Linux Power Management development
 help / color / mirror / Atom feed
From: Jiaxing Hu <gahing@gahingwoo.com>
To: tomeu@tomeuvizoso.net, heiko@sntech.de, robh@kernel.org,
	krzk+dt@kernel.org, conor+dt@kernel.org, joro@8bytes.org,
	will@kernel.org, robin.murphy@arm.com, ulfh@kernel.org,
	p.zabel@pengutronix.de, ogabbay@kernel.org
Cc: dri-devel@lists.freedesktop.org,
	linux-rockchip@lists.infradead.org, iommu@lists.linux.dev,
	linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
	linux-arm-kernel@lists.infradead.org,
	linux-kernel@vger.kernel.org, Jiaxing Hu <gahing@gahingwoo.com>
Subject: [RFC PATCH 0/9] accel/rocket: RK3576 NPU (RKNN) enablement
Date: Fri, 17 Jul 2026 20:50:38 +1200	[thread overview]
Message-ID: <20260717085220.3212274-1-gahing@gahingwoo.com> (raw)

This adds RK3576 NPU support to accel/rocket. RFC: the NPU brings up and
runs, but full inference is not correct yet, and I would rather get
feedback now than sit on it.

Tested on a Radxa ROCK 4D. The NPU probes, powers on, brings up its
IOMMUs, and runs jobs to completion (rocket + Mesa Teflon). Getting there
took a few fixes outside the driver too: a power-domain settle delay and
reset cycling (else a cold power-on throws an async SError), two rk_iommu
fixes for banks firmware leaves faulted, taking the full clock set on the
MMU nodes, and both NPU power domains on the core.

Not solved: only the first operation in a power session gives the right
answer. Every later one engages and DMAs its input, but the compute
output never lands, so the readback is the zero-point. I chased it
through the whole software surface (registers, IOMMU/TLB, cache,
power/clock/reset, dispatch) and it reproduces even with the driver
environment matched to the vendor's on the same kernel, so it looks to be
below software, in the fixed-function block. Traces available.

Two asks: review of the bring-up and the shared pmdomain/iommu changes;
and if anyone knows the RK3576 NPU internals, whether that
per-power-session arm can be driven from software at all.

The series is split by subsystem (binding, pmdomain, iommu, driver, DT).
The board DT keeps vdd_npu_s0 always-on for now; happy to switch to
proper runtime control if preferred.

I used Claude Opus 4.8 to help trim this series out of my debugging tree
and generate the diffs.

Jiaxing Hu (9):
  dt-bindings: npu: rockchip: add rockchip,rk3576-rknn-core
  pmdomain/rockchip: add optional per-domain power-on settle delay
  pmdomain/rockchip: cycle optional power-domain resets on power-on
  iommu/rockchip: skip orphaned-fault banks in rk_iommu_is_stall_active
  iommu/rockchip: skip orphaned-fault banks in CMD_ENABLE_STALL dispatch
  iommu/rockchip: take all DT clocks
  accel/rocket: add RK3576 NPU (RKNN) support
  arm64: dts: rockchip: rk3576: add NPU (RKNN) nodes
  arm64: dts: rockchip: rk3576-rock-4d: enable NPU

 .../npu/rockchip,rk3588-rknn-core.yaml        |   2 +-
 .../boot/dts/rockchip/rk3576-rock-4d.dts      |  16 ++
 arch/arm64/boot/dts/rockchip/rk3576.dtsi      |  78 ++++++++-
 drivers/accel/rocket/rocket_core.c            |  43 ++++-
 drivers/accel/rocket/rocket_core.h            |  22 ++-
 drivers/accel/rocket/rocket_device.c          |   4 +
 drivers/accel/rocket/rocket_drv.c             |   1 +
 drivers/accel/rocket/rocket_job.c             | 154 ++++++++++++++----
 drivers/iommu/rockchip-iommu.c                |  66 +++++---
 drivers/pmdomain/rockchip/pm-domains.c        |  68 +++++---
 10 files changed, 367 insertions(+), 87 deletions(-)

-- 
2.43.0


             reply	other threads:[~2026-07-17  8:52 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-07-17  8:50 Jiaxing Hu [this message]
2026-07-17  8:50 ` [RFC PATCH 1/9] dt-bindings: npu: rockchip: add rockchip,rk3576-rknn-core Jiaxing Hu
2026-07-17 10:02   ` Chaoyi Chen
2026-07-17  8:50 ` [RFC PATCH 2/9] pmdomain/rockchip: add optional per-domain power-on settle delay Jiaxing Hu
2026-07-17  8:50 ` [RFC PATCH 3/9] pmdomain/rockchip: cycle optional power-domain resets on power-on Jiaxing Hu
2026-07-17  8:50 ` [RFC PATCH 4/9] iommu/rockchip: skip orphaned-fault banks in rk_iommu_is_stall_active Jiaxing Hu
2026-07-17 10:15   ` Chaoyi Chen
2026-07-17  8:50 ` [RFC PATCH 5/9] iommu/rockchip: skip orphaned-fault banks in CMD_ENABLE_STALL dispatch Jiaxing Hu
2026-07-17  8:50 ` [RFC PATCH 6/9] iommu/rockchip: take all DT clocks Jiaxing Hu
2026-07-17 10:19   ` Chaoyi Chen
2026-07-17  8:50 ` [RFC PATCH 7/9] accel/rocket: add RK3576 NPU (RKNN) support Jiaxing Hu
2026-07-17 10:29   ` Chaoyi Chen
2026-07-17  8:50 ` [RFC PATCH 8/9] arm64: dts: rockchip: rk3576: add NPU (RKNN) nodes Jiaxing Hu
2026-07-17  8:50 ` [RFC PATCH 9/9] arm64: dts: rockchip: rk3576-rock-4d: enable NPU Jiaxing Hu

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20260717085220.3212274-1-gahing@gahingwoo.com \
    --to=gahing@gahingwoo.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=dri-devel@lists.freedesktop.org \
    --cc=heiko@sntech.de \
    --cc=iommu@lists.linux.dev \
    --cc=joro@8bytes.org \
    --cc=krzk+dt@kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=linux-rockchip@lists.infradead.org \
    --cc=ogabbay@kernel.org \
    --cc=p.zabel@pengutronix.de \
    --cc=robh@kernel.org \
    --cc=robin.murphy@arm.com \
    --cc=tomeu@tomeuvizoso.net \
    --cc=ulfh@kernel.org \
    --cc=will@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox