Re: [PATCH 11/15] arm64: dts: mediatek: mt7981b-openwrt-one: Enable SPI NOR

[AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>]

Il 16/10/25 12:08, Sjoerd Simons ha scritto:
> The openwrt one has a SPI NOR flash which from factory is used for:
> * Recovery system
> * WiFi eeprom data
> * ethernet Mac addresses
> 
> Describe this following the same partitions as the openwrt configuration
> uses.
> 
> Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
> ---
>   .../boot/dts/mediatek/mt7981b-openwrt-one.dts      | 83 ++++++++++++++++++++++
>   1 file changed, 83 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt7981b-openwrt-one.dts b/arch/arm64/boot/dts/mediatek/mt7981b-openwrt-one.dts
> index b6ca628ee72fd..9878009385cc6 100644
> --- a/arch/arm64/boot/dts/mediatek/mt7981b-openwrt-one.dts
> +++ b/arch/arm64/boot/dts/mediatek/mt7981b-openwrt-one.dts
> @@ -3,6 +3,7 @@
>   /dts-v1/;
>   
>   #include "mt7981b.dtsi"
> +#include "dt-bindings/pinctrl/mt65xx.h"
>   
>   / {
>   	compatible = "openwrt,one", "mediatek,mt7981b";
> @@ -54,6 +55,25 @@ mux {
>   		};
>   	};
>   
> +	spi2_flash_pins: spi2-pins {
> +		mux {
> +			function = "spi";
> +			groups = "spi2";
> +		};
> +
> +		conf-pu {
> +			bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
> +			drive-strength = <MTK_DRIVE_8mA>;

drive-strength = <8>;

> +			pins = "SPI2_CS", "SPI2_WP";
> +		};
> +
> +		conf-pd {
> +			bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
> +			drive-strength = <MTK_DRIVE_8mA>;

ditto

> +			pins = "SPI2_CLK", "SPI2_MOSI", "SPI2_MISO";
> +		};
> +	};
> +
>   	uart0_pins: uart0-pins {
>   		mux {
>   			function = "uart";
> @@ -62,6 +82,69 @@ mux {
>   	};
>   };
>   
> +&spi2 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&spi2_flash_pins>;
> +	status = "okay";
> +
> +	flash@0 {
> +		compatible = "jedec,spi-nor";
> +		reg = <0>;
> +		spi-max-frequency = <40000000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +
> +		partitions {
> +			compatible = "fixed-partitions";
> +			#address-cells = <1>;
> +			#size-cells = <1>;
> +
> +			partition@0 {
> +				reg = <0x00000 0x40000>;
> +				label = "bl2-nor";
> +			};
> +
> +			partition@40000 {
> +				reg = <0x40000 0xc0000>;
> +				label = "factory";
> +				read-only;
> +
> +				nvmem-layout {
> +					compatible = "fixed-layout";
> +					#address-cells = <1>;
> +					#size-cells = <1>;
> +
> +					eeprom_factory_0: eeprom@0 {

wifi_calibration:

> +						reg = <0x0 0x1000>;
> +					};
> +
> +					macaddr_factory_4: macaddr@4 {

macaddr_factory_gmac1?

You're not using this in the later commit where you enable ethernet nodes,
did you miss adding that to gmac1 or what is this used for?

> +						reg = <0x4 0x6>;
> +						compatible = "mac-base";
> +						#nvmem-cell-cells = <1>;
> +					};
> +
> +					macaddr_factory_24: macaddr@24 {

macaddr_factory_gmac0 ?


Cheers,
Angelo

-- 
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy