* Re: [PATCH net v4 1/2] net: phy: sfp: free mii_bus in sfp_i2c_mdiobus_destroy
From: Larysa Zaremba @ 2026-06-26 12:05 UTC (permalink / raw)
To: Petr Wozniak
Cc: Russell King, Andrew Lunn, Heiner Kallweit, Jakub Kicinski,
David S . Miller, Eric Dumazet, Paolo Abeni, netdev, linux-kernel,
linux-phy, Maxime Chevallier, Bjorn Mork, Aleksander Bajkowski,
Marek Behun
In-Reply-To: <20260624084814.20972-2-petr.wozniak@gmail.com>
On Wed, Jun 24, 2026 at 10:48:13AM +0200, Petr Wozniak wrote:
> sfp_i2c_mdiobus_create() allocates the I2C MDIO bus with mdio_i2c_alloc(),
> a plain (non-devm) allocation, and registers it. sfp_i2c_mdiobus_destroy()
> only unregisters the bus and clears sfp->i2c_mii without calling
> mdiobus_free(). As the only reference to the bus is then cleared, the
> struct mii_bus is leaked.
>
> This is hit whenever a copper/RollBall SFP module that instantiated an MDIO
> bus is removed: sfp_sm_main() takes the global teardown path and calls
> sfp_i2c_mdiobus_destroy(). sfp_cleanup(), on driver unbind, frees
> sfp->i2c_mii directly, which is why the leak only triggered on module
> hot-removal and not on unbind.
>
> Free the bus in sfp_i2c_mdiobus_destroy() to match the allocation done in
> sfp_i2c_mdiobus_create().
>
> Fixes: e85b1347ace6 ("net: sfp: create/destroy I2C mdiobus before PHY probe/after PHY release")
> Signed-off-by: Petr Wozniak <petr.wozniak@gmail.com>
> Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Larysa Zaremba <larysa.zaremba@intel.com>
> ---
> drivers/net/phy/sfp.c | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/drivers/net/phy/sfp.c b/drivers/net/phy/sfp.c
> index 03bfd8640db9..c4d274ab651e 100644
> --- a/drivers/net/phy/sfp.c
> +++ b/drivers/net/phy/sfp.c
> @@ -963,6 +963,7 @@ static int sfp_i2c_mdiobus_create(struct sfp *sfp)
> static void sfp_i2c_mdiobus_destroy(struct sfp *sfp)
> {
> mdiobus_unregister(sfp->i2c_mii);
> + mdiobus_free(sfp->i2c_mii);
> sfp->i2c_mii = NULL;
> }
>
> --
> 2.51.0
>
>
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply
* Re: [PATCH net v4 2/2] net: phy: mdio-i2c: defer RollBall bridge probe to PHY discovery
From: Maxime Chevallier @ 2026-06-26 15:10 UTC (permalink / raw)
To: Petr Wozniak, Russell King, Andrew Lunn, Heiner Kallweit
Cc: Jakub Kicinski, David S . Miller, Eric Dumazet, Paolo Abeni,
netdev, linux-kernel, linux-phy, Bjorn Mork, Aleksander Bajkowski,
Marek Behun
In-Reply-To: <20260624084814.20972-3-petr.wozniak@gmail.com>
Hi Petr,
On 6/24/26 10:48, Petr Wozniak wrote:
> commit 8fe125892f40 ("net: phy: sfp: probe for RollBall I2C-to-MDIO
> bridge in mdio-i2c") introduced a regression: the RollBall I2C-to-MDIO
> bridge is not yet ready to respond to CMD_READ/CMD_DONE cycles when
> sfp_sm_add_mdio_bus() runs in SFP_S_INIT. The 200 ms probe times out,
> i2c_mii_probe_rollball() returns -ENODEV, and sfp_sm_add_mdio_bus()
> sets mdio_protocol = MDIO_I2C_NONE. By the time sfp_sm_probe_for_phy()
> runs (up to ~17 s later on affected hardware), the bridge is fully
> initialized but PHY probing is skipped because the protocol has already
> been changed to NONE.
>
> This affects both modules inserted before boot and hotplugged modules on
> hardware where bridge initialization exceeds the 200 ms probe window
> (confirmed: FLYPRO SFP-10GT-CS-30M with Aquantia AQR113C, hotplugged).
>
> Move the probe from i2c_mii_init_rollball(), called at bus-creation time,
> to sfp_sm_probe_for_phy() in sfp.c, where it runs after the SFP state
> machine module initialization delays. Export the probe function as
> mdio_i2c_probe_rollball() so sfp.c can call it.
>
> For RTL8261BE-based modules the probe correctly returns -ENODEV at PHY
> discovery time, causing sfp_sm_probe_for_phy() to destroy the MDIO bus
> and set MDIO_I2C_NONE, eliminating the 5+ minute PHY probe retry loop.
>
> For genuine RollBall modules (e.g. FLYPRO SFP-10GT-CS-30M with Aquantia
> AQR113C) the probe now runs after initialization is complete and
> correctly returns 0, so PHY detection proceeds normally.
>
> Reported-by: Aleksander Bajkowski <olek2@wp.pl>
> Fixes: 8fe125892f40 ("net: phy: sfp: probe for RollBall I2C-to-MDIO bridge in mdio-i2c")
> Signed-off-by: Petr Wozniak <petr.wozniak@gmail.com>
I finally got time to test this with a RollBall module, and I
confirm what Aleksander says, the RollBall module's PHY doesn't
get detected even with this patch.
It does work on v7.0 though, so before the bridge probing was
introduced.
Maxime
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply
* Re: [PATCH net v4 2/2] net: phy: mdio-i2c: defer RollBall bridge probe to PHY discovery
From: Petr Wozniak @ 2026-06-26 16:35 UTC (permalink / raw)
To: maxime.chevallier, olek2, linux, andrew, hkallweit1
Cc: kuba, davem, edumazet, pabeni, netdev, linux-kernel, linux-phy,
bjorn, kabel, Petr Wozniak
In-Reply-To: <20260624084814.20972-3-petr.wozniak@gmail.com>
Maxime Chevallier wrote:
> I finally got time to test this with a RollBall module, and I
> confirm what Aleksander says, the RollBall module's PHY doesn't
> get detected even with this patch. It does work on v7.0 though,
> so before the bridge probing was introduced.
Thanks a lot for taking the time to test, Maxime - and Aleksander
for the original report.
That settles it: the deferred-probe approach in patch 2/2 doesn't
actually restore genuine RollBall PHY detection, and as you both
confirm it worked before 8fe125892f40 introduced the bridge probing.
Sashiko's static review flagged the same thing (the probe bypasses the
PHY discovery retry loop for slow-initializing modules), so the static
analysis and the two hardware reports all point at the same flaw.
I only have RTL8261BE-based copper modules here, not a genuine RollBall
one, so I can't develop and verify a proper slow-init timing fix
(module_t_wait / a retry that waits for the bridge) without the
hardware to test against.
Given that, my suggestion:
- Please drop patch 2/2 from the series.
- Since 8fe125892f40 regressed genuine RollBall detection and the
deferred probe doesn't restore it, I think the cleanest fix is to
revert 8fe125892f40. I'm happy to send that revert if you'd prefer.
The 5-minute RTL8261BE probe loop it was addressing is handled in our
downstream tree, so reverting it upstream is fine on our side.
- Patch 1/2 (the mii_bus leak fix) is independent of all this and
already has Reviewed-by from Maxime and Larysa - it would be good to
take that one regardless. I can resend it standalone if that's easier.
A proper fix covering slow-firmware modules really needs a genuine
RollBall module to validate, so it's better owned by someone who has
that hardware - happy to help review.
Thanks again,
Petr
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply
* [PATCH v8 02/29] phy: rockchip: usbdp: Update mode_change after error handling
From: Sebastian Reichel @ 2026-06-26 20:54 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, Sashiko
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
If rk_udphy_init() or rk_udphy_setup() fails, the reinit will not be
tried again. Fix this by only updating the variable after all potential
errors have been handled.
Note, that no errors have been seen on real hardware and failures would
most likely be fatal and require at least a full reboot as the function
already asserts the PHY reset lines. So this is more of a theoretical
issue.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612163835.8D5471F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index fba35510d88c..a5ffdf7a6e76 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1000,15 +1000,14 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
}
if (udphy->status == UDPHY_MODE_NONE) {
- udphy->mode_change = false;
ret = rk_udphy_setup(udphy);
if (ret)
return ret;
if (udphy->mode & UDPHY_MODE_USB)
rk_udphy_u3_port_disable(udphy, false);
- } else if (udphy->mode_change) {
udphy->mode_change = false;
+ } else if (udphy->mode_change) {
udphy->status = UDPHY_MODE_NONE;
if (udphy->mode == UDPHY_MODE_DP)
rk_udphy_u3_port_disable(udphy, true);
@@ -1017,6 +1016,7 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
ret = rk_udphy_setup(udphy);
if (ret)
return ret;
+ udphy->mode_change = false;
}
udphy->status |= mode;
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 04/29] phy: rockchip: usbdp: Fix devm_clk_bulk_get_all check
From: Sebastian Reichel @ 2026-06-26 20:54 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, Sashiko
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
If devm_clk_bulk_get_all() returns -EPROBE_DEFER, it is replaced with
-ENODEV, permanently failing the driver probe instead of allowing it to
defer. Avoid masking the error code to fix the issue.
This effectively drops returning -ENODEV in case no clocks are being
described in DT. This special case will now be handled by the follow-up
check searching for "refclk" and exit with -EINVAL.
None of this will be hit in practice, since the driver is only used by
RK3588 and RK3576 - on these platforms the DT is validated to contain
the clocks and the clock driver is force probed early. Thus there is
no need to backport this.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612164107.C7DB21F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 12dfdd470a78..2845a012eafc 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -427,8 +427,8 @@ static int rk_udphy_clk_init(struct rk_udphy *udphy, struct device *dev)
int i;
udphy->num_clks = devm_clk_bulk_get_all(dev, &udphy->clks);
- if (udphy->num_clks < 1)
- return -ENODEV;
+ if (udphy->num_clks < 0)
+ return udphy->num_clks;
/* used for configure phy reference clock frequency */
for (i = 0; i < udphy->num_clks; i++) {
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 03/29] phy: rockchip: usbdp: Do not lose USB3 PHY status
From: Sebastian Reichel @ 2026-06-26 20:54 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
By default (i.e. without manually enabling runtime PM) DWC3 requests the
USB3 PHY once and keeps it enabled all the time. When DisplayPort is
being requested later on, a mode change is needed. This re-initializes
the PHY. During re-initialization the status variable has incorrectly
been cleared, which means the tracking information for USB3 is lost.
This is not an immediate problem, since the DP side keeps the PHY
enabled. But once DP is toggled off, the whole PHY will be disabled.
This is a problem, because the USB side still needs it powered.
Fix things by not clearing the status flags.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 1 -
1 file changed, 1 deletion(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index a5ffdf7a6e76..12dfdd470a78 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1008,7 +1008,6 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
rk_udphy_u3_port_disable(udphy, false);
udphy->mode_change = false;
} else if (udphy->mode_change) {
- udphy->status = UDPHY_MODE_NONE;
if (udphy->mode == UDPHY_MODE_DP)
rk_udphy_u3_port_disable(udphy, true);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 00/29] phy: rockchip: usbdp: Fixes, DP 1-lane support and cleanups
From: Sebastian Reichel @ 2026-06-26 20:54 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, Sashiko, William Wu
This series overhauls the Rockchip USBDP driver; apart from a
a bunch of cleanups and small improvements the main goal is to
get the driver ready for proper USB-C DP AltMode support. At
the moment it only contains a semi-working state.
Once this series has landed, it unblocks enabling proper USB-C
DP AltMode on the RK3588 and RK3576 platforms incl. runtime PM
for the Synopsys DesignWare DisplayPort controller.
Apart from this series, further changes are required on the
DRM side. There are no compile-time dependencies between the
DRM side and the PHY side, but the PHY side must be applied
to avoid SErrors once runtime PM is added to the DisplayPort
controller driver. Thus it would be really good to land this
series ASAP as it blocks the DRM side.
Apart from that it also fixes a bunch of issues pointed out by
Sashiko (mostly harmless), as well as some real problems. Among
other things it should help drastically with orientation switch
problems and potential SErrors when a USB-C device is hot-plugged.
With this series applied, I did not notice any SErrors. What I do see is
cmn ana lcpll lock timeouts after a few replugs, which are permanent
(i.e. it still happens when re-trying to init the PHY after running into
the timeout). After a reboot the problem is gone. It seems the dynamic
USB3 disabling increased the chance a lot to hit this problem. I think
this is better than the current status where Serrors can appear on hotplug
due to the re-init. Unfortunately LCPLL is more or less undocumented in
the TRM, so it is hard to figure out what is going on exactly.
Changes in v8:
- Link to v7: https://lore.kernel.org/r/20260625-rockchip-usbdp-cleanup-v7-0-38eb3cf654fd@collabora.com
- Move patch "Limit DP lane count to muxed lanes" after single lane
support, which introduces dp_lanes variable to make sure series
is bi-sectable (Sashiko)
- Force disable HPD in "Drop seamless DP takeover" patch and update
patch description to mention potential issues with SErrors for
bootloaders really keeping the DW-DP on. As mentioned in the new
commit message this is untested as I'm not aware of such a
bootloader anyways; this also means we need to keep the HPD GRF
register defines in the 'Drop DP HPD handling' patch (Sashiko)
- Fix mode logic in "Properly handle TYPEC_STATE_SAFE and
TYPEC_STATE_USB" patch; I blame the heat (Sashiko)
- Improve "Support going from DP-only mode to USB mode" patch to
better handle starting in DP only mode; due to TypeC logic
starting delayed this does not really happen, though (Sashiko)
- Improve "Support going from DP-only mode to USB mode" to avoid
checking previous state and instead power on USB state based
on previous requested state to avoid effects from the flip
callback (Sashiko)
- Update the debug message patch to include some more info
- Ad one more patch, which disables USB3 at startup and drops
the -EPROBE_DEFER logic
Changes in v7:
- Link to v6: https://lore.kernel.org/r/20260619-rockchip-usbdp-cleanup-v6-0-3bb1f54b3f35@collabora.com
- Add new patch handling missing clock-names in DT gracefully (Sashiko)
- Add new patch handling rk_udphy_reset_deassert_all errors in init check (Sashiko)
- Add new patch to handle Properly handle TYPEC_STATE_SAFE and TYPEC_STATE_USB (Sashiko)
- Add new patch to avoid xHCI SErrors
Changes in v6:
- Link to v5: https://lore.kernel.org/r/20260612-rockchip-usbdp-cleanup-v5-0-efc83069869f@collabora.com
- Add explicit <linux/string_choices.h> include in last patch (Sashiko)
- Add new patch moving mode_change update after error handling (Sashiko)
- Add new patch fixing error masking of devm_clk_bulk_get_all() (Sashiko)
- Add new patch dropping seamless DP takeover as it is non-functional and buggy (Sashiko)
- Add new patch limiting DP lane count to muxed lanes (Sashiko)
- Add error handling in the patch that keeps clocks running on PHY re-init (Sashiko)
- Also look for DP being configured to second lane for the flip config
in DP single-lane mode, which should at least keep USB working for
this super unusual config (Sashiko)
- Drop useless ret variable in patch introducing guard() for the mutex
- Add error handling for PHY re-enablement in the patch fixing support for
DP-only -> USB mode (Sashiko)
Changes in v5:
- Link to v4: https://lore.kernel.org/r/20260428-rockchip-usbdp-cleanup-v4-0-7775671ece22@collabora.com
- Picked up Acked-by from Rob Herring for DT binding
- Fix typos in commit messages/comments
- Add Fixes tag to "Do not looe USB3 PHY status" patch
- Collect Reviewed-by: Neil Armstrong for multiple patches
- Drop now unused code from "Drop DP HPD handling" patch (Sashiko)
- Ignore mux events not involving DP AltMode (Sashiko)
- Add new patch to support going back from DP only mode to USB combo
mode; technically this is a fix, but DP mode does not yet work
upstream, so it does not matter (Sashiko)
- Add new patch adding a few debug messages, which are useful
to investigate potential hotplug issues in the future
- Sashiko comments about the DT binding and property usage
are wrong as the first port is for the superspeed lanes
used for DP and USB, while the last port is just about
DP aux. I ignored them.
