* Re: [PATCH v8 1/2] dt-bindings: phy: qcom: Add CSI2 C-PHY/DPHY schema
From: Bryan O'Donoghue @ 2026-07-01 22:54 UTC (permalink / raw)
To: Vladimir Zapolskiy, Bryan O'Donoghue, Vinod Koul,
Kishon Vijay Abraham I, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Neil Armstrong
Cc: linux-arm-msm, linux-phy, linux-media, devicetree, linux-kernel
In-Reply-To: <dda32577-04e0-4507-acaf-a5694f4f31b3@linaro.org>
On 02/06/2026 22:59, Vladimir Zapolskiy wrote:
>> +
>> + "#phy-cells":
>> + const: 1
>> + description:
>> + The single cell specifies the PHY operating mode.
> #phy-cells should be 0, because the PHY operating mode is well defined
> by 'bus-type' property of an endpoint on the sensor side, the opposite
> side of CAMSS/CSID as a CSIPHY "consumer" should not dictate the PHY type.
So going through the list I don't believe this is correct.
Inserting bus-type into the PHY layer is borrowing from one domain
linux-media and pushing the concept into PHYs.
phy-cells = 1 with CPHY/DPHY specified in the consumer, as was Rob's
suggestion will specify the mode.
Then to understand if we are in regular or combo mode, we parse the
ports/endspoints in the PHY node as we've agreed already.
---
bod
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply
* Re: [PATCH v4 4/4] phy: qcom: qmp-usbc: Add qmp configuration for Shikra
From: Dmitry Baryshkov @ 2026-07-01 23:24 UTC (permalink / raw)
To: Krishna Kurapati
Cc: Neil Armstrong, Vinod Koul, Rob Herring, Krzysztof Kozlowski,
Conor Dooley, Bjorn Andersson, Konrad Dybcio, Xiangxu Yin,
Johan Hovold, Loic Poulain, Shawn Guo, Abel Vesa, Wesley Cheng,
linux-arm-msm, linux-phy, devicetree, linux-kernel
In-Reply-To: <20260701165051.4122259-5-krishna.kurapati@oss.qualcomm.com>
On Wed, Jul 01, 2026 at 10:20:51PM +0530, Krishna Kurapati wrote:
> Add init sequence and phy configuration for the Super Speed port on Shikra
> SoC. Also since Shikra uses 3 resets, add support for the third reset and
> configure Shikra platform data to use 3 resets.
>
> Signed-off-by: Krishna Kurapati <krishna.kurapati@oss.qualcomm.com>
> ---
> drivers/phy/qualcomm/phy-qcom-qmp-usbc.c | 53 ++++++++++++++++++++++--
> 1 file changed, 50 insertions(+), 3 deletions(-)
>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
--
With best wishes
Dmitry
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply
* [PATCH v9 04/38] phy: rockchip: usbdp: Fix devm_clk_bulk_get_all check
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
If devm_clk_bulk_get_all() returns -EPROBE_DEFER, it is replaced with
-ENODEV, permanently failing the driver probe instead of allowing it to
defer. Avoid masking the error code to fix the issue.
This effectively drops returning -ENODEV in case no clocks are being
described in DT. This special case will now be handled by the follow-up
check searching for "refclk" and exit with -EINVAL.
None of this will be hit in practice, since the driver is only used by
RK3588 and RK3576 - on these platforms the DT is validated to contain
the clocks and the clock driver is force probed early. Thus there is
no need to backport this.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612164107.C7DB21F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 12dfdd470a78..2845a012eafc 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -427,8 +427,8 @@ static int rk_udphy_clk_init(struct rk_udphy *udphy, struct device *dev)
int i;
udphy->num_clks = devm_clk_bulk_get_all(dev, &udphy->clks);
- if (udphy->num_clks < 1)
- return -ENODEV;
+ if (udphy->num_clks < 0)
+ return udphy->num_clks;
/* used for configure phy reference clock frequency */
for (i = 0; i < udphy->num_clks; i++) {
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 00/38] phy: rockchip: usbdp: Clean up the mess
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko, William Wu
This series does a major overhaul of the Rockchip USBDP driver. The
initial main goal was to add USB-C DP AltMode support to the RK3576
and RK3588 and this series still prepares the PHY driver for exactly
that. But in addition to that I uncovered a huge amount of issues,
that are fixed along the way. Some of the more interesting ones are:
* Currently the driver might trigger a fatal SError on USB-C hotplug,
since re-initializing the PHY stops the clocks going to DWC3. If
the DWC3 driver tries to access its registers at the same time the
system will crash.
* The DWC3 hardware can get into a buggy state when the PHY is
disabled, which results in the PHY not coming up properly again.
* Swithcing the USB-C connector orientation during hotplug breaks
USB3 speed, as the PHY is not being re-initialized.
* Once DP is support the PHY initializes DP mode, even when the DRM
side did not request DP support.
* The driver has some locking issues uncovered by Sashiko.
In addition to these bigger ones, Sashiko also found a bunch of
minor problems, which are mostly harmless, but were fixed while
going at it.
I've tested the v9 code changes with dozens of replugs of different
devices (2 different USB-C hubs with USB3 + HDMI via DP AltMode,
1 USB-C to HDMI adapter [4 lanes DP AltMode], 1 USB-C to DP adapter
[4 lanes DP AltMode], 1 USB-C to NVMe adapter [no DP AltMode] as
well as a direct USB-C connection to a Dell display) on a Sige 5
board and haven't run into any issues. In all cases USB3 was working
in both directions and DP mode was properly initialized, so that
the DRM driver could query the available modes.
Technically some of the later patches are fixes, that one would
expect at the beginning of the series, but they are only possible
after the big cleanups.
Changes in v9:
- Link to v8: https://lore.kernel.org/r/20260626-rockchip-usbdp-cleanup-v8-0-47f682987895@collabora.com
- Update DT binding to explicitly mention that port@3 is for the
DP aux channel and not DP in general (Sashiko got this wrong)
- Add a 100ms cooldown sleep in "Drop seamless DP takeover" after HPD
is force disabled (Sashiko)
- Update comment in "Register DP aux bridge" to explain why port@3 is
checked, but port@0 is used (Sashiko)
- Check for high-speed only mode in "Support going from DP-only mode to
USB mode" (Sashiko)
- Add new patch for rk_udphy_reset_deassert error handling (Sashiko)
- Add new patch to avoid enabling USB3 in high-speed only mode during
PHY reinit (Sashiko)
- Add 3 more patches to handle the LCPLL lock issue mentioned in the v8
cover letter after feedback from Rockchip. Apparently the DWC3 does
not cope very well with the PHY disappearing resulting in the PIPE
interface misbehaving, which in turn results in the LCPLL not locking.
The new patches avoid this by asserting DWC3_GUSB3PIPECTL_PHYSOFTRST.
As this assert needs to be done when the PHY wants to reset, a new
notifier system has been implemented to support triggering this from
the PHY driver. This also means, that this version now also involves
the USB subsystem.
- Drop old patch trying to solve the DP-only -> USB mode switch in
favour of 5 new patches completely rewriting and simplifying the
power status handling. The new code ensures that the PHY always
has the right modes enabled and also makes sure a re-init happens
on an orientation change.
- rebased on v7.2-rc1
Changes in v8:
- Link to v7: https://lore.kernel.org/r/20260625-rockchip-usbdp-cleanup-v7-0-38eb3cf654fd@collabora.com
- Move patch "Limit DP lane count to muxed lanes" after single lane
support, which introduces dp_lanes variable to make sure series
is bi-sectable (Sashiko)
- Force disable HPD in "Drop seamless DP takeover" patch and update
patch description to mention potential issues with SErrors for
bootloaders really keeping the DW-DP on. As mentioned in the new
commit message this is untested as I'm not aware of such a
bootloader anyways; this also means we need to keep the HPD GRF
register defines in the 'Drop DP HPD handling' patch (Sashiko)
- Fix mode logic in "Properly handle TYPEC_STATE_SAFE and
TYPEC_STATE_USB" patch; I blame the heat (Sashiko)
- Improve "Support going from DP-only mode to USB mode" patch to
better handle starting in DP only mode; due to TypeC logic
starting delayed this does not really happen, though (Sashiko)
- Improve "Support going from DP-only mode to USB mode" to avoid
checking previous state and instead power on USB state based
on previous requested state to avoid effects from the flip
callback (Sashiko)
- Update the debug message patch to include some more info
- Ad one more patch, which disables USB3 at startup and drops
the -EPROBE_DEFER logic
Changes in v7:
- Link to v6: https://lore.kernel.org/r/20260619-rockchip-usbdp-cleanup-v6-0-3bb1f54b3f35@collabora.com
- Add new patch handling missing clock-names in DT gracefully (Sashiko)
- Add new patch handling rk_udphy_reset_deassert_all errors in init check (Sashiko)
- Add new patch to handle Properly handle TYPEC_STATE_SAFE and TYPEC_STATE_USB (Sashiko)
- Add new patch to avoid xHCI SErrors
Changes in v6:
- Link to v5: https://lore.kernel.org/r/20260612-rockchip-usbdp-cleanup-v5-0-efc83069869f@collabora.com
- Add explicit <linux/string_choices.h> include in last patch (Sashiko)
- Add new patch moving mode_change update after error handling (Sashiko)
- Add new patch fixing error masking of devm_clk_bulk_get_all() (Sashiko)
- Add new patch dropping seamless DP takeover as it is non-functional and buggy (Sashiko)
- Add new patch limiting DP lane count to muxed lanes (Sashiko)
- Add error handling in the patch that keeps clocks running on PHY re-init (Sashiko)
- Also look for DP being configured to second lane for the flip config
in DP single-lane mode, which should at least keep USB working for
this super unusual config (Sashiko)
- Drop useless ret variable in patch introducing guard() for the mutex
- Add error handling for PHY re-enablement in the patch fixing support for
DP-only -> USB mode (Sashiko)
Changes in v5:
- Link to v4: https://lore.kernel.org/r/20260428-rockchip-usbdp-cleanup-v4-0-7775671ece22@collabora.com
- Picked up Acked-by from Rob Herring for DT binding
- Fix typos in commit messages/comments
- Add Fixes tag to "Do not looe USB3 PHY status" patch
- Collect Reviewed-by: Neil Armstrong for multiple patches
- Drop now unused code from "Drop DP HPD handling" patch (Sashiko)
- Ignore mux events not involving DP AltMode (Sashiko)
- Add new patch to support going back from DP only mode to USB combo
mode; technically this is a fix, but DP mode does not yet work
upstream, so it does not matter (Sashiko)
- Add new patch adding a few debug messages, which are useful
to investigate potential hotplug issues in the future
- Sashiko comments about the DT binding and property usage
are wrong as the first port is for the superspeed lanes
used for DP and USB, while the last port is just about
DP aux. I ignored them.
- There is a pre-existing bug, that can already be hit with the
upstream kernel and that the series doesn't fix properly:
Accessing the USB3 controller registers requires the USB PHY
running, since it provides a clock. Re-initializing the PHY
means there is a race-condition - if the system tries to access
the USB3 controller in parallel to the re-init, the system will
hang and/or fail with an SError. By keeping the clocks running
and only asserting the resets this time is minimized by this
series. A proper fix for this will be looked into independently
from this series.
- I used v7.1-rc6 as base, but the driver has no changes since
6.18 even in linux-next and there are no pending patches for
it on the mailinglist either, so it applies to *any* recent
kernel branch.
Changes in v4:
- Link to v3: https://lore.kernel.org/r/20260313-rockchip-usbdp-cleanup-v3-0-3e8fe89a35b5@collabora.com
- rebased to v7.1-rc1 (no changes)
- Update DRM bridge registration patch to avoid registration when DP aux
port is not connected to anything, since this results in errors and some
boards use USBDP instances for USB3 only.
- Add patch renaming mode_change into phy_needs_reinit
- Add patch to re-init PHY on orientation change
- Add patch to factor out lane_mux_sel setup
- Add patch to handle mutex via guard functions
Changes in v3:
- Link to v2: https://lore.kernel.org/r/20260213-rockchip-usbdp-cleanup-v2-0-b67ec225f96e@collabora.com
- Add patch to register the USBDP PHY as DRM bridge
- Add patch to describe ports in DT binding (used by the DRM bridge)
- Add patch to drop HPD handling from the PHY
Changes in v2:
- Link to v1: https://lore.kernel.org/r/20260203-rockchip-usbdp-cleanup-v1-0-16a6f92ed176@collabora.com
- Added new patches to fix USB3 SError
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
Frank Wang (1):
phy: rockchip: usbdp: Amend SSC modulation deviation
Sebastian Reichel (35):
dt-bindings: phy: rockchip-usbdp: add improved ports scheme
phy: rockchip: usbdp: Update mode_change after error handling
phy: rockchip: usbdp: Do not lose USB3 PHY status
phy: rockchip: usbdp: Fix devm_clk_bulk_get_all check
phy: rockchip: usbdp: Handle missing clock-names DT property gracefully
phy: rockchip: usbdp: Drop seamless DP takeover
phy: rockchip: usbdp: Handle rk_udphy_reset_deassert_all errors in init check
phy: rockchip: usbdp: Keep clocks running on PHY re-init
phy: rockchip: usbdp: Add missing mode_change update
phy: rockchip: usbdp: Limit DP lane count to muxed lanes
phy: rockchip: usbdp: Rename DP lane functions
phy: rockchip: usbdp: Use FIELD_PREP_WM16_CONST
phy: rockchip: usbdp: Cleanup DP lane selection function
phy: rockchip: usbdp: Register DP aux bridge
phy: rockchip: usbdp: Drop DP HPD handling
phy: rockchip: usbdp: Rename mode_change to phy_needs_reinit
phy: rockchip: usbdp: Re-init the PHY on orientation change
phy: rockchip: usbdp: Factor out lane_mux_sel setup
phy: rockchip: usbdp: Properly handle TYPEC_STATE_SAFE and TYPEC_STATE_USB
phy: rockchip: usbdp: Use guard functions for mutex
phy: rockchip: usbdp: Clear USB status on PHY exit
phy: rockchip: usbdp: Hold mutex in DP PHY configure
phy: rockchip: usbdp: Add some extra debug messages
phy: rockchip: usbdp: Avoid xHCI SErrors
phy: rockchip: usbdp: Disable USB3 on probe
phy: rockchip: usbdp: Handle rk_udphy_reset_deassert errors
phy: rockchip: usbdp: Only enable USB3 when not in high-speed mode
phy: core: add notifier infrastructure
usb: dwc3: core: support PHY reset notifications
phy: rockchip: usbdp: Add phy reset notification support
phy: rockchip: usbdp: Rename mode to hw_mode
phy: rockchip: usbdp: Simplify power state handling
phy: rockchip: usbdp: Rename phy_needs_reinit to orientation_changed
phy: rockchip: usbdp: Re-init PHY on mux change
phy: rockchip: usbdp: Power optimizations
William Wu (1):
phy: rockchip: usbdp: Fix LFPS detect threshold control
Zhang Yubing (1):
phy: rockchip: usbdp: Support single-lane DP
.../bindings/phy/phy-rockchip-usbdp.yaml | 23 +
drivers/phy/phy-core.c | 57 +++
drivers/phy/rockchip/Kconfig | 2 +
drivers/phy/rockchip/phy-rockchip-usbdp.c | 522 ++++++++++-----------
drivers/usb/dwc3/core.c | 82 ++++
drivers/usb/dwc3/core.h | 16 +
include/linux/phy/phy.h | 40 ++
7 files changed, 470 insertions(+), 272 deletions(-)
---
base-commit: dc59e4fea9d83f03bad6bddf3fa2e52491777482
change-id: 20260203-rockchip-usbdp-cleanup-5b59dfb561a3
Best regards,
--
Sebastian Reichel <sebastian.reichel@collabora.com>
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply
* [PATCH v9 03/38] phy: rockchip: usbdp: Do not lose USB3 PHY status
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
By default (i.e. without manually enabling runtime PM) DWC3 requests the
USB3 PHY once and keeps it enabled all the time. When DisplayPort is
being requested later on, a mode change is needed. This re-initializes
the PHY. During re-initialization the status variable has incorrectly
been cleared, which means the tracking information for USB3 is lost.
This is not an immediate problem, since the DP side keeps the PHY
enabled. But once DP is toggled off, the whole PHY will be disabled.
This is a problem, because the USB side still needs it powered.
Fix things by not clearing the status flags.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 1 -
1 file changed, 1 deletion(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index a5ffdf7a6e76..12dfdd470a78 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1008,7 +1008,6 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
rk_udphy_u3_port_disable(udphy, false);
udphy->mode_change = false;
} else if (udphy->mode_change) {
- udphy->status = UDPHY_MODE_NONE;
if (udphy->mode == UDPHY_MODE_DP)
rk_udphy_u3_port_disable(udphy, true);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 01/38] dt-bindings: phy: rockchip-usbdp: add improved ports scheme
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Currently the Rockchip USBDP PHY is missing a documented port scheme.
Meanwhile upstream RK3588 DTS files are a bit messy and use different
port schemes. The upstream USBDP PHY Linux kernel driver does not yet
parse the ports at all and thus does not create any implicit ABI either.
But with the current mess it is not possible to properly support USB-C
DP AltMode. Thus this introduces a proper port scheme following roughly
the ports design of the Qualcomm QMP USB4-USB3-DP PHY controller binding
with a slight difference that there is an additional port for the
USB-C SBU port as the Rockchip USB-DP PHY also contains the SBU mux.
Reviewed-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
.../bindings/phy/phy-rockchip-usbdp.yaml | 23 ++++++++++++++++++++++
1 file changed, 23 insertions(+)
diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-usbdp.yaml b/Documentation/devicetree/bindings/phy/phy-rockchip-usbdp.yaml
index 8b7059d5b182..c1a1384118da 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-usbdp.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-usbdp.yaml
@@ -114,6 +114,29 @@ properties:
A port node to link the PHY to a TypeC controller for the purpose of
handling orientation switching.
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/properties/port
+ description:
+ Output endpoint of the PHY for USB (or DP when configured into 4 lane
+ mode), which should point to the superspeed port of a USB connector.
+
+ port@1:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Incoming endpoint from the USB controller
+
+ port@2:
+ $ref: /schemas/graph.yaml#/properties/port
+ description: Incoming endpoint from the DisplayPort controller
+
+ port@3:
+ $ref: /schemas/graph.yaml#/properties/port
+ description:
+ Output endpoint of the PHY for DP Auxiliary, which should either point to
+ the SBU port of a USB-C connector or a DisplayPort connector input port.
+
required:
- compatible
- reg
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 02/38] phy: rockchip: usbdp: Update mode_change after error handling
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
If rk_udphy_init() or rk_udphy_setup() fails, the reinit will not be
tried again. Fix this by only updating the variable after all potential
errors have been handled.
Note, that no errors have been seen on real hardware and failures would
most likely be fatal and require at least a full reboot as the function
already asserts the PHY reset lines. So this is more of a theoretical
issue.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612163835.8D5471F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index fba35510d88c..a5ffdf7a6e76 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1000,15 +1000,14 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
}
if (udphy->status == UDPHY_MODE_NONE) {
- udphy->mode_change = false;
ret = rk_udphy_setup(udphy);
if (ret)
return ret;
if (udphy->mode & UDPHY_MODE_USB)
rk_udphy_u3_port_disable(udphy, false);
- } else if (udphy->mode_change) {
udphy->mode_change = false;
+ } else if (udphy->mode_change) {
udphy->status = UDPHY_MODE_NONE;
if (udphy->mode == UDPHY_MODE_DP)
rk_udphy_u3_port_disable(udphy, true);
@@ -1017,6 +1016,7 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
ret = rk_udphy_setup(udphy);
if (ret)
return ret;
+ udphy->mode_change = false;
}
udphy->status |= mode;
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 08/38] phy: rockchip: usbdp: Keep clocks running on PHY re-init
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
When a mode change is required rk_udphy_power_on() disables
the clocks and then calls rk_udphy_setup(), which then enables
all the clocks again before continuing with rk_udphy_init().
