From: Andreas Dannenberg <dannenberg@ti.com>
To: Sebastian Reichel <sre@kernel.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>,
David Woodhouse <dwmw2@infradead.org>,
Laurentiu Palcu <laurentiu.palcu@intel.com>,
Krzysztof Kozlowski <k.kozlowski@samsung.com>,
Ramakrishna Pallala <ramakrishna.pallala@intel.com>,
linux-pm@vger.kernel.org, devicetree@vger.kernel.org
Subject: Re: [PATCH v5 01/11] dt: power: bq24257-charger: Cover additional devices
Date: Tue, 22 Sep 2015 16:58:24 -0500 [thread overview]
Message-ID: <20150922215823.GA30297@beast> (raw)
In-Reply-To: <20150922162448.GE4235@earth>
On Tue, Sep 22, 2015 at 06:24:48PM +0200, Sebastian Reichel wrote:
> Hi,
>
> On Fri, Sep 18, 2015 at 04:39:49PM -0500, Andreas Dannenberg wrote:
> > Extend the bq24257 charger's device tree documentation to cover the
> > bq24250 and bq24251 devices as well feature additions.
>
> The binding looks fine to except for:
>
> > +- stat-gpios: GPIO used for the devices STAT_IN pin. Alternatively the pin can
> > + also be defined through the standard interrupt definition properties (see
> > + optional properties section below). Only use one method.
>
> Why do you expose two ways for this?
Hi Sebastian. The original driver exposed this - it just didn't
document it in the DT binding doc. I'm not sure why this was introduced
in the first place (Laurentiu?). I know we can't change the API but
since it was never documented maybe we can remove it?
Regards,
--
Andreas Dannenberg
Texas Instruments Inc
>
> -- Sebastian
next prev parent reply other threads:[~2015-09-22 22:04 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-09-18 21:39 [PATCH v5 00/11] power: bq24257: Add support for bq24250/bq24251 Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 01/11] dt: power: bq24257-charger: Cover additional devices Andreas Dannenberg
2015-09-22 16:24 ` Sebastian Reichel
2015-09-22 21:58 ` Andreas Dannenberg [this message]
2015-09-23 0:34 ` Sebastian Reichel
2015-09-23 8:14 ` Laurentiu Palcu
2015-09-23 14:13 ` Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 02/11] power: bq24257: Add basic support for bq24250/bq24251 Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 03/11] power: bq24257: Add bit definition for temp sense enable Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 04/11] power: bq24257: Allow manual setting of input current limit Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 06/11] power: bq24257: Use managed power supply register Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 07/11] power: bq24257: Add over voltage protection setting support Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 08/11] power: bq24257: Add input DPM voltage threshold " Andreas Dannenberg
[not found] ` <1442612399-341-1-git-send-email-dannenberg-l0cyMroinI0@public.gmane.org>
2015-09-18 21:39 ` [PATCH v5 05/11] power: bq24257: Add SW-based approach for Power Good determination Andreas Dannenberg
2015-09-22 19:37 ` Sebastian Reichel
2015-09-23 19:34 ` Andreas Dannenberg
2015-09-23 20:02 ` Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 09/11] power: bq24257: Allow input current limit sysfs access Andreas Dannenberg
2015-09-22 19:16 ` Sebastian Reichel
2015-09-22 22:10 ` Andreas Dannenberg
2015-09-23 0:29 ` Sebastian Reichel
2015-09-23 14:11 ` Andreas Dannenberg
2015-09-23 15:02 ` Sebastian Reichel
2015-09-23 18:32 ` Andreas Dannenberg
2015-09-23 18:53 ` Sebastian Reichel
2015-09-23 19:47 ` Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 10/11] power: bq24257: Add various device-specific sysfs properties Andreas Dannenberg
2015-09-18 21:39 ` [PATCH v5 11/11] power: bq24257: Add platform data based initialization Andreas Dannenberg
2015-09-22 19:29 ` Sebastian Reichel
2015-09-22 19:31 ` [PATCH v5 00/11] power: bq24257: Add support for bq24250/bq24251 Sebastian Reichel
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20150922215823.GA30297@beast \
--to=dannenberg@ti.com \
--cc=dbaryshkov@gmail.com \
--cc=devicetree@vger.kernel.org \
--cc=dwmw2@infradead.org \
--cc=k.kozlowski@samsung.com \
--cc=laurentiu.palcu@intel.com \
--cc=linux-pm@vger.kernel.org \
--cc=ramakrishna.pallala@intel.com \
--cc=sre@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).