From: Rajendra Nayak <rnayak@codeaurora.org>
To: linux-arm-msm@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, linux-pm@vger.kernel.org,
rui.zhang@intel.com, edubezval@gmail.com
Cc: sboyd@codeaurora.org, srinivas.kandagatla@linaro.org,
nrajan@codeaurora.org, lina.iyer@linaro.org,
Rajendra Nayak <rnayak@codeaurora.org>
Subject: [PATCH v2 9/9] arm64: dts: msm8916: Add thermal zones, tsens and qfprom nodes
Date: Wed, 16 Sep 2015 11:53:23 +0530 [thread overview]
Message-ID: <1442384603-26053-10-git-send-email-rnayak@codeaurora.org> (raw)
In-Reply-To: <1442384603-26053-1-git-send-email-rnayak@codeaurora.org>
Add thermal zones, tsens and qfprom nodes
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
---
arch/arm64/boot/dts/qcom/msm8916.dtsi | 66 +++++++++++++++++++++++++++++++++++
1 file changed, 66 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8916.dtsi b/arch/arm64/boot/dts/qcom/msm8916.dtsi
index 3e7083c..63b5262 100644
--- a/arch/arm64/boot/dts/qcom/msm8916.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8916.dtsi
@@ -68,6 +68,49 @@
};
};
+ thermal-zones {
+ cpu-thermal0 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 4>;
+
+ trips {
+ cpu_alert0: trip@0 {
+ temperature = <100000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit0: trip@1 {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ cpu-thermal1 {
+ polling-delay-passive = <250>;
+ polling-delay = <1000>;
+
+ thermal-sensors = <&tsens 3>;
+
+ trips {
+ cpu_alert1: trip@0 {
+ temperature = <100000>;
+ hysteresis = <2000>;
+ type = "passive";
+ };
+ cpu_crit1: trip@1 {
+ temperature = <125000>;
+ hysteresis = <2000>;
+ type = "critical";
+ };
+ };
+ };
+
+ };
+
timer {
compatible = "arm,armv8-timer";
interrupts = <GIC_PPI 2 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
@@ -392,6 +435,29 @@
interrupt-controller;
#interrupt-cells = <4>;
};
+
+ qfprom: qfprom@5c000 {
+ compatible = "qcom,qfprom";
+ reg = <0x5c000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ tsens_caldata: caldata@d0 {
+ reg = <0xd0 0x8>;
+ };
+ tsens_calsel: calsel@ec {
+ reg = <0xec 0x4>;
+ };
+ };
+
+ tsens: thermal-sensor@4a8000 {
+ compatible = "qcom,msm8916-tsens";
+ reg = <0x4a8000 0x2000>;
+ nvmem-cells = <&tsens_caldata>, <&tsens_calsel>;
+ nvmem-cell-names = "calib", "calib_sel";
+ qcom,tsens-slopes = <3200 3200 3200 3200 3200>;
+ qcom,sensor-id = <0 1 2 4 5>;
+ #thermal-sensor-cells = <1>;
+ };
};
};
--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation
prev parent reply other threads:[~2015-09-16 6:25 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-16 6:23 [PATCH v2 0/9] qcom: Add support for TSENS driver Rajendra Nayak
2015-09-16 6:23 ` [PATCH v2 1/9] thermal: qcom: tsens: Add a skeletal TSENS drivers Rajendra Nayak
2015-09-16 13:44 ` Punit Agrawal
2015-09-21 4:26 ` Rajendra Nayak
2015-09-16 6:23 ` [PATCH v2 2/9] thermal: qcom: tsens-8916: Add support for 8916 family of SoCs Rajendra Nayak
2015-09-16 13:46 ` Punit Agrawal
2015-09-21 4:28 ` Rajendra Nayak
2015-10-08 5:05 ` Rajendra Nayak
2015-10-08 14:32 ` Punit Agrawal
2015-09-16 6:23 ` [PATCH v2 3/9] thermal: qcom: tsens-8974: Add support for 8974 " Rajendra Nayak
2015-09-16 6:23 ` [PATCH v2 4/9] clk: qcom: create virtual child device for TSENS Rajendra Nayak
2015-09-16 22:39 ` Stephen Boyd
2015-09-21 4:28 ` Rajendra Nayak
2015-09-16 6:23 ` [PATCH v2 5/9] thermal: qcom: tsens-8960: Add support for 8960 family of SoCs Rajendra Nayak
2015-09-16 6:23 ` [PATCH v2 6/9] arm: dts: msm8974: Add thermal zones, tsens and qfprom nodes Rajendra Nayak
2015-09-16 6:23 ` [PATCH v2 7/9] arm: dts: apq8064: " Rajendra Nayak
2015-09-16 6:23 ` [PATCH v2 8/9] arm: dts: apq8084: " Rajendra Nayak
2015-09-16 6:23 ` Rajendra Nayak [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1442384603-26053-10-git-send-email-rnayak@codeaurora.org \
--to=rnayak@codeaurora.org \
--cc=edubezval@gmail.com \
--cc=lina.iyer@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=nrajan@codeaurora.org \
--cc=rui.zhang@intel.com \
--cc=sboyd@codeaurora.org \
--cc=srinivas.kandagatla@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).