- There is a pre-existing bug, that can already be hit with the
upstream kernel and that the series doesn't fix properly:
Accessing the USB3 controller registers requires the USB PHY
running, since it provides a clock. Re-initializing the PHY
means there is a race-condition - if the system tries to access
the USB3 controller in parallel to the re-init, the system will
hang and/or fail with an SError. By keeping the clocks running
and only asserting the resets this time is minimized by this
series. A proper fix for this will be looked into independently
from this series.
- I used v7.1-rc6 as base, but the driver has no changes since
6.18 even in linux-next and there are no pending patches for
it on the mailinglist either, so it applies to *any* recent
kernel branch.
Changes in v4:
- Link to v3: https://lore.kernel.org/r/20260313-rockchip-usbdp-cleanup-v3-0-3e8fe89a35b5@collabora.com
- rebased to v7.1-rc1 (no changes)
- Update DRM bridge registration patch to avoid registration when DP aux
port is not connected to anything, since this results in errors and some
boards use USBDP instances for USB3 only.
- Add patch renaming mode_change into phy_needs_reinit
- Add patch to re-init PHY on orientation change
- Add patch to factor out lane_mux_sel setup
- Add patch to handle mutex via guard functions
Changes in v3:
- Link to v2: https://lore.kernel.org/r/20260213-rockchip-usbdp-cleanup-v2-0-b67ec225f96e@collabora.com
- Add patch to register the USBDP PHY as DRM bridge
- Add patch to describe ports in DT binding (used by the DRM bridge)
- Add patch to drop HPD handling from the PHY
Changes in v2:
- Link to v1: https://lore.kernel.org/r/20260203-rockchip-usbdp-cleanup-v1-0-16a6f92ed176@collabora.com
- Added new patches to fix USB3 SError
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
Frank Wang (1):
phy: rockchip: usbdp: Amend SSC modulation deviation
Sebastian Reichel (26):
dt-bindings: phy: rockchip-usbdp: add improved ports scheme
phy: rockchip: usbdp: Update mode_change after error handling
phy: rockchip: usbdp: Do not lose USB3 PHY status
phy: rockchip: usbdp: Fix devm_clk_bulk_get_all check
phy: rockchip: usbdp: Handle missing clock-names DT property gracefully
phy: rockchip: usbdp: Drop seamless DP takeover
phy: rockchip: usbdp: Handle rk_udphy_reset_deassert_all errors in init check
phy: rockchip: usbdp: Keep clocks running on PHY re-init
phy: rockchip: usbdp: Add missing mode_change update
phy: rockchip: usbdp: Limit DP lane count to muxed lanes
phy: rockchip: usbdp: Rename DP lane functions
phy: rockchip: usbdp: Use FIELD_PREP_WM16_CONST
phy: rockchip: usbdp: Cleanup DP lane selection function
phy: rockchip: usbdp: Register DP aux bridge
phy: rockchip: usbdp: Drop DP HPD handling
phy: rockchip: usbdp: Rename mode_change to phy_needs_reinit
phy: rockchip: usbdp: Re-init the PHY on orientation change
phy: rockchip: usbdp: Factor out lane_mux_sel setup
phy: rockchip: usbdp: Properly handle TYPEC_STATE_SAFE and TYPEC_STATE_USB
phy: rockchip: usbdp: Use guard functions for mutex
phy: rockchip: usbdp: Support going from DP-only mode to USB mode
phy: rockchip: usbdp: Clear USB status on PHY exit
phy: rockchip: usbdp: Hold mutex in DP PHY configure
phy: rockchip: usbdp: Add some extra debug messages
phy: rockchip: usbdp: Avoid xHCI SErrors
phy: rockchip: usbdp: Disable USB3 on probe
William Wu (1):
phy: rockchip: usbdp: Fix LFPS detect threshold control
Zhang Yubing (1):
phy: rockchip: usbdp: Support single-lane DP
.../bindings/phy/phy-rockchip-usbdp.yaml | 23 ++
drivers/phy/rockchip/Kconfig | 2 +
drivers/phy/rockchip/phy-rockchip-usbdp.c | 427 ++++++++++-----------
3 files changed, 231 insertions(+), 221 deletions(-)
---
base-commit: 4edcdefd4083ae04b1a5656f4be6cd83ae919ef4
change-id: 20260203-rockchip-usbdp-cleanup-5b59dfb561a3
Best regards,
--
Sebastian Reichel <sebastian.reichel@collabora.com>
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply
* [PATCH v8 01/29] dt-bindings: phy: rockchip-usbdp: add improved ports scheme
From: Sebastian Reichel @ 2026-06-26 20:54 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
Currently the Rockchip USBDP PHY is missing a documented port scheme.
Meanwhile upstream RK3588 DTS files are a bit messy and use different
port schemes. The upstream USBDP PHY Linux kernel driver does not yet
parse the ports at all and thus does not create any implicit ABI either.
But with the current mess it is not possible to properly support USB-C
DP AltMode. Thus this introduces a proper port scheme following roughly
the ports design of the Qualcomm QMP USB4-USB3-DP PHY controller binding
with a slight difference that there is an additional port for the
USB-C SBU port as the Rockchip USB-DP PHY also contains the SBU mux.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
.../bindings/phy/phy-rockchip-usbdp.yaml | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-usbdp.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-usbdp.yaml
index 8b7059d5b182..f728acf057e4 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-usbdp.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-usbdp.yaml
@@ -114,6 +114,29 @@ properties:
A port node to link the PHY to a TypeC controller for the purpose of
handling orientation switching.
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description:
+ Output endpoint of the PHY for USB (or DP when configured into 4 lane
+ mode), which should point to the superspeed port of a USB connector.
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Incoming endpoint from the USB controller
+
+ port@2:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Incoming endpoint from the DisplayPort controller
+
+ port@3:
+ $ref: /schemas/graph.yaml#/properties/port
+ description:
+ Output endpoint of the PHY for DP, which should either point to the
+ SBU port of a USB-C connector or a DisplayPort connector input port.
+
required:
- compatible
- reg
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 08/29] phy: rockchip: usbdp: Keep clocks running on PHY re-init
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
When a mode change is required rk_udphy_power_on() disables
the clocks and then calls rk_udphy_setup(), which then enables
all the clocks again before continuing with rk_udphy_init().
Considering that rk_udphy_init() does assert the reset lines,
re-enabling the clocks is just delaying things. Avoid it by
directly calling rk_udphy_init().
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index b8de0a47a616..7fb7e4669f9d 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1020,8 +1020,7 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
if (udphy->mode == UDPHY_MODE_DP)
rk_udphy_u3_port_disable(udphy, true);
- rk_udphy_disable(udphy);
- ret = rk_udphy_setup(udphy);
+ ret = rk_udphy_init(udphy);
if (ret)
return ret;
udphy->mode_change = false;
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 06/29] phy: rockchip: usbdp: Drop seamless DP takeover
From: Sebastian Reichel @ 2026-06-26 20:54 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, Sashiko
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
Right now the DRM drivers do not support seamless DP takeover and I'm
I'm not aware of any bootloader implementing this feature either.
In any case this feature would be limited to boards using the USBDP PHY
for a DP or eDP connection instead of the more commonly USB-C connector.
With USB-C's DP AltMode a seamless DP takeover requires handing over the
state of the TCPM state machine from the bootloader to the kernel. This
in turn requires a huge amount of work to keep the state machine
implementations synchronized. It's very unlikely we will see somebody
implementing that in the foreseeable future.
As the current code is obviously buggy and untested, let's simply drop
support for seamless DP takeover. It can be re-implemented cleanly once
somebody adds all missing bits.
Technically the VOP side should be disabled first to avoid data being
send to an unpowered PHY from the running pipeline. As a workaround this
force disables HPD. I'm not sure if this would be good enough, but cannot
test as there is no support in the bootloaders known to me and my test
boards route USBDP to USB-C connectors.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612164107.C7DB21F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 11 +++++++----
1 file changed, 7 insertions(+), 4 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 3fc8222fcaec..f7ff55f03b7c 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -926,6 +926,7 @@ static int rk_udphy_parse_lane_mux_data(struct rk_udphy *udphy)
static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
{
+ const struct rk_udphy_cfg *cfg = udphy->cfgs;
int ret;
u32 value;
@@ -938,10 +939,12 @@ static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
rk_udphy_reset_deassert_all(udphy);
regmap_read(udphy->pma_regmap, CMN_LANE_MUX_AND_EN_OFFSET, &value);
- if (FIELD_GET(CMN_DP_LANE_MUX_ALL, value) && FIELD_GET(CMN_DP_LANE_EN_ALL, value))
- udphy->status = UDPHY_MODE_DP;
- else
- rk_udphy_disable(udphy);
+ if (FIELD_GET(CMN_DP_LANE_MUX_ALL, value) && FIELD_GET(CMN_DP_LANE_EN_ALL, value)) {
+ dev_info(udphy->dev, "Started with DP PHY pre-enabled; seamless takeover unsupported\n");
+ rk_udphy_grfreg_write(udphy->vogrf, &cfg->vogrfcfg[udphy->id].hpd_trigger, false);
+ }
+
+ rk_udphy_disable(udphy);
return 0;
}
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 12/29] phy: rockchip: usbdp: Support single-lane DP
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
From: Zhang Yubing <yubing.zhang@rock-chips.com>
Implement support for using just a single DisplayPort line.
Signed-off-by: Zhang Yubing <yubing.zhang@rock-chips.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 64 +++++++++++++------------------
1 file changed, 27 insertions(+), 37 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index d091f8007acd..5c38da0dadd2 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -193,6 +193,7 @@ struct rk_udphy {
int id;
bool dp_in_use;
+ int dp_lanes;
/* PHY const config */
const struct rk_udphy_cfg *cfgs;
@@ -540,6 +541,13 @@ static void rk_udphy_usb_bvalid_enable(struct rk_udphy *udphy, u8 enable)
* <0 1> dpln0 dpln1 usbrx usbtx
* <2 3> usbrx usbtx dpln0 dpln1
* ---------------------------------------------------------------------------
+ * if 1 lane for dp function, 2 lane for usb function, define rockchip,dp-lane-mux = <x>;
+ * sample as follow:
+ * ---------------------------------------------------------------------------
+ * B11-B10 A2-A3 A11-A10 B2-B3
+ * rockchip,dp-lane-mux ln0(tx/rx) ln1(tx) ln2(tx/rx) ln3(tx)
+ * <0> dpln0 \ usbrx usbtx
+ * ---------------------------------------------------------------------------
*/
static void rk_udphy_dplane_select(struct rk_udphy *udphy)
@@ -547,18 +555,18 @@ static void rk_udphy_dplane_select(struct rk_udphy *udphy)
const struct rk_udphy_cfg *cfg = udphy->cfgs;
u32 value = 0;
- switch (udphy->mode) {
- case UDPHY_MODE_DP:
- value |= 2 << udphy->dp_lane_sel[2] * 2;
+ switch (udphy->dp_lanes) {
+ case 4:
value |= 3 << udphy->dp_lane_sel[3] * 2;
+ value |= 2 << udphy->dp_lane_sel[2] * 2;
fallthrough;
- case UDPHY_MODE_DP_USB:
- value |= 0 << udphy->dp_lane_sel[0] * 2;
+ case 2:
value |= 1 << udphy->dp_lane_sel[1] * 2;
- break;
+ fallthrough;
- case UDPHY_MODE_USB:
+ case 1:
+ value |= 0 << udphy->dp_lane_sel[0] * 2;
break;
default:
@@ -571,28 +579,6 @@ static void rk_udphy_dplane_select(struct rk_udphy *udphy)
FIELD_PREP(DP_AUX_DOUT_SEL, udphy->dp_aux_dout_sel) | value);
}
-static int rk_udphy_dplane_get(struct rk_udphy *udphy)
-{
- int dp_lanes;
-
- switch (udphy->mode) {
- case UDPHY_MODE_DP:
- dp_lanes = 4;
- break;
-
- case UDPHY_MODE_DP_USB:
- dp_lanes = 2;
- break;
-
- case UDPHY_MODE_USB:
- default:
- dp_lanes = 0;
- break;
- }
-
- return dp_lanes;
-}
-
static void rk_udphy_dplane_enable(struct rk_udphy *udphy, int dp_lanes)
{
u32 val = 0;
@@ -662,6 +648,7 @@ static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
}
rk_udphy_mode_set(udphy, UDPHY_MODE_DP_USB);
+ udphy->dp_lanes = 2;
}
static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
@@ -900,7 +887,7 @@ static int rk_udphy_parse_lane_mux_data(struct rk_udphy *udphy)
return 0;
}
- if (num_lanes != 2 && num_lanes != 4)
+ if (num_lanes != 1 && num_lanes != 2 && num_lanes != 4)
return dev_err_probe(udphy->dev, -EINVAL,
"invalid number of lane mux\n");
@@ -926,9 +913,11 @@ static int rk_udphy_parse_lane_mux_data(struct rk_udphy *udphy)
}
udphy->mode = UDPHY_MODE_DP;
- if (num_lanes == 2) {
+ udphy->dp_lanes = num_lanes;
+ if (num_lanes == 1 || num_lanes == 2) {
udphy->mode |= UDPHY_MODE_USB;
- udphy->flip = (udphy->lane_mux_sel[0] == PHY_LANE_MUX_DP);
+ udphy->flip = (udphy->lane_mux_sel[0] == PHY_LANE_MUX_DP) ||
+ (udphy->lane_mux_sel[1] == PHY_LANE_MUX_DP);
}
return 0;
@@ -1083,18 +1072,17 @@ static int rk_udphy_dp_phy_exit(struct phy *phy)
static int rk_udphy_dp_phy_power_on(struct phy *phy)
{
struct rk_udphy *udphy = phy_get_drvdata(phy);
- int ret, dp_lanes;
+ int ret;
mutex_lock(&udphy->mutex);
- dp_lanes = rk_udphy_dplane_get(udphy);
- phy_set_bus_width(phy, dp_lanes);
+ phy_set_bus_width(phy, udphy->dp_lanes);
ret = rk_udphy_power_on(udphy, UDPHY_MODE_DP);
if (ret)
goto unlock;
- rk_udphy_dplane_enable(udphy, dp_lanes);
+ rk_udphy_dplane_enable(udphy, udphy->dp_lanes);
rk_udphy_dplane_select(udphy);
@@ -1374,6 +1362,7 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
udphy->lane_mux_sel[2] = PHY_LANE_MUX_DP;
udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
mode = UDPHY_MODE_DP;
+ udphy->dp_lanes = 4;
break;
case TYPEC_DP_STATE_D:
@@ -1390,6 +1379,7 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
}
mode = UDPHY_MODE_DP_USB;
+ udphy->dp_lanes = 2;
break;
}
@@ -1538,7 +1528,7 @@ static int rk_udphy_probe(struct platform_device *pdev)
ret = PTR_ERR(udphy->phy_dp);
return dev_err_probe(dev, ret, "failed to create DP phy\n");
}
- phy_set_bus_width(udphy->phy_dp, rk_udphy_dplane_get(udphy));
+ phy_set_bus_width(udphy->phy_dp, udphy->dp_lanes);
udphy->phy_dp->attrs.max_link_rate = 8100;
phy_set_drvdata(udphy->phy_dp, udphy);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 10/29] phy: rockchip: usbdp: Fix LFPS detect threshold control
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, William Wu
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
From: William Wu <william.wu@rock-chips.com>
According to the LFPS Tx Low Power/LFPS Rx Detect Threshold [1],
the device under test(DUT) must not respond if LFPS below the
minimum LFPS Rx Detect Threshold 100mV. Test fail on Rockchip
platforms, because the default LFPS detect threshold is set to
65mV.
The USBDP PHY LFPS detect threshold voltage could be set to
30mV ~ 140mV, and since there could be 10-20% PVT variation,
we set LFPS detect threshold voltage to 110mV.
[1] https://compliance.usb.org/resources/LFPS_Rx_Tx_Low_Power_Compliance_Update_Rev5.pdf
Signed-off-by: William Wu <william.wu@rock-chips.com>
[Taken over from rockchip's kernel tree; the registers are not described
in the TRM]
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 2aa9ccabf80b..c6d24dd3bdef 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -413,7 +413,8 @@ static const struct reg_sequence rk_udphy_init_sequence[] = {
{0x0070, 0x7d}, {0x0074, 0x68},
{0x0af4, 0x1a}, {0x1af4, 0x1a},
{0x0440, 0x3f}, {0x10d4, 0x08},
- {0x20d4, 0x08}, {0x0024, 0x6e}
+ {0x20d4, 0x08}, {0x0024, 0x6e},
+ {0x09c0, 0x0a}, {0x19c0, 0x0a}
};
static inline int rk_udphy_grfreg_write(struct regmap *base,
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 05/29] phy: rockchip: usbdp: Handle missing clock-names DT property gracefully
From: Sebastian Reichel @ 2026-06-26 20:54 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, Sashiko
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
The rk_udphy_clk_init() function would currently try to do a strncmp for
a NULL pointer, if DT specifies 'clocks' property, but no 'clock-names'
property. Fix this by making sure the clock has an id string set.
Note that DT binding requires setting clock-names, so this is only a
problem when booting a non-compliant device tree.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/message/20260619154349.071321F000E9%40smtp.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 2845a012eafc..3fc8222fcaec 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -432,6 +432,9 @@ static int rk_udphy_clk_init(struct rk_udphy *udphy, struct device *dev)
/* used for configure phy reference clock frequency */
for (i = 0; i < udphy->num_clks; i++) {
+ if (!udphy->clks[i].id)
+ continue;
+
if (!strncmp(udphy->clks[i].id, "refclk", 6)) {
udphy->refclk = udphy->clks[i].clk;
break;
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 09/29] phy: rockchip: usbdp: Amend SSC modulation deviation
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
From: Frank Wang <frank.wang@rock-chips.com>
Move SSC modulation deviation into private config of clock
- 24M: 0x00d4[5:0] = 0x30
- 26M: 0x00d4[5:0] = 0x33
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
[Taken over from rockchip's kernel tree; register 0x00d4 is not
described in the TRM]
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 7fb7e4669f9d..2aa9ccabf80b 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -350,7 +350,8 @@ static const struct reg_sequence rk_udphy_24m_refclk_cfg[] = {
{0x0a64, 0xa8}, {0x1a3c, 0xd0},
{0x1a44, 0xd0}, {0x1a48, 0x01},
{0x1a4c, 0x0d}, {0x1a54, 0xe0},
- {0x1a5c, 0xe0}, {0x1a64, 0xa8}
+ {0x1a5c, 0xe0}, {0x1a64, 0xa8},
+ {0x00d4, 0x30}
};
static const struct reg_sequence rk_udphy_26m_refclk_cfg[] = {
@@ -377,7 +378,7 @@ static const struct reg_sequence rk_udphy_26m_refclk_cfg[] = {
{0x0c30, 0x0e}, {0x0c48, 0x06},
{0x1c30, 0x0e}, {0x1c48, 0x06},
{0x028c, 0x18}, {0x0af0, 0x00},
- {0x1af0, 0x00}
+ {0x1af0, 0x00}, {0x00d4, 0x33}
};
static const struct reg_sequence rk_udphy_init_sequence[] = {
@@ -412,8 +413,7 @@ static const struct reg_sequence rk_udphy_init_sequence[] = {
{0x0070, 0x7d}, {0x0074, 0x68},
{0x0af4, 0x1a}, {0x1af4, 0x1a},
{0x0440, 0x3f}, {0x10d4, 0x08},
- {0x20d4, 0x08}, {0x00d4, 0x30},
- {0x0024, 0x6e},
+ {0x20d4, 0x08}, {0x0024, 0x6e}
};
static inline int rk_udphy_grfreg_write(struct regmap *base,
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 07/29] phy: rockchip: usbdp: Handle rk_udphy_reset_deassert_all errors in init check
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, Sashiko
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
Fix theoretical issue, that failure to deassert the reset lines would
result in an SError in follow-up register access. Note, that this cannot
happen with current code, since the Rockchip reset driver never returns
any errors for (de)asserting reset lines.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/message/20260619154903.2225A1F000E9%40smtp.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index f7ff55f03b7c..b8de0a47a616 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -936,7 +936,9 @@ static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
return ret;
}
- rk_udphy_reset_deassert_all(udphy);
+ ret = rk_udphy_reset_deassert_all(udphy);
+ if (ret)
+ goto exit;
regmap_read(udphy->pma_regmap, CMN_LANE_MUX_AND_EN_OFFSET, &value);
if (FIELD_GET(CMN_DP_LANE_MUX_ALL, value) && FIELD_GET(CMN_DP_LANE_EN_ALL, value)) {
@@ -944,9 +946,10 @@ static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
rk_udphy_grfreg_write(udphy->vogrf, &cfg->vogrfcfg[udphy->id].hpd_trigger, false);
}
+exit:
rk_udphy_disable(udphy);
- return 0;
+ return ret;
}
static int rk_udphy_parse_dt(struct rk_udphy *udphy)
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 11/29] phy: rockchip: usbdp: Add missing mode_change update
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
rk_udphy_set_typec_default_mapping() updates the available modes,
but does not set the mode_change as required. This results in
missing re-initialization and thus non-working DisplayPort.
Fix this issue by introducing a new helper to update the available
modes.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 16 +++++++++++-----
1 file changed, 11 insertions(+), 5 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index c6d24dd3bdef..d091f8007acd 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -622,6 +622,15 @@ static void rk_udphy_dp_hpd_event_trigger(struct rk_udphy *udphy, bool hpd)
rk_udphy_grfreg_write(udphy->vogrf, &cfg->vogrfcfg[udphy->id].hpd_trigger, hpd);
}
+static void rk_udphy_mode_set(struct rk_udphy *udphy, u8 mode)
+{
+ if (udphy->mode == mode)
+ return;
+
+ udphy->mode_change = true;
+ udphy->mode = mode;
+}
+
static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
{
if (udphy->flip) {
@@ -652,7 +661,7 @@ static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
gpiod_set_value_cansleep(udphy->sbu2_dc_gpio, 1);
}
- udphy->mode = UDPHY_MODE_DP_USB;
+ rk_udphy_mode_set(udphy, UDPHY_MODE_DP_USB);
}
static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
@@ -1394,10 +1403,7 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
usleep_range(750, 800);
rk_udphy_dp_hpd_event_trigger(udphy, true);
} else if (data->status & DP_STATUS_HPD_STATE) {
- if (udphy->mode != mode) {
- udphy->mode = mode;
- udphy->mode_change = true;
- }
+ rk_udphy_mode_set(udphy, mode);
rk_udphy_dp_hpd_event_trigger(udphy, true);
} else {
rk_udphy_dp_hpd_event_trigger(udphy, false);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 13/29] phy: rockchip: usbdp: Limit DP lane count to muxed lanes
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, Sashiko
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
In theory the DP controller could request 4 lanes when the PHY is
restricted to 2 lanes as the other half is used by USB3.
With the current user (DW-DP) this cannot happen, but as the check is
cheap and users might change in the future protect things accordingly.
Not doing so would corrupt USB3 usage by the following code configuring
the voltages.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612165546.98E1F1F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 5c38da0dadd2..6de8ac3f9144 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1132,6 +1132,9 @@ static int rk_udphy_dp_phy_verify_link_rate(struct rk_udphy *udphy,
static int rk_udphy_dp_phy_verify_lanes(struct rk_udphy *udphy,
struct phy_configure_opts_dp *dp)
{
+ if (dp->lanes > udphy->dp_lanes)
+ return -EINVAL;
+
switch (dp->lanes) {
case 1:
case 2:
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 14/29] phy: rockchip: usbdp: Rename DP lane functions
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
The common prefix for DisplayPort related functions is rk_udphy_dp_
(with a final _), so update the two DP lane functions to follow that
scheme.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 6de8ac3f9144..db1ad3c2a953 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -550,7 +550,7 @@ static void rk_udphy_usb_bvalid_enable(struct rk_udphy *udphy, u8 enable)
* ---------------------------------------------------------------------------
*/
-static void rk_udphy_dplane_select(struct rk_udphy *udphy)
+static void rk_udphy_dp_lane_select(struct rk_udphy *udphy)
{
const struct rk_udphy_cfg *cfg = udphy->cfgs;
u32 value = 0;
@@ -579,7 +579,7 @@ static void rk_udphy_dplane_select(struct rk_udphy *udphy)
FIELD_PREP(DP_AUX_DOUT_SEL, udphy->dp_aux_dout_sel) | value);
}
-static void rk_udphy_dplane_enable(struct rk_udphy *udphy, int dp_lanes)
+static void rk_udphy_dp_lane_enable(struct rk_udphy *udphy, int dp_lanes)
{
u32 val = 0;
int i;
@@ -1082,9 +1082,9 @@ static int rk_udphy_dp_phy_power_on(struct phy *phy)
if (ret)
goto unlock;
- rk_udphy_dplane_enable(udphy, udphy->dp_lanes);
+ rk_udphy_dp_lane_enable(udphy, udphy->dp_lanes);
- rk_udphy_dplane_select(udphy);
+ rk_udphy_dp_lane_select(udphy);
unlock:
mutex_unlock(&udphy->mutex);
@@ -1102,7 +1102,7 @@ static int rk_udphy_dp_phy_power_off(struct phy *phy)
struct rk_udphy *udphy = phy_get_drvdata(phy);
mutex_lock(&udphy->mutex);
- rk_udphy_dplane_enable(udphy, 0);
+ rk_udphy_dp_lane_enable(udphy, 0);
rk_udphy_power_off(udphy, UDPHY_MODE_DP);
mutex_unlock(&udphy->mutex);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 15/29] phy: rockchip: usbdp: Use FIELD_PREP_WM16_CONST
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
Cleanup code by replacing open-coded version of FIELD_PREP_WM16_CONST
with the existing helper macro.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index db1ad3c2a953..d8978cd22707 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -12,6 +12,7 @@
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/gpio.h>
+#include <linux/hw_bitfield.h>
#include <linux/mfd/syscon.h>
#include <linux/mod_devicetable.h>
#include <linux/module.h>
@@ -75,7 +76,6 @@
#define TRSV_LN2_MON_RX_CDR_DONE_OFFSET 0x1b84 /* trsv_reg06E1 */
#define TRSV_LN2_MON_RX_CDR_LOCK_DONE BIT(0)
-#define BIT_WRITEABLE_SHIFT 16
#define PHY_AUX_DP_DATA_POL_NORMAL 0
#define PHY_AUX_DP_DATA_POL_INVERT 1
#define PHY_LANE_MUX_USB 0
@@ -104,8 +104,8 @@ struct rk_udphy_grf_reg {
#define _RK_UDPHY_GEN_GRF_REG(offset, mask, disable, enable) \
{\
offset, \
- FIELD_PREP_CONST(mask, disable) | (mask << BIT_WRITEABLE_SHIFT), \
- FIELD_PREP_CONST(mask, enable) | (mask << BIT_WRITEABLE_SHIFT), \
+ FIELD_PREP_WM16_CONST(mask, disable), \
+ FIELD_PREP_WM16_CONST(mask, enable), \
}
#define RK_UDPHY_GEN_GRF_REG(offset, bitend, bitstart, disable, enable) \
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 20/29] phy: rockchip: usbdp: Re-init the PHY on orientation change
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
Changing the cable orientation reconfigures the lane muxing, which
requires re-initializing the PHY. Without this DP functionality
breaks, if the cable is re-plugged with swapped orientation.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 1bb22fc18c9f..3d222768dc3c 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -626,6 +626,7 @@ static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
enum typec_orientation orien)
{
struct rk_udphy *udphy = typec_switch_get_drvdata(sw);
+ bool flipped = orien == TYPEC_ORIENTATION_REVERSE;
mutex_lock(&udphy->mutex);
@@ -637,7 +638,10 @@ static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
goto unlock_ret;
}
- udphy->flip = orien == TYPEC_ORIENTATION_REVERSE;
+ if (udphy->flip != flipped)
+ udphy->phy_needs_reinit = true;
+
+ udphy->flip = flipped;
rk_udphy_set_typec_default_mapping(udphy);
rk_udphy_usb_bvalid_enable(udphy, true);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 23/29] phy: rockchip: usbdp: Use guard functions for mutex
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
Convert the driver to use guard functions for mutex handling as
a small cleanup. There is a small functional change in the DP PHY
power up function, which no longer sleeps if the internal powerup
code returns an error. This is not a problem as the sleep is only
relevant for successful power-up.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 54 +++++++++++++------------------
1 file changed, 23 insertions(+), 31 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 63fb41ad0199..837a4cb3e4b6 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -10,6 +10,7 @@
#include <dt-bindings/phy/phy.h>
#include <linux/bitfield.h>
#include <linux/bits.h>
+#include <linux/cleanup.h>
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/gpio.h>
@@ -656,14 +657,15 @@ static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
struct rk_udphy *udphy = typec_switch_get_drvdata(sw);
bool flipped = orien == TYPEC_ORIENTATION_REVERSE;
- mutex_lock(&udphy->mutex);
+ guard(mutex)(&udphy->mutex);
if (orien == TYPEC_ORIENTATION_NONE) {
gpiod_set_value_cansleep(udphy->sbu1_dc_gpio, 0);
gpiod_set_value_cansleep(udphy->sbu2_dc_gpio, 0);
/* unattached */
rk_udphy_usb_bvalid_enable(udphy, false);
- goto unlock_ret;
+
+ return 0;
}
if (udphy->flip != flipped)
@@ -673,8 +675,6 @@ static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
rk_udphy_set_typec_default_mapping(udphy);
rk_udphy_usb_bvalid_enable(udphy, true);
-unlock_ret:
- mutex_unlock(&udphy->mutex);
return 0;
}
@@ -1054,26 +1054,25 @@ static int rk_udphy_dp_phy_power_on(struct phy *phy)
struct rk_udphy *udphy = phy_get_drvdata(phy);
int ret;
- mutex_lock(&udphy->mutex);
+ scoped_guard(mutex, &udphy->mutex) {
+ phy_set_bus_width(phy, udphy->dp_lanes);
- phy_set_bus_width(phy, udphy->dp_lanes);
-
- ret = rk_udphy_power_on(udphy, UDPHY_MODE_DP);
- if (ret)
- goto unlock;
+ ret = rk_udphy_power_on(udphy, UDPHY_MODE_DP);
+ if (ret)
+ return ret;
- rk_udphy_dp_lane_enable(udphy, udphy->dp_lanes);
+ rk_udphy_dp_lane_enable(udphy, udphy->dp_lanes);
- rk_udphy_dp_lane_select(udphy);
+ rk_udphy_dp_lane_select(udphy);
+ }
-unlock:
- mutex_unlock(&udphy->mutex);
/*
* If data send by aux channel too fast after phy power on,
* the aux may be not ready which will cause aux error. Adding
* delay to avoid this issue.
*/
usleep_range(10000, 11000);
+
return ret;
}
@@ -1081,10 +1080,10 @@ static int rk_udphy_dp_phy_power_off(struct phy *phy)
{
struct rk_udphy *udphy = phy_get_drvdata(phy);
- mutex_lock(&udphy->mutex);
+ guard(mutex)(&udphy->mutex);
+
rk_udphy_dp_lane_enable(udphy, 0);
rk_udphy_power_off(udphy, UDPHY_MODE_DP);
- mutex_unlock(&udphy->mutex);
return 0;
}
@@ -1289,35 +1288,30 @@ static const struct phy_ops rk_udphy_dp_phy_ops = {
static int rk_udphy_usb3_phy_init(struct phy *phy)
{
struct rk_udphy *udphy = phy_get_drvdata(phy);
- int ret = 0;
- mutex_lock(&udphy->mutex);
+ guard(mutex)(&udphy->mutex);
+
/* DP only or high-speed, disable U3 port */
if (!(udphy->mode & UDPHY_MODE_USB) || udphy->hs) {
rk_udphy_u3_port_disable(udphy, true);
- goto unlock;
+ return 0;
}
- ret = rk_udphy_power_on(udphy, UDPHY_MODE_USB);
-
-unlock:
- mutex_unlock(&udphy->mutex);
- return ret;
+ return rk_udphy_power_on(udphy, UDPHY_MODE_USB);
}
static int rk_udphy_usb3_phy_exit(struct phy *phy)
{
struct rk_udphy *udphy = phy_get_drvdata(phy);
- mutex_lock(&udphy->mutex);
+ guard(mutex)(&udphy->mutex);
+
/* DP only or high-speed */
if (!(udphy->mode & UDPHY_MODE_USB) || udphy->hs)
- goto unlock;
+ return 0;
rk_udphy_power_off(udphy, UDPHY_MODE_USB);
-unlock:
- mutex_unlock(&udphy->mutex);
return 0;
}
@@ -1349,12 +1343,10 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
if (!rk_udphy_is_supported_mode(state))
return 0;
- mutex_lock(&udphy->mutex);
+ guard(mutex)(&udphy->mutex);
rk_udphy_set_typec_state(udphy, state->mode);
- mutex_unlock(&udphy->mutex);
-
return 0;
}
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 21/29] phy: rockchip: usbdp: Factor out lane_mux_sel setup
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
Avoid describing the USB+DP lane_mux_sel logic twice by introducing
a helper function to reduce code duplication.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 81 +++++++++++++++----------------
1 file changed, 40 insertions(+), 41 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 3d222768dc3c..7c3b0d45d938 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -588,6 +588,42 @@ static void rk_udphy_mode_set(struct rk_udphy *udphy, u8 mode)
udphy->mode = mode;
}
+static void rk_udphy_set_typec_state(struct rk_udphy *udphy, unsigned long state)
+{
+ u8 mode;
+
+ switch (state) {
+ case TYPEC_DP_STATE_C:
+ case TYPEC_DP_STATE_E:
+ udphy->lane_mux_sel[0] = PHY_LANE_MUX_DP;
+ udphy->lane_mux_sel[1] = PHY_LANE_MUX_DP;
+ udphy->lane_mux_sel[2] = PHY_LANE_MUX_DP;
+ udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
+ mode = UDPHY_MODE_DP;
+ udphy->dp_lanes = 4;
+ break;
+
+ case TYPEC_DP_STATE_D:
+ default:
+ if (udphy->flip) {
+ udphy->lane_mux_sel[0] = PHY_LANE_MUX_DP;
+ udphy->lane_mux_sel[1] = PHY_LANE_MUX_DP;
+ udphy->lane_mux_sel[2] = PHY_LANE_MUX_USB;
+ udphy->lane_mux_sel[3] = PHY_LANE_MUX_USB;
+ } else {
+ udphy->lane_mux_sel[0] = PHY_LANE_MUX_USB;
+ udphy->lane_mux_sel[1] = PHY_LANE_MUX_USB;
+ udphy->lane_mux_sel[2] = PHY_LANE_MUX_DP;
+ udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
+ }
+ mode = UDPHY_MODE_DP_USB;
+ udphy->dp_lanes = 2;
+ break;
+ }
+
+ rk_udphy_mode_set(udphy, mode);
+}
+
static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
{
if (udphy->flip) {
@@ -595,10 +631,6 @@ static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
udphy->dp_lane_sel[1] = 1;
udphy->dp_lane_sel[2] = 3;
udphy->dp_lane_sel[3] = 2;
- udphy->lane_mux_sel[0] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[1] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[2] = PHY_LANE_MUX_USB;
- udphy->lane_mux_sel[3] = PHY_LANE_MUX_USB;
udphy->dp_aux_dout_sel = PHY_AUX_DP_DATA_POL_INVERT;
udphy->dp_aux_din_sel = PHY_AUX_DP_DATA_POL_INVERT;
gpiod_set_value_cansleep(udphy->sbu1_dc_gpio, 1);
@@ -608,18 +640,14 @@ static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
udphy->dp_lane_sel[1] = 3;
udphy->dp_lane_sel[2] = 1;
udphy->dp_lane_sel[3] = 0;
- udphy->lane_mux_sel[0] = PHY_LANE_MUX_USB;
- udphy->lane_mux_sel[1] = PHY_LANE_MUX_USB;
- udphy->lane_mux_sel[2] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
udphy->dp_aux_dout_sel = PHY_AUX_DP_DATA_POL_NORMAL;
udphy->dp_aux_din_sel = PHY_AUX_DP_DATA_POL_NORMAL;
gpiod_set_value_cansleep(udphy->sbu1_dc_gpio, 0);
gpiod_set_value_cansleep(udphy->sbu2_dc_gpio, 1);
}
- rk_udphy_mode_set(udphy, UDPHY_MODE_DP_USB);
- udphy->dp_lanes = 2;
+ /* default to USB3 + DP as 4 lane USB is not supported */
+ rk_udphy_set_typec_state(udphy, TYPEC_DP_STATE_D);
}
static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
@@ -1303,7 +1331,6 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
struct typec_mux_state *state)
{
struct rk_udphy *udphy = typec_mux_get_drvdata(mux);
- u8 mode;
/*
* Ignore mux events not involving DP AltMode, because
@@ -1315,38 +1342,10 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
mutex_lock(&udphy->mutex);
- switch (state->mode) {
- case TYPEC_DP_STATE_C:
- case TYPEC_DP_STATE_E:
- udphy->lane_mux_sel[0] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[1] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[2] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
- mode = UDPHY_MODE_DP;
- udphy->dp_lanes = 4;
- break;
-
- case TYPEC_DP_STATE_D:
- default:
- if (udphy->flip) {
- udphy->lane_mux_sel[0] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[1] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[2] = PHY_LANE_MUX_USB;
- udphy->lane_mux_sel[3] = PHY_LANE_MUX_USB;
- } else {
- udphy->lane_mux_sel[0] = PHY_LANE_MUX_USB;
- udphy->lane_mux_sel[1] = PHY_LANE_MUX_USB;
- udphy->lane_mux_sel[2] = PHY_LANE_MUX_DP;
- udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
- }
- mode = UDPHY_MODE_DP_USB;
- udphy->dp_lanes = 2;
- break;
- }
-
- rk_udphy_mode_set(udphy, mode);
+ rk_udphy_set_typec_state(udphy, state->mode);
mutex_unlock(&udphy->mutex);
+
return 0;
}
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 26/29] phy: rockchip: usbdp: Hold mutex in DP PHY configure
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel, Sashiko
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
rk_udphy_dp_phy_configure() accesses some variables from the struct
rk_udphy, which are updated independently from the USB-C framework.
