From: Daniel Lezcano <daniel.lezcano@linaro.org>
To: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Cc: Kukjin Kim <kgene.kim@samsung.com>,
Tomasz Figa <t.figa@samsung.com>,
Sachin Kamat <sachin.kamat@linaro.org>,
Viresh Kumar <viresh.kumar@linaro.org>,
"Rafael J. Wysocki" <rjw@rjwysocki.net>,
Kyungmin Park <kyungmin.park@samsung.com>,
linux-samsung-soc@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, linux-pm@vger.kernel.org,
linux-kernel@vger.kernel.org, linaro-kernel@lists.linaro.org
Subject: Re: [PATCH 6/7] ARM: EXYNOS: PM: fix register setup on EXYNOS4x12 for AFTR mode code
Date: Mon, 02 Jun 2014 18:05:04 +0200 [thread overview]
Message-ID: <538CA0B0.2030200@linaro.org> (raw)
In-Reply-To: <2762097.QhkViWyNLQ@amdc1032>
On 06/02/2014 02:08 PM, Bartlomiej Zolnierkiewicz wrote:
>
> Hi,
>
> On Friday, May 16, 2014 11:03:11 AM Daniel Lezcano wrote:
>> On 05/05/2014 12:57 PM, Bartlomiej Zolnierkiewicz wrote:
>>> Add S5P_CENTRAL_SEQ_OPTION register setup for EXYNOS4x12 to AFTR
>>> mode code. Without this setup AFTR mode doesn't show any benefit
>>> over WFI one. When this setup is applied AFTR mode reduces power
>>> consumption by ~12% (as measured on Trats2 board).
>>>
>>> This change is a preparation for adding secure firmware support to
>>> EXYNOS cpuidle driver.
>>>
>>> Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
>>> ---
>>> arch/arm/mach-exynos/pm.c | 4 ++++
>>> 1 file changed, 4 insertions(+)
>>>
>>> diff --git a/arch/arm/mach-exynos/pm.c b/arch/arm/mach-exynos/pm.c
>>> index 18f6bf8..3922968 100644
>>> --- a/arch/arm/mach-exynos/pm.c
>>> +++ b/arch/arm/mach-exynos/pm.c
>>> @@ -391,6 +391,10 @@ static int exynos_cpu_pm_notifier(struct notifier_block *self,
>>> case CPU_PM_ENTER:
>>> if (cpu == 0) {
>>> exynos_pm_central_suspend();
>>> + if (soc_is_exynos4212() || soc_is_exynos4412())
>>> + __raw_writel(S5P_USE_STANDBY_WFI0 |
>>> + S5P_USE_STANDBY_WFE0,
>>> + S5P_CENTRAL_SEQ_OPTION);
>>
>> Why not put this code in the exynos_enter_aftr() ?
>
> I would prefer to keep this code close to exynos_pm_central_suspend()
> because exynos_pm_suspend() (which calls exynos_pm_central_suspend()
> too) also contains S5P_USE_STANDBY_WF[I,E]0 setting code (done for all
> SoCs). If possible I would like to make this code common for AFTR &
> suspend in the future (once it is tested on Exynos4210 and Exynos5250)
> by moving S5P_USE_STANDBY_WF[I,E]0 setting to exynos_pm_central_suspend()
> and doing it for all SoCs. Are you okay with this?
Yeah, no problem.
>>> exynos_cpu_save_register();
>>> }
>>> break;
>
> Best regards,
> --
> Bartlomiej Zolnierkiewicz
> Samsung R&D Institute Poland
> Samsung Electronics
>
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
next prev parent reply other threads:[~2014-06-02 16:05 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-05-05 10:57 [PATCH 0/7] ARM: EXYNOS: cpuidle: fix AFTR mode on boards with secure firmware enabled Bartlomiej Zolnierkiewicz
2014-05-05 10:57 ` [PATCH 1/7] arm: firmware: Check firmware is running or not Bartlomiej Zolnierkiewicz
2014-05-05 10:57 ` [PATCH 2/7] ARM: EXYNOS: add support for firmware-assisted c15resume Bartlomiej Zolnierkiewicz
2014-05-05 10:57 ` [PATCH 3/7] ARM: EXYNOS: add AFTR mode support to firmware do_idle method Bartlomiej Zolnierkiewicz
2014-05-05 10:57 ` [PATCH 4/7] ARM: EXYNOS: PM: replace EXYNOS_BOOT_VECTOR_* macros by static inlines Bartlomiej Zolnierkiewicz
2014-05-16 8:59 ` Daniel Lezcano
2014-05-05 10:57 ` [PATCH 5/7] ARM: EXYNOS: PM: use c15resume firmware method if secure firmware is enabled Bartlomiej Zolnierkiewicz
2014-05-05 10:57 ` [PATCH 6/7] ARM: EXYNOS: PM: fix register setup on EXYNOS4x12 for AFTR mode code Bartlomiej Zolnierkiewicz
2014-05-16 9:03 ` Daniel Lezcano
2014-06-02 12:08 ` Bartlomiej Zolnierkiewicz
2014-06-02 16:05 ` Daniel Lezcano [this message]
2014-05-05 10:57 ` [PATCH 7/7] ARM: EXYNOS: cpuidle: add secure firmware support to " Bartlomiej Zolnierkiewicz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=538CA0B0.2030200@linaro.org \
--to=daniel.lezcano@linaro.org \
--cc=b.zolnierkie@samsung.com \
--cc=kgene.kim@samsung.com \
--cc=kyungmin.park@samsung.com \
--cc=linaro-kernel@lists.linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=rjw@rjwysocki.net \
--cc=sachin.kamat@linaro.org \
--cc=t.figa@samsung.com \
--cc=viresh.kumar@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).