Considering that rk_udphy_init() does assert the reset lines,
re-enabling the clocks is just delaying things. Avoid it by
directly calling rk_udphy_init().
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 5d0e4f82de2f..2b27fd1c15d8 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1022,8 +1022,7 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
if (udphy->mode == UDPHY_MODE_DP)
rk_udphy_u3_port_disable(udphy, true);
- rk_udphy_disable(udphy);
- ret = rk_udphy_setup(udphy);
+ ret = rk_udphy_init(udphy);
if (ret)
return ret;
udphy->mode_change = false;
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 05/38] phy: rockchip: usbdp: Handle missing clock-names DT property gracefully
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
The rk_udphy_clk_init() function would currently try to do a strncmp for
a NULL pointer, if DT specifies 'clocks' property, but no 'clock-names'
property. Fix this by making sure the clock has an id string set.
Note that DT binding requires setting clock-names, so this is only a
problem when booting a non-compliant device tree.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/message/20260619154349.071321F000E9%40smtp.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 2845a012eafc..3fc8222fcaec 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -432,6 +432,9 @@ static int rk_udphy_clk_init(struct rk_udphy *udphy, struct device *dev)
/* used for configure phy reference clock frequency */
for (i = 0; i < udphy->num_clks; i++) {
+ if (!udphy->clks[i].id)
+ continue;
+
if (!strncmp(udphy->clks[i].id, "refclk", 6)) {
udphy->refclk = udphy->clks[i].clk;
break;
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 06/38] phy: rockchip: usbdp: Drop seamless DP takeover
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Right now the DRM drivers do not support seamless DP takeover and I'm
I'm not aware of any bootloader implementing this feature either.
In any case this feature would be limited to boards using the USBDP PHY
for a DP or eDP connection instead of the more commonly USB-C connector.
With USB-C's DP AltMode a seamless DP takeover requires handing over the
state of the TCPM state machine from the bootloader to the kernel. This
in turn requires a huge amount of work to keep the state machine
implementations synchronized. It's very unlikely we will see somebody
implementing that in the foreseeable future.
As the current code is obviously buggy and untested, let's simply drop
support for seamless DP takeover. It can be re-implemented cleanly once
somebody adds all missing bits.
Technically the VOP side should be disabled first to avoid data being
send to an unpowered PHY from the running pipeline. As a workaround this
force disables HPD. I'm not sure if this would be good enough, but cannot
test as there is no support in the bootloaders known to me and my test
boards route USBDP to USB-C connectors.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612164107.C7DB21F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 13 +++++++++----
1 file changed, 9 insertions(+), 4 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 3fc8222fcaec..d73455370113 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -926,6 +926,7 @@ static int rk_udphy_parse_lane_mux_data(struct rk_udphy *udphy)
static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
{
+ const struct rk_udphy_cfg *cfg = udphy->cfgs;
int ret;
u32 value;
@@ -938,10 +939,14 @@ static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
rk_udphy_reset_deassert_all(udphy);
regmap_read(udphy->pma_regmap, CMN_LANE_MUX_AND_EN_OFFSET, &value);
- if (FIELD_GET(CMN_DP_LANE_MUX_ALL, value) && FIELD_GET(CMN_DP_LANE_EN_ALL, value))
- udphy->status = UDPHY_MODE_DP;
- else
- rk_udphy_disable(udphy);
+ if (FIELD_GET(CMN_DP_LANE_MUX_ALL, value) && FIELD_GET(CMN_DP_LANE_EN_ALL, value)) {
+ dev_info(udphy->dev, "Started with DP PHY pre-enabled; seamless takeover unsupported\n");
+ rk_udphy_grfreg_write(udphy->vogrf, &cfg->vogrfcfg[udphy->id].hpd_trigger, false);
+ /* Wait for VOP side to shut up */
+ msleep(100);
+ }
+
+ rk_udphy_disable(udphy);
return 0;
}
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 09/38] phy: rockchip: usbdp: Amend SSC modulation deviation
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
From: Frank Wang <frank.wang@rock-chips.com>
Move SSC modulation deviation into private config of clock
- 24M: 0x00d4[5:0] = 0x30
- 26M: 0x00d4[5:0] = 0x33
Signed-off-by: Frank Wang <frank.wang@rock-chips.com>
[Taken over from rockchip's kernel tree; register 0x00d4 is not
described in the TRM]
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 2b27fd1c15d8..923279ed7d77 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -350,7 +350,8 @@ static const struct reg_sequence rk_udphy_24m_refclk_cfg[] = {
{0x0a64, 0xa8}, {0x1a3c, 0xd0},
{0x1a44, 0xd0}, {0x1a48, 0x01},
{0x1a4c, 0x0d}, {0x1a54, 0xe0},
- {0x1a5c, 0xe0}, {0x1a64, 0xa8}
+ {0x1a5c, 0xe0}, {0x1a64, 0xa8},
+ {0x00d4, 0x30}
};
static const struct reg_sequence rk_udphy_26m_refclk_cfg[] = {
@@ -377,7 +378,7 @@ static const struct reg_sequence rk_udphy_26m_refclk_cfg[] = {
{0x0c30, 0x0e}, {0x0c48, 0x06},
{0x1c30, 0x0e}, {0x1c48, 0x06},
{0x028c, 0x18}, {0x0af0, 0x00},
- {0x1af0, 0x00}
+ {0x1af0, 0x00}, {0x00d4, 0x33}
};
static const struct reg_sequence rk_udphy_init_sequence[] = {
@@ -412,8 +413,7 @@ static const struct reg_sequence rk_udphy_init_sequence[] = {
{0x0070, 0x7d}, {0x0074, 0x68},
{0x0af4, 0x1a}, {0x1af4, 0x1a},
{0x0440, 0x3f}, {0x10d4, 0x08},
- {0x20d4, 0x08}, {0x00d4, 0x30},
- {0x0024, 0x6e},
+ {0x20d4, 0x08}, {0x0024, 0x6e}
};
static inline int rk_udphy_grfreg_write(struct regmap *base,
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 07/38] phy: rockchip: usbdp: Handle rk_udphy_reset_deassert_all errors in init check
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Fix theoretical issue, that failure to deassert the reset lines would
result in an SError in follow-up register access. Note, that this cannot
happen with current code, since the Rockchip reset driver never returns
any errors for (de)asserting reset lines.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/message/20260619154903.2225A1F000E9%40smtp.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 7 +++++--
1 file changed, 5 insertions(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index d73455370113..5d0e4f82de2f 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -936,7 +936,9 @@ static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
return ret;
}
- rk_udphy_reset_deassert_all(udphy);
+ ret = rk_udphy_reset_deassert_all(udphy);
+ if (ret)
+ goto exit;
regmap_read(udphy->pma_regmap, CMN_LANE_MUX_AND_EN_OFFSET, &value);
if (FIELD_GET(CMN_DP_LANE_MUX_ALL, value) && FIELD_GET(CMN_DP_LANE_EN_ALL, value)) {
@@ -946,9 +948,10 @@ static int rk_udphy_get_initial_status(struct rk_udphy *udphy)
msleep(100);
}
+exit:
rk_udphy_disable(udphy);
- return 0;
+ return ret;
}
static int rk_udphy_parse_dt(struct rk_udphy *udphy)
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 14/38] phy: rockchip: usbdp: Rename DP lane functions
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
The common prefix for DisplayPort related functions is rk_udphy_dp_
(with a final _), so update the two DP lane functions to follow that
scheme.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 0cfd23a405cb..ee7ec86bda9e 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -550,7 +550,7 @@ static void rk_udphy_usb_bvalid_enable(struct rk_udphy *udphy, u8 enable)
* ---------------------------------------------------------------------------
*/
-static void rk_udphy_dplane_select(struct rk_udphy *udphy)
+static void rk_udphy_dp_lane_select(struct rk_udphy *udphy)
{
const struct rk_udphy_cfg *cfg = udphy->cfgs;
u32 value = 0;
@@ -579,7 +579,7 @@ static void rk_udphy_dplane_select(struct rk_udphy *udphy)
FIELD_PREP(DP_AUX_DOUT_SEL, udphy->dp_aux_dout_sel) | value);
}
-static void rk_udphy_dplane_enable(struct rk_udphy *udphy, int dp_lanes)
+static void rk_udphy_dp_lane_enable(struct rk_udphy *udphy, int dp_lanes)
{
u32 val = 0;
int i;
@@ -1084,9 +1084,9 @@ static int rk_udphy_dp_phy_power_on(struct phy *phy)
if (ret)
goto unlock;
- rk_udphy_dplane_enable(udphy, udphy->dp_lanes);
+ rk_udphy_dp_lane_enable(udphy, udphy->dp_lanes);
- rk_udphy_dplane_select(udphy);
+ rk_udphy_dp_lane_select(udphy);
unlock:
mutex_unlock(&udphy->mutex);
@@ -1104,7 +1104,7 @@ static int rk_udphy_dp_phy_power_off(struct phy *phy)
struct rk_udphy *udphy = phy_get_drvdata(phy);
mutex_lock(&udphy->mutex);
- rk_udphy_dplane_enable(udphy, 0);
+ rk_udphy_dp_lane_enable(udphy, 0);
rk_udphy_power_off(udphy, UDPHY_MODE_DP);
mutex_unlock(&udphy->mutex);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 13/38] phy: rockchip: usbdp: Limit DP lane count to muxed lanes
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
In theory the DP controller could request 4 lanes when the PHY is
restricted to 2 lanes as the other half is used by USB3.
With the current user (DW-DP) this cannot happen, but as the check is
cheap and users might change in the future protect things accordingly.
Not doing so would corrupt USB3 usage by the following code configuring
the voltages.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612165546.98E1F1F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index da15178d7f16..0cfd23a405cb 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1134,6 +1134,9 @@ static int rk_udphy_dp_phy_verify_link_rate(struct rk_udphy *udphy,
static int rk_udphy_dp_phy_verify_lanes(struct rk_udphy *udphy,
struct phy_configure_opts_dp *dp)
{
+ if (dp->lanes > udphy->dp_lanes)
+ return -EINVAL;
+
switch (dp->lanes) {
case 1:
case 2:
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 16/38] phy: rockchip: usbdp: Cleanup DP lane selection function
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Use FIELD_PREP_WM16() helpers to simplify the DP lane selection
logic.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 28 +++++++---------------------
1 file changed, 7 insertions(+), 21 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 3124bcfed031..5d3db696d51f 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -553,30 +553,16 @@ static void rk_udphy_usb_bvalid_enable(struct rk_udphy *udphy, u8 enable)
static void rk_udphy_dp_lane_select(struct rk_udphy *udphy)
{
const struct rk_udphy_cfg *cfg = udphy->cfgs;
- u32 value = 0;
-
- switch (udphy->dp_lanes) {
- case 4:
- value |= 3 << udphy->dp_lane_sel[3] * 2;
- value |= 2 << udphy->dp_lane_sel[2] * 2;
- fallthrough;
-
- case 2:
- value |= 1 << udphy->dp_lane_sel[1] * 2;
- fallthrough;
+ u32 value = FIELD_PREP_WM16(DP_LANE_SEL_ALL, 0);
+ int i;
- case 1:
- value |= 0 << udphy->dp_lane_sel[0] * 2;
- break;
+ for (i = 0; i < udphy->dp_lanes; i++)
+ value |= field_prep(DP_LANE_SEL_N(udphy->dp_lane_sel[i]), i);
- default:
- break;
- }
+ value |= FIELD_PREP_WM16(DP_AUX_DIN_SEL, udphy->dp_aux_din_sel);
+ value |= FIELD_PREP_WM16(DP_AUX_DOUT_SEL, udphy->dp_aux_dout_sel);
- regmap_write(udphy->vogrf, cfg->vogrfcfg[udphy->id].dp_lane_reg,
- ((DP_AUX_DIN_SEL | DP_AUX_DOUT_SEL | DP_LANE_SEL_ALL) << 16) |
- FIELD_PREP(DP_AUX_DIN_SEL, udphy->dp_aux_din_sel) |
- FIELD_PREP(DP_AUX_DOUT_SEL, udphy->dp_aux_dout_sel) | value);
+ regmap_write(udphy->vogrf, cfg->vogrfcfg[udphy->id].dp_lane_reg, value);
}
static void rk_udphy_dp_lane_enable(struct rk_udphy *udphy, int dp_lanes)
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 12/38] phy: rockchip: usbdp: Support single-lane DP
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
From: Zhang Yubing <yubing.zhang@rock-chips.com>
Implement support for using just a single DisplayPort line.
Signed-off-by: Zhang Yubing <yubing.zhang@rock-chips.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 64 +++++++++++++------------------
1 file changed, 27 insertions(+), 37 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 6333b5cc7151..da15178d7f16 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -193,6 +193,7 @@ struct rk_udphy {
int id;
bool dp_in_use;
+ int dp_lanes;
/* PHY const config */
const struct rk_udphy_cfg *cfgs;
@@ -540,6 +541,13 @@ static void rk_udphy_usb_bvalid_enable(struct rk_udphy *udphy, u8 enable)
* <0 1> dpln0 dpln1 usbrx usbtx
* <2 3> usbrx usbtx dpln0 dpln1
* ---------------------------------------------------------------------------
+ * if 1 lane for dp function, 2 lane for usb function, define rockchip,dp-lane-mux = <x>;
+ * sample as follow:
+ * ---------------------------------------------------------------------------
+ * B11-B10 A2-A3 A11-A10 B2-B3
+ * rockchip,dp-lane-mux ln0(tx/rx) ln1(tx) ln2(tx/rx) ln3(tx)
+ * <0> dpln0 \ usbrx usbtx
+ * ---------------------------------------------------------------------------
*/
static void rk_udphy_dplane_select(struct rk_udphy *udphy)
@@ -547,18 +555,18 @@ static void rk_udphy_dplane_select(struct rk_udphy *udphy)
const struct rk_udphy_cfg *cfg = udphy->cfgs;
u32 value = 0;
- switch (udphy->mode) {
- case UDPHY_MODE_DP:
- value |= 2 << udphy->dp_lane_sel[2] * 2;
+ switch (udphy->dp_lanes) {
+ case 4:
value |= 3 << udphy->dp_lane_sel[3] * 2;
+ value |= 2 << udphy->dp_lane_sel[2] * 2;
fallthrough;
- case UDPHY_MODE_DP_USB:
- value |= 0 << udphy->dp_lane_sel[0] * 2;
+ case 2:
value |= 1 << udphy->dp_lane_sel[1] * 2;
- break;
+ fallthrough;
- case UDPHY_MODE_USB:
+ case 1:
+ value |= 0 << udphy->dp_lane_sel[0] * 2;
break;
default:
@@ -571,28 +579,6 @@ static void rk_udphy_dplane_select(struct rk_udphy *udphy)
FIELD_PREP(DP_AUX_DOUT_SEL, udphy->dp_aux_dout_sel) | value);
}
-static int rk_udphy_dplane_get(struct rk_udphy *udphy)
-{
- int dp_lanes;
-
- switch (udphy->mode) {
- case UDPHY_MODE_DP:
- dp_lanes = 4;
- break;
-
- case UDPHY_MODE_DP_USB:
- dp_lanes = 2;
- break;
-
- case UDPHY_MODE_USB:
- default:
- dp_lanes = 0;
- break;
- }
-
- return dp_lanes;
-}
-
static void rk_udphy_dplane_enable(struct rk_udphy *udphy, int dp_lanes)
{
u32 val = 0;
@@ -662,6 +648,7 @@ static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
}
rk_udphy_mode_set(udphy, UDPHY_MODE_DP_USB);
+ udphy->dp_lanes = 2;
}
static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
@@ -900,7 +887,7 @@ static int rk_udphy_parse_lane_mux_data(struct rk_udphy *udphy)
return 0;
}
- if (num_lanes != 2 && num_lanes != 4)
+ if (num_lanes != 1 && num_lanes != 2 && num_lanes != 4)
return dev_err_probe(udphy->dev, -EINVAL,
"invalid number of lane mux\n");
@@ -926,9 +913,11 @@ static int rk_udphy_parse_lane_mux_data(struct rk_udphy *udphy)
}
udphy->mode = UDPHY_MODE_DP;
- if (num_lanes == 2) {
+ udphy->dp_lanes = num_lanes;
+ if (num_lanes == 1 || num_lanes == 2) {
udphy->mode |= UDPHY_MODE_USB;
- udphy->flip = (udphy->lane_mux_sel[0] == PHY_LANE_MUX_DP);
+ udphy->flip = (udphy->lane_mux_sel[0] == PHY_LANE_MUX_DP) ||
+ (udphy->lane_mux_sel[1] == PHY_LANE_MUX_DP);
}
return 0;
@@ -1085,18 +1074,17 @@ static int rk_udphy_dp_phy_exit(struct phy *phy)
static int rk_udphy_dp_phy_power_on(struct phy *phy)
{
struct rk_udphy *udphy = phy_get_drvdata(phy);
- int ret, dp_lanes;
+ int ret;
mutex_lock(&udphy->mutex);
- dp_lanes = rk_udphy_dplane_get(udphy);
- phy_set_bus_width(phy, dp_lanes);
+ phy_set_bus_width(phy, udphy->dp_lanes);
ret = rk_udphy_power_on(udphy, UDPHY_MODE_DP);
if (ret)
goto unlock;
- rk_udphy_dplane_enable(udphy, dp_lanes);
+ rk_udphy_dplane_enable(udphy, udphy->dp_lanes);
rk_udphy_dplane_select(udphy);
@@ -1376,6 +1364,7 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
udphy->lane_mux_sel[2] = PHY_LANE_MUX_DP;
udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
mode = UDPHY_MODE_DP;
+ udphy->dp_lanes = 4;
break;
case TYPEC_DP_STATE_D:
@@ -1392,6 +1381,7 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
udphy->lane_mux_sel[3] = PHY_LANE_MUX_DP;
}
mode = UDPHY_MODE_DP_USB;
+ udphy->dp_lanes = 2;
break;
}
@@ -1540,7 +1530,7 @@ static int rk_udphy_probe(struct platform_device *pdev)
ret = PTR_ERR(udphy->phy_dp);
return dev_err_probe(dev, ret, "failed to create DP phy\n");
}
- phy_set_bus_width(udphy->phy_dp, rk_udphy_dplane_get(udphy));
+ phy_set_bus_width(udphy->phy_dp, udphy->dp_lanes);
udphy->phy_dp->attrs.max_link_rate = 8100;
phy_set_drvdata(udphy->phy_dp, udphy);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 10/38] phy: rockchip: usbdp: Fix LFPS detect threshold control
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, William Wu
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
From: William Wu <william.wu@rock-chips.com>
According to the LFPS Tx Low Power/LFPS Rx Detect Threshold [1],
the device under test(DUT) must not respond if LFPS below the
minimum LFPS Rx Detect Threshold 100mV. Test fail on Rockchip
platforms, because the default LFPS detect threshold is set to
65mV.
The USBDP PHY LFPS detect threshold voltage could be set to
30mV ~ 140mV, and since there could be 10-20% PVT variation,
we set LFPS detect threshold voltage to 110mV.
[1] https://compliance.usb.org/resources/LFPS_Rx_Tx_Low_Power_Compliance_Update_Rev5.pdf
Signed-off-by: William Wu <william.wu@rock-chips.com>
[Taken over from rockchip's kernel tree; the registers are not described
in the TRM]
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 923279ed7d77..8202abab4274 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -413,7 +413,8 @@ static const struct reg_sequence rk_udphy_init_sequence[] = {
{0x0070, 0x7d}, {0x0074, 0x68},
{0x0af4, 0x1a}, {0x1af4, 0x1a},
{0x0440, 0x3f}, {0x10d4, 0x08},
- {0x20d4, 0x08}, {0x0024, 0x6e}
+ {0x20d4, 0x08}, {0x0024, 0x6e},
+ {0x09c0, 0x0a}, {0x19c0, 0x0a}
};
static inline int rk_udphy_grfreg_write(struct regmap *base,
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 11/38] phy: rockchip: usbdp: Add missing mode_change update
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
rk_udphy_set_typec_default_mapping() updates the available modes,
but does not set the mode_change as required. This results in
missing re-initialization and thus non-working DisplayPort.
Fix this issue by introducing a new helper to update the available
modes.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 16 +++++++++++-----
1 file changed, 11 insertions(+), 5 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 8202abab4274..6333b5cc7151 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -622,6 +622,15 @@ static void rk_udphy_dp_hpd_event_trigger(struct rk_udphy *udphy, bool hpd)
rk_udphy_grfreg_write(udphy->vogrf, &cfg->vogrfcfg[udphy->id].hpd_trigger, hpd);
}
+static void rk_udphy_mode_set(struct rk_udphy *udphy, u8 mode)
+{
+ if (udphy->mode == mode)
+ return;
+
+ udphy->mode_change = true;
+ udphy->mode = mode;
+}
+
static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
{
if (udphy->flip) {
@@ -652,7 +661,7 @@ static void rk_udphy_set_typec_default_mapping(struct rk_udphy *udphy)
gpiod_set_value_cansleep(udphy->sbu2_dc_gpio, 1);
}
- udphy->mode = UDPHY_MODE_DP_USB;
+ rk_udphy_mode_set(udphy, UDPHY_MODE_DP_USB);
}
static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
@@ -1396,10 +1405,7 @@ static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
usleep_range(750, 800);
rk_udphy_dp_hpd_event_trigger(udphy, true);
} else if (data->status & DP_STATUS_HPD_STATE) {
- if (udphy->mode != mode) {
- udphy->mode = mode;
- udphy->mode_change = true;
- }
+ rk_udphy_mode_set(udphy, mode);
rk_udphy_dp_hpd_event_trigger(udphy, true);
} else {
rk_udphy_dp_hpd_event_trigger(udphy, false);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 15/38] phy: rockchip: usbdp: Use FIELD_PREP_WM16_CONST
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Cleanup code by replacing open-coded version of FIELD_PREP_WM16_CONST
with the existing helper macro.
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index ee7ec86bda9e..3124bcfed031 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -12,6 +12,7 @@
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/gpio.h>
+#include <linux/hw_bitfield.h>
#include <linux/mfd/syscon.h>
#include <linux/mod_devicetable.h>
#include <linux/module.h>
@@ -75,7 +76,6 @@
#define TRSV_LN2_MON_RX_CDR_DONE_OFFSET 0x1b84 /* trsv_reg06E1 */
#define TRSV_LN2_MON_RX_CDR_LOCK_DONE BIT(0)
-#define BIT_WRITEABLE_SHIFT 16
#define PHY_AUX_DP_DATA_POL_NORMAL 0
#define PHY_AUX_DP_DATA_POL_INVERT 1
#define PHY_LANE_MUX_USB 0
@@ -104,8 +104,8 @@ struct rk_udphy_grf_reg {
#define _RK_UDPHY_GEN_GRF_REG(offset, mask, disable, enable) \
{\
offset, \
- FIELD_PREP_CONST(mask, disable) | (mask << BIT_WRITEABLE_SHIFT), \
- FIELD_PREP_CONST(mask, enable) | (mask << BIT_WRITEABLE_SHIFT), \
+ FIELD_PREP_WM16_CONST(mask, disable), \
+ FIELD_PREP_WM16_CONST(mask, enable), \
}
#define RK_UDPHY_GEN_GRF_REG(offset, bitend, bitstart, disable, enable) \
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 20/38] phy: rockchip: usbdp: Re-init the PHY on orientation change
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Changing the cable orientation reconfigures the lane muxing, which
requires re-initializing the PHY. Without this DP functionality
breaks, if the cable is re-plugged with swapped orientation.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 8f06bb9b1fcb..eab9e82dbfe4 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -626,6 +626,7 @@ static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
enum typec_orientation orien)
{
struct rk_udphy *udphy = typec_switch_get_drvdata(sw);
+ bool flipped = orien == TYPEC_ORIENTATION_REVERSE;
mutex_lock(&udphy->mutex);
@@ -637,7 +638,10 @@ static int rk_udphy_orien_sw_set(struct typec_switch_dev *sw,
goto unlock_ret;
}
- udphy->flip = orien == TYPEC_ORIENTATION_REVERSE;
+ if (udphy->flip != flipped)
+ udphy->phy_needs_reinit = true;
+
+ udphy->flip = flipped;
rk_udphy_set_typec_default_mapping(udphy);
rk_udphy_usb_bvalid_enable(udphy, true);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 19/38] phy: rockchip: usbdp: Rename mode_change to phy_needs_reinit
From: Sebastian Reichel @ 2026-07-01 23:35 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Right now the mode_change property is set whenever the mode changes
between USB-only, DP-only and USB-DP. It is needed, because on any
mode change the PHY needs to be re-initialized. Apparently at least
DP also requires a re-init when the cable orientation is changed,
which is currently not being done (except when the orientation switch
also involves a mode change). Prepare for this by renaming mode_change
to phy_needs_reinit.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 10 +++++-----
1 file changed, 5 insertions(+), 5 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 928466659486..8f06bb9b1fcb 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -172,7 +172,7 @@ struct rk_udphy {
/* PHY status management */
bool flip;
- bool mode_change;
+ bool phy_needs_reinit;
u8 mode;
u8 status;
@@ -584,7 +584,7 @@ static void rk_udphy_mode_set(struct rk_udphy *udphy, u8 mode)
if (udphy->mode == mode)
return;
- udphy->mode_change = true;
+ udphy->phy_needs_reinit = true;
udphy->mode = mode;
}
@@ -987,15 +987,15 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
if (udphy->mode & UDPHY_MODE_USB)
rk_udphy_u3_port_disable(udphy, false);
- udphy->mode_change = false;
- } else if (udphy->mode_change) {
+ udphy->phy_needs_reinit = false;
+ } else if (udphy->phy_needs_reinit) {
if (udphy->mode == UDPHY_MODE_DP)
rk_udphy_u3_port_disable(udphy, true);
ret = rk_udphy_init(udphy);
if (ret)
return ret;
- udphy->mode_change = false;
+ udphy->phy_needs_reinit = false;
}
udphy->status |= mode;
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 27/38] phy: rockchip: usbdp: Avoid xHCI SErrors
From: Sebastian Reichel @ 2026-07-01 23:36 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
The USBDP PHY provides the PIPE clock to the USB3 controller, which
means the PHY must be fully running when anything tries to access
the xHCI registers.
When switching between USB3-only, USB3 + DP and DP-only mode, the
PHY must be re-initialized resulting in a short period of the PHY
being disabled. If the DWC3 driver decides to access the xHCI at
this point the system will fail with an SError.
This patch avoids the problems by disabling the USB3 port before
re-initializing it. This does a couple of things:
- forces phystatus to 0 from GRF (not from PHY)
- switches PIPE clock source from PHY to UTMI (safe fallback clock)
- num_u3_port=0
The last part will be ignored, as DWC3 already probed, but the
clock re-routing will avoid the SError. There is a small delay
afterwards to make sure the mux happened. The datasheet gives
no hints how long it takes, so delay time is a guess.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 6b0add354880..146edd35cf83 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1036,8 +1036,8 @@ static int rk_udphy_power_on(struct rk_udphy *udphy, u8 mode)
rk_udphy_u3_port_disable(udphy, false);
udphy->phy_needs_reinit = false;
} else if (udphy->phy_needs_reinit) {
- if (udphy->mode == UDPHY_MODE_DP)
- rk_udphy_u3_port_disable(udphy, true);
+ rk_udphy_u3_port_disable(udphy, true);
+ udelay(10);
ret = rk_udphy_init(udphy);
if (ret)
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 22/38] phy: rockchip: usbdp: Properly handle TYPEC_STATE_SAFE and TYPEC_STATE_USB
From: Sebastian Reichel @ 2026-07-01 23:36 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Handle TYPEC_STATE_SAFE and TYPEC_STATE_USB Type-C state events,
so that the muxing is properly updated when exiting DP AltMode.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/message/20260619155020.CC7361F000E9%40smtp.kernel.org
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 21 +++++++++++++++------
1 file changed, 15 insertions(+), 6 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 70ef02c4a187..9f0c0127e6d0 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1329,17 +1329,26 @@ static const struct phy_ops rk_udphy_usb3_phy_ops = {
.owner = THIS_MODULE,
};
+static bool rk_udphy_is_supported_mode(struct typec_mux_state *state)
+{
+ /* Handle Safe State and USB State */
+ if (state->mode < TYPEC_STATE_MODAL)
+ return true;
+
+ /* Handle DP AltMode */
+ if (state->alt && state->alt->svid == USB_TYPEC_DP_SID)
+ return true;
+
+ return false;
+}
+
static int rk_udphy_typec_mux_set(struct typec_mux_dev *mux,
struct typec_mux_state *state)
{
struct rk_udphy *udphy = typec_mux_get_drvdata(mux);
- /*
- * Ignore mux events not involving DP AltMode, because
- * the mode field is being reused, e.g. state->mode == 4
- * could be either TYPEC_MODE_USB4 or TYPEC_DP_STATE_C.
- */
- if (!state->alt || state->alt->svid != USB_TYPEC_DP_SID)
+ /* Ignore mux events not involving USB or DP */
+ if (!rk_udphy_is_supported_mode(state))
return 0;
mutex_lock(&udphy->mutex);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 25/38] phy: rockchip: usbdp: Hold mutex in DP PHY configure
From: Sebastian Reichel @ 2026-07-01 23:36 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
rk_udphy_dp_phy_configure() accesses some variables from the struct
rk_udphy, which are updated independently from the USB-C framework.
The USB-C mux/orientation switch functions already hold a mutex to
ensure mutual exclusive access to the struct rk_udphy states, so
simply hold the same one in the DP PHY configuration function.
Reproducing problems due to this on real hardware would be really hard,
but could be possible when quickly re-connecting the USB-C connector.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://lore.kernel.org/linux-phy/20260612164627.23D391F000E9@smtp.kernel.org/
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index 1a983c1cef4b..c874dfeeece9 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1190,6 +1190,8 @@ static int rk_udphy_dp_phy_configure(struct phy *phy,
u32 i, val, lane;
int ret;
+ guard(mutex)(&udphy->mutex);
+
if (dp->set_rate) {
ret = rk_udphy_dp_phy_verify_link_rate(udphy, dp);
if (ret)
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
* [PATCH v9 24/38] phy: rockchip: usbdp: Clear USB status on PHY exit
From: Sebastian Reichel @ 2026-07-01 23:36 UTC (permalink / raw)
To: Vinod Koul, Neil Armstrong, Heiko Stuebner, Frank Wang,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Thinh Nguyen,
Greg Kroah-Hartman
Cc: Andy Yan, Dmitry Baryshkov, Yubing Zhang, Alexey Charkov,
linux-phy, linux-arm-kernel, linux-rockchip, linux-kernel, kernel,
devicetree, linux-usb, Sebastian Reichel, Sashiko
In-Reply-To: <20260702-rockchip-usbdp-cleanup-v9-0-e31efbb62d2e@collabora.com>
Ensure the USB status flag is cleared when the USB3 PHY is
exited while the system is in DP-only mode. This can happen
if the USB3 controller device is unbound while a DP-only
adapter is plugged into the USB-C port.
Fixes: 2f70bbddeb45 ("phy: rockchip: add usbdp combo phy driver")
Reported-by: Sashiko <sashiko-bot@kernel.org>
Closes: https://sashiko.dev/#/message/20260625-rockchip-usbdp-cleanup-v7-24-38eb3cf654fd%40collabora.com
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
drivers/phy/rockchip/phy-rockchip-usbdp.c | 4 +++-
1 file changed, 3 insertions(+), 1 deletion(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-usbdp.c b/drivers/phy/rockchip/phy-rockchip-usbdp.c
index bf6e7edbe631..1a983c1cef4b 100644
--- a/drivers/phy/rockchip/phy-rockchip-usbdp.c
+++ b/drivers/phy/rockchip/phy-rockchip-usbdp.c
@@ -1309,8 +1309,10 @@ static int rk_udphy_usb3_phy_exit(struct phy *phy)
guard(mutex)(&udphy->mutex);
/* DP only or high-speed */
- if (!(udphy->mode & UDPHY_MODE_USB) || udphy->hs)
+ if (!(udphy->mode & UDPHY_MODE_USB) || udphy->hs) {
+ udphy->status &= ~UDPHY_MODE_USB;
return 0;
+ }
rk_udphy_power_off(udphy, UDPHY_MODE_USB);
--
2.53.0
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox