[PATCH v9 0/8] devicetree battery support and client bq27xxx_battery

[PATCH v9 0/8] devicetree battery support and client bq27xxx_battery

[Liam Breck]

Overview:
* new devicetree battery node specifies static battery data
* fuel gauge and charger nodes shall use monitored-battery=<&battery_node>
* new power_supply_get_battery_info() reads battery data from devicetree
* new struct power_supply_battery_info provides battery data to drivers
* drivers surface battery data in sysfs via related power_supply_prop_* fields
* bq27xxx driver calls the above and writes battery data to RAM/NVM for params
  essential to correct operation: energy-full-design-microwatt-hours,
  charge-full-design-microamp-hours, voltage-min-design-microvolt

Changes in v9:
  bq27xxx_battery:
*   fix set_cfgupdate()
*   support bq27500, 545, 421; defer others
*   bq27441, 621 use enum BQ27425 instead of BQ27421
*   drop print_dm_blocks() patch
*   minor polishing
  Documentation/devicetree/.../battery.txt:
*   describe rationale for enum power_supply_property names

Changes in v8:
  bq27xxx_battery:
*   wait on flag after set_cfgupdate & soft_reset
*   drop print_config(), report status in update_dm_block()
*   clarify error messages
*   cleanup from Andrew's feedback; minor polishing

Changes in v7:
  bq27xxx_battery:
*   support chips where terminate_voltage & design_* live in separate blocks
*   draft support for 421, 441, 621 chips
*   new patch to log chip memory fields
*   report bus I/O errors; return error code in bq27xxx_battery_i2c
*   verify checksum in read_dm_block()
*   use set_cfgupdate only if chip provides it, soft_reset on I/O error
*   block_data_control=0 only in write_dm_block()
*   note toxic code from TI bqtool in write_dm_block()
*   lots of functionally neutral polishing
  Documentation/devicetree/.../battery.txt:
*   mention power_supply_get_battery_info()

Changes in v6:
* Documentation/devictree/... fixes
* bq27xxx_battery: clarify names
* bq27xxx_battery: verify that selected registers are supported
* bq27xxx_battery: allocate NVM buffer on stack
* bq27xxx_battery_i2c: fix return code of bulk_read

Changes in v5:
* incorporate feedback into Documentation/devicetree/.../battery.txt
* use power_supply_prop_* names in devicetree and power_supply_battery_info
* default fields to -EINVAL in power_supply_battery_info
* power_supply_get_battery_info() always looks for "monitored-battery"
* power_supply_get_battery_info() emits a warning if !psy->of_node
* squash patches for power_supply_battery_info
* bq27xxx_battery: check power_supply_battery_info values
* bq27xxx_battery: note missing power_supply_prop_* features
* bq27xxx_battery: new patch for access methods

Changes in v4:
* add "fixed-battery" compatible field to be be more consistant with devicetree

Changes in v3:
* split i2c changes into respective patches
* add documentation for battery information for fuel gauge
* rebased documentation patches on change on the list
* abstracted the battery configuration for the state machine
  to an generic struct and platform data access function

Changes in v2:
* add documentation for uWh and uAh property units
* change devicetree entries to match new property units

Liam (4):
  devicetree: power: Add battery.txt
  devicetree: power: bq27xxx: Add monitored-battery documentation
  power: power_supply: Add power_supply_battery_info and API
  power: bq27xxx_battery: Add power_supply_battery_info support

Matt Ranostay (4):
  devicetree: property-units: Add uWh and uAh units
  power: bq27xxx_battery: Define access methods to write chip registers
  power: bq27xxx_battery: Move BQ27421 chip id to its own group
  power: bq27xxx_battery_i2c: Add I2C bulk read/write functions

 .../devicetree/bindings/power/supply/battery.txt   |  45 ++
 .../devicetree/bindings/power/supply/bq27xxx.txt   |  11 +-
 .../devicetree/bindings/property-units.txt         |   2 +
 drivers/power/supply/bq27xxx_battery.c             | 506 ++++++++++++++++++++-
 drivers/power/supply/bq27xxx_battery_i2c.c         |  88 +++-
 drivers/power/supply/power_supply_core.c           |  40 ++
 include/linux/power/bq27xxx_battery.h              |   6 +-
 include/linux/power_supply.h                       |  18 +
 8 files changed, 707 insertions(+), 9 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power/supply/battery.txt

-- 
2.9.3

[PATCH v9 1/8] devicetree: power: Add battery.txt

[Liam Breck]

From: Liam Breck <kernel-RYWXG+zxWwBdeoIcmNTgJF6hYfS7NtTn@public.gmane.org>

Documentation of static battery characteristics that can be defined
for batteries which cannot self-identify. This information is required
by fuel-gauge and charger chips for proper handling of the battery.

Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Signed-off-by: Matt Ranostay <matt-sk+viVC6FLCDq+mSdOJa79kegs52MxvZ@public.gmane.org>
Signed-off-by: Liam Breck <kernel-RYWXG+zxWwBdeoIcmNTgJF6hYfS7NtTn@public.gmane.org>
---
 .../devicetree/bindings/power/supply/battery.txt   | 45 ++++++++++++++++++++++
 1 file changed, 45 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/power/supply/battery.txt

diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt
new file mode 100644
index 0000000..0278617
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/battery.txt
@@ -0,0 +1,45 @@
+Battery Characteristics
+
+Required Properties:
+ - compatible: Must be "fixed-battery"
+
+Optional Properties:
+ - voltage-min-design-microvolt: drained battery voltage
+ - energy-full-design-microwatt-hours: battery design energy
+ - charge-full-design-microamp-hours: battery design capacity
+
+Because drivers surface properties in sysfs using names derived
+from enum power_supply_property, e.g.
+/sys/class/power_supply/<device>/charge_full_design, our
+battery properties must be named for the corresponding elements in
+enum power_supply_property, defined in include/linux/power_supply.h.
+
+Batteries must be referenced by chargers and/or fuel-gauges
+using a phandle. The phandle's property should be named
+"monitored-battery".
+
+Driver code should call power_supply_get_battery_info() to obtain
+battery properties via monitored-battery. For details see:
+  drivers/power/supply/power_supply_core.c
+  drivers/power/supply/bq27xxx_battery.c
+
+Example:
+
+	bat: battery {
+		compatible = "fixed-battery";
+		voltage-min-design-microvolt = <3200000>;
+		energy-full-design-microwatt-hours = <5290000>;
+		charge-full-design-microamp-hours = <1430000>;
+	};
+
+	charger: charger@11 {
+		....
+		monitored-battery = <&bat>;
+		...
+	};
+
+	fuel_gauge: fuel-gauge@22 {
+		....
+		monitored-battery = <&bat>;
+		...
+	};
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 2/8] devicetree: property-units: Add uWh and uAh units

[Liam Breck]

From: Matt Ranostay <matt@ranostay.consulting>

Add entries for microwatt-hours and microamp-hours.

Cc: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
Acked-by: Sebastian Reichel <sre@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/property-units.txt | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/property-units.txt b/Documentation/devicetree/bindings/property-units.txt
index 12278d7..0849618 100644
--- a/Documentation/devicetree/bindings/property-units.txt
+++ b/Documentation/devicetree/bindings/property-units.txt
@@ -25,8 +25,10 @@ Distance
 Electricity
 ----------------------------------------
 -microamp	: micro amps
+-microamp-hours : micro amp-hours
 -ohms		: Ohms
 -micro-ohms	: micro Ohms
+-microwatt-hours: micro Watt-hours
 -microvolt	: micro volts
 
 Temperature
-- 
2.9.3

[PATCH v9 3/8] devicetree: power: bq27xxx: Add monitored-battery documentation

[Liam Breck]

From: Liam Breck <kernel-RYWXG+zxWwBdeoIcmNTgJF6hYfS7NtTn@public.gmane.org>

Document monitored-battery = <&battery_node>

Cc: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
Cc: devicetree-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
Signed-off-by: Matt Ranostay <matt-sk+viVC6FLCDq+mSdOJa79kegs52MxvZ@public.gmane.org>
Signed-off-by: Liam Breck <kernel-RYWXG+zxWwBdeoIcmNTgJF6hYfS7NtTn@public.gmane.org>
Acked-by: Rob Herring <robh-DgEjT+Ai2ygdnm+yROfE0A@public.gmane.org>
---
 Documentation/devicetree/bindings/power/supply/bq27xxx.txt | 11 ++++++++++-
 1 file changed, 10 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt
index b0c95ef..cf83371 100644
--- a/Documentation/devicetree/bindings/power/supply/bq27xxx.txt
+++ b/Documentation/devicetree/bindings/power/supply/bq27xxx.txt
@@ -28,9 +28,18 @@ Required properties:
  * "ti,bq27621" - BQ27621
 - reg: integer, i2c address of the device.
 
+Optional properties:
+- monitored-battery: phandle of battery information devicetree node
+
+  See Documentation/devicetree/bindings/power/supply/battery.txt
+  If either of the referenced battery's *-full-design-*-hours properties are set,
+  then both must be.
+
 Example:
 
-bq27510g3 {
+bq27510g3 : fuel-gauge@55 {
     compatible = "ti,bq27510g3";
     reg = <0x55>;
+
+    monitored-battery = <&bat>;
 };
-- 
2.9.3

--
To unsubscribe from this list: send the line "unsubscribe devicetree" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH v9 4/8] power: power_supply: Add power_supply_battery_info and API

[Liam Breck]

From: Liam Breck <kernel@networkimprov.net>

power_supply_get_battery_info() reads battery data from devicetree.
struct power_supply_battery_info provides battery data to drivers.
Drivers may surface battery data in sysfs via corresponding
POWER_SUPPLY_PROP_* fields.

Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
---
 drivers/power/supply/power_supply_core.c | 40 ++++++++++++++++++++++++++++++++
 include/linux/power_supply.h             | 18 ++++++++++++++
 2 files changed, 58 insertions(+)

diff --git a/drivers/power/supply/power_supply_core.c b/drivers/power/supply/power_supply_core.c
index a74d8ca..c121931 100644
--- a/drivers/power/supply/power_supply_core.c
+++ b/drivers/power/supply/power_supply_core.c
@@ -17,6 +17,7 @@
 #include <linux/device.h>
 #include <linux/notifier.h>
 #include <linux/err.h>
+#include <linux/of.h>
 #include <linux/power_supply.h>
 #include <linux/thermal.h>
 #include "power_supply.h"
@@ -487,6 +488,45 @@ struct power_supply *devm_power_supply_get_by_phandle(struct device *dev,
 EXPORT_SYMBOL_GPL(devm_power_supply_get_by_phandle);
 #endif /* CONFIG_OF */
 
+int power_supply_get_battery_info(struct power_supply *psy,
+				  struct power_supply_battery_info *info)
+{
+	struct device_node *battery_np;
+	const char *value;
+	int err;
+
+	info->energy_full_design_uwh = -EINVAL;
+	info->charge_full_design_uah = -EINVAL;
+	info->voltage_min_design_uv  = -EINVAL;
+
+	if (!psy->of_node) {
+		dev_warn(&psy->dev, "%s currently only supports devicetree\n",
+			 __func__);
+		return -ENXIO;
+	}
+
+	battery_np = of_parse_phandle(psy->of_node, "monitored-battery", 0);
+	if (!battery_np)
+		return -ENODEV;
+
+	err = of_property_read_string(battery_np, "compatible", &value);
+	if (err)
+		return err;
+
+	if (strcmp("fixed-battery", value))
+		return -ENODEV;
+
+	of_property_read_u32(battery_np, "energy-full-design-microwatt-hours",
+			     &info->energy_full_design_uwh);
+	of_property_read_u32(battery_np, "charge-full-design-microamp-hours",
+			     &info->charge_full_design_uah);
+	of_property_read_u32(battery_np, "voltage-min-design-microvolt",
+			     &info->voltage_min_design_uv);
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(power_supply_get_battery_info);
+
 int power_supply_get_property(struct power_supply *psy,
 			    enum power_supply_property psp,
 			    union power_supply_propval *val)
diff --git a/include/linux/power_supply.h b/include/linux/power_supply.h
index 3965503..e84f1d3 100644
--- a/include/linux/power_supply.h
+++ b/include/linux/power_supply.h
@@ -288,6 +288,21 @@ struct power_supply_info {
 	int use_for_apm;
 };
 
+/*
+ * This is the recommended struct to manage static battery parameters,
+ * populated by power_supply_get_battery_info(). Most platform drivers should
+ * use these for consistency.
+ * Its field names must correspond to elements in enum power_supply_property.
+ * The default field value is -EINVAL.
+ * Power supply class itself doesn't use this.
+ */
+
+struct power_supply_battery_info {
+	int energy_full_design_uwh;	/* microWatt-hours */
+	int charge_full_design_uah;	/* microAmp-hours */
+	int voltage_min_design_uv;	/* microVolts */
+};
+
 extern struct atomic_notifier_head power_supply_notifier;
 extern int power_supply_reg_notifier(struct notifier_block *nb);
 extern void power_supply_unreg_notifier(struct notifier_block *nb);
@@ -306,6 +321,9 @@ static inline struct power_supply *
 devm_power_supply_get_by_phandle(struct device *dev, const char *property)
 { return NULL; }
 #endif /* CONFIG_OF */
+
+extern int power_supply_get_battery_info(struct power_supply *psy,
+					 struct power_supply_battery_info *info);
 extern void power_supply_changed(struct power_supply *psy);
 extern int power_supply_am_i_supplied(struct power_supply *psy);
 extern int power_supply_set_battery_charged(struct power_supply *psy);
-- 
2.9.3

[PATCH v9 5/8] power: bq27xxx_battery: Define access methods to write chip registers

[Liam Breck]

From: Matt Ranostay <matt@ranostay.consulting>

write(), read_bulk(), write_bulk() support setting chip registers,
e.g. with data obtained from power_supply_battery_info.

Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
---
 include/linux/power/bq27xxx_battery.h | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/include/linux/power/bq27xxx_battery.h b/include/linux/power/bq27xxx_battery.h
index bed9557..92df553 100644
--- a/include/linux/power/bq27xxx_battery.h
+++ b/include/linux/power/bq27xxx_battery.h
@@ -32,6 +32,9 @@ struct bq27xxx_platform_data {
 struct bq27xxx_device_info;
 struct bq27xxx_access_methods {
 	int (*read)(struct bq27xxx_device_info *di, u8 reg, bool single);
+	int (*write)(struct bq27xxx_device_info *di, u8 reg, int value, bool single);
+	int (*read_bulk)(struct bq27xxx_device_info *di, u8 reg, u8 *data, int len);
+	int (*write_bulk)(struct bq27xxx_device_info *di, u8 reg, u8 *data, int len);
 };
 
 struct bq27xxx_reg_cache {
-- 
2.9.3

[PATCH v9 6/8] power: bq27xxx_battery: Move BQ27421 chip id to its own group

[Liam Breck]

From: Matt Ranostay <matt@ranostay.consulting>

Add BQ27425 id to cover 425, 441, 621 chips.
This allows support for 421 by the devicetree code.

Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
---
 drivers/power/supply/bq27xxx_battery.c     | 23 ++++++++++++++++++++++-
 drivers/power/supply/bq27xxx_battery_i2c.c |  6 +++---
 include/linux/power/bq27xxx_battery.h      |  3 ++-
 3 files changed, 27 insertions(+), 5 deletions(-)

diff --git a/drivers/power/supply/bq27xxx_battery.c b/drivers/power/supply/bq27xxx_battery.c
index 7272d1e..7475a5f 100644
--- a/drivers/power/supply/bq27xxx_battery.c
+++ b/drivers/power/supply/bq27xxx_battery.c
@@ -259,6 +259,25 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_DCAP] = 0x3c,
 		[BQ27XXX_REG_AP] = 0x18,
 	},
+	[BQ27425] = {
+		[BQ27XXX_REG_CTRL] = 0x00,
+		[BQ27XXX_REG_TEMP] = 0x02,
+		[BQ27XXX_REG_INT_TEMP] = 0x1e,
+		[BQ27XXX_REG_VOLT] = 0x04,
+		[BQ27XXX_REG_AI] = 0x10,
+		[BQ27XXX_REG_FLAGS] = 0x06,
+		[BQ27XXX_REG_TTE] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_TTF] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_TTES] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_TTECP] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_NAC] = 0x08,
+		[BQ27XXX_REG_FCC] = 0x0e,
+		[BQ27XXX_REG_CYCT] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_AE] = INVALID_REG_ADDR,
+		[BQ27XXX_REG_SOC] = 0x1c,
+		[BQ27XXX_REG_DCAP] = 0x3c,
+		[BQ27XXX_REG_AP] = 0x18,
+	},
 };
 
 static enum power_supply_property bq27000_battery_props[] = {
@@ -427,6 +446,7 @@ static struct {
 	BQ27XXX_PROP(BQ27541, bq27541_battery_props),
 	BQ27XXX_PROP(BQ27545, bq27545_battery_props),
 	BQ27XXX_PROP(BQ27421, bq27421_battery_props),
+	BQ27XXX_PROP(BQ27425, bq27421_battery_props),
 };
 
 static DEFINE_MUTEX(bq27xxx_list_lock);
@@ -682,6 +702,7 @@ static bool bq27xxx_battery_overtemp(struct bq27xxx_device_info *di, u16 flags)
 		return flags & (BQ27XXX_FLAG_OTC | BQ27XXX_FLAG_OTD);
 	case BQ27530:
 	case BQ27421:
+	case BQ27425:
 		return flags & BQ27XXX_FLAG_OT;
 	default:
 		return false;
@@ -693,7 +714,7 @@ static bool bq27xxx_battery_overtemp(struct bq27xxx_device_info *di, u16 flags)
  */
 static bool bq27xxx_battery_undertemp(struct bq27xxx_device_info *di, u16 flags)
 {
-	if (di->chip == BQ27530 || di->chip == BQ27421)
+	if (di->chip == BQ27530 || di->chip == BQ27421 || di->chip == BQ27425)
 		return flags & BQ27XXX_FLAG_UT;
 
 	return false;
diff --git a/drivers/power/supply/bq27xxx_battery_i2c.c b/drivers/power/supply/bq27xxx_battery_i2c.c
index 5c5c3a6..7781ca9 100644
--- a/drivers/power/supply/bq27xxx_battery_i2c.c
+++ b/drivers/power/supply/bq27xxx_battery_i2c.c
@@ -159,9 +159,9 @@ static const struct i2c_device_id bq27xxx_i2c_id_table[] = {
 	{ "bq27742", BQ27541 },
 	{ "bq27545", BQ27545 },
 	{ "bq27421", BQ27421 },
-	{ "bq27425", BQ27421 },
-	{ "bq27441", BQ27421 },
-	{ "bq27621", BQ27421 },
+	{ "bq27425", BQ27425 },
+	{ "bq27441", BQ27425 },
+	{ "bq27621", BQ27425 },
 	{},
 };
 MODULE_DEVICE_TABLE(i2c, bq27xxx_i2c_id_table);
diff --git a/include/linux/power/bq27xxx_battery.h b/include/linux/power/bq27xxx_battery.h
index 92df553..44f469a 100644
--- a/include/linux/power/bq27xxx_battery.h
+++ b/include/linux/power/bq27xxx_battery.h
@@ -9,7 +9,8 @@ enum bq27xxx_chip {
 	BQ27530, /* bq27530, bq27531 */
 	BQ27541, /* bq27541, bq27542, bq27546, bq27742 */
 	BQ27545, /* bq27545 */
-	BQ27421, /* bq27421, bq27425, bq27441, bq27621 */
+	BQ27421, /* bq27421 */
+	BQ27425, /* bq27425, bq27441, bq27621 */
 };
 
 /**
-- 
2.9.3

[PATCH v9 7/8] power: bq27xxx_battery: Add power_supply_battery_info support

[Liam Breck]

From: Liam Breck <kernel@networkimprov.net>

Previously there was no way to configure chip registers in the event that the
defaults didn't match the battery in question.

BQ27xxx driver now calls power_supply_get_battery_info, checks the inputs,
and writes battery data to chip RAM or non-volatile memory.

Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
---
 drivers/power/supply/bq27xxx_battery.c | 483 ++++++++++++++++++++++++++++++++-
 1 file changed, 481 insertions(+), 2 deletions(-)

diff --git a/drivers/power/supply/bq27xxx_battery.c b/drivers/power/supply/bq27xxx_battery.c
index 7475a5f..ed976a1 100644
--- a/drivers/power/supply/bq27xxx_battery.c
+++ b/drivers/power/supply/bq27xxx_battery.c
@@ -51,7 +51,7 @@
 
 #include <linux/power/bq27xxx_battery.h>
 
-#define DRIVER_VERSION		"1.2.0"
+#define DRIVER_VERSION		"1.3.0"
 
 #define BQ27XXX_MANUFACTURER	"Texas Instruments"
 
@@ -59,6 +59,7 @@
 #define BQ27XXX_FLAG_DSC	BIT(0)
 #define BQ27XXX_FLAG_SOCF	BIT(1) /* State-of-Charge threshold final */
 #define BQ27XXX_FLAG_SOC1	BIT(2) /* State-of-Charge threshold 1 */
+#define BQ27XXX_FLAG_CFGUP	BIT(4)
 #define BQ27XXX_FLAG_FC		BIT(9)
 #define BQ27XXX_FLAG_OTD	BIT(14)
 #define BQ27XXX_FLAG_OTC	BIT(15)
@@ -72,6 +73,11 @@
 #define BQ27000_FLAG_FC		BIT(5)
 #define BQ27000_FLAG_CHGS	BIT(7) /* Charge state flag */
 
+/* control register params */
+#define BQ27XXX_SEALED			0x20
+#define BQ27XXX_SET_CFGUPDATE		0x13
+#define BQ27XXX_SOFT_RESET		0x42
+
 #define BQ27XXX_RS			(20) /* Resistor sense mOhm */
 #define BQ27XXX_POWER_CONSTANT		(29200) /* 29.2 µV^2 * 1000 */
 #define BQ27XXX_CURRENT_CONSTANT	(3570) /* 3.57 µV * 1000 */
@@ -102,6 +108,11 @@ enum bq27xxx_reg_index {
 	BQ27XXX_REG_SOC,	/* State-of-Charge */
 	BQ27XXX_REG_DCAP,	/* Design Capacity */
 	BQ27XXX_REG_AP,		/* Average Power */
+	BQ27XXX_DM_CTRL,	/* BlockDataControl() */
+	BQ27XXX_DM_CLASS,	/* DataClass() */
+	BQ27XXX_DM_BLOCK,	/* DataBlock() */
+	BQ27XXX_DM_DATA,	/* BlockData() */
+	BQ27XXX_DM_CKSUM,	/* BlockDataChecksum() */
 	BQ27XXX_REG_MAX,	/* sentinel */
 };
 
@@ -125,6 +136,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x0b,
 		[BQ27XXX_REG_DCAP] = 0x76,
 		[BQ27XXX_REG_AP] = 0x24,
+		[BQ27XXX_DM_CTRL] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_CLASS] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_BLOCK] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_DATA] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_CKSUM] = INVALID_REG_ADDR,
 	},
 	[BQ27010] = {
 		[BQ27XXX_REG_CTRL] = 0x00,
@@ -144,6 +160,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x0b,
 		[BQ27XXX_REG_DCAP] = 0x76,
 		[BQ27XXX_REG_AP] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_CTRL] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_CLASS] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_BLOCK] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_DATA] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_CKSUM] = INVALID_REG_ADDR,
 	},
 	[BQ27500] = {
 		[BQ27XXX_REG_CTRL] = 0x00,
@@ -163,6 +184,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x2c,
 		[BQ27XXX_REG_DCAP] = 0x3c,
 		[BQ27XXX_REG_AP] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_CTRL] = 0x61,
+		[BQ27XXX_DM_CLASS] = 0x3e,
+		[BQ27XXX_DM_BLOCK] = 0x3f,
+		[BQ27XXX_DM_DATA] = 0x40,
+		[BQ27XXX_DM_CKSUM] = 0x60,
 	},
 	[BQ27510] = {
 		[BQ27XXX_REG_CTRL] = 0x00,
@@ -182,6 +208,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x20,
 		[BQ27XXX_REG_DCAP] = 0x2e,
 		[BQ27XXX_REG_AP] = INVALID_REG_ADDR,
+		[BQ27XXX_DM_CTRL] = 0x61,
+		[BQ27XXX_DM_CLASS] = 0x3e,
+		[BQ27XXX_DM_BLOCK] = 0x3f,
+		[BQ27XXX_DM_DATA] = 0x40,
+		[BQ27XXX_DM_CKSUM] = 0x60,
 	},
 	[BQ27530] = {
 		[BQ27XXX_REG_CTRL] = 0x00,
@@ -201,6 +232,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x2c,
 		[BQ27XXX_REG_DCAP] = INVALID_REG_ADDR,
 		[BQ27XXX_REG_AP] = 0x24,
+		[BQ27XXX_DM_CTRL] = 0x61,
+		[BQ27XXX_DM_CLASS] = 0x3e,
+		[BQ27XXX_DM_BLOCK] = 0x3f,
+		[BQ27XXX_DM_DATA] = 0x40,
+		[BQ27XXX_DM_CKSUM] = 0x60,
 	},
 	[BQ27541] = {
 		[BQ27XXX_REG_CTRL] = 0x00,
@@ -220,6 +256,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x2c,
 		[BQ27XXX_REG_DCAP] = 0x3c,
 		[BQ27XXX_REG_AP] = 0x24,
+		[BQ27XXX_DM_CTRL] = 0x61,
+		[BQ27XXX_DM_CLASS] = 0x3e,
+		[BQ27XXX_DM_BLOCK] = 0x3f,
+		[BQ27XXX_DM_DATA] = 0x40,
+		[BQ27XXX_DM_CKSUM] = 0x60,
 	},
 	[BQ27545] = {
 		[BQ27XXX_REG_CTRL] = 0x00,
@@ -239,6 +280,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x2c,
 		[BQ27XXX_REG_DCAP] = INVALID_REG_ADDR,
 		[BQ27XXX_REG_AP] = 0x24,
+		[BQ27XXX_DM_CTRL] = 0x61,
+		[BQ27XXX_DM_CLASS] = 0x3e,
+		[BQ27XXX_DM_BLOCK] = 0x3f,
+		[BQ27XXX_DM_DATA] = 0x40,
+		[BQ27XXX_DM_CKSUM] = 0x60,
 	},
 	[BQ27421] = {
 		[BQ27XXX_REG_CTRL] = 0x00,
@@ -258,6 +304,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x1c,
 		[BQ27XXX_REG_DCAP] = 0x3c,
 		[BQ27XXX_REG_AP] = 0x18,
+		[BQ27XXX_DM_CTRL] = 0x61,
+		[BQ27XXX_DM_CLASS] = 0x3e,
+		[BQ27XXX_DM_BLOCK] = 0x3f,
+		[BQ27XXX_DM_DATA] = 0x40,
+		[BQ27XXX_DM_CKSUM] = 0x60,
 	},
 	[BQ27425] = {
 		[BQ27XXX_REG_CTRL] = 0x00,
@@ -277,6 +328,11 @@ static u8 bq27xxx_regs[][BQ27XXX_REG_MAX] = {
 		[BQ27XXX_REG_SOC] = 0x1c,
 		[BQ27XXX_REG_DCAP] = 0x3c,
 		[BQ27XXX_REG_AP] = 0x18,
+		[BQ27XXX_DM_CTRL] = 0x61,
+		[BQ27XXX_DM_CLASS] = 0x3e,
+		[BQ27XXX_DM_BLOCK] = 0x3f,
+		[BQ27XXX_DM_DATA] = 0x40,
+		[BQ27XXX_DM_CKSUM] = 0x60,
 	},
 };
 
@@ -452,6 +508,106 @@ static struct {
 static DEFINE_MUTEX(bq27xxx_list_lock);
 static LIST_HEAD(bq27xxx_battery_devices);
 
+#define BQ27XXX_DM_SZ	32
+
+#define BQ27XXX_MSLEEP(i) usleep_range((i)*1000, (i)*1000+500)
+
+struct bq27xxx_dm_reg {
+	u8 subclass_id;
+	u8 offset;
+	u8 bytes;
+	u16 min, max;
+};
+
+struct bq27xxx_dm_buf {
+	u8 class;
+	u8 block;
+	u8 a[BQ27XXX_DM_SZ];
+	bool full, updt;
+};
+
+#define BQ27XXX_DM_BUF(di, i) { \
+	.class = bq27xxx_dm_regs[(di)->chip][i].subclass_id, \
+	.block = bq27xxx_dm_regs[(di)->chip][i].offset / BQ27XXX_DM_SZ, \
+}
+
+static inline u16* bq27xxx_dm_reg_ptr(struct bq27xxx_dm_buf *buf,
+				      struct bq27xxx_dm_reg *reg)
+{
+	if (buf->class == reg->subclass_id
+	 && buf->block == reg->offset / BQ27XXX_DM_SZ)
+		return (u16*) (buf->a + reg->offset % BQ27XXX_DM_SZ);
+
+	return NULL;
+}
+
+enum bq27xxx_dm_reg_id {
+	BQ27XXX_DM_DESIGN_CAPACITY = 0,
+	BQ27XXX_DM_DESIGN_ENERGY,
+	BQ27XXX_DM_TERMINATE_VOLTAGE,
+};
+
+static const char* bq27xxx_dm_reg_name[] = {
+	[BQ27XXX_DM_DESIGN_CAPACITY] = "design-capacity",
+	[BQ27XXX_DM_DESIGN_ENERGY] = "design-energy",
+	[BQ27XXX_DM_TERMINATE_VOLTAGE] = "terminate-voltage",
+};
+
+static struct bq27xxx_dm_reg bq27500_dm_regs[] = {
+	[BQ27XXX_DM_DESIGN_CAPACITY]   = { 48, 10, 2,    0, 65535 },
+	[BQ27XXX_DM_DESIGN_ENERGY]     = { }, /* missing on chip */
+	[BQ27XXX_DM_TERMINATE_VOLTAGE] = { 80, 48, 2, 1000, 32767 },
+};
+
+static struct bq27xxx_dm_reg bq27545_dm_regs[] = {
+	[BQ27XXX_DM_DESIGN_CAPACITY]   = { 48, 23, 2,    0, 32767 },
+	[BQ27XXX_DM_DESIGN_ENERGY]     = { 48, 25, 2,    0, 32767 },
+	[BQ27XXX_DM_TERMINATE_VOLTAGE] = { 80, 67, 2, 2800,  3700 },
+};
+
+static struct bq27xxx_dm_reg bq27421_dm_regs[] = {
+	[BQ27XXX_DM_DESIGN_CAPACITY]   = { 82, 10, 2,    0,  8000 },
+	[BQ27XXX_DM_DESIGN_ENERGY]     = { 82, 12, 2,    0, 32767 },
+	[BQ27XXX_DM_TERMINATE_VOLTAGE] = { 82, 16, 2, 2500,  3700 },
+};
+
+/* requires di->chip/group distinction
+ *static struct bq27xxx_dm_reg bq27425_dm_regs[] = {
+ *	[BQ27XXX_DM_DESIGN_CAPACITY]   = { 82, 12, 2,    0, 32767 },
+ *	[BQ27XXX_DM_DESIGN_ENERGY]     = { 82, 14, 2,    0, 32767 },
+ *	[BQ27XXX_DM_TERMINATE_VOLTAGE] = { 82, 18, 2, 2800,  3700 },
+ *};
+ *
+ *static struct bq27xxx_dm_reg bq27621_dm_regs[] = {
+ *	[BQ27XXX_DM_DESIGN_CAPACITY]   = { 82, 3, 2,    0,  8000 },
+ *	[BQ27XXX_DM_DESIGN_ENERGY]     = { 82, 5, 2,    0, 32767 },
+ *	[BQ27XXX_DM_TERMINATE_VOLTAGE] = { 82, 9, 2, 2500,  3700 },
+ *};
+ */
+
+static struct bq27xxx_dm_reg *bq27xxx_dm_regs[] = {
+	[BQ27500] = bq27500_dm_regs,
+	[BQ27545] = bq27545_dm_regs,
+	[BQ27421] = bq27421_dm_regs,
+/* requires di->chip/group distinction
+ *	[BQ27425] = bq27425_dm_regs,
+ *	[BQ27441] = bq27421_dm_regs,
+ *	[BQ27621] = bq27621_dm_regs,
+ */
+};
+
+static u32 bq27xxx_unseal_keys[] = {
+	[BQ27500] = 0x04143672,
+	[BQ27545] = 0x04143672,
+	[BQ27421] = 0x80008000,
+/* requires di->chip/group distinction
+ *	[BQ27425] = 0x04143672,
+ *	[BQ27441] = 0x80008000,
+ *	[BQ27621] = 0x80008000,
+ */
+};
+
+
 static int poll_interval_param_set(const char *val, const struct kernel_param *kp)
 {
 	struct bq27xxx_device_info *di;
@@ -496,6 +652,318 @@ static inline int bq27xxx_read(struct bq27xxx_device_info *di, int reg_index,
 	return di->bus.read(di, di->regs[reg_index], single);
 }
 
+static int bq27xxx_battery_set_seal_state(struct bq27xxx_device_info *di,
+					  bool state)
+{
+	int ret;
+
+	if (state) {
+		ret = di->bus.write(di, di->regs[BQ27XXX_REG_CTRL], BQ27XXX_SEALED, false);
+		if (ret < 0)
+			goto out;
+	} else {
+		u32 key = bq27xxx_unseal_keys[di->chip];
+
+		ret = di->bus.write(di, di->regs[BQ27XXX_REG_CTRL], (u16)(key >> 16), false);
+		if (ret < 0)
+			goto out;
+
+		ret = di->bus.write(di, di->regs[BQ27XXX_REG_CTRL], (u16)key, false);
+		if (ret < 0)
+			goto out;
+	}
+	return 0;
+
+out:
+	dev_err(di->dev, "bus error on %s: %d\n", state ? "seal" : "unseal", ret);
+	return ret;
+}
+
+static u8 bq27xxx_battery_checksum_dm_block(struct bq27xxx_dm_buf *buf)
+{
+	u16 sum = 0;
+	int i;
+
+	for (i = 0; i < BQ27XXX_DM_SZ; i++)
+		sum += buf->a[i];
+	sum &= 0xff;
+
+	return 0xff - sum;
+}
+
+static int bq27xxx_battery_read_dm_block(struct bq27xxx_device_info *di,
+					 struct bq27xxx_dm_buf *buf)
+{
+	int ret;
+
+	ret = di->bus.write(di, di->regs[BQ27XXX_DM_CLASS], buf->class, true);
+	if (ret < 0)
+		goto out;
+
+	ret = di->bus.write(di, di->regs[BQ27XXX_DM_BLOCK], buf->block, true);
+	if (ret < 0)
+		goto out;
+
+	BQ27XXX_MSLEEP(1);
+
+	ret = di->bus.read_bulk(di, di->regs[BQ27XXX_DM_DATA], buf->a, BQ27XXX_DM_SZ);
+	if (ret < 0)
+		goto out;
+
+	ret = di->bus.read(di, di->regs[BQ27XXX_DM_CKSUM], true);
+	if (ret < 0)
+		goto out;
+
+	if ((u8)ret != bq27xxx_battery_checksum_dm_block(buf)) {
+		ret = -EINVAL;
+		goto out;
+	}
+
+	buf->full = true;
+	buf->updt = false;
+	return 0;
+
+out:
+	dev_err(di->dev, "bus error reading chip memory: %d\n", ret);
+	return ret;
+}
+
+static void bq27xxx_battery_update_dm_block(struct bq27xxx_device_info *di,
+					    struct bq27xxx_dm_buf *buf,
+					    enum bq27xxx_dm_reg_id reg_id,
+					    unsigned int val)
+{
+	struct bq27xxx_dm_reg *reg = &bq27xxx_dm_regs[di->chip][reg_id];
+	const char* str = bq27xxx_dm_reg_name[reg_id];
+	u16 *prev = bq27xxx_dm_reg_ptr(buf, reg);
+
+	if (prev == NULL) {
+		dev_warn(di->dev, "buffer does not match %s dm spec\n", str);
+		return;
+	}
+
+	if (reg->bytes != 2) {
+		dev_warn(di->dev, "%s dm spec has unsupported byte size\n", str);
+		return;
+	}
+
+	if (!buf->full)
+		return;
+
+	if (be16_to_cpup(prev) == val) {
+		dev_info(di->dev, "%s has %u\n", str, val);
+		return;
+	}
+
+	dev_info(di->dev, "update %s to %u\n", str, val);
+
+	*prev = cpu_to_be16(val);
+	buf->updt = true;
+}
+
+static int bq27xxx_battery_set_cfgupdate(struct bq27xxx_device_info *di,
+					 bool state)
+{
+	int ret, try=100;
+
+	ret = di->bus.write(di, di->regs[BQ27XXX_REG_CTRL],
+			    state ? BQ27XXX_SET_CFGUPDATE : BQ27XXX_SOFT_RESET,
+			    false);
+	if (ret < 0)
+		goto out;
+
+	do {
+		BQ27XXX_MSLEEP(25);
+		ret = di->bus.read(di, di->regs[BQ27XXX_REG_FLAGS], false);
+		if (ret < 0)
+			goto out;
+	} while (!(ret & BQ27XXX_FLAG_CFGUP) == state && --try);
+
+	if (100-try) /* remove after other cfgupdate parts are tested */
+		dev_info(di->dev, "cfgupdate %d, retries %d\n", state, 100-try);
+
+	if (try)
+		return 0;
+
+	dev_err(di->dev, "timed out waiting for cfgupdate flag %d\n", state);
+	return -EINVAL;
+
+out:
+	dev_err(di->dev, "bus error on %s: %d\n", state ? "set_cfgupdate" : "soft_reset", ret);
+	return ret;
+}
+
+static int bq27xxx_battery_write_dm_block(struct bq27xxx_device_info *di,
+					  struct bq27xxx_dm_buf *buf)
+{
+	bool cfgup = di->chip == BQ27425 || di->chip == BQ27421; /* || BQ27441 || BQ27621 */
+	int ret;
+
+	if (!buf->updt)
+		return 0;
+
+	if (cfgup) {
+		ret = bq27xxx_battery_set_cfgupdate(di, true);
+		if (ret < 0)
+			return ret;
+	}
+
+	ret = di->bus.write(di, di->regs[BQ27XXX_DM_CTRL], 0, true);
+	if (ret < 0)
+		goto out;
+
+	ret = di->bus.write(di, di->regs[BQ27XXX_DM_CLASS], buf->class, true);
+	if (ret < 0)
+		goto out;
+
+	ret = di->bus.write(di, di->regs[BQ27XXX_DM_BLOCK], buf->block, true);
+	if (ret < 0)
+		goto out;
+
+	BQ27XXX_MSLEEP(1);
+
+	ret = di->bus.write_bulk(di, di->regs[BQ27XXX_DM_DATA], buf->a, BQ27XXX_DM_SZ);
+	if (ret < 0)
+		goto out;
+
+	ret = di->bus.write(di, di->regs[BQ27XXX_DM_CKSUM],
+			    bq27xxx_battery_checksum_dm_block(buf), true);
+	if (ret < 0)
+		goto out;
+
+	/* THE FOLLOWING SEQUENCE IS TOXIC. DO NOT USE!
+	 * If the 'time' delay is insufficient, NVM corruption results on
+	 * the '425 chip (and perhaps others), which could damage the chip.
+	 * It was suggested in this TI tool:
+	 *   http://git.ti.com/bms-linux/bqtool/blobs/master/gauge.c#line328
+	 *
+	 * 1. MSLEEP(time) after above write(BQ27XXX_DM_CKSUM, ...)
+	 * 2. write(BQ27XXX_DM_BLOCK, buf->block)
+	 * 3. sum = read(BQ27XXX_DM_CKSUM)
+	 * 4. if (sum != bq27xxx_battery_checksum_dm_block(buf))
+	 *      report error
+	 */
+
+	if (cfgup) {
+		BQ27XXX_MSLEEP(1);
+		ret = bq27xxx_battery_set_cfgupdate(di, false);
+		if (ret < 0)
+			return ret;
+	} else {
+		/* flash DM updates in <100ms, but reset time isn't documented */
+		BQ27XXX_MSLEEP(400);
+	}
+
+	buf->updt = false;
+	return 0;
+
+out:
+	if (cfgup)
+		bq27xxx_battery_set_cfgupdate(di, false);
+
+	dev_err(di->dev, "bus error writing chip memory: %d\n", ret);
+	return ret;
+}
+
+static void bq27xxx_battery_set_config(struct bq27xxx_device_info *di,
+				       struct power_supply_battery_info *info)
+{
+	struct bq27xxx_dm_buf bd = BQ27XXX_DM_BUF(di, BQ27XXX_DM_DESIGN_CAPACITY);
+	struct bq27xxx_dm_buf bt = BQ27XXX_DM_BUF(di, BQ27XXX_DM_TERMINATE_VOLTAGE);
+
+	if (info->charge_full_design_uah != -EINVAL
+	 && info->energy_full_design_uwh != -EINVAL) {
+		bq27xxx_battery_read_dm_block(di, &bd);
+		/* assume design energy & capacity are in same block */
+		bq27xxx_battery_update_dm_block(di, &bd,
+					BQ27XXX_DM_DESIGN_CAPACITY,
+					info->charge_full_design_uah / 1000);
+		bq27xxx_battery_update_dm_block(di, &bd,
+					BQ27XXX_DM_DESIGN_ENERGY,
+					info->energy_full_design_uwh / 1000);
+	}
+
+	if (info->voltage_min_design_uv != -EINVAL) {
+		bool same = bd.class == bt.class && bd.block == bt.block;
+		if (!same)
+			bq27xxx_battery_read_dm_block(di, &bt);
+		bq27xxx_battery_update_dm_block(di, same ? &bd : &bt,
+					BQ27XXX_DM_TERMINATE_VOLTAGE,
+					info->voltage_min_design_uv / 1000);
+	}
+
+	bq27xxx_battery_write_dm_block(di, &bd);
+	bq27xxx_battery_write_dm_block(di, &bt);
+}
+
+void bq27xxx_battery_settings(struct bq27xxx_device_info *di)
+{
+	struct power_supply_battery_info info = {};
+	unsigned int min, max;
+
+	/* functions don't exist for writing data so abort */
+	if (!di->bus.write || !di->bus.write_bulk)
+		return;
+
+	/* no settings to be set for this chipset so abort */
+	if (!bq27xxx_dm_regs[di->chip])
+		return;
+
+	if (bq27xxx_battery_set_seal_state(di, false) < 0)
+		return;
+
+	if (power_supply_get_battery_info(di->bat, &info) < 0)
+		goto out;
+
+	if (info.energy_full_design_uwh != info.charge_full_design_uah) {
+		if (info.energy_full_design_uwh == -EINVAL)
+			dev_warn(di->dev,
+				"missing battery:energy-full-design-microwatt-hours\n");
+		else if (info.charge_full_design_uah == -EINVAL)
+			dev_warn(di->dev,
+				"missing battery:charge-full-design-microamp-hours\n");
+	}
+
+	/* assume min == 0 */
+	max = bq27xxx_dm_regs[di->chip][BQ27XXX_DM_DESIGN_ENERGY].max;
+	if (info.energy_full_design_uwh > max * 1000) {
+		dev_err(di->dev,
+		       "invalid battery:energy-full-design-microwatt-hours %d\n",
+			info.energy_full_design_uwh);
+		info.energy_full_design_uwh = -EINVAL;
+	}
+
+	/* assume min == 0 */
+	max = bq27xxx_dm_regs[di->chip][BQ27XXX_DM_DESIGN_CAPACITY].max;
+	if (info.charge_full_design_uah > max * 1000) {
+		dev_err(di->dev,
+		       "invalid battery:charge-full-design-microamp-hours %d\n",
+			info.charge_full_design_uah);
+		info.charge_full_design_uah = -EINVAL;
+	}
+
+	min = bq27xxx_dm_regs[di->chip][BQ27XXX_DM_TERMINATE_VOLTAGE].min;
+	max = bq27xxx_dm_regs[di->chip][BQ27XXX_DM_TERMINATE_VOLTAGE].max;
+	if ((info.voltage_min_design_uv < min * 1000
+	  || info.voltage_min_design_uv > max * 1000)
+	  && info.voltage_min_design_uv != -EINVAL) {
+		dev_err(di->dev,
+		       "invalid battery:voltage-min-design-microvolt %d\n",
+			info.voltage_min_design_uv);
+		info.voltage_min_design_uv = -EINVAL;
+	}
+
+	if ((info.energy_full_design_uwh == -EINVAL
+	  || info.charge_full_design_uah == -EINVAL)
+	  && info.voltage_min_design_uv  == -EINVAL)
+		goto out;
+
+	bq27xxx_battery_set_config(di, &info);
+
+out:
+	bq27xxx_battery_set_seal_state(di, true);
+}
+
 /*
  * Return the battery State-of-Charge
  * Or < 0 if something fails.
@@ -1006,6 +1474,13 @@ static int bq27xxx_battery_get_property(struct power_supply *psy,
 	case POWER_SUPPLY_PROP_CHARGE_FULL_DESIGN:
 		ret = bq27xxx_simple_value(di->charge_design_full, val);
 		break;
+	/*
+	 * TODO: Implement these to make registers set from
+	 * power_supply_battery_info visible in sysfs.
+	 */
+	case POWER_SUPPLY_PROP_ENERGY_FULL_DESIGN:
+	case POWER_SUPPLY_PROP_VOLTAGE_MIN_DESIGN:
+		return -EINVAL;
 	case POWER_SUPPLY_PROP_CYCLE_COUNT:
 		ret = bq27xxx_simple_value(di->cache.cycle_count, val);
 		break;
@@ -1039,7 +1514,10 @@ static void bq27xxx_external_power_changed(struct power_supply *psy)
 int bq27xxx_battery_setup(struct bq27xxx_device_info *di)
 {
 	struct power_supply_desc *psy_desc;
-	struct power_supply_config psy_cfg = { .drv_data = di, };
+	struct power_supply_config psy_cfg = {
+		.of_node = di->dev->of_node,
+		.drv_data = di,
+	};
 
 	INIT_DELAYED_WORK(&di->work, bq27xxx_battery_poll);
 	mutex_init(&di->lock);
@@ -1064,6 +1542,7 @@ int bq27xxx_battery_setup(struct bq27xxx_device_info *di)
 
 	dev_info(di->dev, "support ver. %s enabled\n", DRIVER_VERSION);
 
+	bq27xxx_battery_settings(di);
 	bq27xxx_battery_update(di);
 
 	mutex_lock(&bq27xxx_list_lock);
-- 
2.9.3

[PATCH v9 8/8] power: bq27xxx_battery_i2c: Add I2C bulk read/write functions

[Liam Breck]

From: Matt Ranostay <matt@ranostay.consulting>

write(), read_bulk(), write_bulk() are required by bq27xxx_battery
devicetree code.

Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Liam Breck <kernel@networkimprov.net>
---
 drivers/power/supply/bq27xxx_battery_i2c.c | 82 +++++++++++++++++++++++++++++-
 1 file changed, 81 insertions(+), 1 deletion(-)

diff --git a/drivers/power/supply/bq27xxx_battery_i2c.c b/drivers/power/supply/bq27xxx_battery_i2c.c
index 7781ca9..4039b9d 100644
--- a/drivers/power/supply/bq27xxx_battery_i2c.c
+++ b/drivers/power/supply/bq27xxx_battery_i2c.c
@@ -38,7 +38,7 @@ static int bq27xxx_battery_i2c_read(struct bq27xxx_device_info *di, u8 reg,
 {
 	struct i2c_client *client = to_i2c_client(di->dev);
 	struct i2c_msg msg[2];
-	unsigned char data[2];
+	u8 data[2];
 	int ret;
 
 	if (!client->adapter)
@@ -68,6 +68,82 @@ static int bq27xxx_battery_i2c_read(struct bq27xxx_device_info *di, u8 reg,
 	return ret;
 }
 
+static int bq27xxx_battery_i2c_write(struct bq27xxx_device_info *di, u8 reg,
+				     int value, bool single)
+{
+	struct i2c_client *client = to_i2c_client(di->dev);
+	struct i2c_msg msg;
+	u8 data[4];
+	int ret;
+
+	if (!client->adapter)
+		return -ENODEV;
+
+	data[0] = reg;
+	if (single) {
+		data[1] = (u8) value;
+		msg.len = 2;
+	} else {
+		put_unaligned_le16(value, &data[1]);
+		msg.len = 3;
+	}
+
+	msg.buf = data;
+	msg.addr = client->addr;
+	msg.flags = 0;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0)
+		return ret;
+	if (ret != 1)
+		return -EINVAL;
+	return 0;
+}
+
+static int bq27xxx_battery_i2c_bulk_read(struct bq27xxx_device_info *di, u8 reg,
+					 u8 *data, int len)
+{
+	struct i2c_client *client = to_i2c_client(di->dev);
+	int ret;
+
+	if (!client->adapter)
+		return -ENODEV;
+
+	ret = i2c_smbus_read_i2c_block_data(client, reg, len, data);
+	if (ret < 0)
+		return ret;
+	if (ret != len)
+		return -EINVAL;
+	return 0;
+}
+
+static int bq27xxx_battery_i2c_bulk_write(struct bq27xxx_device_info *di,
+					  u8 reg, u8 *data, int len)
+{
+	struct i2c_client *client = to_i2c_client(di->dev);
+	struct i2c_msg msg;
+	u8 buf[33];
+	int ret;
+
+	if (!client->adapter)
+		return -ENODEV;
+
+	buf[0] = reg;
+	memcpy(&buf[1], data, len);
+
+	msg.buf = buf;
+	msg.addr = client->addr;
+	msg.flags = 0;
+	msg.len = len + 1;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	if (ret < 0)
+		return ret;
+	if (ret != 1)
+		return -EINVAL;
+	return 0;
+}
+
 static int bq27xxx_battery_i2c_probe(struct i2c_client *client,
 				     const struct i2c_device_id *id)
 {
@@ -95,7 +171,11 @@ static int bq27xxx_battery_i2c_probe(struct i2c_client *client,
 	di->dev = &client->dev;
 	di->chip = id->driver_data;
 	di->name = name;
+
 	di->bus.read = bq27xxx_battery_i2c_read;
+	di->bus.write = bq27xxx_battery_i2c_write;
+	di->bus.read_bulk = bq27xxx_battery_i2c_bulk_read;
+	di->bus.write_bulk = bq27xxx_battery_i2c_bulk_write;
 
 	ret = bq27xxx_battery_setup(di);
 	if (ret)
-- 
2.9.3