The USB-C mux/orientation switch functions already hold a mutex to
ensure mutual exclusive access to the struct rk_udphy states, so
simply hold the same one in the DP PHY configuration function.
Reproducing problems due to this on real hardware would be really hard,
but could be possible when quickly re-connecting the USB-C connector.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612164627.23D391F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 15c18c6e3093..2681610d10d5 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1193,6 +1193,8 @@ static int rk_udphy_dp_phy_configure(struct phy *phy,
u32 i, val, lane;
int ret;
+ guard(mutex)(&udphy->mutex);
+
if (dp->set_rate) {
ret = rk_udphy_dp_phy_verify_link_rate(udphy, dp);
if (ret)
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 29/29] phy: rockchip: usbdp: Disable USB3 on probe
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
Disable USB3 support during probe, so that the driver always starts with
a clean state. With this it no longer makes sense to use -EPROBE_DEFER
for cmn ana lcpll lock timeouts afterwards. This error code should only
appear during probe and the PHY initialization function is also being
called at normal runtime.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 14 +++-----------
1 file changed, 3 insertions(+), 11 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 7c8b9eaaf352..a25cce0b7337 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -755,17 +755,7 @@ static int rk_udphy_status_check(struct rk_udphy *udphy)
(val & CMN_ANA_LCPLL_LOCK_DONE), 200, 100000);
if (ret) {
dev_err(udphy->dev, "cmn ana lcpll lock timeout\n");
- /*
- * If earlier software (U-Boot) enabled USB once already
- * the PLL may have problems locking on the first try.
- * It will be successful on the second try, so for the
- * time being a -EPROBE_DEFER will solve the issue.
- *
- * This requires further investigation to understand the
- * root cause, especially considering that the driver is
- * asserting all reset lines at probe time.
- */
- return -EPROBE_DEFER;
+ return ret;
}
if (!udphy->flip) {
@@ -962,6 +952,8 @@ static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
rk_udphy_grfreg_write(udphy->vogrf, &cfg->vogrfcfg[udphy->id].hpd_trigger, false);
}
+ rk_udphy_u3_port_disable(udphy, true);
+
exit:
rk_udphy_disable(udphy);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v8 27/29] phy: rockchip: usbdp: Add some extra debug messages
From: Sebastian Reichel @ 2026-06-26 20:55 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, Sebastian Reichel
In-Reply-To: <20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com>
It's useful to log PHY reinit to ease debugging issues around
USB-C hotplugging.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 17 ++++++++++++++++-
1 file changed, 16 insertions(+), 1 deletion(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 2681610d10d5..dc166392ba19 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -24,6 +24,7 @@
#include <linux/property.h>
#include <linux/regmap.h>
#include <linux/reset.h>
+#include <linux/string_choices.h>
#include <linux/usb/ch9.h>
#include <linux/usb/typec_dp.h>
#include <linux/usb/typec_mux.h>
@@ -469,6 +470,8 @@ static int rk_udphy_reset_deassert(struct rk_udphy *udphy, char *name)
return reset_control_deassert(list[idx].rstc);
}
+ dev_err(udphy->dev, "failed to de-assert missing reset line: %s\n", name);
+
return -EINVAL;
}
@@ -495,6 +498,8 @@ static void rk_udphy_u3_port_disable(struct rk_udphy *udphy, u8 disable)
const struct rk_udphy_cfg *cfg = udphy->cfgs;
const struct rk_udphy_grf_reg *preg;
+ dev_dbg(udphy->dev, "USB3 port %s\n", str_on_off(!disable));
+
preg = udphy->id ? &cfg->grfcfg.usb3otg1_cfg : &cfg->grfcfg.usb3otg0_cfg;
rk_udphy_grfreg_write(udphy->usbgrf, preg, disable);
}
@@ -788,6 +793,11 @@ static int rk_udphy_init(struct rk_udphy *udphy)
const struct rk_udphy_cfg *cfg = udphy->cfgs;
int ret;
+ dev_dbg(udphy->dev, "(re-)init PHY with USB=%s and DP=%s (%u lanes) flipped=%s\n",
+ str_enabled_disabled(udphy->mode & UDPHY_MODE_USB),
+ str_enabled_disabled(udphy->mode & UDPHY_MODE_DP),
+ udphy->dp_lanes, str_yes_no(udphy->flip));
+
rk_udphy_reset_assert_all(udphy);
usleep_range(10000, 11000);
@@ -858,6 +868,8 @@ static int rk_udphy_setup(struct rk_udphy *udphy)
{
int ret;
+ dev_dbg(udphy->dev, "enable PHY\n");
+
ret = clk_bulk_prepare_enable(udphy->num_clks, udphy->clks);
if (ret) {
dev_err(udphy->dev, "failed to enable clk\n");
@@ -876,6 +888,7 @@ static int rk_udphy_setup(struct rk_udphy *udphy)
static void rk_udphy_disable(struct rk_udphy *udphy)
{
+ dev_dbg(udphy->dev, "disable PHY\n");
clk_bulk_disable_unprepare(udphy->num_clks, udphy->clks);
rk_udphy_reset_assert_all(udphy);
}
@@ -1359,8 +1372,10 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
struct rk_udphy *udphy = typec_mux_get_drvdata(mux);
/* Ignore mux events not involving USB or DP */
- if (!rk_udphy_is_supported_mode(state))
+ if (!rk_udphy_is_supported_mode(state)) {
+ dev_dbg(udphy->dev, "ignore mux event with mode=%lu\n", state->mode);
return 0;
+ }
guard(mutex)(&udphy->mutex);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox