Re: Re: [PATCHv8 1/9] devfreq: event: Add new devfreq_event class to provide basic data for devfreq governor

Re: Re: [PATCHv8 1/9] devfreq: event: Add new devfreq_event class to provide basic data for devfreq governor

[MyungJoo Ham]

>  
> Dear Myungjoo,
>
>On 01/20/2015 01:34 PM, MyungJoo Ham wrote:
>>>   
[]
>>> +
>>> +	mutex_lock(&edev->lock);
>>> +	if (edev->desc->ops && edev->desc->ops->enable) {
>>> +		ret = edev->desc->ops->enable(edev);
>>> +		if (ret < 0)
>>> +			goto err;
>>> +	}
>> 
>> Is there any reason to call enable(edev) even when enable_count is already > 0 
>> while you do not call disable(edev) while enable_count > 0?
>> 
>> I think this may incur errors in the related device drivers.
>> (e.g., incorrect pairing of clk/runtime-pm/regulator enable/disable
>> at the device driver side)
>
>You're right. This part has potential errors. I'll fix it as following:
>If edev is already enabled, devfreq_event_enable_edev() will just return
>without any operation because devfreq-event(edev) can handle only one event
>at the same time.
> 
>	mutex_lock(&edev->lock);
>	if (edev->enable_count)
>		dev_warn(&edev->dev, "%s is already enabled\n", edev->desc->name);
>		ret = -EINVAL;
>		goto err;
>	}
>
>	if (edev->desc->ops && edev->desc->ops->enable) {		
>		ret = edev->desc->ops->enable(edev);
>		if (ret < 0)
>			goto err;
>	}
>	edev->enable_count++;

No, your suggested modification creates another bug.

It should not emit "warn" when enable_count > 0 at enable().
It is a natural behavior from drivers.
- You may have multiple drivers using edev.
- You may have multiple threads using edev.

Thus, the above 12 lines should be replaced with:

	if (edev->desc->ops && edev->desc->ops->enable &&
	    edev->enable_count == 0) {
		ret = edev->desc->ops->enable(edev);
		if (ret < 0)
			goto err;
	}
	edev->enable_count++;

>	
>
>> 
>>> +	edev->enable_count++;
>>> +err:
>>> +	mutex_unlock(&edev->lock);
>>> +
>>> +	return ret;
>>> +}
>>> +EXPORT_SYMBOL_GPL(devfreq_event_enable_edev);
>>> +
>>> +/**
>>> + * devfreq_event_disable_edev() - Disable the devfreq-event dev and decrease
>>> + *				  the enable_count of the devfreq-event dev.
>>> + * @edev	: the devfreq-event device
>>> + *
>>> + * Note that this function decrease the enable_count and disable the
>>> + * devfreq-event device. After the devfreq-event device is disabled,
>>> + * devfreq device can't use the devfreq-event device for get/set/reset
>>> + * operations.
>>> + */
>>> +int devfreq_event_disable_edev(struct devfreq_event_dev *edev)
>>> +{
>>> +	int ret = 0;
>>> +
>>> +	if (!edev || !edev->desc)
>>> +		return -EINVAL;
>>> +
>>> +	mutex_lock(&edev->lock);
>>> +	if (edev->enable_count > 0) {
>>> +		edev->enable_count--;
>>> +	} else {
>>> +		dev_warn(&edev->dev, "unbalanced enable_count\n");
>>> +		ret = -EINVAL;
>>> +		goto err;
>>> +	}
>>> +
>>> +	if (edev->desc->ops && edev->desc->ops->disable) {
>>> +		ret = edev->desc->ops->disable(edev);
>>> +		if (ret < 0) {
>>> +			edev->enable_count++;
>>> +			goto err;
>>> +		}

Anyway, have you seen other subsystems doing fall-back operations as you've
done by "edev->enable_count++" here? Or is this your own idea on falling back
from errors with a disable callback?

>>> +	}
>> 
>> You did it correctly with disable here;
>> not calling it when it is not required.

Uh..yeah.. the original patch was incorrect..

>
>As I explained, I'll fix it as following:
>
>	mutex_lock(&edev->lock);
>	if (!edev->enable_count) {
>		dev_warn(&edev->dev, "%s is already disabled\n", edev->desc->name);
>		ret = -EINVAL;
>		goto err;
>	}
>
>	if (edev->desc->ops && edev->desc->ops->disable) {
>		ret = edev->desc->ops->disable(edev);
>		if (ret < 0)
>			goto err;		
>	}
>	edev->enable_count--;

Uh.... I'd say it is still incorrect.

	mutex_lock(&edev->lock);
	if (!edev->enable_count) {
		dev_warn(&edev->dev, "%s is already disabled\n", edev->desc->name);
		ret = -EINVAL;
		goto err;
	}

	edev->enable_count--;
	if (edev->desc->ops && edev->desc->ops->disable &&
	    !edev->enable_count) {
		ret = edev->desc->ops->disable(edev);
		if (ret < 0)
			goto err;		
	}


>
>> 
>>> +err:
>>> +	mutex_unlock(&edev->lock);
>>> +
>>> +	return ret;
>>> +}
>>> +EXPORT_SYMBOL_GPL(devfreq_event_disable_edev);
>>> +
>> 
>> []
>>> +EXPORT_SYMBOL_GPL(devfreq_event_is_enabled);
>> []
>> 
>>> +EXPORT_SYMBOL_GPL(devfreq_event_set_event);
>> []
>> 
[]
>>> +int devfreq_event_reset_event(struct devfreq_event_dev *edev)
>>> +{
>>> +	int ret = 0;
>>> +
>>> +	if (!edev || !edev->desc)
>>> +		return -EINVAL;
>>> +
>>> +	if (!devfreq_event_is_enabled(edev))
>>> +		return -EPERM;
>>> +
>>> +	mutex_lock(&edev->lock);
>>> +	if (edev->desc->ops && edev->desc->ops->reset)
>>> +		ret = edev->desc->ops->reset(edev);
>>> +	mutex_unlock(&edev->lock);
>> 
>> In the context of the get_event() handling "load",
>> aren't you supposed to set total_event = event = 0; here?
>
>But, devfreq_event_reset_event() function cannot handle edata instance
>because edata is not included in edev. The edata instance is only used in devfreq_event_get_event().

Ah.. ok then.

>
[]

Cheers,
MyungJoo

Re: [PATCHv8 1/9] devfreq: event: Add new devfreq_event class to provide basic data for devfreq governor

[Chanwoo Choi]

Dear Myungjoo,

On 01/20/2015 03:59 PM, MyungJoo Ham wrote:
>>  
>> Dear Myungjoo,
>>
>> On 01/20/2015 01:34 PM, MyungJoo Ham wrote:
>>>>   
> []
>>>> +
>>>> +	mutex_lock(&edev->lock);
>>>> +	if (edev->desc->ops && edev->desc->ops->enable) {
>>>> +		ret = edev->desc->ops->enable(edev);
>>>> +		if (ret < 0)
>>>> +			goto err;
>>>> +	}
>>>
>>> Is there any reason to call enable(edev) even when enable_count is already > 0 
>>> while you do not call disable(edev) while enable_count > 0?
>>>
>>> I think this may incur errors in the related device drivers.
>>> (e.g., incorrect pairing of clk/runtime-pm/regulator enable/disable
>>> at the device driver side)
>>
>> You're right. This part has potential errors. I'll fix it as following:
>> If edev is already enabled, devfreq_event_enable_edev() will just return
>> without any operation because devfreq-event(edev) can handle only one event
>> at the same time.
>>
>> 	mutex_lock(&edev->lock);
>> 	if (edev->enable_count)
>> 		dev_warn(&edev->dev, "%s is already enabled\n", edev->desc->name);
>> 		ret = -EINVAL;
>> 		goto err;
>> 	}
>>
>> 	if (edev->desc->ops && edev->desc->ops->enable) {		
>> 		ret = edev->desc->ops->enable(edev);
>> 		if (ret < 0)
>> 			goto err;
>> 	}
>> 	edev->enable_count++;
> 
> No, your suggested modification creates another bug.
> 
> It should not emit "warn" when enable_count > 0 at enable().
> It is a natural behavior from drivers.
> - You may have multiple drivers using edev.
> - You may have multiple threads using edev.

The devfreq-event cannot be used in multiple drivers in current version
If multiple driver set the event to devfreq-event device by using
devfreq_event_set_event() at the same time, previous event will be ignored.

If multiple drivers want to use devfreq-event device at the same time,
I have to implement additional feature.

> 
> Thus, the above 12 lines should be replaced with:
> 
> 	if (edev->desc->ops && edev->desc->ops->enable &&
> 	    edev->enable_count == 0) {
> 		ret = edev->desc->ops->enable(edev);
> 		if (ret < 0)
> 			goto err;
> 	}
> 	edev->enable_count++;
> 
>> 	
>>
>>>
>>>> +	edev->enable_count++;
>>>> +err:
>>>> +	mutex_unlock(&edev->lock);
>>>> +
>>>> +	return ret;
>>>> +}
>>>> +EXPORT_SYMBOL_GPL(devfreq_event_enable_edev);
>>>> +
>>>> +/**
>>>> + * devfreq_event_disable_edev() - Disable the devfreq-event dev and decrease
>>>> + *				  the enable_count of the devfreq-event dev.
>>>> + * @edev	: the devfreq-event device
>>>> + *
>>>> + * Note that this function decrease the enable_count and disable the
>>>> + * devfreq-event device. After the devfreq-event device is disabled,
>>>> + * devfreq device can't use the devfreq-event device for get/set/reset
>>>> + * operations.
>>>> + */
>>>> +int devfreq_event_disable_edev(struct devfreq_event_dev *edev)
>>>> +{
>>>> +	int ret = 0;
>>>> +
>>>> +	if (!edev || !edev->desc)
>>>> +		return -EINVAL;
>>>> +
>>>> +	mutex_lock(&edev->lock);
>>>> +	if (edev->enable_count > 0) {
>>>> +		edev->enable_count--;
>>>> +	} else {
>>>> +		dev_warn(&edev->dev, "unbalanced enable_count\n");
>>>> +		ret = -EINVAL;
>>>> +		goto err;
>>>> +	}
>>>> +
>>>> +	if (edev->desc->ops && edev->desc->ops->disable) {
>>>> +		ret = edev->desc->ops->disable(edev);
>>>> +		if (ret < 0) {
>>>> +			edev->enable_count++;
>>>> +			goto err;
>>>> +		}
> 
> Anyway, have you seen other subsystems doing fall-back operations as you've
> done by "edev->enable_count++" here? Or is this your own idea on falling back
> from errors with a disable callback?

I removed "edev->enable_count++" when fail to diable devfreq-event
and modify it as following:

	+int devfreq_event_disable_edev(struct devfreq_event_dev *edev)
	+{
	+	int ret = 0;
	+
	+	if (!edev || !edev->desc)
	+		return -EINVAL;
	+
	+	mutex_lock(&edev->lock);
	+	if (!edev->enable_count) {
	+		dev_warn(&edev->dev,
	+			"%s is already disabled\n", edev->desc->name);
	+		goto err;
	+	}
	+	
	+	if (edev->desc->ops && edev->desc->ops->disable) {
	+		ret = edev->desc->ops->disable(edev);
	+		if (ret < 0)
	+			goto err;
	+	}
	+	edev->enable_count--;
	+err:
	+	mutex_unlock(&edev->lock);
	+
	+	return ret;
	+}
	+EXPORT_SYMBOL_GPL(devfreq_event_disable_edev);

> 
>>>> +	}
>>>
>>> You did it correctly with disable here;
>>> not calling it when it is not required.
> 
> Uh..yeah.. the original patch was incorrect..
> 
>>
>> As I explained, I'll fix it as following:
>>
>> 	mutex_lock(&edev->lock);
>> 	if (!edev->enable_count) {
>> 		dev_warn(&edev->dev, "%s is already disabled\n", edev->desc->name);
>> 		ret = -EINVAL;
>> 		goto err;
>> 	}
>>
>> 	if (edev->desc->ops && edev->desc->ops->disable) {
>> 		ret = edev->desc->ops->disable(edev);
>> 		if (ret < 0)
>> 			goto err;		
>> 	}
>> 	edev->enable_count--;
> 
> Uh.... I'd say it is still incorrect.

I explained it about this problem on the upper.

> 
> 	mutex_lock(&edev->lock);
> 	if (!edev->enable_count) {
> 		dev_warn(&edev->dev, "%s is already disabled\n", edev->desc->name);
> 		ret = -EINVAL;
> 		goto err;
> 	}
> 
> 	edev->enable_count--;
> 	if (edev->desc->ops && edev->desc->ops->disable &&
> 	    !edev->enable_count) {
> 		ret = edev->desc->ops->disable(edev);
> 		if (ret < 0)
> 			goto err;		
> 	}

[snip]

Best Regards,
Chanwoo Choi