From: Juri Lelli <juri.lelli@arm.com>
To: linux-kernel@vger.kernel.org
Cc: linux-pm@vger.kernel.org, rjw@rjwysocki.net,
viresh.kumar@linaro.org, peterz@infradead.org,
vincent.guittot@linaro.org, juri.lelli@arm.com,
"Rafael J . Wysocki" <rafael.j.wysocki@intel.com>
Subject: [PATCH] sched/cpufreq_schedutil: use now as reference when aggregating shared policy requests
Date: Wed, 3 May 2017 14:30:48 +0100 [thread overview]
Message-ID: <20170503133048.8742-1-juri.lelli@arm.com> (raw)
Currently, sugov_next_freq_shared() uses last_freq_update_time as a
reference to decide when to start considering CPU contributions as
stale.
However, since last_freq_update_time is set by the last CPU that issued
a frequency transition, this might cause problems in certain cases. In
practice, the detection of stale utilization values fails whenever the
CPU with such values was the last to update the policy. For example (and
please note again that the SCHED_CPUFREQ_RT flag is not the problem
here, but only the detection of after how much time that flag has to be
considered stale), suppose a policy with 2 CPUs:
CPU0 | CPU1
|
| RT task scheduled
| SCHED_CPUFREQ_RT is set
| CPU1->last_update = now
| freq transition to max
| last_freq_update_time = now
|
more than TICK_NSEC nsecs
|
a small CFS wakes up |
CPU0->last_update = now1 |
delta_ns(CPU0) < TICK_NSEC* |
CPU0's util is considered |
delta_ns(CPU1) = |
last_freq_update_time - |
CPU1->last_update = 0 |
< TICK_NSEC |
CPU1 is still considered |
CPU1->SCHED_CPUFREQ_RT is set |
we stay at max (until CPU1 |
exits from idle) |
* delta_ns is actually negative as now1 > last_freq_update_time
While last_freq_update_time is a sensible reference for rate limiting,
it doesn't seem to be useful for working around stale CPU states.
Fix the problem by always considering now (time) as the reference for
deciding when CPUs have stale contributions.
Signed-off-by: Juri Lelli <juri.lelli@arm.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
---
kernel/sched/cpufreq_schedutil.c | 7 +++----
1 file changed, 3 insertions(+), 4 deletions(-)
diff --git a/kernel/sched/cpufreq_schedutil.c b/kernel/sched/cpufreq_schedutil.c
index 76877a62b5fa..622eed1b7658 100644
--- a/kernel/sched/cpufreq_schedutil.c
+++ b/kernel/sched/cpufreq_schedutil.c
@@ -245,11 +245,10 @@ static void sugov_update_single(struct update_util_data *hook, u64 time,
sugov_update_commit(sg_policy, time, next_f);
}
-static unsigned int sugov_next_freq_shared(struct sugov_cpu *sg_cpu)
+static unsigned int sugov_next_freq_shared(struct sugov_cpu *sg_cpu, u64 time)
{
struct sugov_policy *sg_policy = sg_cpu->sg_policy;
struct cpufreq_policy *policy = sg_policy->policy;
- u64 last_freq_update_time = sg_policy->last_freq_update_time;
unsigned long util = 0, max = 1;
unsigned int j;
@@ -265,7 +264,7 @@ static unsigned int sugov_next_freq_shared(struct sugov_cpu *sg_cpu)
* enough, don't take the CPU into account as it probably is
* idle now (and clear iowait_boost for it).
*/
- delta_ns = last_freq_update_time - j_sg_cpu->last_update;
+ delta_ns = time - j_sg_cpu->last_update;
if (delta_ns > TICK_NSEC) {
j_sg_cpu->iowait_boost = 0;
continue;
@@ -309,7 +308,7 @@ static void sugov_update_shared(struct update_util_data *hook, u64 time,
if (flags & SCHED_CPUFREQ_RT_DL)
next_f = sg_policy->policy->cpuinfo.max_freq;
else
- next_f = sugov_next_freq_shared(sg_cpu);
+ next_f = sugov_next_freq_shared(sg_cpu, time);
sugov_update_commit(sg_policy, time, next_f);
}
--
2.10.0
next reply other threads:[~2017-05-03 13:30 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2017-05-03 13:30 Juri Lelli [this message]
2017-05-04 14:29 ` [PATCH] sched/cpufreq_schedutil: use now as reference when aggregating shared policy requests Rafael J. Wysocki
2017-05-04 14:40 ` Juri Lelli
2017-05-04 14:41 ` Vincent Guittot
2017-05-05 6:06 ` Viresh Kumar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20170503133048.8742-1-juri.lelli@arm.com \
--to=juri.lelli@arm.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=peterz@infradead.org \
--cc=rafael.j.wysocki@intel.com \
--cc=rjw@rjwysocki.net \
--cc=vincent.guittot@linaro.org \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox