
> +                                        <&hdmi_phy>;
> +                               clock-names = "vout_src",
> "vout_top_ahb",
> +                                             "vout_top_axi",
> "vout_top_hdmitx0_mclk",
> +                                             "i2stx0_bclk",
> "hdmitx0_pixelclk";
> +
> +                               resets = <&syscrg
> JH7110_SYSRST_VOUT_TOP_SRC>;
> +                               #clock-cells = <1>;
> +                               #reset-cells = <1>;
> +                       };
>                 };
>  
>                 pcie0: pcie@940000000 {
> 

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy