[PATCH v7 2/3] arm64: dts: qcom: eliza-evk: Add PCIe0 with M.2 E key connector

[Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>]

The Eliza EVK board features an M.2 E key connector connected to PCIe0.
Enable the PCIe0 root port and its QMP PHY with the necessary RPMH
regulator supplies. The M.2 slot's 3.3V supply rail is GPIO-controlled
via a TCA9538 I/O expander on I2C4.

The M.2 E key slot hosts a WLAN card connected over PCIe and a Bluetooth
device connected over UART. Model the connector using the
pcie-m2-e-connector binding, wiring the PCIe root port and UART5 for
the respective interfaces.

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Bartosz Golaszewski <bartosz.golaszewski@oss.qualcomm.com>
Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/eliza-evk.dtsi | 116 ++++++++++++++++++++++++++++++++
 1 file changed, 116 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/eliza-evk.dtsi b/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
index e47b24f8b827..b35fffb50976 100644
--- a/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
+++ b/arch/arm64/boot/dts/qcom/eliza-evk.dtsi
@@ -11,6 +11,92 @@ aliases {
 	chosen {
 		stdout-path = "serial0:115200n8";
 	};
+
+	vreg_pcie_m_3p3: regulator-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vreg_3p3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&gpio_expander1 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+	};
+
+	connector-0 {
+		compatible = "pcie-m2-e-connector";
+		vpcie3v3-supply = <&vreg_pcie_m_3p3>;
+		w-disable1-gpios = <&tlmm 35 GPIO_ACTIVE_LOW>;
+		w-disable2-gpios = <&pm8550vs_g_gpios 4 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&m2_w_disable1>, <&m2_w_disable2>;
+		pinctrl-names = "default";
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				m2_e_pcie_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&pcieport0_ep>;
+				};
+			};
+
+			port@3 {
+				reg = <3>;
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				m2_e_uart_ep: endpoint@0 {
+					reg = <0>;
+					remote-endpoint = <&uart5_ep>;
+				};
+			};
+		};
+	};
+};
+
+&i2c4 {
+	pinctrl-0 = <&qup_i2c4_data_clk>;
+	pinctrl-names = "default";
+
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	gpio_expander1: gpio@3c {
+		compatible = "ti,tca9538";
+		#gpio-cells = <2>;
+		gpio-controller;
+		reg = <0x3c>;
+	};
+};
+
+&pcie0 {
+	status = "okay";
+};
+
+&pcie0_phy {
+	vdda-phy-supply = <&vreg_l1k>;
+	vdda-pll-supply = <&vreg_l3k>;
+
+	status = "okay";
+};
+
+&pcie0_port0 {
+	wake-gpios = <&tlmm 114 GPIO_ACTIVE_LOW>;
+	reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
+
+	port {
+		pcieport0_ep: endpoint {
+			remote-endpoint = <&m2_e_pcie_ep>;
+		};
+	};
 };
 
 &uart13 {
@@ -18,3 +104,33 @@ &uart13 {
 
 	status = "okay";
 };
+
+&uart5 {
+	status = "okay";
+
+	port {
+		uart5_ep: endpoint {
+			remote-endpoint = <&m2_e_uart_ep>;
+		};
+	};
+};
+
+&pm8550vs_g_gpios {
+	m2_w_disable2: m2-w-disable2-state {
+		pins = "gpio4";
+		function = "normal";
+		input-disable;
+		output-enable;
+		bias-disable;
+		power-source = <2>;
+	};
+};
+
+&tlmm {
+	m2_w_disable1: m2-w-disable1-state {
+		pins = "gpio35";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+};

-- 
2.34.1