[PATCH v1 4/7] thermal: intel: intel_soc_dts_iosf: Change initialization ordering

Rafael J. Wysocki
2023-08-10T19:17:50Z

The initial configuration of trip points in intel_soc_dts_iosf_init()
takes place after registering the sensor thermal zones which is
potentially problematic, because it may race with the setting of trip
point temperatures via sysfs, as there is no synchronization between it
and sys_set_trip_temp().

To address this, change the initialization ordering so that the trip
points are configured prior to the registration of thermal zones.

Accordingly, change the cleanup ordering in intel_soc_dts_iosf_exit()
to remove the thermal zones before resetting the trip points.

Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
---
drivers/thermal/intel/intel_soc_dts_iosf.c | 25 ++++++++++++++++---------
1 file changed, 16 insertions(+), 9 deletions(-)

Index: linux-pm/drivers/thermal/intel/intel_soc_dts_iosf.c
===================================================================
--- linux-pm.orig/drivers/thermal/intel/intel_soc_dts_iosf.c
+++ linux-pm/drivers/thermal/intel/intel_soc_dts_iosf.c
@@ -398,30 +398,37 @@ struct intel_soc_dts_sensors *intel_soc_

for (i = 0; i < SOC_MAX_DTS_SENSORS; ++i) {
sensors->soc_dts[i].sensors = sensors;
- ret = add_dts_thermal_zone(i, &sensors->soc_dts[i],
- read_only_trip_count);
- if (ret)
- goto err_free;
- }

- for (i = 0; i < SOC_MAX_DTS_SENSORS; ++i) {
ret = configure_trip(&sensors->soc_dts[i], 0,
THERMAL_TRIP_PASSIVE, 0);
if (ret)
- goto err_remove_zone;
+ goto err_reset_trips;

ret = configure_trip(&sensors->soc_dts[i], 1,
THERMAL_TRIP_PASSIVE, 0);
if (ret)
+ goto err_reset_trips;
+ }
+
+ for (i = 0; i < SOC_MAX_DTS_SENSORS; ++i) {
+ ret = add_dts_thermal_zone(i, &sensors->soc_dts[i],
+ read_only_trip_count);
+ if (ret)
goto err_remove_zone;
}

return sensors;
+
err_remove_zone:
for (i = 0; i < SOC_MAX_DTS_SENSORS; ++i)
remove_dts_thermal_zone(&sensors->soc_dts[i]);

-err_free:
+err_reset_trips:
+ for (i = 0; i < SOC_MAX_DTS_SENSORS; i++) {
+ configure_trip(&sensors->soc_dts[i], 0, 0, 0);
+ configure_trip(&sensors->soc_dts[i], 1, 0, 0);
+ }
+
kfree(sensors);
return ERR_PTR(ret);
}
@@ -432,9 +439,9 @@ void intel_soc_dts_iosf_exit(struct inte
int i;

for (i = 0; i < SOC_MAX_DTS_SENSORS; ++i) {
+ remove_dts_thermal_zone(&sensors->soc_dts[i]);
configure_trip(&sensors->soc_dts[i], 0, 0, 0);
configure_trip(&sensors->soc_dts[i], 1, 0, 0);
- remove_dts_thermal_zone(&sensors->soc_dts[i]);
}
kfree(sensors);
}