From: sashiko-bot@kernel.org
To: "Krishna Chaitanya Chundru" <krishna.chundru@oss.qualcomm.com>
Cc: linux-pci@vger.kernel.org, devicetree@vger.kernel.org,
linux-phy@lists.infradead.org, robh@kernel.org,
conor+dt@kernel.org, vkoul@kernel.org, neil.armstrong@linaro.org,
olteanv@gmail.com
Subject: Re: [PATCH 11/11] arm64: dts: qcom: nord: Add PCIe endpoint nodes
Date: Sun, 22 Nov 2026 03:17:02 +0000 [thread overview]
Message-ID: <sashiko-outbox-227667@kernel.org> (raw)
In-Reply-To: <20261122-nord_ep-v1-11-6d8839ffa9aa@oss.qualcomm.com>
Thank you for your contribution! Sashiko AI review found 6 potential
issues to consider:
- [High] arm64: dts: qcom: nord: overlapping atu and msix reg regions in
pcie0_ep
- [High] arm64: dts: qcom: nord: non-power-of-2 msix BAR size in
pcie0_ep
- [High] arm64: dts: qcom: nord: missing msix reg region in
pcie1_ep..pcie3_ep
- [Medium] arm64: dts: qcom: nord: missing num-lanes = <8> property in
pcie0_ep
- [Medium] arm64: dts: qcom: nord: 1 MB addr_space reg size in
pcie1_ep..pcie3_ep
- [Low] arm64: dts: qcom: nord: missing gpio.h include in
nord-embedded.dtsi
--
commit 2599e7213b15292427fa12c65b538dbb750cb433
Author: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
arm64: dts: qcom: nord: Add PCIe endpoint nodes
This commit adds the pcie0_ep..pcie3_ep endpoint controller nodes and
their pin control states for the four PCIe instances on Nord.
> diff --git a/arch/arm64/boot/dts/qcom/nord-embedded.dtsi b/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
> index e6d0bd21744e2..829fc63681c1d 100644
> --- a/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
> +++ b/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
> @@ -1638,6 +1638,287 @@ pcie_phy: phy@1b00000 {
> status = "disabled";
> };
>
> + pcie0_ep: pcie-ep@1b80000 {
> + compatible = "qcom,nord-pcie-ep";
> +
> + reg = <0x00 0x01b80000 0x00 0x00004000>,
> + <0x00 0x40000000 0x00 0x00000f20>,
> + <0x00 0x40000f20 0x00 0x000000a8>,
> + <0x00 0x40010000 0x00 0x00020000>,
[Severity: High]
Should the atu region size in pcie0_ep be 0x00010000 (like
pcie1_ep..pcie3_ep) instead of 0x00020000?
With a size of 0x00020000, the atu region spans 0x40010000..0x4002ffff and
overlaps the msix region at 0x40020000..0x400213ff.
dw_pcie_get_resources() claims the full range in iomem_resource via
devm_ioremap_resource() and sets pci->atu_size = 0x20000, which causes
dw_pcie_iatu_detect() to probe unrolled iATU indices 128..255 at
0x40020000..0x4002ffff and write test patterns (0x11110000) into the MSI-X
BAR memory space.
> + <0x00 0x40100000 0x00 0x0ff00000>,
> + <0x00 0x01b84000 0x00 0x00001000>,
> + <0x00 0x40030000 0x00 0x00010000>,
> + <0x00 0x40020000 0x00 0x00001400>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "addr_space",
> + "mmio",
> + "dma",
> + "msix";
[Severity: High]
Does the 0x00001400 msix region size cause pci_epc_set_bar() to fail with
-EINVAL?
pci_epf_mhi_bind() records resource_size(res) of the "msix" resource as
epf_mhi->msix_size, and pci_epf_mhi_epc_init() passes that directly as
msix_bar->size to pci_epc_set_bar(), which requires a power-of-2 BAR size:
drivers/pci/endpoint/pci-epc-core.c:pci_epc_set_bar() {
...
if (!is_power_of_2(epf_bar->size))
return -EINVAL;
...
}
[ ... ]
> + phys = <&pcie_phy 0>;
> + phy-names = "pciephy";
> +
> + reset-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
> + wake-gpios = <&tlmm 0 GPIO_ACTIVE_LOW>;
[Severity: Low]
These nodes introduce the first uses of GPIO_ACTIVE_LOW in
nord-embedded.dtsi, but neither nord-embedded.dtsi nor nord.dtsi includes
<dt-bindings/gpio/gpio.h>. Should nord-embedded.dtsi include
<dt-bindings/gpio/gpio.h> directly so it does not depend on inclusion order
in board .dts files?
> +
> + pinctrl-0 = <&pcie0_ep_default>;
> + pinctrl-names = "default";
> +
> + linux,pci-domain = <0>;
> +
> + status = "disabled";
> + };
[Severity: Medium]
Is pcie0_ep missing num-lanes = <8>?
On Nord, pcie0 in nord.dtsi is the 8-lane port of the quadfurcated PHY and
specifies num-lanes = <8>, while pcie1_ep..pcie3_ep below specify
num-lanes = <4>, <2>, and <2>. Without num-lanes on pcie0_ep,
dw_pcie_get_resources() leaves pci->num_lanes as 0 and
dw_pcie_link_set_max_link_width() skips programming PORT_LINK_CTRL,
LINK_WIDTH_SPEED_CTRL, and PCI_EXP_LNKCAP_MLW.
> +
> + pcie1_ep: pcie-ep@1b88000 {
> + compatible = "qcom,nord-pcie-ep";
> +
> + reg = <0x00 0x01b88000 0x00 0x00004000>,
> + <0x00 0x50000000 0x00 0x00000f20>,
> + <0x00 0x50000f20 0x00 0x000000a8>,
> + <0x00 0x50010000 0x00 0x00010000>,
> + <0x00 0x50100000 0x00 0x00100000>,
[Severity: Medium]
Should the addr_space size in pcie1_ep, pcie2_ep, and pcie3_ep be
0x0ff00000 (255 MB, matching pcie0_ep and the full outbound slave window in
nord.dtsi) instead of 0x00100000 (1 MB)?
dw_pcie_ep_init() passes the addr_space size to pci_epc_mem_init() as the
total outbound address pool, so a 1 MB size limits outbound iATU mappings on
pcie1_ep..pcie3_ep to 1020 KB after reserving ep->msi_mem.
> + <0x00 0x01b8c000 0x00 0x00001000>,
> + <0x00 0x50030000 0x00 0x00010000>;
> + reg-names = "parf",
> + "dbi",
> + "elbi",
> + "atu",
> + "addr_space",
> + "mmio",
> + "dma";
[Severity: High]
Does omitting the "msix" reg entry on pcie1_ep, pcie2_ep, and pcie3_ep
cause pci_epf_mhi_epc_init() to fail with -EINVAL on those instances?
In drivers/pci/controller/dwc/pcie-qcom-ep.c, "qcom,nord-pcie-ep" maps to
cfg_nord with .msix_capable = true, and qcom_pcie_epc_get_features()
unconditionally reports msix_capable = true without checking whether an
"msix" resource exists. When pci_epf_mhi is bound to pcie1_ep..pcie3_ep,
epf_mhi->msix_phys is 0 and pci_epf_mhi_epc_init() fails on PERST#
deassertion:
drivers/pci/endpoint/functions/pci-epf-mhi.c:pci_epf_mhi_epc_init() {
...
if (epf_mhi->epc_features->msix_capable) {
if (!epf_mhi->msix_phys) {
dev_err(dev, "MSI-X BAR address not configured in DT\n");
return -EINVAL;
}
...
}
--
Sashiko AI review · https://sashiko.dev/#/patchset/20261122-nord_ep-v1-0-6d8839ffa9aa@oss.qualcomm.com?part=11
--
linux-phy mailing list
linux-phy@lists.infradead.org
https://lists.infradead.org/mailman/listinfo/linux-phy
prev parent reply other threads:[~2026-11-22 3:17 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-11-22 2:56 [PATCH 00/11] PCI: qcom-ep: Add Nord PCIe Endpoint controller support Krishna Chaitanya Chundru
2026-11-22 2:56 ` [PATCH 01/11] PCI: epf-mhi: Pass the actual number of MSI vectors to pci_epc_set_msi() Krishna Chaitanya Chundru
2026-11-22 3:03 ` sashiko-bot
2026-11-22 2:56 ` [PATCH 02/11] PCI: qcom-ep: Add MSI-X support Krishna Chaitanya Chundru
2026-11-22 3:08 ` sashiko-bot
2026-11-22 2:56 ` [PATCH 03/11] PCI: epf-mhi: " Krishna Chaitanya Chundru
2026-11-22 3:15 ` sashiko-bot
2026-11-22 2:56 ` [PATCH 04/11] PCI: dwc: Preserve glue-provided eDMA HDMA channel separation Krishna Chaitanya Chundru
2026-11-22 2:56 ` [PATCH 05/11] phy: qcom: qmp-pcie: Add PCIe endpoint mode support Krishna Chaitanya Chundru
2026-11-22 2:56 ` [PATCH 06/11] phy: qcom: qmp-pcie: Add Nord endpoint mode init sequences Krishna Chaitanya Chundru
2026-11-22 2:56 ` [PATCH 07/11] dt-bindings: PCI: qcom-ep: Add Nord PCIe Endpoint Krishna Chaitanya Chundru
2026-11-22 2:56 ` [PATCH 08/11] PCI: qcom-ep: Add Nord PCIe Endpoint controller support Krishna Chaitanya Chundru
2026-11-22 3:08 ` sashiko-bot
2026-11-22 2:56 ` [PATCH 09/11] PCI: epf-mhi: Add Nord endpoint support Krishna Chaitanya Chundru
2026-11-22 2:56 ` [PATCH 10/11] bus: mhi: host: pci_generic: Add support for Qualcomm Nord Krishna Chaitanya Chundru
2026-11-22 3:19 ` sashiko-bot
2026-11-22 2:56 ` [PATCH 11/11] arm64: dts: qcom: nord: Add PCIe endpoint nodes Krishna Chaitanya Chundru
2026-11-22 3:17 ` sashiko-bot [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=sashiko-outbox-227667@kernel.org \
--to=sashiko-bot@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krishna.chundru@oss.qualcomm.com \
--cc=linux-pci@vger.kernel.org \
--cc=linux-phy@lists.infradead.org \
--cc=neil.armstrong@linaro.org \
--cc=olteanv@gmail.com \
--cc=robh@kernel.org \
--cc=sashiko-reviews@lists.linux.dev \
--cc=vkoul@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox