[PATCH v2 0/8] Allwinner: A523: add support for A523 THS0/1 controllers

[PATCH v2 0/8] Allwinner: A523: add support for A523 THS0/1 controllers

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

This patch series adds temperature sensor support for the Allwinner A523
family of processors (same die with H728/A527/T527)

Changes:
1) dt-bindings: nvmem: SID: Add binding for A523 SID controller
 - added new patch

2) dt-bindings: thermal: sun8i: Add A523 THS0/1 controllers
 - changed clock order
 - added additional nvmem cell with calibration data
 - added requirements for new controllers
 - added description

3) thermal/drivers/sun8i: add gpadc clock
 - removed unnecessary call to clk_prepare_enable() since
 devm_clk_get_enabled()includes this

4) thermal/drivers/sun8i: replace devm_reset_control_get to
 - original function replaced with devm_reset_control_get_shared_deasserted()
 - removed some of the repetitive code executed by 
 devm_reset_control_get_shared_deasserted()

5) thermal/drivers/sun8i: get calibration data from two nvmem cells
 - added possibility to get calibration data from two independent cells

6) thermal/drivers/sun8i: Add support for A523 THS0/1 controllers
 - removed magic digits
 - changed description of calibration data procedure for A523
 - changed numbers of array elements with calibration data

7) arm64: dts: allwinner: A523: Add SID controller node
 - fix typo (sun50i->sun55i)

8) arm64: dts: allwinner: A523: Add thermal sensors and zones
 - cell with calibration data divided into two
 - added passive trips for gpu
 - added information that information obtained from BSP

v1: https://lore.kernel.org/linux-sunxi/20250411003827.782544-1-iuncuim@gmail.com

Mikhail Kalashnikov (8):
  dt-bindings: nvmem: SID: Add binding for A523 SID controller
  dt-bindings: thermal: sun8i: Add A523 THS0/1 controllers
  thermal/drivers/sun8i: add gpadc clock
  thermal/drivers/sun8i: replace devm_reset_control_get to
    devm_reset_control_get_shared_deasserted
  thermal/drivers/sun8i: get calibration data from two nvmem cells
  thermal/drivers/sun8i: Add support for A523 THS0/1 controllers
  arm64: dts: allwinner: A523: Add SID controller node
  arm64: dts: allwinner: A523: Add thermal sensors and zones

 .../nvmem/allwinner,sun4i-a10-sid.yaml        |   1 +
 .../thermal/allwinner,sun8i-a83t-ths.yaml     |  49 +++-
 .../arm64/boot/dts/allwinner/sun55i-a523.dtsi | 162 ++++++++++++
 drivers/thermal/sun8i_thermal.c               | 240 ++++++++++++++----
 4 files changed, 406 insertions(+), 46 deletions(-)

-- 
2.49.0

[PATCH v2 0/8] Allwinner: A523: add support for A523 THS0/1 controllers

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

This patch series adds temperature sensor support for the Allwinner A523
family of processors (same die with H728/A527/T527)

Changes:
1) dt-bindings: nvmem: SID: Add binding for A523 SID controller
 - added new patch

2) dt-bindings: thermal: sun8i: Add A523 THS0/1 controllers
 - changed clock order
 - added additional nvmem cell with calibration data
 - added requirements for new controllers
 - added description

3) thermal/drivers/sun8i: add gpadc clock
 - removed unnecessary call to clk_prepare_enable() since
 devm_clk_get_enabled()includes this

4) thermal/drivers/sun8i: replace devm_reset_control_get to
 - original function replaced with devm_reset_control_get_shared_deasserted()
 - removed some of the repetitive code executed by 
 devm_reset_control_get_shared_deasserted()

5) thermal/drivers/sun8i: get calibration data from two nvmem cells
 - added possibility to get calibration data from two independent cells

6) thermal/drivers/sun8i: Add support for A523 THS0/1 controllers
 - removed magic digits
 - changed description of calibration data procedure for A523
 - changed numbers of array elements with calibration data

7) arm64: dts: allwinner: A523: Add SID controller node
 - fix typo (sun50i->sun55i)

8) arm64: dts: allwinner: A523: Add thermal sensors and zones
 - cell with calibration data divided into two
 - added passive trips for gpu
 - added information that information obtained from BSP

v1: https://lore.kernel.org/linux-sunxi/20250411003827.782544-1-iuncuim@gmail.com

Mikhail Kalashnikov (8):
  dt-bindings: nvmem: SID: Add binding for A523 SID controller
  dt-bindings: thermal: sun8i: Add A523 THS0/1 controllers
  thermal/drivers/sun8i: add gpadc clock
  thermal/drivers/sun8i: replace devm_reset_control_get to
    devm_reset_control_get_shared_deasserted
  thermal/drivers/sun8i: get calibration data from two nvmem cells
  thermal/drivers/sun8i: Add support for A523 THS0/1 controllers
  arm64: dts: allwinner: A523: Add SID controller node
  arm64: dts: allwinner: A523: Add thermal sensors and zones

 .../nvmem/allwinner,sun4i-a10-sid.yaml        |   1 +
 .../thermal/allwinner,sun8i-a83t-ths.yaml     |  49 +++-
 .../arm64/boot/dts/allwinner/sun55i-a523.dtsi | 162 ++++++++++++
 drivers/thermal/sun8i_thermal.c               | 240 ++++++++++++++----
 4 files changed, 406 insertions(+), 46 deletions(-)

-- 
2.49.0

[PATCH v2 1/8] dt-bindings: nvmem: SID: Add binding for A523 SID controller

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

The SID controller should be compatible with A64 and others SoC with 0x200
offset.

Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
---
 .../devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml       | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
index 4424c3c5e..f67470b8a 100644
--- a/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
+++ b/Documentation/devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml
@@ -27,6 +27,7 @@ properties:
           - enum:
               - allwinner,sun50i-a100-sid
               - allwinner,sun50i-h616-sid
+              - allwinner,sun55i-a523-sid
           - const: allwinner,sun50i-a64-sid
       - const: allwinner,sun50i-h5-sid
       - const: allwinner,sun50i-h6-sid
-- 
2.49.0

[PATCH v2 2/8] dt-bindings: thermal: sun8i: Add A523 THS0/1 controllers

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

Add a binding for D1/T113s thermal sensor controller. Add dt-bindings
description of the thermal sensors in the A523 processor.
The controllers require activation of the additional frequency of the
associated gpadc controller, so a new clock property has been added.

The calibration data is split into two cells that are in different areas
of nvmem. Both controllers require access to both memory cell, so a new
property nvmem-cells has been added. To maintain backward compatibility,
the name of the old cell remains the same and the new nvmem-cell-names is
called calibration-second-part

Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
---
 .../thermal/allwinner,sun8i-a83t-ths.yaml     | 49 +++++++++++++++++--
 1 file changed, 46 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
index 3e61689f6..80657435a 100644
--- a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
+++ b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
@@ -24,18 +24,22 @@ properties:
       - allwinner,sun50i-h5-ths
       - allwinner,sun50i-h6-ths
       - allwinner,sun50i-h616-ths
+      - allwinner,sun55i-a523-ths0
+      - allwinner,sun55i-a523-ths1
 
   clocks:
     minItems: 1
     items:
       - description: Bus Clock
       - description: Module Clock
+      - description: GPADC Clock
 
   clock-names:
     minItems: 1
     items:
       - const: bus
       - const: mod
+      - const: gpadc
 
   reg:
     maxItems: 1
@@ -47,11 +51,16 @@ properties:
     maxItems: 1
 
   nvmem-cells:
-    maxItems: 1
-    description: Calibration data for thermal sensors
+    minItems: 1
+    items:
+      - description: Calibration data for thermal sensors
+      - description: Additional cell in case of separate calibration data
 
   nvmem-cell-names:
-    const: calibration
+    minItems: 1
+    items:
+      - const: calibration
+      - const: calibration-second-part
 
   allwinner,sram:
     maxItems: 1
@@ -107,6 +116,7 @@ allOf:
             enum:
               - allwinner,sun8i-h3-ths
               - allwinner,sun20i-d1-ths
+              - allwinner,sun55i-a523-ths0
 
     then:
       properties:
@@ -132,6 +142,26 @@ allOf:
         - clock-names
         - resets
 
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - allwinner,sun55i-a523-ths0
+              - allwinner,sun55i-a523-ths1
+    then:
+      properties:
+        clocks:
+          minItems: 2
+        clock-names:
+          items:
+            - const: bus
+            - const: gpadc
+        nvmem-cells:
+          minItems: 2
+        nvmem-cell-names:
+          minItems: 2
+
 required:
   - compatible
   - reg
@@ -176,4 +206,17 @@ examples:
         #thermal-sensor-cells = <1>;
     };
 
+  - |
+    thermal-sensor@2009400 {
+      compatible = "allwinner,sun55i-a523-ths1";
+      reg = <0x02009400 0x400>;
+      interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+      clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_GPADC1>;
+      clock-names = "bus", "gpadc";
+      resets = <&ccu RST_BUS_THS>;
+      nvmem-cells = <&ths_calibration0>, <&ths_calibration1>;
+      nvmem-cell-names = "calibration",
+             "calibration-second-part";
+      #thermal-sensor-cells = <1>;
+    };
 ...
-- 
2.49.0

[PATCH v2 3/8] thermal/drivers/sun8i: add gpadc clock

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

Some processors (e.g. Allwinner A523) require GPADC clocking activation for
temperature sensors to work. So let's add support for enabling it.

Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
---
 drivers/thermal/sun8i_thermal.c | 14 +++++++++++---
 1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 226747906..45aaf5348 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -66,8 +66,9 @@ struct tsensor {
 };
 
 struct ths_thermal_chip {
-	bool            has_mod_clk;
-	bool            has_bus_clk_reset;
+	bool		has_gpadc_clk;
+	bool		has_mod_clk;
+	bool		has_bus_clk_reset;
 	bool		needs_sram;
 	int		sensor_num;
 	int		offset;
@@ -89,7 +90,8 @@ struct ths_device {
 	struct regmap_field			*sram_regmap_field;
 	struct reset_control			*reset;
 	struct clk				*bus_clk;
-	struct clk                              *mod_clk;
+	struct clk				*mod_clk;
+	struct clk				*gpadc_clk;
 	struct tsensor				sensor[MAX_SENSOR_NUM];
 };
 
@@ -417,6 +419,12 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
 	if (ret)
 		return ret;
 
+	if (tmdev->chip->has_gpadc_clk) {
+		tmdev->gpadc_clk = devm_clk_get_enabled(&pdev->dev, "gpadc");
+		if (IS_ERR(tmdev->gpadc_clk))
+			return PTR_ERR(tmdev->gpadc_clk);
+	}
+
 	if (tmdev->chip->needs_sram) {
 		struct regmap *regmap;
 
-- 
2.49.0

[PATCH v2 4/8] thermal/drivers/sun8i: replace devm_reset_control_get to devm_reset_control_get_shared_deasserted

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

The A523 processor has two temperature controllers, but they share a common
reset line. We can to use devm_reset_control_get_shared_deasserted() instead
of devm_reset_control_get(). This will simplify the driver.

Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
---
 drivers/thermal/sun8i_thermal.c | 16 +---------------
 1 file changed, 1 insertion(+), 15 deletions(-)

diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 45aaf5348..bdd15ee45 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -344,11 +344,6 @@ static int sun8i_ths_calibrate(struct ths_device *tmdev)
 	return ret;
 }
 
-static void sun8i_ths_reset_control_assert(void *data)
-{
-	reset_control_assert(data);
-}
-
 static struct regmap *sun8i_ths_get_sram_regmap(struct device_node *node)
 {
 	struct platform_device *sram_pdev;
@@ -391,19 +386,10 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
 		return PTR_ERR(tmdev->regmap);
 
 	if (tmdev->chip->has_bus_clk_reset) {
-		tmdev->reset = devm_reset_control_get(dev, NULL);
+		tmdev->reset = devm_reset_control_get_shared_deasserted(dev, NULL);
 		if (IS_ERR(tmdev->reset))
 			return PTR_ERR(tmdev->reset);
 
-		ret = reset_control_deassert(tmdev->reset);
-		if (ret)
-			return ret;
-
-		ret = devm_add_action_or_reset(dev, sun8i_ths_reset_control_assert,
-					       tmdev->reset);
-		if (ret)
-			return ret;
-
 		tmdev->bus_clk = devm_clk_get_enabled(&pdev->dev, "bus");
 		if (IS_ERR(tmdev->bus_clk))
 			return PTR_ERR(tmdev->bus_clk);
-- 
2.49.0

[PATCH v2 5/8] thermal/drivers/sun8i: get calibration data from two nvmem cells

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

The A523 processor has calibration data in two nvmem cell. To be able to add
support, the ability to add data from two cells into one array must be added.

Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
---
 drivers/thermal/sun8i_thermal.c | 77 ++++++++++++++++++++++-----------
 1 file changed, 52 insertions(+), 25 deletions(-)

diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index bdd15ee45..3f57f1a6b 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -303,43 +303,70 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev,
 
 static int sun8i_ths_calibrate(struct ths_device *tmdev)
 {
-	struct nvmem_cell *calcell;
+	struct nvmem_cell *calcell = NULL;
 	struct device *dev = tmdev->dev;
-	u16 *caldata;
-	size_t callen;
+	struct device_node *np = dev_of_node(dev);
+	struct property *prop;
+	const char *cellname;
+	u8 *caldata = NULL;
+	size_t callen = 0;
 	int ret = 0;
 
-	calcell = nvmem_cell_get(dev, "calibration");
-	if (IS_ERR(calcell)) {
-		if (PTR_ERR(calcell) == -EPROBE_DEFER)
-			return -EPROBE_DEFER;
-		/*
-		 * Even if the external calibration data stored in sid is
-		 * not accessible, the THS hardware can still work, although
-		 * the data won't be so accurate.
-		 *
-		 * The default value of calibration register is 0x800 for
-		 * every sensor, and the calibration value is usually 0x7xx
-		 * or 0x8xx, so they won't be away from the default value
-		 * for a lot.
-		 *
-		 * So here we do not return error if the calibration data is
-		 * not available, except the probe needs deferring.
-		 */
-		goto out;
+	of_property_for_each_string(np, "nvmem-cell-names", prop, cellname) {
+		size_t len;
+		u8 *caldatapart;
+
+  		calcell = of_nvmem_cell_get(np, cellname);
+  		if (IS_ERR(calcell)) {
+			if (PTR_ERR(calcell) == -EPROBE_DEFER)
+				return -EPROBE_DEFER;
+			/*
+			* Even if the external calibration data stored in sid is
+			* not accessible, the THS hardware can still work, although
+			* the data won't be so accurate.
+			*
+			* The default value of calibration register is 0x800 for
+			* every sensor, and the calibration value is usually 0x7xx
+			* or 0x8xx, so they won't be away from the default value
+			* for a lot.
+			*
+			* So here we do not return error if the calibration data is
+			* not available, except the probe needs deferring.
+			*/
+			goto out;
+		}
+
+		caldatapart = nvmem_cell_read(calcell, &len);
+		nvmem_cell_put(calcell);
+		calcell = NULL;
+		if (IS_ERR(caldatapart)) {
+			ret = PTR_ERR(caldatapart);
+			goto out;
+		}
+
+		caldata = devm_krealloc(dev, caldata, callen + len, GFP_KERNEL);
+		if (!caldata) {
+			kfree(caldatapart);
+			ret = -ENOMEM;
+			goto out;
+		}
+
+		memcpy(caldata + callen, caldatapart, len);
+		callen += len;
+		kfree(caldatapart);
 	}
 
-	caldata = nvmem_cell_read(calcell, &callen);
 	if (IS_ERR(caldata)) {
 		ret = PTR_ERR(caldata);
 		goto out;
 	}
 
-	tmdev->chip->calibrate(tmdev, caldata, callen);
+	tmdev->chip->calibrate(tmdev, (u16 *)caldata, callen);
 
-	kfree(caldata);
+	devm_kfree(dev, caldata);
+	caldata = NULL;
 out:
-	if (!IS_ERR(calcell))
+	if (calcell && !IS_ERR(calcell))
 		nvmem_cell_put(calcell);
 	return ret;
 }
-- 
2.49.0

[PATCH v2 6/8] thermal/drivers/sun8i: Add support for A523 THS0/1 controllers

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

The A523 processor has two temperature controllers, THS0 and THS1.

THS0 has only one temperature sensor, which is located in the DRAM.

THS1 does have 3 sensors:
ths1_0 - "big" cores
ths1_1 - "little" cores
ths1_2 - gpu

The datasheet mentions a fourth sensor in the NPU, but lacks any registers
for operation other than calibration registers. The vendor code reads the 
value from ths1_2, but uses separate calibration data, so we get two different
values from real one.

Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
---
 drivers/thermal/sun8i_thermal.c | 133 ++++++++++++++++++++++++++++++++
 1 file changed, 133 insertions(+)

diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 3f57f1a6b..f74567cbf 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -59,6 +59,12 @@
 #define SUN50I_H6_THS_PC_TEMP_PERIOD(x)		((GENMASK(19, 0) & (x)) << 12)
 #define SUN50I_H6_THS_DATA_IRQ_STS(x)		BIT(x)
 
+#define SUN55I_A523_DELIMITER			0x7c8
+#define SUN55I_A523_OFFSET_ABOVE		2736
+#define SUN55I_A523_OFFSET_BELOW		2825
+#define SUN55I_A523_SCALE_ABOVE			74
+#define SUN55I_A523_SCALE_BELOW			65
+
 struct tsensor {
 	struct ths_device		*tmdev;
 	struct thermal_zone_device	*tzd;
@@ -116,6 +122,15 @@ static int sun50i_h5_calc_temp(struct ths_device *tmdev,
 		return -1590 * reg / 10 + 276000;
 }
 
+static int sun55i_a523_calc_temp(struct ths_device *tmdev,
+					int id, int reg)
+{
+	if (reg >= SUN55I_A523_DELIMITER)
+		return SUN55I_A523_SCALE_ABOVE * (SUN55I_A523_OFFSET_ABOVE - reg);
+	else
+		return SUN55I_A523_SCALE_BELOW * (SUN55I_A523_OFFSET_BELOW - reg);
+}
+
 static int sun8i_ths_get_temp(struct thermal_zone_device *tz, int *temp)
 {
 	struct tsensor *s = thermal_zone_device_priv(tz);
@@ -301,6 +316,97 @@ static int sun50i_h6_ths_calibrate(struct ths_device *tmdev,
 	return 0;
 }
 
+/*
+ * The A523 nvmem calibration values. The ths1_3 is not used as it
+ * doesn't have its own sensor and doesn't have any internal switch.
+ * Instead, the value from the ths1_2 sensor is used, which gives the
+ * illusion of an independent sensor for NPU and GPU when using
+ * different calibration values.
+ *
+ * efuse layout 0x38-0x3F (caldata[0..3]):
+ *     caldata[0]      caldata[1]      caldata[2]      caldata[3]
+ * 0               16      24      32  36          48          60 64
+ * +---------------+---------------+---------------+---------------+
+ * |               |       |   temp    |  ths1_0   |  ths1_1   |   +
+ * +---------------+---------------+---------------+---------------+
+ *
+ * efuse layout 0x44-0x4B (caldata[4..7]):
+ *     caldata[4]      caldata[5]      caldata[6]      caldata[7]
+ * 0           12  16      24      32  36          48             64
+ * +---------------+---------------+---------------+---------------+
+ * |  ths1_2   |  ths1_3   |    ths0   |           |               +
+ * +---------------+---------------+---------------+---------------+
+ */
+static int sun55i_a523_ths_calibrate(struct ths_device *tmdev,
+				   u16 *caldata, int callen)
+{
+	struct device *dev = tmdev->dev;
+	int i, ft_temp;
+
+	if (!caldata[0])
+		return -EINVAL;
+
+	ft_temp = (((caldata[2] << 8) | (caldata[1] >> 8)) & FT_TEMP_MASK) * 100;
+
+	for (i = 0; i < tmdev->chip->sensor_num; i++) {
+		int sensor_reg, sensor_temp, cdata, offset;
+		/*
+		 * Chips ths0 and ths1 have common parameters for value
+		 * calibration. To separate them we can use the number of
+		 * temperature sensors on each chip.
+		 * For ths0 this value is 1.
+		 */
+		if (tmdev->chip->sensor_num == 1) {
+			sensor_reg = ((caldata[5] >> 8) | (caldata[6] << 8)) & TEMP_CALIB_MASK;
+		} else {
+			switch (i) {
+			case 0:
+				sensor_reg = (caldata[2] >> 4) & TEMP_CALIB_MASK;
+				break;
+			case 1:
+				sensor_reg = caldata[3] & TEMP_CALIB_MASK;
+				break;
+			case 2:
+				sensor_reg = caldata[4] & TEMP_CALIB_MASK;
+				break;
+			default:
+				sensor_reg = 0;
+				break;
+			}
+		}
+
+		sensor_temp = tmdev->chip->calc_temp(tmdev, i, sensor_reg);
+
+		/*
+		 * Calibration data is CALIBRATE_DEFAULT - (calculated
+		 * temperature from sensor reading at factory temperature
+		 * minus actual factory temperature) * X (scale from
+		 * temperature to register values)
+		 */
+		cdata = CALIBRATE_DEFAULT -
+			((sensor_temp - ft_temp) / SUN55I_A523_SCALE_ABOVE);
+
+		if (cdata & ~TEMP_CALIB_MASK) {
+			/*
+			 * Calibration value more than 12-bit, but calibration
+			 * register is 12-bit. In this case, ths hardware can
+			 * still work without calibration, although the data
+			 * won't be so accurate.
+			 */
+			dev_warn(dev, "sensor%d is not calibrated.\n", i);
+			continue;
+		}
+
+		offset = (i % 2) * 16;
+		regmap_update_bits(tmdev->regmap,
+				   SUN50I_H6_THS_TEMP_CALIB + (i / 2 * 4),
+				   TEMP_CALIB_MASK << offset,
+				   cdata << offset);
+	}
+
+	return 0;
+}
+
 static int sun8i_ths_calibrate(struct ths_device *tmdev)
 {
 	struct nvmem_cell *calcell = NULL;
@@ -730,6 +836,31 @@ static const struct ths_thermal_chip sun50i_h616_ths = {
 	.calc_temp = sun8i_ths_calc_temp,
 };
 
+/* The A523 has a shared reset line for both chips */
+static const struct ths_thermal_chip sun55i_a523_ths0 = {
+	.sensor_num = 1,
+	.has_bus_clk_reset = true,
+	.has_gpadc_clk = true,
+	.ft_deviation = 5000,
+	.temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+	.calibrate = sun55i_a523_ths_calibrate,
+	.init = sun50i_h6_thermal_init,
+	.irq_ack = sun50i_h6_irq_ack,
+	.calc_temp = sun55i_a523_calc_temp,
+};
+
+static const struct ths_thermal_chip sun55i_a523_ths1 = {
+	.sensor_num = 3,
+	.has_bus_clk_reset = true,
+	.has_gpadc_clk = true,
+	.ft_deviation = 5000,
+	.temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+	.calibrate = sun55i_a523_ths_calibrate,
+	.init = sun50i_h6_thermal_init,
+	.irq_ack = sun50i_h6_irq_ack,
+	.calc_temp = sun55i_a523_calc_temp,
+};
+
 static const struct of_device_id of_ths_match[] = {
 	{ .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths },
 	{ .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
@@ -740,6 +871,8 @@ static const struct of_device_id of_ths_match[] = {
 	{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
 	{ .compatible = "allwinner,sun20i-d1-ths", .data = &sun20i_d1_ths },
 	{ .compatible = "allwinner,sun50i-h616-ths", .data = &sun50i_h616_ths },
+	{ .compatible = "allwinner,sun55i-a523-ths0", .data = &sun55i_a523_ths0 },
+	{ .compatible = "allwinner,sun55i-a523-ths1", .data = &sun55i_a523_ths1 },
 	{ /* sentinel */ },
 };
 MODULE_DEVICE_TABLE(of, of_ths_match);
-- 
2.49.0

[PATCH v2 7/8] arm64: dts: allwinner: A523: Add SID controller node

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

The SID controller should be compatible with A64 and others SoC with 0x200
offset.

Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
---
 arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
index 8b7cbc2e7..295292d67 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
@@ -181,6 +181,14 @@ ccu: clock-controller@2001000 {
 			#reset-cells = <1>;
 		};
 
+		sid: efuse@3006000 {
+			compatible = "allwinner,sun55i-a523-sid",
+				     "allwinner,sun50i-a64-sid";
+			reg = <0x03006000 0x1000>;
+			#address-cells = <1>;
+			#size-cells = <1>;
+		};
+
 		mmc0: mmc@4020000 {
 			compatible = "allwinner,sun55i-a523-mmc",
 				     "allwinner,sun20i-d1-mmc";
-- 
2.49.0

[PATCH v2 8/8] arm64: dts: allwinner: A523: Add thermal sensors and zones

[iuncuim]

From: Mikhail Kalashnikov <iuncuim@gmail.com>

The A523 processor has two temperature controllers, THS0 and THS1.
THS0 has only one temperature sensor, which is located in the DRAM.

THS1 does have 3 sensors:
ths1_0 - "big" cores
ths1_1 - "little" cores
ths1_2 - gpu

Add the thermal sensor configuration and the thermal zones.
Trips temperature, polling-delay and sustainable-power parameters are derived
from the manufacturer's BSP.

Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
---
 .../arm64/boot/dts/allwinner/sun55i-a523.dtsi | 154 ++++++++++++++++++
 1 file changed, 154 insertions(+)

diff --git a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
index 295292d67..a1304c55c 100644
--- a/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
+++ b/arch/arm64/boot/dts/allwinner/sun55i-a523.dtsi
@@ -7,6 +7,7 @@
 #include <dt-bindings/clock/sun55i-a523-r-ccu.h>
 #include <dt-bindings/reset/sun55i-a523-ccu.h>
 #include <dt-bindings/reset/sun55i-a523-r-ccu.h>
+#include <dt-bindings/thermal/thermal.h>
 
 / {
 	interrupt-parent = <&gic>;
@@ -22,6 +23,7 @@ cpu0: cpu@0 {
 			device_type = "cpu";
 			reg = <0x000>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 		};
 
 		cpu1: cpu@100 {
@@ -29,6 +31,7 @@ cpu1: cpu@100 {
 			device_type = "cpu";
 			reg = <0x100>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 		};
 
 		cpu2: cpu@200 {
@@ -36,6 +39,7 @@ cpu2: cpu@200 {
 			device_type = "cpu";
 			reg = <0x200>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 		};
 
 		cpu3: cpu@300 {
@@ -43,6 +47,7 @@ cpu3: cpu@300 {
 			device_type = "cpu";
 			reg = <0x300>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 		};
 
 		cpu4: cpu@400 {
@@ -50,6 +55,7 @@ cpu4: cpu@400 {
 			device_type = "cpu";
 			reg = <0x400>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 		};
 
 		cpu5: cpu@500 {
@@ -57,6 +63,7 @@ cpu5: cpu@500 {
 			device_type = "cpu";
 			reg = <0x500>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 		};
 
 		cpu6: cpu@600 {
@@ -64,6 +71,7 @@ cpu6: cpu@600 {
 			device_type = "cpu";
 			reg = <0x600>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 		};
 
 		cpu7: cpu@700 {
@@ -71,6 +79,7 @@ cpu7: cpu@700 {
 			device_type = "cpu";
 			reg = <0x700>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 		};
 	};
 
@@ -181,12 +190,46 @@ ccu: clock-controller@2001000 {
 			#reset-cells = <1>;
 		};
 
+		ths1: thermal-sensor@2009400 {
+			compatible = "allwinner,sun55i-a523-ths1";
+			reg = <0x02009400 0x400>;
+			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_GPADC1>;
+			clock-names = "bus", "gpadc";
+			resets = <&ccu RST_BUS_THS>;
+			nvmem-cells = <&ths_calibration0>, <&ths_calibration1>;
+			nvmem-cell-names = "calibration",
+				     "calibration-second-part";
+			#thermal-sensor-cells = <1>;
+		};
+
+		ths0: thermal-sensor@200a000 {
+			compatible = "allwinner,sun55i-a523-ths0";
+			reg = <0x0200a000 0x400>;
+			interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_GPADC0>;
+			clock-names = "bus", "gpadc";
+			resets = <&ccu RST_BUS_THS>;
+			nvmem-cells = <&ths_calibration0>, <&ths_calibration1>;
+			nvmem-cell-names = "calibration",
+				     "calibration-second-part";
+			#thermal-sensor-cells = <0>;
+		};
+
 		sid: efuse@3006000 {
 			compatible = "allwinner,sun55i-a523-sid",
 				     "allwinner,sun50i-a64-sid";
 			reg = <0x03006000 0x1000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+
+			ths_calibration0: ths-calibration0@38 {
+				reg = <0x38 0x8>;
+			};
+
+			ths_calibration1: ths-calibration1@44 {
+				reg = <0x44 0x8>;
+			};
 		};
 
 		mmc0: mmc@4020000 {
@@ -644,4 +687,115 @@ rtc: rtc@7090000 {
 			#clock-cells = <1>;
 		};
 	};
+
+	thermal-zones {
+		cpu0_thermal: cpu0-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <1000>;
+			thermal-sensors = <&ths1 1>;
+			sustainable-power = <1200>;
+
+			trips {
+				cpu0_threshold: cpu-trip-0 {
+					temperature = <70000>;
+					type = "passive";
+					hysteresis = <0>;
+				};
+				cpu0_target: cpu-trip-1 {
+					temperature = <90000>;
+					type = "passive";
+					hysteresis = <0>;
+				};
+				cpu0_critical: cpu-trip-2 {
+					temperature = <110000>;
+					type = "critical";
+					hysteresis = <0>;
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu0_target>;
+					cooling-device = <&cpu0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		cpu4_thermal: cpu4-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <1000>;
+			thermal-sensors = <&ths1 0>;
+			sustainable-power = <1600>;
+
+			trips {
+				cpu4_threshold: cpu-trip-0 {
+					temperature = <70000>;
+					type = "passive";
+					hysteresis = <0>;
+				};
+				cpu4_target: cpu-trip-1 {
+					temperature = <90000>;
+					type = "passive";
+					hysteresis = <0>;
+				};
+				cpu4_critical: cpu-trip-2 {
+					temperature = <110000>;
+					type = "critical";
+					hysteresis = <0>;
+				};
+			};
+
+			cooling-maps {
+				map0 {
+					trip = <&cpu4_target>;
+					cooling-device = <&cpu4 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu5 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu6 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>,
+							 <&cpu7 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>;
+				};
+			};
+		};
+
+		gpu-thermal {
+			polling-delay-passive = <100>;
+			polling-delay = <1000>;
+			thermal-sensors = <&ths1 2>;
+			sustainable-power = <2400>;
+
+			gpu-trips {
+				gpu_temp_threshold: gpu-trip-0 {
+					temperature = <60000>;
+					type = "passive";
+					hysteresis = <0>;
+				};
+				gpu_temp_target: gpu-trip-1 {
+					temperature = <90000>;
+					type = "passive";
+					hysteresis = <0>;
+				};
+				gpu_temp_critical: gpu-trip-2 {
+					temperature = <110000>;
+					type = "critical";
+					hysteresis = <0>;
+				};
+			};
+		};
+
+		ddr-thermal {
+			polling-delay-passive = <0>;
+			polling-delay = <0>;
+			thermal-sensors = <&ths0>;
+
+			trips {
+				ddr_temp_critical: ddr-trip-0 {
+					temperature = <110000>;
+					type = "critical";
+					hysteresis = <0>;
+				};
+			};
+		};
+	};
 };
-- 
2.49.0

Re: [PATCH v2 4/8] thermal/drivers/sun8i: replace devm_reset_control_get to devm_reset_control_get_shared_deasserted

[Chen-Yu Tsai]

On Thu, Jul 3, 2025 at 11:13 PM iuncuim <iuncuim@gmail.com> wrote:
>
> From: Mikhail Kalashnikov <iuncuim@gmail.com>
>
> The A523 processor has two temperature controllers, but they share a common
> reset line. We can to use devm_reset_control_get_shared_deasserted() instead
> of devm_reset_control_get(). This will simplify the driver.

Nit: I'd probably write:

Make it shared with the shared variant of devm_reset_control_get(), and also
simplify the driver by switching to devm_reset_control_get_shared_deasserted().

> Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>

Reviewed-by: Chen-Yu Tsai <wens@csie.org>

Re: [PATCH v2 1/8] dt-bindings: nvmem: SID: Add binding for A523 SID controller

[Rob Herring (Arm)]

On Thu, 03 Jul 2025 23:11:25 +0800, iuncuim wrote:
> From: Mikhail Kalashnikov <iuncuim@gmail.com>
> 
> The SID controller should be compatible with A64 and others SoC with 0x200
> offset.
> 
> Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
> ---
>  .../devicetree/bindings/nvmem/allwinner,sun4i-a10-sid.yaml       | 1 +
>  1 file changed, 1 insertion(+)
> 

Acked-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v2 2/8] dt-bindings: thermal: sun8i: Add A523 THS0/1 controllers

[Rob Herring]

On Thu, Jul 03, 2025 at 11:11:26PM +0800, iuncuim wrote:
> From: Mikhail Kalashnikov <iuncuim@gmail.com>
> 
> Add a binding for D1/T113s thermal sensor controller. Add dt-bindings
> description of the thermal sensors in the A523 processor.
> The controllers require activation of the additional frequency of the
> associated gpadc controller, so a new clock property has been added.
> 
> The calibration data is split into two cells that are in different areas
> of nvmem. Both controllers require access to both memory cell, so a new
> property nvmem-cells has been added. To maintain backward compatibility,
> the name of the old cell remains the same and the new nvmem-cell-names is
> called calibration-second-part
> 
> Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
> ---
>  .../thermal/allwinner,sun8i-a83t-ths.yaml     | 49 +++++++++++++++++--
>  1 file changed, 46 insertions(+), 3 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
> index 3e61689f6..80657435a 100644
> --- a/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
> +++ b/Documentation/devicetree/bindings/thermal/allwinner,sun8i-a83t-ths.yaml
> @@ -24,18 +24,22 @@ properties:
>        - allwinner,sun50i-h5-ths
>        - allwinner,sun50i-h6-ths
>        - allwinner,sun50i-h616-ths
> +      - allwinner,sun55i-a523-ths0
> +      - allwinner,sun55i-a523-ths1
>  
>    clocks:
>      minItems: 1
>      items:
>        - description: Bus Clock
>        - description: Module Clock
> +      - description: GPADC Clock

You add a 3rd clock for everyone, but I don't see a conditional schema 
keeping the existing users at 2 clocks (maxItems: 2).

>  
>    clock-names:
>      minItems: 1
>      items:
>        - const: bus
>        - const: mod
> +      - const: gpadc
>  
>    reg:
>      maxItems: 1
> @@ -47,11 +51,16 @@ properties:
>      maxItems: 1
>  
>    nvmem-cells:
> -    maxItems: 1
> -    description: Calibration data for thermal sensors
> +    minItems: 1
> +    items:
> +      - description: Calibration data for thermal sensors
> +      - description: Additional cell in case of separate calibration data
>  
>    nvmem-cell-names:
> -    const: calibration
> +    minItems: 1
> +    items:
> +      - const: calibration
> +      - const: calibration-second-part
>  
>    allwinner,sram:
>      maxItems: 1
> @@ -107,6 +116,7 @@ allOf:
>              enum:
>                - allwinner,sun8i-h3-ths
>                - allwinner,sun20i-d1-ths
> +              - allwinner,sun55i-a523-ths0
>  
>      then:
>        properties:
> @@ -132,6 +142,26 @@ allOf:
>          - clock-names
>          - resets
>  
> +  - if:
> +      properties:
> +        compatible:
> +          contains:
> +            enum:
> +              - allwinner,sun55i-a523-ths0
> +              - allwinner,sun55i-a523-ths1
> +    then:
> +      properties:
> +        clocks:
> +          minItems: 2
> +        clock-names:
> +          items:
> +            - const: bus
> +            - const: gpadc

But if there's really still just 2 clocks, you need the last entry to be 
'enum: [ mod, gpadc ]'

Though really, how can this h/w now not have a clock for itself? 


> +        nvmem-cells:
> +          minItems: 2
> +        nvmem-cell-names:
> +          minItems: 2

Everyone else needs 'maxItems: 1'

> +
>  required:
>    - compatible
>    - reg
> @@ -176,4 +206,17 @@ examples:
>          #thermal-sensor-cells = <1>;
>      };
>  
> +  - |
> +    thermal-sensor@2009400 {
> +      compatible = "allwinner,sun55i-a523-ths1";
> +      reg = <0x02009400 0x400>;
> +      interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> +      clocks = <&ccu CLK_BUS_THS>, <&ccu CLK_GPADC1>;
> +      clock-names = "bus", "gpadc";
> +      resets = <&ccu RST_BUS_THS>;
> +      nvmem-cells = <&ths_calibration0>, <&ths_calibration1>;
> +      nvmem-cell-names = "calibration",
> +             "calibration-second-part";
> +      #thermal-sensor-cells = <1>;
> +    };
>  ...
> -- 
> 2.49.0
> 

Re: (subset) [PATCH v2 0/8] Allwinner: A523: add support for A523 THS0/1 controllers

[Srinivas Kandagatla]

On Thu, 03 Jul 2025 23:11:24 +0800, iuncuim wrote:
> From: Mikhail Kalashnikov <iuncuim@gmail.com>
> 
> This patch series adds temperature sensor support for the Allwinner A523
> family of processors (same die with H728/A527/T527)
> 
> Changes:
> 1) dt-bindings: nvmem: SID: Add binding for A523 SID controller
>  - added new patch
> 
> [...]

Applied, thanks!

[1/8] dt-bindings: nvmem: SID: Add binding for A523 SID controller
      commit: 68d386fb1ca01ddb4f70f07e3e7b8d51ef9743ac

Best regards,
-- 
Srinivas Kandagatla <srini@kernel.org>

Re: (subset) [PATCH v2 0/8] Allwinner: A523: add support for A523 THS0/1 controllers

[Chen-Yu Tsai]

On Thu, 03 Jul 2025 23:11:24 +0800, iuncuim wrote:
> This patch series adds temperature sensor support for the Allwinner A523
> family of processors (same die with H728/A527/T527)
> 
> Changes:
> 1) dt-bindings: nvmem: SID: Add binding for A523 SID controller
>  - added new patch
> 
> [...]

Applied to sunxi/dt-for-6.17 in local tree, thanks!

[7/8] arm64: dts: allwinner: A523: Add SID controller node
      commit: 082c6a2d06c0831d236760a29953355845eee988

Best regards,
-- 
Chen-Yu Tsai <wens@csie.org>

Re: [PATCH v2 3/8] thermal/drivers/sun8i: add gpadc clock

[Chen-Yu Tsai]

On Thu, Jul 3, 2025 at 11:13 PM iuncuim <iuncuim@gmail.com> wrote:
>
> From: Mikhail Kalashnikov <iuncuim@gmail.com>
>
> Some processors (e.g. Allwinner A523) require GPADC clocking activation for
> temperature sensors to work. So let's add support for enabling it.
>
> Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
> ---
>  drivers/thermal/sun8i_thermal.c | 14 +++++++++++---
>  1 file changed, 11 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
> index 226747906..45aaf5348 100644
> --- a/drivers/thermal/sun8i_thermal.c
> +++ b/drivers/thermal/sun8i_thermal.c
> @@ -66,8 +66,9 @@ struct tsensor {
>  };
>
>  struct ths_thermal_chip {
> -       bool            has_mod_clk;
> -       bool            has_bus_clk_reset;
> +       bool            has_gpadc_clk;
> +       bool            has_mod_clk;
> +       bool            has_bus_clk_reset;

What's with the random whitespace change here?

>         bool            needs_sram;
>         int             sensor_num;
>         int             offset;
> @@ -89,7 +90,8 @@ struct ths_device {
>         struct regmap_field                     *sram_regmap_field;
>         struct reset_control                    *reset;
>         struct clk                              *bus_clk;
> -       struct clk                              *mod_clk;
> +       struct clk                              *mod_clk;
> +       struct clk                              *gpadc_clk;

And here?

>         struct tsensor                          sensor[MAX_SENSOR_NUM];
>  };
>
> @@ -417,6 +419,12 @@ static int sun8i_ths_resource_init(struct ths_device *tmdev)
>         if (ret)
>                 return ret;
>
> +       if (tmdev->chip->has_gpadc_clk) {
> +               tmdev->gpadc_clk = devm_clk_get_enabled(&pdev->dev, "gpadc");
> +               if (IS_ERR(tmdev->gpadc_clk))
> +                       return PTR_ERR(tmdev->gpadc_clk);
> +       }
> +

This looks correct.


ChenYu

>         if (tmdev->chip->needs_sram) {
>                 struct regmap *regmap;
>
> --
> 2.49.0
>